Uniforms - State Police Specifications (A-F)

SPECIFICATION A NEW HAMPSHIRE STATE POLICE SHORT SLEEVE SUMMER SHIRT RAEFORD MILLS, ITEM #571-590 GENDER : MALE AND FEMALE

MATERIAL Raeford Mills style #571-590, 8-8 1/2 oz. 2 ply Tropical weave. 553 Dacron/Polyester/453 Wool. Dark Green color. Shoulder straps and pocket flaps to be piped with style 571-437. Taupe color.

STYLE Modified Military Officers style with piped shoulder straps and pocket flaps.

FRONT Six (6) button front with no collar button, with approximately four (4) inch facings. Facings are to be merged with one eighth ( l/8) inch narrow gauge over lay stitch, with eleven ( 1 1) stitches per inch. Left facing to have one and half ( l 12/ ) inch pleat attached with four (4) rows of stitching. Front pleat to be interlined with poly-cotton VIKING PRESS canvas. Left facing to contain six (6) vertical button holes. Two (2) extra buttons are to be attached to bottom of right front.

ZIPPER FRONT With a fifteen (15) inch brass zipper (nylon is not acceptable) .The zipper is to be functional. The front shall contain one ( l) functional metal button and four (4) non-functional metal buttons and buttonholes with one ( l) functional bone button at bottom below zipper. All non-functional buttonholes to be cut one quarter ( l/4) inch to accept metal button shank

BADGE TAB 1 Badge tab to be made of self-cloth two and one quarter (2 /..) inches long and one ( 1) inch 1 wide, with two (2) black metal eyelets set one and one quarter ( l /.. ) inch apart. Badge tab to be set one ( l) inch above left pocket flap.

BACK Pointed western yoke to finish five (5) inches below collar seam at point, double stitched. Yoke is to be lined with matching 70 denier nylon taffeta.

COLLAR Convertible sport collar to be two (2) piece and measure three (3) inches long at points, with collar approximately one and half ( 1 12/ ) inches high at back after turned down. Permanent plastic collar stays to be slanted in collar so not to show stitching on top or bottom of outer leaf. Collar to be top stitched one quarter (1/4) inch from edge. NOTE: the convertible collar to be interlined with poly-cotton COTTON PRESS canvas.

POCKETS There shall be two (2) plain patch pockets approximately five and one quarter (5 1/.i) inch by six (6) inch deep, not including the flap. Pockets to have a top stitched crease with left front pocket to have top stitched pen and pencil opening of one and one half ( l 12/ ) inch on right side of pocket. The lower corners of pockets are to be mitered. Uniforms - State Police Specifications (A-F)

POCKET FLAPS There shall be two (2) scalloped flaps of self-material with one eighth { 1/8) inch taupe piping, Raeford 571-437. Pocket flaps to be sewn and turned, then top stitched on edge. Left flap to have one and half ( 1 Y2) inch opening at top for pencil on right side of flap. Pocket flaps to be placed approximately seven (7) inches down from shoulder seam {seven (7) inches to vary according to size of shirt) . Pocket flap to be sewn down on each side of pocket to prevent access to pocket. The pocket flaps shall contain one ( 1) non-functional metal button centered.

SHOULDER STRAPS To measure two (2) inches wide at sleeve head and extend to within approximately one quarter {I /4) inch of collar. Shoulder straps to be sewn, turned and top stitched with one {I ) row of stitching. Straps are to be piped with contrasting taupe fabric. Straps to be set into each sleeve head when the sleeves are joined. Straps to be securely cross-stitched for a distance of approximately two and one half (2 1h) inches from the sleeve head and to contain one buttonhole set one half ( l/2) inch from pointed end. Shirts are to be made to accommodate a metal button on the shoulder strap. A one quarter { lI4) inch buttonhole to be placed in the shirt to accommodate a metal button with a metal button guard made of one ( l) inch black tape set into collar seam and extending approximately one half { l/2) inch beyond buttonhole.

SLEEVES Sleeves are to be one { 1) piece, have a three quarter {3/4) inch hem and finish ten { I 0) inches long from the should seam.

BUTTONS There are to be nine (9) metal buttons and one { 1) 4-hole 21 ligne bone button to match, with two (2) extra buttons on shirt tail front. They shall be attached with a button sewing machine and sewn with best grade Poly-Cotton 60/36, 3 cord thread to match material. Front button spacing shall be three (3) inches below juncture of front pleat and collar and then three and one half (3 12/ ) inches for the remaining buttons.

PATCHES, INSIGNIA AND CHEVRONS Vendor to affix shoulder patches and chevrons to all garments where required. A ll shirts require two (2) shoulder patches. set %" from sleeve seam. Non- commissioned officers {Corporals, Sergeants and trooper first class) require chevrons on both sleeves of shirts, set one half { l/ 2) inch below shoulder patch.

STITCHING Shall be doubled stitched throughout using best grade Poly-Cotton 60/36, 3 cord threads to match material. Emblems and insignia shall be sewn with single needle. Sleeves to be set with two (2) needle flat-bed felling machines. Side seams must be felled on an off the arm double needle chain stitch felling machine. Safety serge, sleeve setting and side seaming construction is not acceptable. Women's shirts will be made with the same double needle construction as men's.

LABELS & NAME TAGS Garment must have linen identification name tag sewn to the inside right front tail. {Left front for female style facing option) .This linen tag is to include the complete measurements of the individual, along with the date of manufacture and the serial number. A permanent indelible ink must be used.

MEASUREMENTS All shirts shall be made to individual measurements and shall conform to measurements taken by Manufacturers agent. It is the intent of the Department to receive shirts guaranteed to fit each individual. Uniforms -State Police Specifications (A-F)

MILITARY CREASES Military creases to be sewn in. three (3) creases in back, two (2) in front. Front creases are to extend thru the pockets.

PRESSING All shirts shall be pressed. The sleeve is to be pressed from bottom of shoulder insignia to hem of sleeve. Uniforms - State Police Specifications (A-F)

SPECIFICATION B NEW HAMPSHIRE STATE POLICE LONG SLEEVE WINTER SHIRT RAEFORD MlLLS, ITEM #573-590 GENDER : MALE AND FEMALE

MATERIAL Raeford Mills style #573-590. 1 1- 1 1 12/ oz. 3-ply tropical weave. 553 Dacron/Polyester, 453 Wool. Dark green color. Shoulder straps and pocket flaps to be piped with style 573-437. Taupe color.

STYLE Modified Military Officers style with piped shoulder straps and pocket flaps.

FRONT Seven (7) button front including collar button. Left front to have a self-fabric center pleat one and one half ( 1 1/2) inch wide extending from collar bond to bottom of shirt. It shall have two (2) rows of double stitching with inside stitching seven eighths ( 7/8) inch apart. The center pleat to be interlined with poly-cotton VIKING PRESS canvas. Right front to hove on approximate two (2) inch turn bock to create a self-fly seven-eighths ( 7/8) inch wide. This self-fly will serve as a metal button guard. Right front to be edge-stitched one sixteenth ( 1/1 6} . Right front self-fly will have one ( 1 ) one quarter ( 1/4} inch buttonhole spaced approximately three (3) inches from neckband.

ZIPPER FRONT OPTIONAL Placket front with a fifteen inch (15) brass zipper (nylon is not acceptable) . The zipper is to be functional. The front shall contain four (4) non-functional buttons and buttonholes along with three (3) functional buttons and buttonholes. One ( 1) collar button, first and bottom buttons ore functional. Front placket to be finished with four (4) rows of stitching same as conventional front.

BADGE TAB Badge tab to be made of self-cloth two and one quarter (2¼ ) inches long and one (1) inch wide, with two (2) black metal eyelets set one and one quarter (1¼ ) inch apart. Badge tab to be set one ( 1 ) inch above left pocket flap.

BACK Straight yoke to finish three ( 3) inches below collar seam. Yoke is to be lines with matching 70 denier nylon taffeta.

COLLAR Dress collar with neckband. Fastened with a single button. Collar and neckband to be interlined with poly-cotton VIKING PRESS canvas. Plastic collar stays are to be sewn in so as not to show stitching on outside of collar. Neckband to be lined with matching 70 denier nylon taffeta and finished with three (3) rows of stitching on inner collar neckband. Collars to be made on single needle machine and top collar double stitched. Collar opening shall be three quarter (3/4) inch and allow room for the tie. Collar points to finish three (3) inches.

POCKETS

There shall be two (2) plain patch pockets approximately five and one quarter (5 ¼/. ) inch by six (6) inch deep, not including the flap. Pockets to have a top stitched pen and pencil opening of one and one half (1 ½) inch on right side of pocket. The lower corners of pockets ore to be mitered. Uniforms - State Police Specifications (A-F)

POCKET FLAPS There shall be two (2) scalloped flaps of self-material with one eighth (1/8) inch taupe piping, Raeford 571-437. Pocket flaps to sewn and turned, then top stitched on edge. Left flap to have one and one half (1 ½ ) inch opening at top for pencil on right side of flap. Pocket flaps to be placed approximately seven ( 7) inches down from shoulder seam. This seven (7) inches to vary according to size of shirt. Pocket flaps to be sewn down on each side of pocket to prevent access to pocket. The pocket flaps shall contain one ( 1) non-functional metal button centered.

SHOULDER STRAP To measure two (2) inches wide at sleeve head and extend to within approximately one quarter ( l/4) inch of collar. Shoulder straps to be sewn, turned and top stitched with one ( l) row of stitching. Straps are to be piped with contrasting taupe fabric. Straps to be set into each sleeve head when the sleeves are joined. Straps to be securely cross-stitched for a distance of approximately two and one half (2 ½) inches from the sleeve head and to contain one ( l) buttonhole set one half ( l/2) inch from pointed end. Shirts are to be made to accommodate a metal button on the shoulder strap. A one quarter ( l/4) inch buttonhole to be placed in the shirt to accommodate a metal button with a metal button guard made of one ( l) inch black tape set into collar seam and extending approximately one half ( l/2) inch beyond buttonhole.

SLEE VE S AND CUFF Sleeves are to be made one ( 1) piece with vent opening measuring approximately four (4) inches from top of cuff. Each sleeve to have a separate placket elbow reinforcement. semi banjo shape two (2) inches wide at vent opening and extending up the sleeve approximately eleven and one half ( 11 ½ ) inches, curving to the back of sleeve seam and set into seam. At this point the reinforcement should measure five and one half (5 ½) inch long and double stitched around. The button side facing of vent to finish one half ( l/2) inch in sleeve vent. Sleeve setting and closing shall be done with a two (2) needle felling machine. Cuff to be three (3) inch wide and made to accommodate two (2) metal buttons and double stitched. Metal buttons to be set in one quarter ( l/4) inch buttonhole with tape button guard.

BUTTONS There are to be thirteen ( 13) metal buttons and four ( 4) 4-hole 21 ligne bone button to match, with two (2) extra buttons on shirt tail front. They shall be attached with a button sewing machine and sewn with best grade Poly-Cotton 60/36, 3 cord threads to match material. Front button spacing shall be three (3) inches below juncture of front pleat and neckband and then three and one half (3 ½ ) inches for remaining buttons.

PATCHE S INSIGNIA AND CHEVRON Vendor to affix shoulder patches and chevrons on all garments where required. All shirts require two (2) shoulder patches, set 3/c" from sleeve seam. Non-commissioned officers (Corporals, Sergeants and trooper first class) require chevrons on both sleeves of shirts, set one half ( 1/2) inch below shoulder patch.

STITCHING Shall be doubled stitched throughout using best grade Poly-Cotton 60/36, 3 cord thread to match material. Emblems and insignia shall be sewn with single needle. Sleeves to be set with two (2) needle flat-bed felling machine. Side seams must be felled on an off the arm double needle chain stitch felling machine. Safety serge, sleeve setting and side seaming construction is not acceptable. Women 's shirts will be made with the same double needle construction as men's. Uniforms - State Police Specifications (A-F)

LABELS AND NAMETAGS Garment must have linen identification name tag sewn to the inside right front tail. (Left front for female style facing option) This linen tag is to include the complete measurements of the individual, along with the date of manufacture and the serial number. A permanent indelible ink must be used.

MILITAR Y CREASES Military creases to be sewn in. Three (3) creases in back. two (2) in front.

PRESSING All shirts shall be pressed. The sleeve is to be pressed from bottom of shoulder insignia to top of cuff.

SLEEVE LENGTH Actual sleeve length based upon individuals arm length and sleeve length desired, in not more than one half ( 1/2) inch units.

COLLAR Actual neck measurement according to individuals request in not more than one half (1/2) inch units.

CUFF SIZE To be proportioned to an individual's size.

Uniforms - State Police Specifications (A-F)

SPECIFICATION C NEW HAMPSHIRE STATE POLICE SUMMER WEIGHT TROUSERS RAEFORD STYLE, ITEM #573-437 NON COMMISSIONED OFFICER GENDER: MALE AND FEMALE

MATERIAL Raeford style 573-437, 1 1-1 1 12/ oz., 553 Dacron/Polyester, 453 Wool. 3-ply tropical. Taupe Color. The cloth shall be stamped with Kaumagraph stamp identifying the mill.

STYLE Men's slack type trouser . Modified Military Dress, cut from up to date men's trouser patterns. Trousers to have a one (1) inch outlet running the full length of inseam.

WAISTBAND Separate waistband to be two (2) inches wide (self-material) to be sewn to the waistband curtain with a Zig-Zag Ro-Cap stitch. Inside waistband curtain to be constructed from 653 Polyester, 353 Cotton Twill with Snug-Tex and one (1) inch Ban-Roi. Waistband to be finished in an open manner (Browne outlet method) for ease in alteration, showing no raw edges or merging on curtain edges and to finish with a minimum two and one half (2 1h) inch outlet. To close in front with one (1) crush proof Hook-Flex fastener. Right fly lining and crotch piece lining to be of same material as waistband curtain.

BELT LOOPS A minimum of seven (7) tunnel belt loops with additional loops in proportion to waist size. Each loop to be one ( 1) inch wide by two (2) inches long. One ( 1) loop to be placed at the rear seam with the other loops being proportionately spaced in back, on hips, and in front. All loops with the exception of the back loop are to be sewn into top of waistband and bottom of waistband. The back center belt loop to be sewn to the outside waistband.

POCKETS Two (2) front, two (2) hip and two (2) utility pockets. All pockets must be stitched, turned, and top stitched (serge edges not acceptable). Pocket material to be 7.4 oz. 72 x 60 all cotton drill natural shade. All pocketing to be inserted into waistband curtain. Pockets to be firmly bartacked at each end of pocket.

FRONT POCKETS Side pocket style, six and one half ( 6 1h) inches at the opening and six and one half (6 1/2) inches deep at bottom opening.

HIP POCKETS Hip pockets to be located a minimum of three (3} inches below bottom of waistband and to be a minimum of five and one half (5 ½ ) inches wide and a maximum of six (6) inches deep. Hip pockets to be made on a Reece pocket machine model # 46 Lock stitch with 3/16" double piping.

UTILIT Y POCKETS Utility Pockets to be located a minimum of three (3) inches below hip pocket and to be a minimum of three and one half (3 ½ ) inches wide at the opening and ten (10) inches deep. Utility pocket to be made on Reece pocket machine model # 46 Lock stitch with 3/16" double piping.

Uniforms - State Police Specifications (A-F)

STRIPE Trousers to have a one and one quarter (1 ¼/. ) inch wide stripe of Raeford style #573-590, 553 Dacron/Polyester, 453 Wool, 1 1-1 1 .5 oz. Dark green color. Stripe to be set to the front panel and set in to side seam from the bottom of waistband to the bottom of hem.

FLY Trouser shall be closed with a Talon Brass Flip Lock Zipper and have a brass bottom stop at the base of the zipper chain. A straight bartack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. Right fly to have a separate french fly tab with buttonhole and button to attach to waistband curtain.

BOTTOM HEM Trouser to have a plain bottom with no less than two and one half (2 ½ ) inch hem for adjustment. Deliveries may be accepted with unhemmed bottoms with inseam length of no less than 38".

STITCHING Trouser stitching with no less than twelve ( 12) stitches per inch. All seat seams to be double chain stitched with tandem needle machine. Side seam and inseam to be single needle chain stitch. This is to insure seam that will not separate. The entire trouser is to be sewn with Polyester core or 1003 Polyester spun Tex-40 thread.

LABEL AND NAMETAG Each garment shall have a linen label with individuals name, exact measurement, date of manufacture and other pertinent data. Label to be sewn on all four (4) sides and placed on right front pocket.

FINISHING AND PRESSING All loose threads shall be removed. Trouser must be pressed completely and properly with side seam, inseam and seat seam pressed open. Uniforms -State Police Specifications (A-F)

SPECIFICATION D NEW HAMPSHIRE STATE POLICE WINTER WEIGHT TROUSERS RAEFORD STYLE, ITEM #645-437 NON COMMISSIONED OFFICER GENDER : MALE AND FEMALE

MATERIAL Raeford style 645-437, 16 12/ -17 oz., 553 Dacron/Polyester,453 Wool. 2-ply elastique. Taupe color. The cloth shall be stamped with Kaumagraph stamp identifying the mill.

STY LE Men's slack type trouser. Modified Military Dress, cut from up to date men's trouser patterns. Trousers to have a one ( 1 ) inch outlet running the full length of inseam.

WAISTBAND Separate waistband to be two (2) inches wide (self-material) to be sewn to the waistband curtain with Zig-Zag Ro-Cap stitch. Inside waistband curtain to be constructed from 653 Polyester,353 Cotton Twill with Snug-Tex and one ( 1) inch Ban-Roi. Waistband to be finished in an open manner (Browne outlet method) for ease in alteration, showing no ram edges or serging on curtain edges and to finish with a minimum two and one half (2 ½ ) inch outlet. To close in front with one ( 1 ) crush proof Hook-Flex fastener. Right fly lining and crotch piece lining to be of same material as waistband curtain.

BELT LOOPS A minimum of seven (7) tunnel belt loops with additional loops in proportion to waist size. Each loop to be one ( 1 ) inch wide by two (2) inches long. One ( 1) loop to be placed at the rear seam with other loops being proportionately spaced in back, on the hips, and in front. All loops with the exception of the back loop are to be sewn into top of waistband and bottom of waistband. The back center belt loop to be sewn to the outside waistband.

POCKETS Two (2) front, two (2) hip and two (2) utility pockets. All pockets must be stitched, turned and top stitched (serge edges not acceptable) pocket material to be 7.4 oz. 72 x 60 all cotton drill natural shade. All pocketing to be inserted into waistband curtain. Pockets to be firmly bartacked at each end of pocket.

FRONT POCKETS Side pocket style, six and one half (6 ½) inches at the opening and six and one half (6 ½) deep at bottom opening.

HIP POCKETS Hip pockets to be located a minimum of three (3) inches below bottom of waistband and to be a minimum of five and one half (5 ½) inches wide and a maximum of six (6) inches deep. Hip pockets to be made on a Reece pocket machine model # 46 Lock stitch with 3/16" double piping.

UTILITY POCKETS Utility Pockets to be located a minimum of three (3) inches below hip pocket and to be a minimum of three and one half (3 ½) inches wide at opening and ten (10) inches deep. Utility pocket to be made on Reece pocket machine model # 46 Lock stitch with 3/ 16" double piping.

Uniforms - State Police Specifications (A-F)

STRIPE 1 Trousers to have a one and one quarter ( 1 /.) inch wide stripe of Raeford style #645-590, 553 Dacron/Polyester, 453 Wool, 16.5-17 oz. Dark green color. Stripe to be set to the front panel and set in to side seam from the bottom of waistband to the bottom of hem.

FLY Trouser shall be closed with a Talon Brass Flip Lock Zipper and have a brass bottom stop at the base of the zipper chain. A straight bartack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. Right fly to have a separate French fly tab with buttonhole and button to attach to waistband curtain.

BOTTOM HEM Trouser to have a plain bottom with no less than two and one half (2 12/ ) inch hem for adjustment. Deliveries may be accepted with unhemmed bottoms with inseam length of no less than 38".

STITCHING Trouser stitching with no less than twelve ( 1 2) stitches per inch. All seat seams to be double chain stitched with tandem needle machine. Side seam and inseam to be single needle chain stitch. This is to insure seam will not separate. The entire trouser is to be sewn with Polyester core of 1003 Polyester spun Tex-40 thread.

LABEL AND NAMETAG Each garment shall have a linen label with individual name, exact measurement, date of manufacture and other pertinent data. Label to be sewn on all four (4) sides and placed on right front pocket.

SPECIFICAT ION E NEW HAMPSHIRE STATE POLICE SUMMER WEIGHT TROUSERS RAEFORD STYLE, ITEM #573-437 COMMISSIONED OFFICER GENDER : MALE AND FEMALE

MATERIAL Raeford style 573-437, 1 1-1 1 Y2 oz.,553 Dacron/Polyester, 453 Wool, 3-ply tropical, Taupe color. The cloth shall be stamped with Kaumagraph stamp identifying the mill.

STYLE Men's slack type trouser. Modified Military Dress, cut from up to date men's trouser patterns. Trousers to have a one ( 1) inch outlet running the full length of inseam.

WAISTBAND Separate waistband to be two (2) inches wide (self-material) to be sewn to the waistband curtain with Zig-Zag Ro-Cap stitch. Inside waistband curtain to be constructed from 653 Polyester, 353 Cotton Twill with Snug-Tex and one ( 1) inch Ban-Roi. Waistband to be finished in an open manner (Browne outlet method) for ease in alteration, showing no raw edges or serging on curtain edges and to finish with a minimum two and one half ( 2 ½) inch outlet. To close in front with one (1) crush proof Hook-Flex fastener. Right fly lining and crotch piece lining to be of same material as waistband curtain.

BELT LOOPS A minimum of seven ( 7) tunnel belt loops with additional loops in proportion to waist size. Each loop to be one ( 1) inch wide by two (2) inches long. One ( 1 ) loop to be placed at the rear seam with other loops being proportionately spaced in back, on the hips, and in front. All loops with the exception of the back loop are to sewn into top of waistband and bottom of waistband. The back center belt loop to be sewn to the outside waistband.

POCKETS Two (2) front, two (2) hip and two (2) utility pockets. All pockets must be stitched, turned and top stitched (serge edges not acceptable) . Pocket material to be 7.4 oz. 72 x 60 all cotton drill natural shade. All pocketing to be inserted into waistband curtain. Pockets to be firmly bartacked at each end of pocket.

FRONT POCKETS Side pocket style, six and one half (6 V2) inches at the opening and six and one half ( 6 V2) inches deep at bottom opening.

Uniforms - State Police Specifications (A-F)

STRIPE Total width to be one and one quarter (1 ¼ ) inch with inside width to be three quarter (3/4) inch. Inside material to be Raeford style 573-437, 553 Dacron/Polyester. 453 Wool, 1 1- 1 1 .5 oz.. taupe color. Outside material to be Raeford style 573-590,553 Dacron/Polyester,453 Wool, dark green color, one quarter (1/4) inch each side. Both stripes are to be top stitched from the bottom of the waistband over side pocket and taper to center over the side seam.

FLY Trouser shall be closed with a Talon Brass Flip Lock Zipper and have a brass bottom stop at the base of the zipper chain. A straight bartack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. Right fly to have a separate French fly tab with buttonhole and button to attach to waistband curtain.

BOTTOM HEM Trouser to have a plain bottom with no less than two and one half (2 ½ ) inch hem for adjustment. Deliveries may be accepted with unhemmed bottoms with inseam length of no less than 38".

STITCHING Trouser stitching with no less than twelve (12) stitches per inch. All seat seams to be double chain stitched with tandem needle machine. Side seam and inseam to be single needle chain stitch. This is to insure seam that will not separate. The entire trouser is to be sewn with Polyester core or 1003 Polyester spun Tex-40 thread.

LABEL AND NAMETAG Each garment shall have a linen label with individual name s. exact measurement, date of manufacture and other pertinent data. Label to be sewn on all four (4) sides and placed on right front pocket.

SPECIFICATION F NEW HAMPSHIRE STATE POLICE WINTER WEIGHT TROUSERS RAEFORD STYLE, ITEM #645-437 COMMISSIONED OFFICER GENDER: MALE AND FEMALE

MATERIAL Raeford style 645-437, 16 1/2-1 7oz.,553 Dacron/Polyester, 453 Wool, 2-ply elastique. Taupe Color. The cloth shall be stamped with Kaumagraph stamp identifying the mill.

STYLE Men's slack type trouser. Modified Military Dress, cut from up to date men' s trouser patterns. Trousers to have a one (1) inch outlet running the full length of inseam.

WAISTBAND Separate waistband to be two (2) inches wide (self-material) to be sewn to the waistband curtain with a Zig-Zag Ro-Cap stitch. Inside waistband curtain to be constructed from 653 Polyester, 353 Cotton Twill and Snug-Tex and one ( 1) inch Ban-Roi. Waistband to be finished in an open manner (Browne outlet method) for ease in alteration, showing no raw edges or serging on curtain edges and to finish with a minimum two and one half (2 ½ ) inch outlet. To close in front with one (1) crush proof Hook-Flex fastener. Right fly lining and crotch piece lining to be of same material as waistband curtain.

BELT LOOPS A minimum of seven ( 7) tunnel belt loops with additional loops in proportion to waist size. Each loop to be one (1) inch wide by two (2) inches long. One (1) loop to be placed at the rear seam with the other loops being proportionately spaced in back, on the hips and in front. All loops with the exception of the back loop are to be sewn into top of waistband and bottom of waistband. The back center belt loop to be sewn to the outside waistband.

POCKETS Two ( 2) front, two (2) hip and two (2) utility pockets. All pockets must be stitched, turned and top stitched (serge edges not acceptable). Pocket material to be 7.4 oz. 72 x 60 all cotton drill natural shade. All pocketing to be inserted into waistband curtain. Pockets to be firmly bartacked at each end of pocket.

FRONT POCKETS Side pocket style, six and one half (6 ½ ) inches at the opening and six and one half (6 ½ ) inches deep at button opening.

HIP POCKETS Hip pockets to be located a minimum of three (3) inches below bottom of waistband and to be a minimum of five and one half (5 ½)inches wide and a minimum of six (6) inches deep. Hip pockets to be made on a Reece pocket machine model # 46 Lock stitch with 3/l 6" double piping. Hip pockets to contain a pointed flap, self-lined with buttonhole and button.

UTILITY POCKETS Utility Pockets to be located a minimum of three (3) inches below hip pocket and to be a minimum of three and one half (3 ½) inches wide eat the opening and ten (10) inches deep. Utility pocket to be made on Reece Pocket Machine model #46 lock stitch with 3/16” double piping.

Uniforms - State Police Specifications (A-F)

STRIPE Total width to be one and one quarter (1 ¼ ) inch with inside width to be three quarter (3/ 4) inch. Inside material to be Raeford style 645-437, 553 Dacron/Polyester, 453 Wool, 16.5- 17 oz., Taupe color. Outside material to be Raeford style 645-590, 553 Dacron/Polyester, 453 Wool, dark green color, one quarter (1/4) inch each side. Both stripes are to be top stitched from the bottom of the waistband over side pocket and taper to center over the side seam.

FLY Trouser shall be closed with a Talon Brass Flip Lock Zipper and have a brass bottom stop at the base of the zipper chain. A straight bartack shall be sewn through from the outside of the garment to the inside at the bottom of the fly. Right fly to have a separate French fly tab with buttonhole and button to attach to waistband curtain.

BOTTOM HEM Trouser to have a plain bottom with no less than two and one half (2 ½ ) inch hem for adjustment. Deliveries may be accepted with unhemmed bottoms with inseam length of no less than 38".

STITCHING Trouser stitching with no less than twelve (12) stitches per inch. All seat seams to be double chain stitched with tandem needle machine. Side seam and inseam to be single needle chain stitch. This is to insure seam that will not separate. The entire trouser is to be sewn with Polyester core or 100% Polyester spun Tex-40 thread.

LABEL AND NAMETAG Each garment shall have a linen label with individual names, exact measurement, date of manufacture and other pertinent data. Label to be sewn on all four (4) sides and placed on right front pocket.

FINISHING AND PRESSING All loose threads shall be removed. Trouser must be pressed completely and properly with side seam, inseam and seat seam pressed open.

MATERIAL Raeford Mills style #573-590. 1 1 - 1 1 12/ oz. 3-ply tropical weave. 553 Dacron/Polyester, 453 Wool. Dark green color. Shoulder straps and pocket flaps to be piped with style 573-437. Taupe color.

STYLE Modified Military Officers style with piped shoulder straps and pocket flaps.

FRONT Seven (7) button front including collar button. Left front to have a self-fabric center pleat one and one half (1 ½ ) inch wide extending from collar band to bottom of shirt. It shall have two (2) rows of double stitching with inside stitching seven eighths ( 7/8) inch apart. The center pleat to be interlined with poly-cotton VIKING PRESS canvas. Right front to have an approximate two (2) inch turn back to create a self-fly seven-eighths (7/8) inch wide. This self-fly will serve as a metal button guard. Right front to be edge-stitched one sixteenth ( 1/16). Right front self-fly will have one (1) one quarter (1/4) inch buttonhole spaced approximately three (3) inches from neckband.

ZIPPER FRONT OPTIONAL Placket front with a fifteen inch ( 15) brass zipper (nylon is not acceptable) .The zipper is to be functional. The front shall contain four (4) non-functional buttons and buttonholes along with three (3) functional buttons and buttonholes. One ( l) collar button, first and bottom buttons are functional. Front placket to be finished with four (4) rows of stitching same as conventional front.

- • • - ... .. #

Uniforms - State Police Specifications (A-F)

BADGE TAB Badge tab to be made of self-cloth two and one quarter (2¼) /inches long and one (1 ) inch wide, with two (2) black metal eyelets set one and one quarter (1 ¼ ) inch apart./. Badge tab to be set one (1) inch above left pocket flap.

BACK Straight yoke to finish three (3) inches below collar seam. Yoke is to be lined with matching 70 denier nylon taffeta.

COLLAR Dress collar with neckband. Fastened with a single button. Collar and neckband to be interlined with poly-cotton VIKING PRESS canvas. Plastic collar stays are to be sewn in so as not to show stitching on outside of collar. Neckband to be lined with matching 70 denier nylon taffeta and finished with three (3) rows of stitching on inner collar neckband. Collars to be mode on single needle machine and top collar double stitched. Collar opening shall be three quarter (3/4) inch and allow room for the tie. Collar points to finish three (3) inches.

POCKETS 1 There shall be two (2) plain patch pockets approximately five and one quarter (5 ) /.i nch by six (6) inch deep, not including the flap. Pockets to have a top stitched pen and pencil opening of one and one half ( 1 V2) inch on right side of pocket. The lower corners of pockets are to be mitered.

POCKET FLAPS There shall be two (2) scalloped flaps of self-material with one eighth ( 1/8) inch taupe piping, Raeford 571-437. Pocket flaps to sewn and turned, then top stitched on edge. Left flap to have one and one half (1 ½ ) inch opening at top for pencil on right side of flap. Pocket flaps to be placed approximately seven (7) inches down from shoulder seam. This seven (7) inches to vary according to size of shirt. Pocket flaps to be sewn down on each side of pocket to prevent access to pocket. The pocket flaps shall contain one (1) non-functional metal button centered.

SHOULDER STRAP To measure two (2) inches wide at sleeve head and extend to within approximately one quarter (1/4)inch of collar. Shoulder straps to be sewn, turned and top stitched with one ( 1) row of stitching. Straps are to be piped with contrasting taupe fabric. Straps to be set into each sleeve head when the sleeves are joined. Straps to be securely cross-stitched for a distance of approximately two and one half (2 ½ ) inches from the sleeve head and to contain one ( 1 ) buttonhole set one half (1/2) inch from pointed end. Shirts are to be made to accommodate a metal button on the shoulder strap. A one quarter ( 1/4) inch buttonhole to be placed in the shirt to accommodate a metal button with a metal button guard made of one (1 ) inch black tape set into collar seam and extending approximately one half (1/2) inch beyond buttonhole.

SLEEVES AND CUFF Sleeves are to be made one ( 1) piece with vent opening measuring approximately four (4) inches from top of cuff. Each sleeve to have a separate placket elbow reinforcement, semi banjo shape two (2) inches wide at vent opening and extending up the sleeve approximately eleven and one half (1 ½ ) inches, curving to the back of sleeve seam and set into seam. At this point the reinforcement should measure five and one half (5 ½ )inch long and double stitched around. The button side facing of vent to finish one half (1/2) inch in sleeve vent. Sleeve setting and closing shall be done with a two (2) needle felling machine. Cuff to be three (3) inch wide and made to accommodate two (2) metal buttons and double stitched. Metal buttons to be set in one quarter ( 1/4) inch buttonhole with tape button guard.

Uniforms – State Police Specifications (A-F)

BUTTONS There are to be thirteen (13) metal buttons and four (4) 4-hole 21 ligne bone button to match. with two (2) extra buttons on shirt tail front. They shall be attached with a button sewing machine and sewn with best grade Poly-Cotton 60/36, 3 cord thread to match material. Front button spacing shall be three (3) inches below juncture of front pleat and neckband and then three and one half (3 ½ ) inches for remaining buttons.

PATCHES INSIGNIA AND CHEV RON Vendor to affix shoulder patches and chevrons on all garments where required. All shirts require two (2) shoulder patches, set ¾ “ from sleeve seam. Non-commissioned officers (Corporals, Sergeants and trooper first class) require chevrons on both sleeves of shirts, set one half ( ½) inch below shoulder patch.

STITCHING Shall be double-stitched throughout using best grade Poly-Cotton 60/36, 3 cord thread to match material. Emblems and insignia shall be sewn with single needle. Sleeves to be set with two (2) needle flat-bed felling machine. Side seams must be felled on an off the arm double needle chain stitch felling machine. Safety serge, sleeve setting and side seaming construction is not acceptable. Women's shirts will be made with the same double needle construction as men' s.

LABELS AND NAME TAGS Garment must have linen identification name tag sewn to the inside right front tail. (Left front for female style facing option) This linen tag is to include the complete measurements of the individual, along with the date of manufacture and the serial number. A permanent indelible ink must be used.

MILITARY CREASES Military creases to be sewn in. Three (3) creases in back, two (2) in front.

PRESSING All shirts shall be pressed. The sleeve is to be pressed from bottom of shoulder insignia to top of cuff.

SLEEVE LENGTH Actual sleeve length based upon individuals arm length and sleeve length desired, in not more than one half (1/2) inch units.

COLLAR Actual neck measurement according to individuals request in not more than one half (1/2) inch units.

CUFF SIZE To be proportioned to an individual's size. Uniforms - Corrections Specifications

SP,ECIFICATION G NEW HAMPSHIRE CORRECTIONS LONG SLEEVE SHIRTS FLYING CROSS BY FECHHEIMER, ITEM #35W5435 GENDER: MALE AND FEMALE

FABRIC:

Content: 653 Dacron Polyester I 353 Combed Cotton

Weight: 4.0 to 4.25 oz. I square yard

COLOR Navy Blue

FABRIC FEATURE StainSmart® effectively repels spills and releases oily and ground-in stains while machine washing. This treatment will last for the life of the garment. Fabric has 8-123 Stretch.

STYLE To be Flying Cross Model 35W5435. Dress style, top center placket front. full cut tapered fit. banded collar, long sleeves with barrel cuffs, and dress shirttail. Two pleated breast pockets with topstitched scalloped flaps. Topstitched shoulder straps. Full badge reinforcement. Back to have a double yoke of shirting material. Work wear industrial style shirt construction is unacceptable and shall be cause for rejection.

FRONT The left front shall have a top center placket 1-1/2" wide with two rows of stitches 7/8" apart. The shirt will have 7 buttons and buttonholes on the front; spacing between each will be 3 ¾" except the spacing between the neck button and the first button on the front, which will be approximately 3 ¼“. Top center placket to have woven interlining of #250 Dacron. Non-woven interlining unacceptable and shall be cause for rejection. The fronts shall be joined to the yoke so that both raw edges of the yoke are turned under, with the front sandwiched between, and then all three are stitched down with a 1/16" raised stitch. Safety stitch joining unacceptable. •·';

Uniforms - Corrections Specifications

SHOULDER STR APS Shoulder straps to be two-piece pointed, 1/8" topstitched and to be set on yoke with leading topstitch conforming with front joining seam. To measure 2" at sleeve tapering to 1 3/8” and set not more than 1/2" from collar set seam. Cross-stitched approximately 2" from sleeve seam. Shoulder strap to have functional buttonhole to attach to sewn button on shoulder of shirt. Edge stitched shoulder strap construction unacceptable.

BADGE REINFORCEMENT Two-ply sling 1" wide centered over left pocket and stitched to shoulder seam and flap setting stitch. It shall have 2 (two) buttonhole eyelets 1 ¼“ from top of pocket flap spaced 1 ¼" apart and centered on sling.

POCKETS Two breast patch pockets with mitered corners and 1 ¼“ stitched pleats. Pleats shall be stitched top and bottom and full length of length of pleat to prevent spreading. Pocket to measure 5 5/8” wide, 6” deep. Left Breast pocket to have 1½“ pencil stitch. Each pocket to have hook Velcro, ¾ “ long by ½ “ wide, positioned on both edges of pocket to correspond with outer scalloped flap points as specified. Velcro to be stitched all sides and to be sewn through pocket and shirt for added reinforcement.

Uniforms - Corrections Specifications

FLAPS Two piece deep scalloped design to measure 5 7/8” across and 2 3/4" in depth at center point, 2 ¼” at sides. Secured to shirtfront approximately 3/8" above pocket. Left flap to have invisible pencil opening 1½” to correspond precisely with pencil slot of pocket (Stop & start stitching for pencil opening unacceptable shall be cause for rejection.) Flaps to be 1/8 “topstitched. Flap to have woven interlining of #250 Dacron. Creased and edge stitched pocket flap construction unacceptable. Underside of the flap to have looped Velcro 3/4" long by 1/2" wide stitched all sides, positioned on outer points of both pocket flaps to secure with corresponding Velcro strips on shirt pocket. Each flap shall have a button centered on uncut sewn buttonhole.

SLEEVES Sleeve vent shall be a minimum of 4-1 /2" long with one-piece top and bottom facings. Facing to measure 1-1/8" wide point blocked at top.

CUFFS Two piece ½” hemmed cuff with 1/8” topstitching. CUFF INTERLINING Cuffs to measure 2 ½“ in depth with rounded corners (barrel cuffs) . Cuffs to have two buttons and corresponding buttonholes set vertically with one button and buttonhole in center of facing. Cuffs to have woven interlining of #250 Dacron.

BUTTONS First grade 19-ligne pearlescent to match.

SEWING Collar, shoulder straps, pocket flaps and cuffs to be topstitched 1/8” off the edge. Sleeve inserting and side close felling seams are to be safety stitched.

THREAD All sewing threads to be color fast polyester wrap to match.

INTERLININGS Collar, cuffs, pocket flaps and top center to be interlined with #250 Dacron. Collar band interlining to be Crease N Tack.

Uniforms - Corrections Specifications ·

MILITARY CREASES: There shall be five stitched-in sharp military creases on all shirts. One crease on each front to be centered vertically. Front creases shall be through pockets and flaps. Spacing for three military creases across shirt back to be proportionate to the size of the shirt.

CONSTRUCTION Collars, flaps, shoulder straps, and cuffs are made with conventional construction. Top ply bottom ply and interlining are first stitched together, then turned right side out and finally topstitched.

STOCK SIZES

Shirts must be available in the following sizes: Sleeve lengths: 32-37 inches Neck sizes: 14-1 /2 to 18-1/2, 19, 20, 21, 22

SPECIFICATION H

NEW HAMPSHIRE CORRECTIONS

EMBROIDERED TACTICAL POLO

General

• Snag proof, odor fighting • 6.6 ox polyester • Double-needle stitched throughout • Tag free labels • Flat knit collar • 3-button placket with dyed to match buttons • Mic Clips at center placket and shoulders • Raglan sleeves • Drop tail to stay tucked in Uniforms - Corrections Specifications

SPECIFICATION I NEW HAMPSHIRE CORRECTIONS DUTY JACKET B. DRYI ITEM #6120 GENDER: MALE AND FEMALE

GENERAL All garment details not specifically described herein; tailoring, styling, construction, materials, and components must match the standard reference sample on file with the agency. Written specifications attempt to describe key requirements of a 3D garment and cannot do so adequately and therefore silence of the specifications does not absolve bidders from matching with precision the standard reference sample.

Pre-bid samples will be required at the time of the bid opening. Samples may be subjected to laboratory testing at the discretion of the contracting officer. Bidders are responsible for all testing costs of their sample garments.

Bidders must enclose evidence (dated manufacturers catalogs or similar) that this item is currently a commercial in-stock style. The successful bidder will provide a full size run of try -on garments within 10 days for agency approval.

Garments must be manufactured to ISO 9001 quality assurance standard. A copy of the certificate registration will be required with the bid.

Specification based on Size Medium, Regular length.

FABRIC 3.4oz per square yard Taslanized nylon. Warp 70 Denier and filling 2 ply 70 Denier. Back coated with a honeycomb printed breathable pattern for durability. Water repellant treated face with soil release properties.

LINING Permanent Lining Fabric: B. Dry 1 .85 oz. per square yard 100% nylon 70 denier ripstop with a total count of 210. Color: charcoal or black. Fabric shall be coated or laminated with a waterproof breathable polymer that can be washed and dry cleaned, and seam sealed. Fabric shall be 3,000 MM waterproofness (test method # JIS-L1092A) and 3,000 grams/M2/per 24 hours breathability (test method # JIS-L1099A).

INSULATION Removable Insulated Liner: 6 inch diamond pattern quilted insulation package. 1.85 oz. per square yard, 100% Nylon 70 denier rip stop woven face fabric (Color: charcoal} . Thermolite Plus or B. Warm BSCL-120 insulation for sleeves and BSCL-120 for body. 1 .8 oz. per square yard, 100% Nylon 70 denier plain weave taffeta backing fabric (Color: black) . Fiber migration resistant construction and treatment with no added layers of scrim. Machine washable/dryable, dry cleanable, and can be pressed. Shrinkage less than 2%.

½“ long from shoulder seam.

BUTIONS

SEWING

THREAD

INTERLINING f

CONSTRUCTION Collars, f laps and shoulder straps are made with conventional construction. Top ply, bottom ply and interlining are first stitched together, then turned right side out and finally topstitched.

STOCK SIZES

Shirts must be available in the following sizes : Neck sizes: 14-1/2 to 18-1/2, 19, 20, 21, 22 Uniforms - Corrections Specifications

SEAM TAPE Waterproof seam sealing tape compatible with the permanent waterproof-breathable lining. (Color: Clear)

TRIM Pocketing: 65% polyester 35% Cotton. (Color: black). Brushed Pocketing: 100% polyester tricot. (Color: black) Interlining: 100% polyester non-woven. Binding: 100% Nylon Taffeta. Knit: 100% polyester in a 1 " X 1" rib knit. (Color: match the shell fabric.) . Ribbon Loops: ½" grosgrain. (Color: black) . Snaps: 20 ligne spring snaps with closed backs, gunmetal finish on brass, heavy-duty closure, 24 ligne nylon cap (Color: Black). Hook and Loop: woven nylon base. (Color: black) . Eyelets: aluminum. (Color: black) Metal Uniform Buttons: 24 ligne nickel "P" buttons unless specified by agency.

ZIPPERS Zippers: Front zipper: delrin, one-way, size #5, 26". Sleeve underarm zippers: nylon coil, one way, size #3, 10". Inside pocket zipper: nylon coil, one-way zipper, size #3, 5.5 inches. Liner zipper: delrin, one-way, size #3, 46". Removable sleeve liner zippers: delrin, one-way, size #3, 16". Side vent zippers: nylon coil, one-way, size #5, 9.5". (Zipper lengths specified are for size L/Reg, Color: black

COLLAR AND STAND There shall be a sport style collar with zipper extending to the top. The collar and defined collar stand shall be made of two layers of shell fabric and one of non-woven interlining. The collar and stand will lay flat and be shaped to the neck without gapping or puckering. When turn up the collar will comfortably fit around the wearer 's neck and come short of the chin. There shall be a 1" by ½“hanger loop attached to the back of the collar and a garment label on the inside collar.

SLEEVES Sleeves are to be shaped two-piece style. The cuffs to be 2" in width, half elastic and half not, and to fasten with a 2' x 1 .5" hook and loop tab. The cuff shall be topstitched 1/4" at the bottom. Cuffs are to be interlined with non-woven and elastic to retain its shape. Cuff opening (size Large) shall be 5" folded. Each sleeve shall have a 10" underarmed zipper #3 coil to allow access to the shell for emblems and other customization. The zipper tapes shall be set in besom style so the teeth are covered.

FRONTS Jacket fronts shall be well one-piece, shaped, and symmetrical (balanced). There shall be a separate interlined straight bottom hem which shall measure 2 ¼“ There shall be a #5 Delrin nylon one-way zipper with a compatible colored tape sewn to the fronts of the jacket for closure. Zipper tape and teeth shall be covered by a ¼" facing with interlining to prevent fabric from catching in zipper. Zipper shall have attached pull for ease of handling with gloves.

SI DE OPE NINGS There shall be side openings on both sides for access to equipment. The zippered opening will be 9.5" long and use a Delrin #5 coil zipper opening from bottom to top. There shall be a snap tab with male Prym style snap and cap measuring 3.5" relaxed and 4.5 " stretched and Prym style snaps female snaps and caps on each side of the zipper for closure and storage of the snap tab. The tab will hold front and rear portions of the jacket closed around equipment when the zipper is in the up position. Uniforms - Corrections Specifications

POCKETS AND FLAPS To have two (2) lower two-way opening patch pockets, topstitched 1/16" from the edge, with mitered corners, to finish 7 ¼“ wide and 7 ¼“ long. The left pocket shall have a pencil compartment 1 ¼” wide. Both pockets shall have an inverted pleat and a hand warmer opening in back lined with fleece. The flaps shall be interlined and pointed style and shall measure 3 ¼“ at the point and 7 ½“ wide. There shall be a stitched eyelet hole for placement of a uniform style metal button just above the point. The flaps shall close to the pocket by means of two mini-gripper snaps at the corners of the flaps to prevent them from curling.

BADGE TAB There shall be a badge tab made from a strip of shell material 1" wide and 2" long with metal grommets spaced 1 3/8" center to center. It shall be stitched and folded, so that there are no raw edges.

SHOULDER STRAPS The shoulder straps shall be topstitched ¼" from the edge and be pointed at the end toward the neck of the jacket where both points shall be tacked. The other end shall be sewn in the sleeve and taper to 2 ¼“ wide. The length is to be graduated conforming to the size of the jacket. The strap shall be box and cross-stitched to the shoulder approximately 1 ¾ “ from the sleeve head seam, leaving enough room for a detachable mic to feed through it. There shall be a stitched eyelet hole near the pointed end for fastening of a uniform metal button using a cotter pin.

BACK The back shall be one piece with an elasticized 2 ¼“ hem bottom hem the entire length of the back made from a folded layer of shell fabric and a layer of dry cleanable elastic.

REMOVABLE LINER There will be a quilted liner with zip-off sleeves for versatile all-season wear. The liner will be fully removable by means of a 48" molded tooth count plastic zipper. The liner shall attach to the sleeves by means of a snap tab and loop set to the jacket permanent lining sleeve. The zipper shall be attached to an internal facing measuring 2 ¾“ around the liner. The sleeves of the liner shall remove by means of a 15 inch #3 molded tooth count zipper leaving an insulated vest. There shall be a pass through on the liner to access the permanent lining inside pocket.

INSIDE POCKET There shall be a large zippered storage pocket attached to the permanent lining of the jack et on the left inside front. The pocket opening will be 5 ½“ wide and the pocket will be 8" deep. The pocket attachment seams shall be seam sealed.

PERMANENT LINING The permanent waterproof, windproof and breathable lining shall be seam sealed all around and shall be free hanging at the neck seam. It shall be attached to the facings, top of the collar and to the hem of the jacket only. Al! critical seams shall be sealed with thermoplastic sealing tape.

THREAD All thread shall be polyester wrapped on monofilament polyester. Color to match. '.J Uniforms - Corrections Specifications

STITCHING All stitching conforms to Federal Standard 751 specifications (FED-STD-751 ) . All stitch types are sewn at stitch per inch (S.P.I.) rates individually set by operation at no less than 10 S.P.I. and not more than 12 S.P.I. to insure extended sewn wear life. All thread tension is evenly maintained to eliminate right or loose stitching. All seam allowances are to be maintained so that there are no raw edges, run offs, twist, pleats, puckers or open seams.

SIZES Permanent size marking to be located inside of collar.

CARE LABEL Care instructions to be on inside pocket.

PRESSING & FINISHING Jacket shall be carefully pressed by hand in a first class manner. All loose threads to be thoroughly trimmed.

UNISEX SIZING Regular: XS - 6XL Tall: M - 6XL

MEASUREMENTS Regular length: Size: M

Chest: 49.5 (+/- 0.75 inches) Sleeve from CB Neck: 36 (+/- 0.5 inches) Back Length: 25.5 (+/- 0.5 inches)

Uniforms - Corrections Specifications ·

SPECIFICATION J

NEW HAMPSHIRE CORRECTIONS OUTER PARKA

B. DRY, ITEM #9860 GENDER : MALE AND FEMALE

GENERAL All garment details not specifically described herein; tailoring, styling, construct ion. materials. and components must match the standard reference sample on file with the agency. Written specifications attempt to describe key requirements of a 3D garment and cannot do so adequately and therefore silence of the specifications does not absolve bidders from matching with precision the standard reference sample.

Garments must be manufactured to ISO 900 I quality assurance standard. A copy of the certificate registration will be required with the bid.

Specification based on Size Medium, Regular length.

I ·'.I ·t r·-·---·...·-1 , ·----, o I \_ ... !' ;, r=··_.. 1 .'•, I I . •....l ,,, l , '

•• -· - - --- _! -

. I ·Uniforms - Corrections Specifications

FABRIC • 3.6oz per square yard Taslanized nylon. • Warp: 70 Denier • Filling: 2 ply 70 Denier. • Back coated with a honeycomb printed breathable pattern for durability. • Water repellant treated face with soil release properties.

LINING • Permanent Lining Fabric: B. Dry 1 .85 oz. per square yard • 100% nylon • 70 denier rip-stop with a total count of 210. • Color: charcoal or black. • Fabric shall be coated or laminated with a waterproof breathable polymer that can be washed and dry cleaned, and seam sealed. • Fabric shall be 3,000 MM waterproofness (test method # JIS-L1092A) and 3,000 grams/M2/per 24 hours breathability (test method # JIS-L 1099A).

S EAM TA PE Waterproof seam sealing tape compatible with the permanent waterproof-breathable lining unchanged after minimum 12 home laundry cycles. (Color: Clear)

TRIM • Eyelets: 8mm aluminum (Color: black) . • Hook and loop: durable woven nylon base (Color: black}. • Reflective trim: 1/2" wide heat-applied, silver crosswalk {collar & cuffs). • Snaps (must be Universal Fastener brand): o 15-ligne plastic style for draw-cord holder o 18-ligne prong style with closed backs, gunmetal finish on brass for pocket flaps o 24-ligne spring style with closed backs, on-rusting gunmetal finish on brass, heavy-duty closure for front storm-fly closure (Color: Black) . • Pocketing: 100% rip-stop lining (Color: black) . • Buttons: metal uniform 24-ligne chrome plated "P" with toggle & washers. • Ribbon loops using suitable width of grosgrain ribbon for pocket pulls and hem cord lock position (color: black). • Elastic cording with spring-closure cord lock for hem adjustments (color: black). • Zippers: o Front zipper: Delrin, two-way, double pull, size #5. o Liner zipper: Vision, One-way, Separat ing, MUSIzipper with double pull, size #5. o Sleeve underarm & Hood (collar) zippers: nylon coil, one way, size #3. o Side Vents: coil, two-way, double pull, size #5. (Color: black, YKK)

GENERAL DESIGN/ DESCRIPTION 2-layers 100% Nylon Tassah shell provides durability and maintains excellent appearance at all time. It is lightweight, breathable, quick dry with soft cotton feel. The 100% Nylon Ripstop Lining has 100% water-proof and breathable moisture wicking finish, adding warmth and perfect the fit. Detachable, Velcro on & off hood features elasticized draw-cord for cinch-in fit to keep wind out and can be stored away in collar zipper storage pocket. Double Storm flops protect zipper and keep wind and water from moving through and the adjustable cuffs and Draw-cord bottom hem seal in warmth. Other features include 2 concealed Napoleon pockets with Velcro closure, 4 outer pockets with flaps, build-in hand warmer under hip pockets and inner patch pocket for lining. Designed to zip together with optional zip-in insulted Liner jackets ,sold separately; or wear jacket alone as climate dictates.

Uniforms - Corrections Specifications (G-L)

COLLAR There shall be a sport style collar with zipper extending to the top with a 1/2" by 8" strip of above zipper opening. The collar shall be made of two layers of shell fabric and two layers of lining and has topstitching along outer edges to maintain waterproof integrity. Exposed zipper horizontal across back for storage of detachable hood shall measure 14" (for size L). The collar and stand will lay flat and be shaped to the neck without gapping or puckering and will comfortably fit around the wearer's neck and come short of the chin. There shall be a 2" by 3/8" hanger loop attached to the back of the collar and a garment label on the inside collar.

HOOD There shall be a detachable hood of 2-piece construction in shell material. unlined. There is an elastic draw cord with neoprene stops for hood opening and circumference adjustment. Hood width measures 23-3/4" and detaches using 5" s trip of hook/ loop tape to inside of collar zipper opening.

SLEEVE Sleeves are to be shaped two-piece style with partial elasticized back cuff measuring 1" W x 3 ¼“ Sleeves have a specialized rubber Velcro "hook" cuff tab that clean finishes into sleeve underarm seam on cuff matches to 1" W x 4" L "loop" on cuff for cuff adjustment. Cuff will hove three rows of single needle topstitching, evenly spaced thru' elasticized portion. A ½" wide heat-sealed "Crosswalk" reflective tape will be applied to the flat portion underside of each cuff for safety deployment. There shall be a 10" pit zipper opening at each sleeve underarm seam, 2" from armhole to provide easy access for the application of emblems on jacket.

FRONT Jacket fronts shall be well two-piece, shaped, and symmetrical (balanced) with top and under stormflies. Top and under stormflies constructed of 2 ply shell, 1 ply lining, and 1 ply interlining. Hidden female snaps set to top stormfly 1" from front edge (to center of snap). Male snaps set to bottom stormfly through all layers 1 3/8" from front edge (to center of snap) . Clean finish front zipper closure starts at l/2" below top edge of collar and ends 3" above hem. MUSI zipper for optional zip-in LINER, insert with zipper pull side on wearers left set behind triangle shaped 'neck guard' (garage) of self-fabric on both sides.

HEM Draw cord inserted into wearer's right side of bock panel and extends out wearer's left side of back panel. Two eyelets for draw cord thru are spaced 1" apart are set to the inside of hem on wearer's left side; placed 2" and 3" from side seam. Draw cord has cordlock for adjustment. Cordlock is held in place with loop of 1/4" grosgrain ribbon tape; excess elastic cording is held in place with grosgrain loop tab & 1-snap closure with finished measures 1/2" w x 2" L no stitching to be visible on outside of garment, stitched in place to inside lining. Stitching placement 2-1 /2" up from bottom edge. Hem shall measure 1 ".

SIDE OPENING There shall be side openings on both sides for access to equipment with two-way zippers to provide versatility. The zippered opening will be 11 ½“ long and use a coil #5 zipper opening from bottom to top with 'Railroad' construction. Uniforms - Corrections Specifications

POCKET AND FLAP Napoleon Pocket: Cut-away styling with 5/8'" W x 5" L Velcro "hook & loop" closure. Pocket opening to finished measures 8" W x 1 4" Deep. Grosgrain ribbon loop stitched to center of pocket opening to use as pull tab; tab measures 1" long.

Chest besom pocket: 1/4" double welt construction with opening concealed under flap on each side of front. Flap is constructed of 2-ply shell, 1-ply interlining with mitered corners, clean finished & stitch 1/2" above besom pocket with lI4" single needle stitch.

Hip patch pockets: Construction with 1 ¾“ double bend top hem and 2" wide inverted centered pleat. Shell fabric pocket backing & 1 pc DTM flannel create a 2nd pocket under the patch pocket, side entrance for "hand warmer". Flap constructed of 2-ply shell, 1-ply interlining with mitered corners, clean finished & stitched 3/4" above patch pocket with 1/4" single needle stitch; see AML for placement measures with grading.

Pen pocket: 1 ¼“ opening at inner corner of wearer's left hip pocket flap. (Inside) Lining Pocket: 1-ply self-patch pocket, 7" W x 8"L, edge-stitched to wearer's left front lining; has Velcro hook & loop tape closure, measures 5/8" W x 2" L centered at top edge of pocket: Placement: 13” down from Shoulder/Neck point & centered (between side seam and zipper)

BADGE TAB There shall be a badge tab made from 2 plies of shell fabric with 2 eyelets stitched vertically above wearers left chest pocket. Badge tab measures 7/8" wide and 2-1/2" long with 8mm size eyelets of metal material and should measure 1 3/8" from center to center.

NAME/MIC TAB Name tab made of 2 ply shell measuring 7/8" wide by 4" long. Tab shall be placed in polybag and swift-tacked to badge tab with Blauer hangtag.

EPAULET Epaulets shall be constructed of 2-ply shell fabric and 1-ply interlining with end shaping to a point. Sizing at Sleeve is 2-1/2"wide that tapers to the point at 2" wide. Placement should be centered to shoulder seam and top stitched with a 2" Box and "X" stitch thru' next to armhole seam with point ending placed 1 ¼“ from neckline; length grades as needed between sizes. "Keyhole" buttonhole with eyelet cut out at pointed end is to accommodate a uniform button that is secured using toggle & washer.

SIZE Permanent size marking giving size to be located inside of collar.

CARE LABEL Care instructions to be located behind size label.

PRESSING & FINISHING Jacket shall be carefully pressed by hand in a first class manner. All loose threads to be thoroughly trimmed.

UNISEX SIZING Short: Regular: Tall: XS - XL XS - 6XL M - 6XL

Uniforms - Corrections Specifications

MEASU R EMENTS Regular length: Size: M a. Chest: 51 I+/- 0.75 inches} b. Sweep: 49 (+/- 0.75 inches) c. Sleeve from CB Neck: 36 I+/- 0.5 inches) d. Bock Length: 32.5 (+/- 0.5 inches) Uniforms - Corrections Specifications

SPECIFICATION K NEW HAMPSHIRE CORRECTIONS POCKET TROUSER ITEM #881OX 6 GENDER : MALE AND FEMALE

Garments must be manufactured to ISO 9001 quality assurance standard. A copy of the certificate registration will be required with the bid.

Specification based on Men's Size 34, Regular length.

FABRIC Trousers shall be manufactured with the following fabric: • Blend: 653 Dacron Polyester, 353 combed cotton with 10% mechanical stretch • Weave: Twill • Weight: 6.7oz/yd. • Finish: Pre-cure permanent press with soil release finish Uniforms - Corrections Specifications

INTERNAL CONSTRUCTION FABRIC Pockets, waistband and fly lining shall be: • Blend: 65% Dacron Polyester,35% cotton • Weave: Twill • Weight: 5.2oz/yd. • Color: Dark Grey • Finish: Pre-cure permanent press

WAIST CLOSU RE Primary waist closure is a double hook and eye construction mounted on the waistband using rustproof nickel plated steel hardware as follows: Size 85 Eye and Eye internal reinforcement plate. Size 8 hook and hook internal reinforcement plate. Metal snaps which may become burred or crushed and cannot be replaced as unacceptable.

In addition to Hook and Eye plates, the construction includes the additional internal reinforcement of 7/8” tape mounted between the plates and the body fabric to insure cons truction integrity for extended wear life.

Waist closure appearance is further guaranteed by mounting a #22 ligne black four-hole button/buttonhole closure 1 " below the waistband on the left and right fly construction of fly tab.

SIDE FASTENER Slide fastener (fly zipper) consists of Delrin coil YKK hardware mounted on colorfast black blend nylon and cotton 7/16” tape, Coil size #5.

FLY CONSTRUCTION The right inside fly is reinforced with internal construction fabric and 1/8" gauge top stitched along the entire exposed edge to insure shape retention for extended wear life. The left, outside fly is fully lined internally for shape retention. Right and left fly are joined together at the base of the fly. The joined fly form a reinforcing tailpiece construction fully extending along the crotch seam to its intersection with leg inseams.

WAISTBAND Consists of left and a right plies of shell fabric, 1 layer of banroll, and 1 layer of rowcap for both sides. Rowcap applied to top of band creating a folded edge under the banroll. Banroll set to top inside edge to waist band with 0.062" top stitching gauge. The waist band joins at center back seam with approximately 1½“ seam allowance. There are also 2 metal hooks set to folded inside left front under band, placed 3/8" in from the folded edge and 1/2" apart with 2 metal eyes set to the right front band. Both hook and eyes should line up.

BELT LOOPS There are five (5) belt loops on trousers with waist 28-30",seven (7) on trousers with waist 31- 45", and 9 loops on waist sizes 46" and over. Each loop shall be fully 2¼“ long and 5/8" wide, double needle stitched and interlined with fusible. They shall be set into the waistband at the bottom and tacked at the top, except the rear center loop which shall be tacked top and bottom.

DARTS There are two darts to shape the trouser. They shall be placed at the left and right back extending down from the waistband to the center of each hip pocket. Uniforms - Corrections Specifications

CROTCH AND SEAT ASSEMBLY The crotch is formed below the fly at the intersection of the four body panels of the trousers. Left front, right front left rear and right rear. The trouser is assembled to form this crotch by first sewing the left front to the left rear thus making the left side of the trouser, and the right front to the right rear to form the rights side. The left side of the trouser thus formed is then joined together to the right side by means of the seat seam. The trouser is not assembled by the alternate whole front to whole back method due to the unreliability of that method during extended wear life.

S EAT CONSTRUCTION To insure absolute seat seam integrity, the seat seam, which joins the left and right sides of the trousers, is double sewn by means of two needles each sewing stitch type 401, double locked stitch. The two needles sew in tandem to form closely adjacent alternating stitches totaling not less than 16 per inch. Seams, which expose thread to external abrasion, are unacceptable.

Extra fabric is allowed such that seat girth and waistband diameter may be expanded or decreased by the wearer during the trousers extended wear life. Flat felled seams do not allow for alteration and are unacceptable.

CROTCH REINFORCEMENT The crotch intersection, which is the core of the trouser, shall be reinforced to absorb extreme stress over an extended wear life by the internal mounting of a reinforcement gusset formed by an extension of the tail of the fly. This gusset is mounted around its perimeter by stitch 301 such that it locks together the four panels of the trouser to absolutely eliminate any potential for crotch seam failure.

LEG CONSTRUCTION The legs are fully cut for ease of movement and assembled using stitch 515, four-thread safety stitch and also lock stitching creating a split seam construction allowing tapering of the inseam. There shall also be left and right let outs at the thigh for alteration in which the waist fits correctly but the thigh is too tight for the wearer.

POCKETS There are six (6) pockets assembled from internal construction fabric as follows:

I. Front: Left and right 6½“ quarter top style opening with 11¼“ depth. Opening to be bar-tack reinforced at top inside waistband and at bottom across side seam. Construction includes a second reinforcing layer or "Heel" at the bottom of each pocket not less than 2" deep. Pockets, including reinforcement "Heels" are assembled using an overedge stitch, then turned and re-stitched by stitch 301 for absolute reliability for the life of the trouser.

II. Rear: Left and right besom type hip pockets with bottom welt construction openings 5 ¾ “ wide and 6" deep. Openings triangle bar-tack reinforced at both ends. Both pocket openings include a tab and # 22 Ligne black four hole buttonhole to close the pocket.

Ill. Side: Left and right mitered cargo pockets with pocket flap and zipper closure. Cargo pockets have crosswalk reflective trim, cell phone pocket on the outside and elasticized pockets inside. Cargo pockets. measure 7½“ wide by 8½“ long. Uniforms - Corrections Specifications

THREAD All thread shall be polyester wrapped on monofilament polyester. Color to match.

STITCHING All stitching conforms to Federal Standard 751 specifications ( FED-STD-751) . All stitch types are sewn at stitch per inch (S.P.1.) rates individually set by operation at no less than l0 S.P.I. and not more than 12 S.P.I. to insure extended sewn wear life. Stitch type 401 Tandem is used at a combined S.P.I. of 16. All thread tension 1s evenly maintained to eliminate right or loose stitching, All seam allowances are to be maintained so that there are no raw edges, run offs twist, pleats, puckers or open seams.

FINISHING Trousers are fully shaped on high temperature, high-pressure presses to eliminate wrinkles and form creases. Trousers meet the standard of the American Association of Textile Chemists and Colorists as follows:

I. AATCC Test Method 124-1975 "Appearance of Durable Press Fabric After R epeated Home Launderings". II. AATCC Test Method 888-1975 "Appearance of Seams in Wash and Wear Items After Home Launderings". Ill. AATCC Test method 88C-1975 "Appearance of Crease in Wash and Wear Items After Home Launderings".

WORKMANSHIP All trousers are made in an ISO 9000 certified plant and are inspected during manufactur ing, at final trimming and packing to insure consistent quality and adherence to this specification.

WARRANTY All trousers shall be warranted against defects in materials and workmanship for one year.

LABELING All trousers will bear all labels mandated by the Federal Trade Commission at the date of manufacture. All products must be cut and sewn in Mexico using US made components.

SIZING Trousers are fully graded such that all vital dimensions change according to waist size. The grade applies not only to seat, front rise, back rise, and thigh measurements but also to the knee and bottom measurements. Additionally, the trousers shall be manufactured and stocked in three (3) separate rises, regular, long and short rise, each with their own grade designed to fit regular, long and short torsos.

STANDARD SIZE RANGE Men's: Regular Length: even waist sizes 28 - 54; odd sizes 31 - 37 Women's: Regular Length: even dress sizes 6 - 24 Uniforms - Corrections Specifications

MEASUREMENTS Men's: • Regular Length: Waist Size 34 • 1/2 Waist: 17.5 (+ 0.25 inch) • Seat: 22.5 (+ 0.25 inch) • 1/2 Knee: 14.25 (+ 0.25 inch) • 1/2 Bottom Leg: 9 (+ 0.25 inch) • Inseam: 37 (+ 0.50 inch) • Front Rise: 10 (+ 0.25 inch) • Back Rise: 15.5 (+ 0.25 inch)

Women' s: • Regular Length: Dress Size 12 • 1/2 Waist (Relaxed) : 17.5 (+ 0.25 inches) • 1/2 Waist (Stretched) : 18.5 (+0.25 inches) • Seat: 22.25 (+/- 0.25 inches) • 1/2 Knee: l0.312 (+/- 0.25 inches) • 1/2 Bottom Leg: 8.875 (+/- 0.25 inches) • Inseam: 35.75 (+/- 0.50 inches) • Front Rise: 9.125 (+/- 0.25 inches) • Back Rise: 13.5 (+/- 0.25 inches)

SPECIFICATION L

NEW HAMPSHIRE CORRECTIONS

1/4 ZIP SWEATSHIRT

GENERAL

• Durable, colorfast quarter zip feature • Minimal shrinkage • 2x2 rib knit cuffs and waistband with spandex • 9-ounce, 65/35 ring spun combed cotton/poly fleece • Twill-taped neck