M8007 >> MISSES’ PANTS

02 PIECES AND NOTIONS 03 CHARTS

04 CUTTING LAYOUTS 07 PATTERN MARKINGS 08 SEWING INSTRUCTIONS

SKILL LEVEL: EASY M8007 >> PIECES AND NOTIONS

Find the Perfect Fit!

THINGS YOU NEED: >> One 7” Zipper, Two Hook & Eye Closures.

SUGGESTED FABRICS: >> Denim, Twill, Chino, Cotton Blends.

A C B

A B C

Your printed tile pieces should be assembled before you move on to this step!

PIECES (10) 10 PATTERN PIECES 10 PIEZAS DE PATRON PANTS A, B, C 1 FRONT 2 LEFT FLY 9B 3 RIGHT FLY FACING 6 4 5 4 SIDE FRONT 1 2 5 SIDE BACK 10 6 BACK B 7 CARRIER 7 8 WAISTBAND 3 9 FRONT POCKET B 10 BACK POCKET B

8

FABRIC AND SIZE CHARTS MCCALL'S >> PDF PATTERNS 2 M8007 >> FABRIC AND SIZE CHARTS

CHARTS

YARDAGE CHARTS SIZES 6 8 10 12 14 16 18 20 22 VIEW A 45*** 27/8 27/8 27/8 27/8 27/8 27/8 27/8 27/8 27/8 yds. 60*** 25/8 25/8 25/8 25/8 25/8 27/8 27/8 27/8 27/8 yds. VIEW B 45*** 31/8 31/8 31/8 31/8 31/8 31/8 31/8 31/8 31/8 yds. 60*** 25/8 25/8 25/8 25/8 25/8 27/8 27/8 27/8 27/8 yds. VIEW C 45*** 13/4 13/4 13/4 13/4 13/4 13/4 13/4 13/4 13/4 yds. 60*** 13/4 13/4 13/4 13/4 13/4 13/4 13/4 13/4 13/4 yds. CONTRAST C 45*** 13/8 13/8 13/8 13/8 13/8 13/8 13/8 13/8 15/8 yds. 60*** 13/8 13/8 13/8 13/8 13/8 13/8 13/8 13/8 13/8 yds. FUSIBLE INTERFACING A,B,C 18,20 1 1 11/8 11/8 11/8 11/4 11/4 13/8 13/8 yds.

FINISHED GARMENT MEASUREMENTS SIZES 6 8 10 12 14 16 18 20 22 WIDTH, EACH LEG A B C 311/2 32 321/2 33 331/2 34 341/2 35 351/2 in. SIDE LENGTH FROM WAIST A B C 431/2 431/2 431/2 431/2 431/2 431/2 431/2 431/2 431/2 in.

BODY MEASUREMENTS SIZES 6 8 10 12 14 16 18 20 22 BUST 301/2 311/2 321/2 34 36 38 40 42 44 in. WAIST 23 24 25 261/2 28 30 32 34 37 in. HIP 321/2 331/2 341/2 36 38 40 42 44 46 in. BACK WAIST LENGTH 151/2 153/4 16 161/4 161/2 163/4 17 171/4 171/2 in.

FABRIC AND SIZE CHARTS MCCALL'S >> PDF PATTERNS 3 M8007 >> CUTTING LAYOUTS

CUTTING AND MARKING >> SHRINK FABRIC if not labeled pre-shrunk. Press. >> CIRCLE LAYOUT for View, Size, Fabric Width. >> Use WITH NAP layout for fabrics with one-way designs, nap, pile or surface shading. Because most knits have surface shading, a with nap layout is used. >> For DOUBLE THICKNESS (WITH FOLD), fold fabric with right sides together. B >> *DOUBLE THICKNESS (WITHOUT FOLD), for fabrics with nap, fold fabric A crosswise, right sides together. Mark as shown. Cut along crosswise fold of fabric (A). Turn upper layer 180° so arrows go in same direction and place over lower layer, right sides together (B). >> For SINGLE THICKNESS, place fabric right side up. (For Fur Pile fabrics, place pile side down.)

>> Before CUTTING, place all pieces on fabric according to layout. Pin. (Layouts show approximate position of pattern pieces; position may vary according to your pattern size.) >> Cut other pieces first, allowing enough fabric to cut this piece. Open fabric. Cut piece on single layer of fabric with piece face up on right side of fabric. >> Cut accurately, cutting notches outward. >> Before removing pattern, TRANSFER MARKINGS and lines of construction to WRONG SIDE of fabric, using Pin and Chalk Pencil method or Tracing Paper and Dressmaker Wheel. Markings needed on right side of fabric should be thread traced. NOTE: Broken-line boxes (a! b! c!) in layouts respresent pieces cut by measurements provided. >> Prewash your fabric using a method that’s suitable for the fabric type. >> Fold fabric with right sides together, matching SELVAGES. >> Pin your pattern pieces to the fabric as shown below and cut them out using a sharp pair of dressmaker’s shears.

CUTTING LAYOUTS MCCALL'S >> PDF PATTERNS 4 M8007 >> CUTTING LAYOUTS

PANTS A PANTS B USE PIECES/USE PIEZAS: 1,2,3,4,5,6,7 & 8 45” (115 CM) USE PIECES/USE PIEZAS: 1,2,3,4,5,6,7,8,9 & 10 WITH OR WITHOUT NAP 45” (115 CM) ALL SIZES WITH OR WITHOUT NAP ALL SIZES SELVAGE SELVAGE

SELVAGES SELVAGES 8 8 4 5 4 5 10 2 2 1 6 1 6 9 7 7 3 FOLD SELVAGE 3 FOLD SELVAGE

45" */** m8007 PANTS [B] Sz 22 P−1007 45" */** 60” m8007 (150 PANTS CM) [A] Sz 22 P−1001 60” (150 CM) WITH OR WITHOUT NAP WITH OR WITHOUT NAP SIZES 6-8-10-12-14 SIZES 6-8-10-12-14 SELVAGES SELVAGES

5 5 6 6 3 3 7 1 2 7 1 2 4 9 4 8 10 FOLD 8 FOLD

60" */** m8007 PANTS [B] Sz 14 P−1011 60" */** m8007 PANTS [A] Sz 14 P−1004

60” (150 CM) 60” (150 CM) WITH OR WITHOUT NAP WITH OR WITHOUT NAP SIZES 16-18-20-22 SIZES 16-18-20-22 SELVAGE SELVAGE

SELVAGES SELVAGES

5 5 6 8 6 8

2 7 2 7 9 3 1 3 1 4 4 10 FOLD SELVAGE FOLD SELVAGE

60" */** m8007 PANTS [A] Sz 22 P−1003 60" */** m8007 PANTS [B] Sz 22 P−1009

CUTTING LAYOUTS MCCALL'S >> PDF PATTERNS 5 M8007 >> CUTTING LAYOUTS 45” (115 CM) PANTS C WITH OR WITHOUT NAP SIZE/TALLA 22 USE PIECES/USE PIEZAS: 1,2,3,5,7 & 8 SELVAGES 45” (115 CM) WITH OR WITHOUT NAP ALL SIZES 6 SELVAGE 4 FOLD

2 3 SELVAGES 60” (150 CM) 8 WITH45" */** OR m8007 WITHOUT CONTRAST NAP [C] Sz 22 P−1018 5 ALL SIZES SELVAGES 1 6 7 FOLD SELVAGE

60” (150 CM) 45" */** m8007WITH OR PANTS WITHOUT [C] Sz NAP22 P−1013 4 ALL SIZES SELVAGE FOLD

60" */** m8007 CONTRAST [C] Sz 22 P−1022 FUSIBLE INTERFACING A,B,C SELVAGES USE PIECES/USE PIEZAS: 2,3 & 8 18”,20” (46,51 CM)

ALL SIZES 5 8 SELVAGE 3 7 2 2 1 3 FOLD SELVAGE 8 SELVAGE

60" */** m8007 PANTS [C] Sz 22 P−1015 CONTRAST C 18" ** m8007 FUSIBLE INTERFACING [A,B,C] Sz 22 P−1024 (SIDE FRONT) / (COSTADO DEL FRENTE) USE PIECES/USE PIEZAS: 4 & 6 45” (115 CM) WITH OR WITHOUT NAP SIZES 6-8-10-12-14-16-18-20 SELVAGES

6

4 FOLD

45" */** m8007 CONTRAST [C] Sz 20 P−1021

CUTTING LAYOUTS MCCALL'S >> PDF PATTERNS 6 M8007 >> PATTERN MARKINGS

FOLDLINE SYMBOLS to place on used for matching fold of fabric. pieces together or NOTCHES other construction single, double or details. triple triangular markings used for matching pieces together.

LENGTHEN OR SHORTEN LINES two parallel lines where you make the pattern piece longer or shorter. DARTS “V” shaped broken lines; used to give shape to the garment.

TO LENGTHEN slash between adjustment lines; MEASUREMENTS spread amount as indicates Bustline, needed, keeping Waistline, Hip or Biceps; edges parallel; refers to circumference of tape over paper. finished garment.

GRAINLINE to place on straight HEM grain of fabric parallel ALLOWANCE TO SHORTEN to selvage. the measurement crease along used to turn up adjustment line; make your hem. a fold half the amount needed; tape in place.

PATTERN MARKINGS MCCALL'S >> PDF PATTERNS 7 M8007 >> SEWING INSTRUCTIONS

SEAM ALLOWANCES: >> Use 5/8" (1.5 cm) seam allowances unless otherwise indicated. >> Pin or baste seams, right side together, matching notches. Fit garment before stitching major seams. >> Press seam allowances flat; then open unless otherwise stated. Clip where necessary so they lie flat.

The following terms appear in BOLD TYPE throughout your sewing instructions!

>> EDGESTITCH >> SLIPSTITCH Stitch close to finished edge or seam. Slide needle through a folded edge, then pick up a thread of underneath fabric. >> FINISH Stitch 1/4” (6mm) from raw edge and finish with >> STAYSTITCH one of the following: (1) Pink OR (2) Overcast OR (3) Stitch 1/8” (3mm) from seamline in seam allowance Turn in along stitching and stitch close to fold OR (4) (usually 1/2” (13mm) from raw edge). Overlock.

OPTIONAL FOR HEMS: Apply Seam Binding. >> TOPSTITCH On outside, stitch 1/4” (6mm) from edge, seam or previous stitching, using presser foot as guide, or >> NARROW HEM stitch where indicated in instructions. Turn in hem; press, easing in fullness if necessary. Open out hem. Turn in again so raw edge is along crease; press. Turn in along crease; stitch. >> UNDERSTITCH Open out facing or underside of garment; stitch to seam allowance close to seam.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 8 M8007 >> SEWING INSTRUCTIONS PANTS A, B, C NOTE: The first view mentioned will be illustrated unless otherwise indicated. INTERFACING

Trim corners of INTERFACING, as shown. Fuse interfacing to wrong side of each 2 3 matching FABRIC section, following manufacturer’s instructions.

8

FRONT

Stitch FRONT (1) sections, right sides together at center front, between square and notch.

1

Turn left front to inside along foldline. Press.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 9 M8007 >> SEWING INSTRUCTIONS Place closed zipper (face up) under left front opening edge, placing zipper stop at large circle and zipper teeth close to pressed edge. Baste close to pressed edge. NOTE: Zipper will extend above upper edge.

Pin LEFT FLY (2) sections, right sides together. Stitch long curved edge. Trim seam allowances. 2

Turn right side out. Press. Baste raw edges together.

On inside, lap left fly to left front over zipper, having raw edges even. Baste through all thicknesses.

On outside, stitch left front close to pressed edge, through all thicknesses, using a zipper foot.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 10 M8007 >> SEWING INSTRUCTIONS

FINISH long curved edge of RIGHT FLY FACING (3). 3

With right sides together, pin right fly facing to right front opening edge. Stitch, ending at square. Trim seam allowances.

UNDERSTITCH facing.

Turn right fly facing to inside. Press.

Lap right front over left, matching centers. Baste close to edge, through all thicknesses.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 11 M8007 >> SEWING INSTRUCTIONS Pin remaining zipper tape to right fly facing, keeping front and left fly free. Using a zipper foot, stitch in place through center of zipper tape, as shown. Open zipper. Turn right fly facing down. Baste across upper edge.

Close zipper. On outside, stitch right front along stitching line, keeping left fly free.

On inside, tack lower edge of left fly and right fly facing together, as shown.

SIDE FRONT

View B:

FINISH slanted edge of FRONT POCKET (9) with a 5/8” (1.5cm) NARROW HEM. 9

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 12 M8007 >> SEWING INSTRUCTIONS Turn lower edge of pocket to inside. Press.

Pin pocket to SIDE FRONT (4), matching notches and circles, and having side edges even. EDGESTITCH lower edge. (Pocket does not lie flat). Baste side edges together.

4

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 13 M8007 >> SEWING INSTRUCTIONS Views A, B, C:

Pin SIDE FRONT (4) to front, matching notches. Stitch. Press seam allowances toward side front. 4 4

TOPSTITCH side front.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 14 M8007 >> SEWING INSTRUCTIONS BACK

Stitch dart in SIDE BACK (5). Press fold of dart toward center.

5

Pin side back sections, right sides together. Stitch center back seam.

STAYSTITCH side edge of BACK (6) above lower notch.

6

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 15 M8007 >> SEWING INSTRUCTIONS

Pin back sections, right sides together. Stitch center back seam.

Pin back to side back, right sides together, matching notches, clipping side back where necessary. Stitch. Press seam allowances toward side back.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 16 M8007 >> SEWING INSTRUCTIONS

TOPSTITCH side back.

View B:

Press under 1/4” (6mm) on upper edge of each BACK POCKET (10). Turn upper edge to outside along 10 foldline. Stitch ends. Trim seam allowances.

Turn upper edge of pocket to inside, turning in remaining seam allowances and folding in corners diagonally. Press. Baste close to inner pressed-under edge. TOPSTITCH along basting.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 17 M8007 >> SEWING INSTRUCTIONS Pin pocket to back, matching circles. TOPSTITCH sides and lower edge.

Views A, B, C:

Stitch back to front at inner leg.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 18 M8007 >> SEWING INSTRUCTIONS

Stitch remainder of crotch seam to notch in front. Stitch again 1/4” (6mm) away in seam allowances between notches. Trim close to second stitching.

Stitch back to front at sides.

CARRIERS

Press under 5/8” (1.5cm) on long edges 7 of CARRIER (7).

With wrong sides together, fold carrier along foldline, having edges even. Press. EDGESTITCH long edges.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 19 M8007 >> SEWING INSTRUCTIONS

Cut carrier into five sections, each 4-1/4” (11cm) long. NOTE: Extra length has been allowed. Press under 5/8” (1.5cm) on one end of each carrier. Trim pressed-under edge to 3/8” (1cm).

On outside, center remaining end of carriers over squares on pants, having ends even with raw edge, as shown. Baste along seamline. Stitch across carriers at squares.

WAISTBAND

STAYSTITCH upper edge of pants between notches.

Pin interfaced WAISTBAND (8) section to upper edge of pants and left fly, placing large circles to opening edges, matching 8 notches, centers and squares to side seams, clipping pants where necessary. Baste. Stitch. Trim, trimming excess zipper. Press seam allowances toward waistband. (Uninterfaced waistband section will be used as facing.) Press under 5/8” (1.5cm) on notched edge of waistband FACING, easing in fullness. Trim pressed-under edge to 3/8” (1cm).

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 20 M8007 >> SEWING INSTRUCTIONS Pin facing to waistband, right sides together. Stitch ends and upper edge. Trim seam allowances.

Turn facing to inside. Press. SLIPSTITCH pressed-under edge over seam. EDGESTITCH all edges of waistband.

Turn carriers up. Pin to upper edge of waistband, centering over squares. EDGESTITCH in place, through all thicknesses.

FINISHING Hems:

Turn up a 1-1/4” (3.2cm) hem on lower edge of pants. Baste close to fold. Machine-baste 1/4” (6mm) from raw edge. Pull up bobbin thread and adjust fullness; shrink out with steam. Turn under 1/4” (6mm) on raw edge. Baste hem in place close to upper edge. Press. TOPSTITCH hem along upper basting.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 21 M8007 >> SEWING INSTRUCTIONS Closures:

On inside, sew two hook closures to right end of waistband, as shown. On outside, sew eye closures to left end of waistband, opposite hook closures.

SEWING INSTRUCTIONS MCCALL'S >> PDF PATTERNS 22 Congrats!

You've completed your sewing adventure!

SHARE YOUR look!

Post your pattern and tag us at @McCALLPATTERNCOMPANY and use #MCCALLSPATTERNS for a chance to be featured on our social media!

Look for more McCall's PDF patterns at McCALLPATTERN.COM

1-800-255-2762

Copyright © 2019 CSS Industries, Inc. All Rights Reserved. Sold for individual home use only and not for commercial or manufacturing purposes.