DIY: Home Project Ideas Using Simpson Strong-Tie® RTC2Z Rigid

Home , Workbench (woodworking)

Home Project Ideas Using Simpson Strong-Tie® RTC2Z Rigid Tie® Connectors

Table of Contents

Heavy-Duty Workbench ��2

Heavy-Duty Shelving Unit ��4

Work Table ��6

Outdoor Storage Center ��8

Over-Car Garage Shelving Unit ��10

Log Holder ��12

Outdoor Potting Bench ��14

Chicken Coop ��16

BUILD-IT-YOURSELF INSTRUCTIONS

TM Heavy-Duty Workbench Building this 4'-wide workbench is fast and easy with 2x4 lumber and Simpson Strong-Tie® Rigid Tie® RTC2Z connectors. Create a sturdy workbench to act as a storage center and workstation. It’s ideal for the garage or basement and can be built in different lengths to accommodate your needs.

Check out our installation and building tip videos at diydoneright.com. TOOLS YOU NEED • Saw • Screw gun PEGBOARD • #2 Phillips head bit • Tape measure • Clamps • Framing square 2x4 BOARDS Rigid Tie RTC2Z connectors are easy to install and strong enough to support even the heaviest boxes, tools or machinery, and can be

5 finished with paint to blend with ⁄8" PLYWOOD TOP AND SHELF the style of your home.

RIGID TIE RTC2Z CONNECTOR INSTALLATION INSTRUCTIONS

1. CUT LUMBER AND PLYWOOD TO SIZE Since all of your cuts are straight cuts, Simpson Strong-Tie connectors simplify building with wood.

2. INSTALL CONNECTORS ON VERTICAL POSTS Mark height, clamp connector to post and attach with Simpson Strong-Tie #8 x 1¼" wafer-head Cut notches in shelf screws. No corners to fit around predrilling is 2x4 corner posts. needed. Top needs only the back corners notched. Bottom shelf needs all four corners notched. 3. CONNECT HORIZONTAL RAILS ON EACH SIDE Use a clamp to help hold the wood in the seat Install RTC2Z top connectors of the connector approximately 1½" below top of post. during installation.

4. NOTCH CORNERS OF Attach Rigid Tie RTC2Z with PLYWOOD SHELVES #8 x 1¼" wafer-head screws. Use a piece of 2x4 on each corner of the shelf, trace and cut to accommodate corner posts (only notch back corners of top shelf).

MATERIALS AND CUTTING DIAGRAM

TM 2' x 4' Heavy-Duty Workbench

FRONT VIEW TOP RAIL SIDE VIEW

REAR CORNER POST

58" RAIL END RAIL

FRONT CORNER 28⅜" POST 36"

45" 48" 17" 24"

FOR THIS PROJECT, YOU WILL NEED: LUMBER SIMPSON STRONG-TIE® CONNECTORS FASTENERS (6) – pieces of 2x4 x 8' lumber (8) – Rigid Tie® RTC2Z connectors (1) – BOX Simpson Strong-Tie #8 x 1¼" wafer-head screws 5 (1) – 4' x 4' sheet of ⁄8" plywood (20) – #6 x 1¼" bugle-head screws (1) – 2' x 4' sheet of ¼" pegboard (4) – #6 x 2½" bugle-head screws

CUT FROM 2x4 x 8' LUMBER

(4) – 45" RAILS 45" 45" (2x)

(2) – 58" REAR CORNER POSTS & (2x) (4) – 17" ENDRAILS 58" 17" 17"

(1) – 48" TOP RAIL 48" (1x)

(2) – 36" FRONT CORNER POSTS 36" 36" (1x)

CUT FROM PLYWOOD AND PEGBOARD (1) – TOP/BOTTOM SHELF 5 24" x 48" ⁄8" plywood 24" x 48" Top Shelf Cut both shelves from (Notch back corners only) 5 (1) 4' x 4' sheet of ⁄8" plywood. Attach with #6 x 1¼" flat-head screws...... (1) – 24" x 48" PEGBOARD 24" x 48" Bottom Shelf ...... PEGBOARD (Notch all corners) ...... 24" x 48" Attach with #8 x 1¼" wafer-head screws......

The construction plan for this project is designed to be completed by people with basic carpentry skills in standard situations. If your situation is unique, talk with someone with detailed carpentry or construction experience before starting your project. Particular attention was paid to the steps and details in this plan, but they cannot be guaranteed to be error free. Simpson Strong-Tie shall not be responsible for any possible loss, damage (800) 999-5099 or injury resulting directly or indirectly from the information contained here. strongtie.com © 2017 Simpson Strong-Tie Company Inc. • P.O. Box 10789, Pleasanton, CA 94588 DIY-CSWRKBCH17 8/17 exp. 12/21

For more inspiration, visit diydoneright.com

BUILD-IT-YOURSELF INSTRUCTIONS

TM Heavy-Duty Shelving Unit Building this 4'-wide shelving unit is fast and easy with 2x4 lumber and Simpson Strong-Tie® Rigid Tie® RTC2Z connectors. Create an organized, sturdy shelf unit that is ideal for the garage or basement. It can be built in different lengths to accommodate your needs, and is strong enough to hold the heaviest boxes or tools.

TOOLS YOU NEED Check out our installation and building tip videos at www.diydoneright.com. • Saw • Screw gun • #2 Phillips head bit • Tape measure • Clamps Install Rigid Tie RTC2Z top connectors • Framing square approximately 1½" below Rigid Tie RTC2Z connectors are top of post. easy to install and strong enough to support even the heaviest boxes, tools or machinery, and can be

5⁄8" PLYWOOD TOP finished with paint to blend with the style of your home.

RIGID TIE RTC2Z CONNECTOR INSTALLATION INSTRUCTIONS

1. CUT LUMBER AND PLYWOOD TO SIZE Since all of your cuts are straight 2x4 LUMBER cuts, Simpson Strong-Tie connectors simplify building with wood.

2. INSTALL CONNECTORS ON VERTICAL POSTS

5⁄8" PLYWOOD Mark height, clamp connector to post SHELVES and attach with Simpson Strong-Tie #8 x 1¼" wafer-head screws. No predrilling is needed.

3. CONNECT HORIZONTAL RAILS ON EACH SIDE Cut notches in all Use a clamp to four shelf corners to fit around 2x4 corner posts. help hold the wood in the seat of the connector during installation.

4. NOTCH CORNERS OF PLYWOOD SHELVES Use a piece of 2x4 on each corner of the shelf, trace and cut to accommodate corner posts (do not notch Attach Rigid Tie RTC2Z top shelf). with #8 x 1¼" wafer-head screws.

TM 2' x 4' x 6' Heavy-Duty Shelving Unit

FRONT VIEW SIDE VIEW

48" 24"

17⅝" 21½"

45"

RAIL

17⅝" 21½" 72"

END RAIL FRONT CORNER 17⅝" ½ POST 21 "

6" 17"

FOR THIS PROJECT, YOU WILL NEED: LUMBER SIMPSON STRONG-TIE® CONNECTORS FASTENERS (9) – pieces of 2x4 x 8' lumber (16) – Rigid Tie® RTC2Z connectors (2) – BOXES Simpson Strong-Tie #8 x 1¼" wafer-head screws (1) – 4' x 8' sheet of 5⁄8" plywood (40) – #6 x 1¼" bugle-head screws

CUT FROM 2x4 x 8' LUMBER (8) – 45" RAILS 45" 45" (4x)

(4) – 72" CORNER POSTS & 72" 17" (4x) 17" END RAILS

(8) – 17" END RAILS 17" 17" 17" 17" (1x)

CUT FROM PLYWOOD 96"

(1) – 24" x 48" TOP SHELF

24" x 48" Top Shelf 24" x 48" Lower Shelf (Notch all corners) (3) – 24" x 48" LOWER SHELVES 48" Cut top and 3 shelves from 5 (1) 4' x 8' sheet of ⁄8" plywood. 24" x 48" Lower Shelf 24" x 48" Lower Shelf Attach with #6 x 1¼" flat-head screws. (Notch all corners) (Notch all corners)

The construction plan for this project is designed to be completed by people with basic carpentry skills in standard situations. If your situation is unique, talk with someone with detailed carpentry or construction experience before starting your project. Particular attention was paid to the steps (800) 999-5099 and details in this plan, but they cannot be guaranteed to be error free. Simpson Strong-Tie shall not be responsible for any possible loss, damage or injury resulting directly or indirectly from the information contained here. strongtie.com © 2017 Simpson Strong-Tie Company Inc. • P.O. Box 10789, Pleasanton, CA 94588 DIY-CSHDSHLF17 8/17 exp. 12/21

For more inspiration, visit diydoneright.com

A FAST WAY TO CREATE A NEW WORK SPACE

TM Work Table Whether you are looking to add work space to your home or college dorm room, building this 4 ft. work table is a breeze with 2x2 lumber and Simpson Strong-Tie® connectors. Create the perfect table to fit your space, customized to fit your needs. Build it in different lengths and widths, and even add more shelves for added storage. Once it’s done, get creative with paint to add some flair.

Check out our installation and building tip videos at diydoneright.com. TOOLS YOU NEED • Saw • Screw gun • #2 Phillips head bit 5⁄8" PLYWOOD TOP AND SHELF • Tape measure • Clamps • Framing square Connectors are easy to install and 2x2 LUMBER strong enough to support even the heaviest boxes, tools or machinery, and can be finished with paint to blend with the style of your home.

5⁄8" PLYWOOD/OSB SHELVES RIGID TIE® RTC22Z CONNECTOR INSTALLATION INSTRUCTIONS

1. CUT LUMBER AND PLYWOOD TO SIZE. Since all of your cuts are straight cuts, Simpson Strong-Tie® connectors simplify building with wood.

2. INSTALL CONNECTOR ON VERTICAL POST. Mark height, clamp connector to post Cut notches in all and attach with Simpson Strong-Tie® four shelf corners to #8x1¼" fit around 2x2 corner post Wafer-Head screws. No pre-drilling is Install RTC22 needed. connectors flush with top of corner post Attach Rigid Tie® RTC22Z 3. CONNECT HORIZONTAL connectors with #8x1¼" RAIL ON EACH SIDE. Wafer-Head screws Use a clamp to help hold the wood in the seat of the connector during installation.

4. NOTCH CORNERS OF Need a heavy-duty PLYWOOD SHELVES. work table that’s ideal for your Use a piece of 2x2 on each corner of garage or basement? the shelf, trace and cut to Build the perfect work table that can accommodate stand up to the most demanding needs. corner posts. Visit www.strongtie.com/diydoneright for plans to build a 2 ft. x 4 ft. table using 2x4 lumber and Rigid Tie® RTC2Z connectors.

MATERIALS AND CUTTING DIAGRAM

TM 2 ft. x 4 ft. Work Table

FRONT VIEW SIDE VIEW

END RAIL RAIL

CORNER 26¾" POST

36"

7½" 6"

45" 21"

48" 24"

FOR THIS PROJECT YOU WILL NEED: LUMBER SIMPSON STRONG-TIE® CONNECTORS FASTENERS (5) – pieces of 2x2 8 ft. lumber (8) – Rigid Tie® RTC22Z connectors (1) – BOX Simpson Strong-Tie® #8x1¼" Wafer-Head screws (1) – 4 ft. x 4 ft. sheet of 5⁄8" plywood (36) – #8x1¼" flat-head screws or 6d finish nails for a more finished surface

CUT FROM 2x2 x 8' LUMBER (4) – 45" RAILS 45" 45" (2x)

(4) – 36" CORNER POSTS 36" 36" (2x)

(4) – 21" END RAILS (1x)

CUT FROM PLYWOOD

24" x 48" Top Shelf (1) – 24" x 48" TOP SHELF

(1) – 24" x 48" LOWER SHELF 24" x 48" Lower Shelf (Notch all corners) Attach with #8x1¼" flat-head screws or 6d finish nails at 8" spacing

Note: For a more finished appearance you can explore various types of premium plywood (ie: Birch, Maple, etc.) or 1x lumber options.

For more inspiration, visit diydoneright.com A21 Angle ORGANIZE YOUR OUTDOOR TOOLS AND SUPPLIES

TM Outdoor Storage Center Need extra storage for your lawn mower or gardening tools and supplies? With Simpson Strong-Tie® connectors, it’s easy for you to get all of your outdoor goods organized. This sturdy storage center can be completed, from start to finish, in just one day.

Check out our installation and building tip videos at diydoneright.com. TOOLS YOU NEED • Saw A21 angle H2.5A tie TP35 tie plate H1 rafter tie A21 angle • Screw gun • #2 Phillips head bit • ¼" hex drive socket • Tape measure • Clamps • Framing square • Hammer • Straight edge

Connectors are easy to install and strong enough to support even the heaviest boxes, tools or machinery, and can be finished with paint to 5⁄8" PLYWOOD ROOF blend with the style of your home. A21 ANGLE RIGID TIE® RTC2Z CONNECTOR INSTALLATION INSTRUCTIONS

1. CUT LUMBER AND PLYWOOD TO SIZE. Since all of your cuts are straight cuts, Simpson Strong-Tie® connectors Install Rigid Tie® simplify building with wood. RTC2Z connectors ½" below top of post 2. INSTALL CONNECTOR 5 ⁄8" PLYWOOD ON VERTICAL POST. SHELF Mark height, clamp connector to post and attach with Simpson Strong-Tie® #9x1½" Strong-Drive® SD Connector screws. 2x4 LUMBER

3. CONNECT HORIZONTAL RAIL ON EACH SIDE. Use a clamp to help hold the wood in the seat of the connector during installation.

4. NOTCH CORNERS OF PLYWOOD SHELVES. Use a piece of 2x4 on each corner of the shelf, trace and cut to accommodate corner posts.

Rigid Tie® RTA2 connector FB24 bracket Rigid Tie® RTC2Z connector

MATERIALS AND CUTTING DIAGRAM

TM Outdoor Storage Center

FRONT VIEW SIDE VIEW 96" 46" 23¼" 24" 24" 23¼"

RAFTER BLOCKING RAFTER

93" 22½" LONG FRONT RAIL

VERTICAL

31½" 26" CORNER 92 5⁄8" LONG BACK RAIL POST 85"

41½" SHORT SIDE RAIL 60" FRONT 21¼" RAIL 36"

13" 10" 31" 11½"

FOR THIS PROJECT YOU WILL NEED: 38" LUMBER SIMPSON STRONG-TIE® CONNECTORS* FASTENERS (18) – pieces of 2x4 8 ft. lumber (14) – Rigid Tie® RTC2Z connectors (2) – H2.5A ties (5) – BOXES Simpson Strong-Tie® ® (1) – 4 ft. x 4 ft. sheet of 5⁄8" plywood (4) – TP35 tie plates (6) – H1 rafter ties #9x1½" Strong-Drive SD Connector screws (1) – 4 ft. x 8 ft. sheet of 5⁄8" plywood (6) – A21 angles (4) – RTA2Z connectors (48) – #8x1¼" flat-head screws (2) – FB24Z brackets CUT FROM 2x4 x 8' LUMBER (6) – 85" VERTICAL CORNER POSTS 85" (6x)

(1) – 96" LONG BACK RAFTER BLOCKING 96" (1x, no cut)

(2) – 93" LONG FRONT/BACK TOP RAIL 93" (2x)

(2) – 60" LONG BACK RAIL & 60" 31" (2x) 31" SIDE RAILS

1 1 1 (4) – 31 ⁄2" SHORT FRONT/BACK RAILS & 31 ⁄2" 31 ⁄2" 31" (2x) (2) – 31" SIDE RAILS

(5) – 31" SIDE RAILS 31" 31" 31" (2x) (Results in extra scrap rail)

(5) – 46" RAFTERS 46" 46" (3x) (Results in extra scrap rafter)

CUT FROM 4' x 8' PLYWOOD Use 2x4 x 8' preservative-treated (1) – 96" x 46" PLYWOOD ROOF 5⁄8" Exterior-Grade Plywood Roof lumber, or non-treated lumber with (2) – 38" x 33" SHELVES 38" x 33" 38" x 33" exterior-grade stain or paint. Dimensions Top Shelf Bottom Shelf can be modified to fit your specific needs. Cut roof and both shelves from (Notch all (Notch all Use roofing material of your choice. 5 corners) corners) (2) 4'x8' sheets of ⁄8" plywood. Underlayment and asphalt shingles are Attach with flat-head #8x1¼" screws recommended. Follow manufacturer’s at 8" spacing. instructions for installation.

*CORROSION INFORMATION: We recommend using our ZMAX® galvanized product for best results on exterior projects and those using preservative-treated wood. These products have a “Z” at the end of the model number (eg. RTC2Z). ZMAX® coated products provide additional corrosion resistance, which is advisable but not required, for non-structural projects like the one shown above. Visit www.strongtie.com/info for critical information.

For more inspiration, visit diydoneright.com

EXTRA STORAGE MADE EASY

TM Over-Car Garage Shelving Unit You can find extra storage on the back wall of your garage by using the space above your car’s hood. This simple, unique way of building a strong storage unit is fast and easy with 2x4 lumber and Simpson Strong-Tie® Rigid Tie® RTC2Z connectors. Custom size the width and depth to fit your particular storage needs and still have plenty of room for your vehicle.

Check out our installation and building tip videos at diydoneright.com. TOOLS YOU NEED • Saw • Screw gun 5 • #2 Phillips head bit ⁄8" PLYWOOD TOP RIGID TIE® RTC2Z AND SHELF CONNECTORS • Tape measure • Clamps • Framing square Connectors are easy to install and strong enough to support even the heaviest boxes, tools or machinery, and can be finished with paint to blend with the style of your home.

2x4 LUMBER RIGID TIE® RTC2Z CONNECTOR INSTALLATION INSTRUCTIONS

1. CUT LUMBER AND PLYWOOD TO SIZE. Since all of your cuts are straight cuts, Simpson Strong-Tie® connectors simplify building with wood.

2. INSTALL CONNECTOR ON VERTICAL POST. Mark height, clamp connector to post and attach with Simpson Strong-Tie® NOTE: lower framework #8x1¼" does not have a front Wafer-Head beam to allow for hood screws. No of car pre-drilling Cut notches in all 4 is needed. shelf corners of lower shelf to fit around Install Rigid Tie® RTC2Z 2x4 corner connectors ½" below top of post

3. CONNECT HORIZONTAL RAIL ON EACH SIDE. Attach Rigid Tie® Use a clamp to RTC2Z connectors help hold the with #8x1¼" wood in the seat Wafer-Head screws of the connector during installation.

4. NOTCH CORNERS OF PLYWOOD SHELVES. Use a piece of 2x4 on each corner of the shelf, trace and cut to RTA2Z Connector accommodate corner posts.

MATERIALS AND CUTTING DIAGRAM

TM 8 ft. x 2 ft. Over-Car Garage Shelving Unit

Note: Verify vehicle width and hood height before finalizing design.

SIDE VIEW FRONT VIEW 96" 24"

FRONT RAIL

341⁄2" FRONT CORNER POST

72"

END 25" RAIL Change this dimension 34" (floor to first front rail) as (shown) needed to accomodate your vehicle

12" 107⁄16"

93" 17"

FOR THIS PROJECT YOU WILL NEED: LUMBER SIMPSON STRONG-TIE® CONNECTORS FASTENERS (10) – pieces of 2x4 8 ft. lumber (10) – Rigid Tie® RTC2Z connectors (2) – BOXES Simpson Strong-Tie® #8x1¼" Wafer-Head screws 5 ® (1) – 4 ft. x 8 ft. sheet of ⁄8" plywood (2) – Rigid Tie RTA2Z connectors (60) – #6x1¼" flat-head screws

CUT FROM 2x4 x 8' LUMBER (5) – 93" RAILS 93" (5x)

(4) – 72" CORNER POSTS & 72" 17" (4x) 17" END RAILS

(2) – 17" END RAILS 17" 17" (1x)

CUT FROM 4' x 8' PLYWOOD

(1) – 24" x 96" TOP SHELF 24" x 96" Top Shelf

(1) – 24" x 96" LOWER SHELF 24" x 96" Lower Shelf Attach with #6x1¼" flat-head screws (Notch all corners)

For more inspiration, visit diydoneright.com

STACK LOGS NEAT AND CLEAN

TM Log Holder This sturdy log holder makes stacking easier and keeps your firewood organized and off the ground. Use 2x4 preservative-treated lumber with Simpson Strong-Tie® Rigid Tie® RTC2Z connectors to build this log holder any size you need in less than an hour.

Check out our installation and building tip videos at diydoneright.com. TOOLS YOU NEED • Saw • Screw gun • ¼" hex head socket • Tape measure • Clamps

2x4 LUMBER • Framing square Length can vary as needed Connectors are easy to install and strong enough to support even the heaviest loads.

RIGID TIE® RTC2Z CONNECTOR INSTALLATION INSTRUCTIONS

1. CUT LUMBER TO SIZE. Since all of your cuts are straight cuts, Simpson Strong-Tie® connectors simplify building with wood.

2. INSTALL CONNECTOR ON VERTICAL POST. Mark height, clamp connector to post and attach with #9x1½" Strong-Drive® SD Connector screws.

3. CONNECT HORIZONTAL RAIL 2x4 LUMBER ON EACH SIDE. Width and height can Use a clamp to vary as needed help hold the wood in the

® seat of the con- Attach Rigid Tie RTC2Z nector during connectors with #9x1½" SD Connector screws installation.

MATERIALS AND CUTTING DIAGRAM

TM Log Holder

FRONT VIEW SIDE VIEW

30"

47" 8" 50" 15"

FOR THIS PROJECT YOU WILL NEED: LUMBER SIMPSON STRONG-TIE® CONNECTORS* FASTENERS (3) – pieces of 2x4 8 ft. lumber (4) – Rigid Tie® RTC2Z connectors (1) – BOX Simpson Strong-Tie® #9x1½" Strong-Drive® SD Connector screws

CUT FROM 2x4 x 8' LUMBER

(2) – 47" RAILS 47" 47" (1x)

(3) – 30" CORNER POSTS 30" 30" 30" (1x)

(2) – 8" ENDRAILS & (1) 30" CORNER POST 30" 8" 8" (1x)

Use 2x4 8 ft. preservative-treated lumber or non-treated wood with exterior grade stain or paint. Dimensions can be modified to fit your specific needs.

*CORROSION INFORMATION: We recommend using our ZMAX® galvanized product for best results on exterior projects and those using preservative-treated wood. These products have a “Z” at the end of the model number (ex. RTC2Z). ZMAX® coated products provide additional corrosion resistance, which is advisable but not required, for non-structural projects like the one shown above. Visit www.strongtie.com/info for critical information.

For more inspiration, visit diydoneright.com CREATE A ONE-STOP SPOT FOR GARDENING

TM Outdoor Potting Bench Building your own 4 ft. wide potting bench that includes a soil bin for potting or re-potting plants is fast and easy with 2x4 lumber and Simpson Strong-Tie® Rigid Tie® RTC2Z connectors. Create this sturdy potting bench with cedar, redwood or preservative-treated wood with a wood stain for a natural look, or use non- treated lumber and protect and personalize it with your favorite paint color.

Check out our installation and building tip TOOLS YOU NEED INSTALLATION INSTRUCTIONS videos at diydoneright.com. • Saw 1. MEASURE AND CUT LUMBER. • Miter saw All of your lumber cuts are straight Top Rail • Drill/Screw gun cuts, which make it easy to install • #2 Philips head bit the RTC2Z corner connectors. Back Leg • Tape measure 2. INSTALL CONNECTORS ON • Framing square EACH VERTICAL LEG. Mark height, • Straight edge or chalk line clamp RTC2Z connector to leg and • Clamps attach with #9x11/2" Strong-Drive® • Staple gun SD Connector screws. • Bit holder (optional) 3. CONNECT SHORT AND LONG RAILS • Paint brush ON EACH SIDE, TOP AND BOTTOM. (for sealing or painting) Shelf Use a clamp to help hold the wood in the seat of the connector. 4. INSTALL CENTER SUPPORT BOARDS. On the bottom, measure 22" in from the inside left short rail 2" Deck-Drive® DSV Wood Screws and attach the center support board with a 2" Deck-Drive™ DSV Wood screw from the back. Toenail the front DSV screw into the inside of the front horizontal rail. On the top, measure 26" in from the inside of the left short rail and attach the support board the same as the bottom. Work Surface Planks 5. ATTACH TOP RAIL AND SHELF. Attach the top rail to the end posts Work Surface with 21/2" bugle-head screws. Front Plank Measure down 16" from the rail and attach shelf between vertical Front Leg posts with 11/2" screws. Lower 6. INSTALL TRIM AND SPLASH Shelf Planks BOARDS. Start at the bottom and attach trim board to the front and back long rails between the legs with 2" screws. Then, attach the splash-board on the back of the legs. On the top, install the remaining trim board between the back legs. Splashboard 7. INSTALL TOP AND BOTTOM PLANKS WITH DSV SCREWS. Short Trim Start at the bottom. Attach the three Rail Long Boards 48" planks to the short rails, leaving 1 a ⁄4" gap between each plank. For Rigid Tie® Rails the top work surface, attach the RTC2Z left 171/2" plank first to the short rail #9x11/2" SD and then attach the right-hand side 3 Connector screw planks, leaving a ⁄8" gap between each one. Next, attach the front work surface plank so that it’s flush with the left plank. The soil bin will fit inside the top opening. 8. INSTALL LATTICE. Use a clamp to hold the lattice in place on the back legs and attach with 2" screws. Attach a splashboard to the bottom of the lattice with a staple gun.

TM Outdoor Potting Bench (2 ft. x 4 ft.)

FRONT VIEW SIDE VIEW

16"

2" Deck-Drive™ DSV Wood screw

75½"

261⁄2"

Rigid Tie® RTC2Z Connectors

1 50 ⁄2" Overall 24" 243⁄4"

34"

#9x11⁄2" ® 10" Strong-Drive 73⁄4" SD Connector 45" 17" screw 48" 24"

FOR THIS PROJECT YOU WILL NEED: LUMBER* SIMPSON STRONG-TIE® CONNECTORS AND FASTENERS OTHER (7) – pieces of 2x4 8 ft. lumber (8) – Rigid Tie® RTC2Z connectors – Soil bin (271/2" x 193/4" x 6") (3) – pieces of 1x4 8 ft. lumber (1) – 100-qty box Simpson Strong-Tie® #9x11/2" Strong-Drive® SD – Exterior-grade paint or stain (1) – piece of 1x6 8 ft. lumber Connector screws for exterior use (Model No. SD9112R100) (optional) (3) – piece of 1x6 6 ft. lumber (1) – 1-lb. box Simpson Strong-Tie® #10x2" Deck-Drive™ DSV Wood screws (1) – 4 ft. x 8 ft. sheet of redwood lattice for exterior use (Model No. DSVT212R1LB) (4) – 21/2" bugle-head screws (included in WBSK kit) CUT FROM 2x4 x 8' LUMBER (4) – 45" LONG RAILS 45" 45" (2x)

(2) – 34" FRONT LEGS 34" 34" 21" (1) – 21" CENTER SUPPORT (TOP) (1) – 48" TOP RAIL 48" 45" (1) – 45" TOP SHELF SUPPORT (2) – 74" BACK LEGS 74" (2x)

(4) – 17" SHORT RAILS 17" 17" 17" 17" 21" (1) – 21" CENTER SUPPORT (BOTTOM) CUT FROM 1x4 x 8' LUMBER (3) – 45" TRIM BOARDS 45" 45" (2x) (1) – 45" WORK SURFACE SPLASHBOARD (1) – 48" LOWER SHELF SPLASHBOARD 48" 171/2" (1) – 171/2"WORK SURFACE PLANK (LEFT) CUT FROM 1x6 x 8' LUMBER (1) – 501/2"WORK SURFACE FRONT PLANK 501/2" 45" (1) – 45" TOP SHELF

CUT FROM 1x6 x 6' LUMBER (3) – 48" LOWER SHELF PLANKS 48" 211/2" (3x) (3) – 211/2"WORK SURFACE PLANKS (RIGHT)

CUT FROM 4'x8' SHEET (1) – 48" x 43" REDWOOD LATTICE

* Use cedar, redwood, preservative-treated wood or non-treated wood with exterior-grade paint or stain.

For more inspiration, visit diydoneright.com

Give Your Chickens Space and Comfort

TM Chicken Coop Provide the space your chickens need to be happy, healthy, comfortable and productive. This customizable coop, built with Simpson Strong-Tie® connectors and fasteners, provides roomy and secure housing for three large birds or numerous smaller ones.

Our guidelines provide a starting point Check out our installation and building tip videos at diydoneright.com. for a basic, functional design. Here are some tips that will help ensure installation goes smoothly and safely. • Assembly requires at least two people. • Customization of chicken coop dimensions and location of openings will affect the cut list and material list; plan ahead to ensure you have your materials before construction. • Use cordless tools, such as impact drivers and gas-powered nail guns, to speed up the building process. • Verify lumber cuts with field conditions to account for uneven ground, inconsistencies in the wood and other unanticipated variables. • Take a cross tape measurement of the posts before securing to help keep them square. Then temporarily brace vertical posts with scrap lumber and braces while you plumb the posts vertically. • Use the suggested clamps. By clamping, you free up hands for making the necessary adjustments. • Use screws rather than nails for bracing so you can make adjustments. Nails are appropriate for the siding and roofing. • Consider the desired height of the chicken coop when selecting your ramp. Having an extra ramp available is convenient when the ramp in use requires cleaning.

Give Your Chickens Space and Comfort

TM What You Will Need

(U)

(L)

(P)

(T) (P) (O) (N) (R) (N) (O) (M) (V) (P) (S) (P) (Q) (P) (P) (M)

Hutch

(E) (I) (I) (E) (I) (I)

(K)

(Z) (B) (D)

(J) (J) (F) (I) (C)

(F) (I)

(I) (G) (H)

(A) (B) (C) (D)

(H) (A)

(K)

Coop Frame

Give Your Chickens Space and Comfort

TM What You Will Need

SIDE VIEW FRONT VIEW 61½" (I)

≠ ≠ ≠ ≠

≠ ≠

≠ ≠ (E)

≠ ≠ ≠ ≠ ≠ ≠

≠ ≠

≠≠ ≠ ≠ ≠

≠ ≠ (K) ≠ ≠

≠ ≠

12" ≠ (U) ≠ (K) ≠ (I)

68½" 72"

(Q) (Z) (S) 26½" 27" (J) (J) 35"

(J) (J) (D) (B) 77"

≠ ≠ ≠ ≠

≠

≠ ≠

(I) ≠ 65° (G) 25" (C) (B) (B) 26½" 33"

≠ ≠

≠ (K) ≠

≠ ≠ ≠ ≠ ≠ ≠ ≠ ≠

≠ ≠

≠ ≠ ≠ ≠ ≠ ≠ ≠ ≠ (K) ≠ (H) ≠ 3½" (A)

48" 96"

FOR THIS PROJECT YOU WILL NEED: Coop Frame and Hutch Frame • Circular saw (optional: chop saw) • Power drill with Phillips bit and Torx bit 77" (B) • Pencil (x2) • Tape measure 73½" (C) • Speed square (x2) • Staple gun 72" (D) (x2) SIMPSON STRONG-TIE® CONNECTORS AND FASTENERS 68½" (J) (14) Rigid Tie® RTC22 connectors (x2) (16) Rigid Tie RTA2Z connectors 58½" (E) 33" (F) (4) Rigid Tie RTC2Z connectors (x2) ⅛ (4) A21 angle connectors 15° 50 " (L) 46" (N) ™ 2x2 x 8' (x2) (4) Deck-Drive DSV WOOD Screws (2 ½", DSVT212) 15° ® 45" (M) 45" (M) (4) boxes Simpson Strong-Tie Wafer-Head Screws (x1) (#8 x 1¼", SD8x1.25) (for Rigid Tie connectors) ⅛ ™ 33 " (O) 30" (G) 29½" (K) (1) box Deck-Drive DSV WOOD Screws (1 ⅝", DSVT158) (x2) 15° 30⅞" (P) 30⅞" (P) 30⅞" (P) (x2) LUMBER 45" (I) (21) pieces 2x2 x 8' (x3) (3) pieces 2x4 x 8' 45" (I) (1) piece 2x1 x 8' (x1) (1) piece 1x10 x 8' 93" (A) (8) pieces 3/8" x 3/8" x 3' (x2) (1) piece 4' x 8' x ½" plywood 2x4 x 8' 45" (H) 45" (H) (2) pieces 4' x 8' x ½" plywood siding panel (x1)

OTHER MATERIALS ⅜" 42½" (Z) 2x1 x 8' (x1) (5) Hinges (3) Slide locks Ramp 67⅜" NOTES: 1. It is recommended that water-resistant sheathing or a 1x10 x 8' (x1) water barrier be used.

2. It is recommended that water-resistant lumber such 9¼" 9¼" 9¼" (x7) as redwood or cedar is used. If you use pine, use a ⅜" x ⅜" x 3' water-resistant finish on the wood to extend the life 9¼" of the chicken coop. (x1)

Connectors For more inspiration, visit diydoneright.com © 2017 Simpson Strong-Tie Company Inc. DIY-CSCHICK17 Model Quantity Model Quantity • RTC22 14 • DSV212 4 • RTA2Z 16 • SD8x1.25 4 (Box) • RTC2Z 4 • Hinges 5 • A21 4 • Silde Lock 3

Give Your Chickens Space and Comfort

TM What You Will Need

INSTALLATION INSTRUCTIONS 1½" Hutch Sheathing • CUT LUMBER TO SIZE 1½" Since all of your cuts are straight cuts, Simpson Strong-Tie® connectors simplify building with wood. (See page 3 for cut details.) Plywood • ASSEMBLE COOP (x1) 4' x 8' x ½" 48" Assemble coop sidewall using pieces (A) through (V) (U) 37⅝" (G), RTC22, RTA2Z and RTC2Z connectors as shown. Repeat for other coop sidewall. Join coop walls using two cross pieces (H), seven cross pieces (I) and RTA2Z connectors. 33⅞" 60" • ASSEMBLE COOP DOOR Assemble coop door by attaching pieces (J) and (K) to four RTA2Z connectors as shown. • ASSEMBLE HUTCH FRAME Assemble hutch sidewall using pieces L, M, N, O, Plywood siding panel (4) DSV212 screws and RTC2Z connectors. Repeat (x1) for second hutch sidewall. Join sidewalls using six 4' x 8' x ½" (R) (Q) cross pieces (P) and A21. 33⅞" 34¼" • ATTACH HUTCH SHEATHING Cut hutch floor (V) and roof (U) from ½" plywood. Cut hutch sloped sides (T, S) from siding. Cut hutch 36⅛" 47∕" square sides (Q, R) from siding. Attach hutch floor (V) to hutch frame using DSVT158 screws. Using 36⅛" 36⅛" the same screws, attach sloped sides (T, S) to hutch frame. Attach square side (Q) using hinges to hutch 12" frame. Attach square sides (R) to hutch frame. 10" Attach roof (U) to hutch frame. Add any preferred Plywood siding panel (T) (S) roofing material (corrugated material, shingles, 4' x 8' x ½" (x1) cedar shake, etc.) at this point, if desired. 48⅜" 15° • ADD CHICKEN WIRE Roll chicken wire out over doorframe and staple around entire perimeter. Cut chicken wire to fit. 47⅞" 47⅞" Roll chicken wire over coop frame using the same process, being careful not to cover the door bay and spots where the hutch will sit. • FINAL ASSEMBLY With a helper, set the completed hutch on the coop frame. Open hutch side door (Q) and, from the inside, use DSVT158 screws to attach door to coop frame. Attach completed door frame to door bay on coop frame using hinges. Attach preferred hardware to both hutch side door and coop door for fastening and locking. Add venting to hutch depending on your needs and local climate.

The construction plan for this project is designed to be completed by people with basic carpentry skills in standard situations. If your situation is unique, talk with someone with detailed carpentry or construction experience before starting your project. Particular attention was paid to the steps and details in this plan, but they cannot be guaranteed to be error free. Simpson Strong-Tie shall not be responsible for any possible loss, damage or (800) 999-5099 injury resulting directly or indirectly from the information contained here. strongtie.com © 2017 Simpson Strong-Tie Company Inc. • P.O. Box 10789, Pleasanton, CA 94588 DIY-CSCHICK17 3/17 exp. 12/20

For more inspiration, visit diydoneright.com