Kathrein Mobile Communication – Now Part of Ericsson

Ericsson Antenna Technology Germany GmbH • Klepperstraße 26 • 83026 Rosenheim • Germany

Ericsson Antenna Technology Germany GmbH Klepperstraße 26 83026 Rosenheim Kathrein Mobile Germany Phone: +49 8031 184-0 Fax: +49 8031 184-306 Communication www.kathrein.com Company Responsible: – now part of Markus Feld VAT Reg. No.: DE 324 954 029 Tax ID No.: 103/5725/3930

Ericsson BNP Paribas IBAN: NL05 BNPA 0227 7141 56 BIC: BNPANL2AXXX Zum 1. Oktober 2019 ist die Kathrein Mobile Communication die Ericsson Antenna Technology Germany GmbH (im Folgenden auch „EAG“), eine mit Gesellschaftsvertrag vom 16. Januar 2019 neu gegründete Gesellschaft mit beschränkter Haftung (GmbH) nach deutschem Recht mit Sitz in Rosenheim (Geschäftsanschrift: Prinzenallee 21, 40549 Düsseldorf). EAG ist im Handelsregister B des Amtsgerichts Traunstein unter der Nr. HRB 27988 eingetragen und hat ein Stammkapital von derzeit EUR 2.000.000,00. EAG wird vertreten durch den Geschäftsführer Markus Feld. Alleinige Gesellschafterin von EAG ist die Telefonaktiebolaget LM Ericsson (publ), eine börsennotierte Aktiengesellschaft nach schwedischem Recht.

Die neuen Firmendaten lauten seither wie folgt: Ericsson Antenna Technology Germany GmbH Klepperstraße 26 83026 Rosenheim, Germany UST-Ident-Nr: DE 324 954 029 Steuer-Nr.: 103/5725/3930

As of 1 October 2019, Kathrein Mobile Communication is Ericsson Antenna Technology Germany GmbH (hereinafter also referred to as “EAG”), a limited liability company under German law, newly established by articles of association dated 16 January 2019, with its head office in Rosenheim (business address: Prinzenallee 21, 40549 Düsseldorf, Germany). EAG is registered in the commercial register, section B, of Amtsgericht Traunstein (district court Traunstein) under the number HRB 27988 and has a share capital of currently EUR 2,000,000. EAG is represented by managing director Markus Feld. The sole shareholder of EAG is Telefonaktiebolaget LM Ericsson (publ), a listed stock corporation under Swedish law.

The new company data are as follows:

9360000644 Ericsson Antenna Technology Germany GmbH Klepperstraße 26 83026 Rosenheim, Germany VAT Reg. No.: DE 324 954 029 Tax ID No.: 103/5725/3930

Read more at: ericsson.com/en/networks/kathrein Gender Adapter for FlexRET

Converts the AISG out (female) to an AISG in (male) port in order to operate the FlexRET with two BTS. Only for FlexRET 86010153V01.

Type No. 86010162 Protocols compliant to 3GPP/AISG 2.0 Input voltage range V 10 ... 30 (pin 6) Connectors 1 x 8 pin connector (male) according to IEC 60130-9; according to AISG C485 1 x 8 pin connector (female) according to IEC 60130-9; according to AISG C485 Female mates with FlexRET Hardware interfaces RS 485A/B (pin 5, pin 3); power supply (pin 6); DC return (pin 7); according to AISG / 3GPP Temperature range °C –40 … +60 Protection class IP 67 (installed) Surge current capability AISG interface (each pin) in combination with FlexRET 2.5 kA (10/350 µs) 8 kA (8/20 µs) according to IEC 61000-4-5 Housing material Connector shell: Zinc die cast Ni plated; Contacts: Ag plated Weight g 45 lb 0.099 Packing size mm 43 x 20 x 20 (H x W x D) inches 1.7 x 0.78 x 0.78 Dimensions mm 43 x 20 x 20 (H x W x D) inches 1.7 x 0.78 x 0.78

Standards: EN 60950-1 (Safety) EN 60950-22 (Safety – Equipment installed outdoor) ETS 300019-1-4 (Environmental) UL 60950-1; 1st edition Certification: CE Scope of supply: Gender Adapter Notice: The Gender Adapter is solely to be used in combination with the FlexRET module 86010153V01. A combination with other modules, especially with Antenna the FlexRET module 86010153, must be avoided since this could lead to un expected behaviour in the FlexRET module and could cause overvoltage in the primary power supply. For avoidance of doubt, the combination with any other module, with exception of the FlexRET module 86010153V01, could lead to a damage. In Flex no event will Kathrein, its affiliates and/or subsidiaries be liable for di- RET

rect, incidental, consequential, special, indirect damages arising from or Gender Adapter relating to the combination with another module except FlexRET module (converts “AISG out” 86010153V01. These limitations will apply even if Kathrein has been advised of to “AISG in”) the possibility of such damages and whether such damages are forseeable or not.

BTS 1 BTS 2

+ + AISG out AISG out

86010153 + 86010162 86010153V01 + 86010162

936.5262b Subject to alteration. In combination with 86010153: In combination with 86010153V01: Gender Adapter is not usable. Gender Adapter can be used.

Installation introduction 1) The Gender Adapter must be connected to the FlexRET module prior to connecting it to the cable. The Gender Adapter is marked with an arrow. Please connect the adapter to the FlexRET module output (marked with “out”) in direction of the arrow and fix it with a tightening torque of 1.0–1.5 Nm (‘hand-tightened’). The connector should be tightened by hand or by a special screw driver (order no. 85010080).

2) Connect a control cable to the AISG input of the FlexRET. The tightening torque for fixing the connector must be 1.0–1.5 Nm (‘hand-tightened’). The connector should be tightened by hand or by a special screw driver (order no. 85010080). See also the data sheet for Kathrein AISG-cable (86010007, ...).

Please note: To ensure the tightness of the RET System, Kathrein recommends the use of Kathrein components only.

3) Address the FlexRET single units to the BTS as desired.

Please note: At the input where the Gender Adapter is connected, the serial number of the FlexRET module is in addition to the array ID also extended by the character “G” (example: CSG3415804G-Y1). The serial number of the FlexRET module at the original AISG input remains as before, e.g. CSG3415804-Y2.

4) You can also download a Site-Sharing-Configuration file on the FlexRET.

Please note: To use the Gender Adapter in combination with a site sharing configuration file, the used FlexRET needs to be updated with the latest FlexRET firmware version FW_V02.03.00. The latest FlexRET firmware can be downloaded from the service portal under www.kathrein.com. To create a site sharing configuration file please use the FlexRET site-sharing-configurator which is also available at the service portal under www.kathrein.com. If the gender adapter is connected, the FlexRET accepts a site sharing configuration file. If the Gender Adapter is disconnected, the FlexRET operates in Standard mode and ignores any previously stored site sharing configuration file. The logical interface on both ports can be operated in AISG 2.0 (3GPP) or in AISG 1.1 mode. It is not possible to use different protocol modes on port A and B. The FlexRET can be operated in single-RET or multi-RET mode. An operation in different RET modes on port A and B is not possible. 936.5262b Subject to alteration.