U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 110 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985 Abrasives Grinding Wheels 101 Grinding Wheels Super Abrasives (Diamond & CBN) Grinding Coolant Refractometer Dressing Diamonds Cleaning & Dressing Sticks Grinding Accessories Template Stock Cut-Off Wheels Slip Stones Dressing Sticks Mounted Points Jointer Stone 101 Jointer Stones Cratex Sticks, Wheels & Mounted Points Diamond Sharpeners EZE-LAP DMT Bardo Sanding Wheels Sanding Belt Cleaning Sticks U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 111 Tooling Specialists For The Woodworking Industry Since 1985

GRINDING WHEELS “101” ABRASIVE GRIT SIZE Abrasive grains are sized according to an established Wood Tech continues to maintain the industry’s widest worldwide standard and are designated as a numerical grit selection and largest inventory of grinding wheels: Period. size. The larger the number, the smaller the grain size. Our years of experience has led to many industry leading Coarse grain size (a smaller number) will increase stock innovations that offer you the best grinding wheel tailored to removal rate, but provide less surface finish quality. Fine your particular application. Our product quality is unequaled: grit sizes (larger numbers) provide less stock removal, but that’s why so many of OEM machinery dealers, tooling improve surface quality. Wood Tech uses many wheels distributors, grinding services, and tool rooms worldwide use with combinations of two or more grit sizes to produce our products daily to meet their most demanding grinding improvements in grinding capabilities (for example: our needs. WA462 is a combination of 46 and 60 grit abrasive).

Not all Grinding Wheels are made equal. HARDNESS GRADE Learn how to determine your best value. The hardness grade of wheels are designated by letters With all the different cutting tool options available to select [A (soft) to Z (hard)] This grade represents the amount of from, using the right abrasive is a matter of necessity. It is bond used in the wheel. Generally, harder grades produce a just as important as the choosing the right knife material! better finish, but will have a tendency to load up faster than Our years of experience help you make the right decision. We softer grades. As always, burning of knife material is to be stock wheels to grind all types and grades of knife material avoided; and a wheel with the correct hardness is vital in you need to machine. In order to select the best grinding producing quality ground knives. wheel for your particular application, a general understanding of wheel components is necessary. GRAIN STRUCTURE The combination of abrasive type, abrasive grit size, hardness The grain structure refers to abrasive grain spacing within grade, grain structure and bond type all affect wheel the wheel. This grain density is identified by a number performance. Changes in the amount and type of each of [1 (dense) through 16 (open)]. An open structure wheel will these elements will affect the performance of the wheel. Here be very aggressive, but will not hold it’s form as well. It will are brief descriptions of the elements used to produce wheels. also wear out faster. A denser wheel will generally provide a better finish, but will generate more heat and slower metal ABRASIVE TYPE removal. Finding a happy medium is important in producing a hogging wheel that will remove stock quickly and still The abrasive grain is what actually removes material from the maintain it’s form after dressing. It is just as critical in piece. There are four basic abrasive types: making a finish wheel that hold a small dimension to grind tight corners or small radii. • Aluminum Oxide (high speed steel applications) • Cubic Boron Nitride (CBN) (high speed steel applications) BOND TYPE • Silicon Carbide (carbide grinding applications) • Diamond (carbide grinding applications) The grinding wheel bond (the binding agent), is the material which holds the abrasive grain together. Without the right There are a number of different color wheels on bond, the grinding wheel will literally fly apart. There are the market today; this is not indicative of wheel quality. four major types of bond are: Vitrified (V), Resinoid (B), For example: there are blue colored wheels using conventional Rubber (R), and Metal (M). Selecting the best bond for any blue Aluminum Oxide grain and other blue wheels made with particular application is based on the following properties: a more expensive Ceramic grain. The ceramic grain offers many operators the ability to grind cooler, faster and with 1. Its ability to allow the abrasive grain to be “pulled out” less grinding wheel breakdown. However; most grinders still once the grinding friction becomes too high due to the prefer the more conventional, and less costly, White or Pink grain becoming too dull to properly cut. wheels for most jobs. We can assist you in determining what 2. The bonds ability to properly hold the grain during the abrasive type is best suited for your application. grinding, wheel dressing, and self sharpening applications. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 112 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

GRINDING WHEELS “101” (continued) +Helpful hints to improve grinding results: The vast majority of grinding wheels used in the • Harder knife steels require the use of a softer grinding wheel. woodworking industry use an aluminum oxide abrasive type Conversely, the softer the knife steel, the harder the grinding wheel and a vitrified bond. The are a multitude of variations in must be. each category that manufacturers use to fine tune grinding • Slower machine speeds will make a wheel behave softer. wheel specifications to improve performance. This is not Speeding up the machine will have the opposite effect. a simple task, and Wood Tech’s experience assures you of • If you primarily use a roughing wheel for all your grinding, the best wheel mix to fill your needs. We understand the you can “trick” the wheel into producing a finish grind by applying wax into the wheel to clog it up and lowering the back angle by a few differences in the grinding properties of knife steels; and just degrees. Then increase the RPM’s; this causes the wheel to “buff” as importantly, what grinder you’re using. Your individual rather than grind. grinding technique is also a major factor in wheel selection. • Wheels dressed thinner than 1/8" (3mm) must be 100 grit or finer to avoid breakage and hold proper radii. Our technical staff is ready to help you in making the best • Maintain the correct coolant ratio. We see this as a common decision for your application. source of grinding related issues. Too lean a ratio will result in rust problems; too rich can lead to health risks. We recommend using a handheld refractometer to assure proper ratios. • BE SAFE! NEVER exceed the maximum operating speed of *Surface Feet Per Minute (SFPM) Formula = the wheel. Keep all guards in place. • Follow all the Rules and Safety Guidelines from the Grinding Wheel Diameter x (π or 3.1416) x RPM’s Wheel Institute leaflet that we provide with each shipment. ( 12 ) ROUGH GRINDING WHEEL SPEED RECOMMENDATIONS Type of Grain in Wheel Behavioral Properties of Grinding Wheels *Surface Feet RPM’s Grinding Wheel Diameter Per Minute White Aluminum Oxide 8" (204 mm) Fast stock removal. Less form holding capabilities 3400 to 3900 1600 to 1900 White Aluminum Oxide 8-7/8" (225 mm) Fast stock removal. Less form holding capabilities 3400 to 3900 1500 to 1700 White Aluminum Oxide 10" (254 mm) Fast stock removal. Less form holding capabilities 3400 to 3900 1300 to 1500 Pink Chromium Oxide 8" (204 mm) Aggressive grinding wheel holds form better than 3400 to 3900 1600 to 1900 white wheels. Pink Chromium Oxide 8-7/8" (225 mm) Aggressive grinding wheel holds form better than 3400 to 3900 1500 to 1700 white wheels. Pink Chromium Oxide 10" (254 mm) Aggressive grinding wheel holds form better than 3400 to 3900 1300 to 1500 white wheels. Blue and Pink 8" (204 mm) Very aggressive grinding wheel, resharpens itself, 5000 to 5500 2400 to 2600 Ceramic excellent shape holding capability, excellent on harder steels. Blue and Pink 8-7/8" (225 mm) Very aggressive grinding wheel, resharpens itself, 5000 to 5500 2200 to 2400 Ceramic excellent shape holding capability, excellent on harder steels. Blue and Pink 10" (254 mm) Very aggressive grinding wheel, resharpens itself, 5000 to 5500 1900 to 2100 Ceramic excellent shape holding capability, excellent on harder steels. Blue and White 8" (204 mm) Most aggressive grinding wheel, resharpens itself, 5000 to 5500 2400 to 2600 Ceramic excellent shape holding capability, excellent on harder steels. Blue and White 8-7/8" (225 mm) Most aggressive grinding wheel, resharpens itself, 5000 to 5500 2200 to 2400 Ceramic excellent shape holding capability, excellent on harder steels. Blue and White 10" (254 mm) Most aggressive grinding wheel, resharpens itself, 5000 to 5500 1900 to 2100 Ceramic excellent shape holding capability, excellent on harder steels. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 113 Tooling Specialists For The Woodworking Industry Since 1985

The Industry’s Largest Selection of Stocked Grinding Wheels Over 20,000 Wheels in Stock At All Times!

Vitrified Grinding Wheels for Profile Grinders are all in stock! The industry’s largest inventory of Profile Grinding Wheels for Weinig, Foley, SCMI, Wadkin and others. Wood Tech Enterprises, Inc. stocks a large selection of the following types of wheels:

• Vitrified • Ceramic • CBN(Borazon) • Diamond • CDX Diamond • Cut-Off • Bench

WEINIG Grinding Wheels Over 30 different specifications in stock to fit most ANY grinding application.

FOLEY/SCMI Grinding Wheels BA463 Over 40 different specifications in stock to fit most ANY grinding application. Wheels in stock for Foley, SCMI, United, Diehl, Nielsen, UTMA, Fell and others.

Wheels in stock for the following Profile Grinders:

• WADKIN • SCHNEEBERGER • IIDA • JC312 & Others WA462 We also stock a large inventory of the following: • CBN/Borazon • Diamond • Cut-Off Wheels • Saw Gumming Wheels • Bench Wheels • Tool and Cutter Wheels • Silicon Carbide • Planer Grinding Wheels (Powermatic, Buss, Oliver) • Dish Wheels • Cup Wheels • Segments WA462-10 • Slipstones • Dressing Sticks • Diamond Sharpeners • Rubberized Abrasives

SG46-10 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 114 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

WEINIG GRINDING WHEELS

Strict specifications for use on Weinig Rondamat 925,929,930, 931, as well as the new 934, 934N, 935, 936, 960 and 970

Product Number Size Color Grit

WA462 WA462 225 x 5 x 60mm Pink 46/54 (combo) SA462 225 x 5 x 60mm White 46/54 (combo) BA463 225 x 5 x 60mm Gray 46/60 (combo) CB46 225 x 5 x 60mm Blue 46 WA60 225 x 5 x 60mm Pink 60 SA60 225 x 5 x 60mm White 60 WA100 225 x 5 x 60mm Pink 100 BA463 SA100 225 x 5 x 60mm White 100/120 (combo) C80-J5V* 225 x 5 x 60mm Black 80 * Special formulation for rough grinding of carbide

CERAMIC WEINIG WHEELS • Higher metal removal rates decrease cycle time • Grind cooler to provide better finish and decrease chances for burn damage • Reduced dressing for less erosion and downtime •Draws less power so grinding equipment runs efficiently WA60 Product Number Size Color Grit SG46 225 x 5 x 60mm Blue/White 46 SG46T 225 x 5 x 60mm Blue/White 54 Wonder Wheel 225 x 5 x 60mm Blue/Pink 46 WEI-100712 225 x 5 x 60mm Blue 54

OEM & OTHER WEINIG WHEELS SA60

Product Number Size Color Grit WEI-100719 225 x 5 x 60mm Blue Alum. Ox 46/54 (combo) TT46(x4027) - Wood Tech 225 x 5 x 60mm Purple/Blue 54 Product Cross Reference for WEI-100719 WEI-100717 225 x 5 x 60mm Blue Alum. Ox 100 WEI-006-00182 225 x 5 x 60mm Gray 54 TT46 WEI-100712 225 x 5 x 60mm Blue Ceramic 54

ORIGINAL WEINIG WHEELS IN STOCK!

SG46 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 115 Tooling Specialists For The Woodworking Industry Since 1985

GRINDING WHEELS FOR SCMI, FOLEY, UNITED, DIEHL DMG12, JEFFER, CANTEK, NIELSEN and others

• Available in 1/8", 3/16" and 1/4" thicknesses. The tightest tolerances are maintained to lessen vibration and increase grinding accuracy. • 1/8" wheels have a raised hub and are 1/4" thick at the bore for added stability and safety. • 1/4" and 3/16" are a Type 1 (straight wheel)

Specify thickness needed when ordering Product Number Size-1/8" (Raised Hub) Color Grit WA462-10 10 x 1/8" x 1-1/4" Pink 46/54 (combo) SA462-10 10 x 1/8" x 1-1/4" White 46/54 (combo) WA462-10 CB46-10 10 x 1/8" x 1-1/4" Blue 46 SA54-10 10 x 1/8" x 1-1/4" White 54 WA60-10 10 x 1/8" x 1-1/4" Pink 60 SA60-10 10 x 1/8" x 1-1/4" White 60 WA80-10 10 x 1/8" x 1-1/4" Pink 80 SA80-10 10 x 1/8" x 1-1/4" White 80 WA100-10 10 x 1/8" x 1-1/4" Pink 100 SA100-10 10 x 1/8" x 1-1/4" White 100 WA60 -10 Product Number Size-3/16" Color Grit WA462-10S(3/16) 10 x 3/16" x 1-1/4" Pink 46/54 (combo) SA462-10S(3/16) 10 x 3/16" x 1-1/4" White 46/54 (combo) SA54-10S(3/16) 10 x 3/16" x 1-1/4" White 54 WA60-10S(3/16) 10 x 3/16" x 1-1/4" Pink 60 SA60-10S(3/16) 10 x 3/16" x 1-1/4" White 60 WA80-10S(3/16) 10 x 3/16" x 1-1/4" Pink 80 SA80-10S(3/16) 10 x 3/16" x 1-1/4" White 80 WA100-10S(3/16) 10 x 3/16" x 1-1/4" Pink 100 SA60-10 SA100-10S(3/16) 10 x 3/16" x 1-1/4" White 100

Product Number Size-1/4" Color Grit WA462-10S 10 x 1/4" x 1-1/4" Pink 46/54 (combo) SA462-10S 10 x 1/4" x 1-1/4" White 46/54 (combo) SA54-10S 10 x 1/4" x 1-1/4" White 54 WA60-10S 10 x 1/4" x 1-1/4" Pink 60 SA60-10S 10 x 1/4" x 1-1/4" White 60 WA80-10S 10 x 1/4" x 1-1/4" Pink 80 SA80-10S 10 x 1/4" x 1-1/4" White 80 WA100-10S 10 x 1/4" x 1-1/4" Pink 100 WA462-10S(3/16) SA100-10S 10 x 1/4" x 1-1/4" White 100 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 116 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

CERAMIC GRINDING WHEELS • Higher metal removal rates decrease cycle time • Grind cooler to provide better finish and decrease chances for burn damage • Reduced dressing for less erosion and downtime • Draws less power so grinding equipment runs efficiently

Product Number Size Color Grit SG-46-10S 10 x 1/4" x 1 1/4" Blue 46 SG46-10 Dressed to 1/8" 10 x 1/4" x 1/4"(1/8" Raised Hub) Blue 46 SG100-10S 10 x 1/4" x 1-1/4" Blue 100 SG46-10 SG46-8S 1 8 x 1 x 3/4” bushing to 5/8” Blue 46 SG46-7S 1 7 x 1 x 3/4” bushing to 5/8” Blue 46 SG46-6S 6 x 3/4 x 5/8” bush to 1/2 Blue 46 Other sizes and grit selections available from stock. Call for availability. FOLEY 8" & DIEHL DPG-10 GRINDING WHEELS

Product Number Size Color Grit WA462-8* 8 x 1/8" x 1-1/4" Pink 46/54 (combo) SA60-8 8 x 1/8" x 1-1/4" White 60 SA60-8RH* 8 x 1/8" x 1-1/4" White 60 WA100-8* 8 x 1/8" x 1-1/4" Pink 100 WA462-8S 8 x 1/4" x 1-1/4" Pink 46/54 (combo) SA60-8S 8 x 1/4" x 1-1/4" White 60 WA100-8S 8 x 1/4" x 1-1/4" Pink 100 WA462-8S(3/16) 8 x 3/16 x 1-1/4" Pink 46/54 (combo) WA462-8 SA100-8S(3/16) 8 x 3/16" x 1-1/4" White 100 *Dressed to 1/8" with 1/4" thickness at bore for stability. WADKIN GRINDING WHEELS Part# Description WAD-GW202 220 grit finishing wheel WAD-GW203 60 grit general purpose wheel WAD-GW204N 60 grit general purpose wheel WAD-GW248 Finishing wheel for Weinig grinders WAD-GW249 Roughing wheel for Weinig grinders WAD-GW292N 60 grit general purpose wheel WAD-GW294 60 grit general purpose wheel WAD-GW271C Ceramic general purpose wheel

VIEL GRINDING WHEELS

Product Number Size Color Grit WONDER-VIEL 7-1/4" x 3/16 x 1-1/4" Purple Ceramic 46 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 117 Tooling Specialists For The Woodworking Industry Since 1985

WADKIN, AUTOOL & SCM PROFILMAX 300X

Product No. Size Color Grit SA46-9 9 x .187" x 1-1/4" White 46 BA463-9 9" x 5mm x 1-1/4" Gray 46/60 (combo) SG46-9 9 x .187" x 1-1/4" Blue Ceramic 46 WA60-9 9 x 3/16" x 1-1/4" Pink 60 Bushings* 60mm OD x 1-1/4" ID N/A N/A

IIDA

Product Number Size Color Grit SA54-IIDA 9 x .187" x 32mm White 54 SA100-IIDA 9 x .187" x 32mm White 100 Bushings* (32mm) 60mm OD x 32mm ID N/A N/A * By using this precision metal bushing, convert a lower priced Weinig size wheel to run on your grinder. A real cost savings!

SCHNEEBERGER

Product Number Size Color Grit WA462-SCHN 200 x 6 x 20mm Pink 54 SG46-SCHN 200 x 6 x 20mm Blue Ceramic 46 WA100-SCHN (4) 200 x 4 x 20mm Pink 100 WA100-SCHN (3) 200 x 3 x 20mm Pink 100 A80-PCBC33 200 x 2 x 20mm Black Cutoff Wheel 80

TOOLSET – MODEL #16

Product Number Size Color Grit WA462-TS16 200 x 5 x 32mm Pink 46/54 (combo) SA60-TS16 200 x 5 x 32mm White 46/54 (combo) WA100-TS16 200 x 5 x 32mm White 100

PLANER GRINDING WHEELS

Part No# Machine Description Color Grit Planr-Buss Buss 5 x 1/2 x 1-1/2" Pink 46 Planr-Buss(60) Buss 5 x 1/2 x 1-1/2" Pink 60 Planr-Del Delta 3-3/4 x 1/4 x 2" White 46 Planr-Del 5 Delta 5 x 3/8 x 2" White 46 Planr-Olive Oliver 4-1/2 x 1/2 x 1-3/8" White 46 Planr-Powr Powermatic 4-1/2 x 1/2 x 1-1/2" White 46 Part# PLANR-BUSS Planr-SCM SCMI 4-5/8 x 1/2 x 1/2" Gray 46 SA60-4.5S 5/8" Baxter Whitney 4 x 5/8 x 1-1/4" White 60 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 118 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

Bench Grinding Wheels Wood Tech stocks a wide range of bench grinding wheels designed for the most demanding grinding applications. Other sizes and shapes of wheels available upon request.

6" Diameter Wheels; 5/8" Bore (Can be bushed to 1/2" ID)

Thickness 46 Grit Part # 60 Grit Part # 100 Grit Part # 1/8" WA462-6S (1/8") WA100-6S (1/8") 1/4" 32A46-6S (1/4") WA60-6S (1/4") WA100-6S (1/4") SA = White Wheel 1/2" WA462-6S (1/2") SA60-6S (1/2") WA100-6S (1/2") WA = Pink Wheel 3/4" 32A46-6S (3/4") 32A60-6S (3/4") SA100-6S (3/4") 1" SA60-6S (1") SA100-6S (1") 32A = Gray (Salt & Pepper) Wheel

CERAMIC WHEELS 7" Diameter Wheels; 1-1/4" Bore (Bushings available to your ID) are available from stock in a wide variety of grits and sizes. Thickness 46 Grit Part # 60 Grit Part # 80 Grit Part # 100 Grit Part # 1/8" WA60-7S (1/8") 3/16" 32A46-7S (3/16") 1/4" 32A46-7S (1/4") SA60-7S (1/4") SA80-7S (1/4") WA100-7S (1/4") 1/2" SA46-7S (1/2") SA60-7S (1/2") SA80-7S (1/2") SA100-7S (1/2") 3/4" SA46-7S (3/4") 32A60-7S (3/4") SA80-7S (7/8") 1" WA46-7S (1") WA60-7S (1") SA80-7S (1") SA100-7S (1")

* On 8" and 10" diameter wheels: the 8" Diameter Wheels; 1-1/4" Bore (Bushings available to your ID) 1/8" thickness wheel is a raised hub wheel with 1/4" thick hub for stability. Thickness 46 Grit Part # 60 Grit Part # 80 Grit Part # 100 Grit Part # 1/8"* WA462-8 (1/8") SA60-8 (1/8") WA100-8 (1/8") 3/16" WA462-8S (3/16") SA60-8S (3/16") WA100-8S (3/16") 1/4" WA462-8S (1/4") SA60-8S (1/4") WA80-8S (1/4") WA100-8S (1/4") 3/8" SA46-8S (3/8") WA80-8S (3/8") 1/2" WA462-8S (1/2") SA60-8S (1/2") SA80-8S (1/2") SA100-8S (1/2") 3/4" 32A46-8S (3/4") SA60-8S (3/4") SA150-8S (3/4") 1" 32A46-8S (1") WA60-8S (1") SA100-8S (1")

10" Diameter Wheels; 1-1/4" Bore (Bushings available to your ID)

Thick- 46 Grit Part # 60 Grit Part # 80 Grit Part # 100 Grit Part # ness 1/8"* WA462-10 (1/8") WA60-10 (1/8") SA80-10 (1/8") WA100-10 (1/8") 3/16" WA462-10S (3/16") WA60-10S (3/16") SA100-10S (3/16") 1/4" WA462-10S (1/4") WA60-10S (1/4") SA80-10S (1/4") WA100-10S (1/4") Wood Tech stocks wheels in 12", 14" and many other 3/8" SA462-10S (3/8") WA100-10S (3/8") sizes. Custom sizes and 1/2" WA462-10S (1/2") SA60-10S (1/2") 32A100-10S (1/2") their specifications are available upon request. 3/4" WA462-10S (3/4") WA60-10S (3/4") 1" WA462-10S (1") SA60-10S (1") U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 119 Tooling Specialists For The Woodworking Industry Since 1985

SUPER ABRASIVE WHEEL GENERAL INFORMATION

DIAMOND WHEELS are used to grind carbide only. CBN WHEELS are used to grind M-2 steel for superior finish. CDX WHEELS are used to grind carbide inlay, Bak-Pak, Double Back & other sandwich type carbide knife systems and steel body at the same time on corrugated and flat planer knives. See page 104 for more information.

WHEEL TYPE - D1A1 for straight knife grinding. D1FF1, D3F1 or D14F1 for profiling applications. (D3F1 is a wheel with a raised hub on one side for better stability on thinner wheels, D14F1 with raised hub on both sides.)

GRIT SELECTION - For fast stock removal where finish is not critical, use grits Super Abrasive Wheel between 60 and 100. When finish is a consideration, along with stock removal - use grits between 120 and 180. When finish is critical with little stock removal, use grits of 220 and above.

HARDNESS - For Wet grinding use a medium hardness (R Hardness) D1A1 Square

CONCENTRATION RECOMMENDATIONS: • Diamond Wheels – 100 concentration D1FF1 Radius • CBN and CDX Wheels – 75 concentration D3F1 Radius (Hub one side)

BOND RECOMMENDATIONS - For wet grinding a resinoid bond. D14F1 Radius Profile Grinder Recommendations: (Hub both sides) Run the grinding wheel at maximum wheel speed of not more than 3,000 RPMs. As carbide is a much harder material than standard HSS, a faster wheel speed will allow Typical Wheel Shapes. more efficient grinding. Allow the grinding wheel to do the work, as forcing the wheel Other shapes available. will create unnecessary heat buildup. Heat buildup can cause the carbide to crack or delaminate.

Wadkin Superabrasive Wheels and Cups

Part # Description

GW209 4.7mm flat diamond wheel

GW211 3mm round diamond wheel

GW213 3mm 30° diamond wheel 3mm 45° diamond wheel GW214 GW215 3mm radius diamond wheel

GW216 3mm 45° diamond wheel

GW231 8 mm borazon wheel

GW241 3 mm borazon wheel GW301 8mm borazon cup wheel for NZ/NU GW303 8mm diamond cup wheel for NZ/NU Part # GW301 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 120 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

Weinig Super Abrasive Wheels

Diamond Type Grit Dimension Depth 1/8" WD3-8DIA D1A1 Square 80-120 200 x 3 x 60mm WF2-8DIA D3F1 Radius 120-220 200 x 2 x 60mm WF3-8DIA D1FF1 Radius 120-220 200 x 3 x 60mm WF4-8DIA D1FF1 Radius 120-220 200 x 4 x 60mm

Diamond Type Grit Dimension Depth 1/4" WD3-4DIA D1A1 Square 80-120 200 x 3 x 60mm Weinig Super WF2-4DIA D3F1 Radius 120-220 200 x 2 x 60mm Abrasive Wheel WF3-4DIA D1FF1 Radius 120-220 200 x 3 x 60mm WF4-4DIA D1FF1 Radius 120-220 200 x 4 x 60mm

CDX Depth 1/8" Type Grit Dimension D1A1 Square WD3-8CDX D1A1 Square 80-120 200 x 3 x 60mm WF2-8CDX D3F1 Radius 120-220 200 x 2 x 60mm D1FF1 Radius WF3-8CDX D1FF1 Radius 120-220 200 x 3 x 60mm D3F1 Radius WF4-8CDX D1FF1 Radius 120-220 200 x 4 x 60mm (Hub one side)

D14F1 Radius CDX Depth 1/4" Type Grit Dimension (Hub both sides) WD3-4CDX D1A1 Square 80-120 200 x 3 x 60mm WF2-4CDX D3F1 Radius 120-220 200 x 2 x 60mm Typical Wheel Shapes. Other shapes available. WF3-4CDX D1FF1 Radius 120-220 200 x 3 x 60mm WF4-4CDX D1FF1 Radius 120-220 200 x 4 x 60mm

CBN Depth 1/8" Type Grit Dimension WD3-8CBN D1A1 Square 80-120 200 x 3 x 60mm WF2-8CBN D3F1 Radius 120-220 200 x 2 x 60mm WF3-8CBN D1FF1 Radius 120-220 200 x 3 x 60mm WF4-8CBN D1FF1 Radius 120-220 200 x 4 x 60mm

CBN Depth 1/4" Type Grit Dimension WD3-4CBN D1A1 Square 80-120 200 x 3 x 60mm WD10-4CBN D1A1 Square 180 200 x 10 x 60mm WF2-4CBN D3F1 Radius 120-220 200 x 2 x 60mm WF3-4CBN D1FF1 Radius 120-220 200 x 3 x 60mm WF4-4CBN D1FF1 Radius 120-220 200 x 4 x 60mm Weinig #909 & #912 wheels

Part Number Type Grit CBN Depth Dimension Face Width 6A92B 6A2 Cup 100 1/8" 5" x .709" x 20 mm 1/8" Weinig #909 & #912 wheel D4-A1H 4A1 Dish 100 5/64" 150 x 17 x 20 mm 1/8" Part # 6A92B Diamond and other wheels are available. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 121 Tooling Specialists For The Woodworking Industry Since 1985

Foley, Diehl, Nielsen Super Abrasive Wheels

Diamond Type Grit Dimension D1A1 Square Depth 1/8" FD4-8DIA D1A1 80-120 10" x 1/4" x 1-1/4" D1FF1 Radius FF4-8DIA D3F1 120-220 10" x 1/4" x 1-1/4" u=1/8", r=1/16" UD4-8DIA D1FF1 120-220 8" x 1/4" x 1-1/4" D3F1 Radius (Hub one side) UF4-8DIA D3F1 120-220 8" x 1/4" x 1-1/4" u=1/8", r=1/16" D14F1 Radius Diamond Type Grit Dimension (Hub both sides) Depth 1/4" FD4-4DIA D1A1 80-120 10" x 1/4" x 1-1/4" Typical Wheel Shapes. Other shapes available. FF4-4DIA D3F1 120-220 10" x 1/4" x 1-1/4" u=1/8", r=1/16" UD4-4DIA D1FF1 120-220 8" x 1/4" x 1-1/4" UF4-4DIA D3F1 120-220 8" x 1/4" x 1-1/4" u=1/8", r=1/16"

CDX Depth 1/8" Type Grit Dimension FD4-8CDX D1A1 80-120 10" x 1/4" x 1-1/4" FF4-8CDX D3F1 120-220 10" x 1/4" x 1-1/4" u=1/8", r=1/16" UD4-8CDX D1FF1 120-220 8" x 1/4" x 1-1/4" UF4-8CDX D3F1 120-220 8" x 1/4" x 1-1/4" u=1/8", r=1/16"

CDX Depth 1/4" Type Grit Dimension FD4-4CDX D1A1 80-120 10" x 1/4" x 1-1/4" FF4-4CDX D3F1 120-220 10" x 1/4" x 1-1/4" u=1/8", r=1/16" UD4-4CDX D1FF1 120-220 8" x 1/4" x 1-1/4" UF4-4CDX D3F1 120-220 8" x 1/4" x 1-1/4" u=1/8", r=1/16"

CBN Depth 1/8" Type Grit Dimension FD4-8CBN D1A1 80-120 10" x 1/4" x 1-1/4" FF4-8CBN D3F1 120-220 10" x 1/4" x 1-1/4" u=1/8", r=1/16" UD4-8CBN D1FF1 120-220 8" x 1/4" x 1-1/4" UF4-8CBN D3F1 120-220 8" x 1/4" x 1-1/4" u=1/8", r=1/16" FF4-8DIA (10 x 1/4 x 1-1/4" u = 1/8", r = 1/16") CBN Depth 1/4" Type Grit Dimension FD4-4CBN D1A1 80-120 10" x 1/4" x 1 1/4" FF4-4CBN D3F1 120-220 10" x 1/4" x 1 1/4" u=1/8", r=1/16 UD4-4CBN D1FF1 120-220 8" x 1/4" x 1 1/4" UF4-4CBN D3F1 120-220 8" x 1/4" x 1 1/4" u=1/8", r=1/16"

u = This refers to the thickness of the wheel at the outside periphery r = This refers to the radius. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 122 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

GRINDING COOLANT SAFETY-COOL 9951 For Fast Cooling on Hot Jobs! GENERAL DESCRIPTION: SAFETY-COOL 9951 is a synthetic cutting fluid concentrate used for cutting and grinding all metals. It is particularly effective on hardened tool steels and high-speed operations because superior wetting qualities allow it to penetrate to the edge of the cutting tool and quickly dissipate heat.

SAFETY-COOL 9951 allows increased feeds and speeds; permits greater production and increases tool life by preventing heat accumulation and inhibiting rust formation. Recommended dilution ratio (40:1) SAFETY-COOL 9951 out performs ordinary and grinding fluids by providing exceptional lubricating properties. Wheels stay open for faster metal removal, less wheel dressing, decreased wheel wear and loading, improved finish and increased production.

SYNTILO® 9918 Is an operator friendly – Neutral pH synthetic cutting and grinding fluid that combines optimum machining performance with minimal mist—resulting in less dermatitis. This increases productivity with higher operator acceptance! KEY PERFORMANCE BENEFITS • Low Mist – Low Odor • Low foaming Refractometer • Excellent rust protection • Prevents bimetallic corrosion • Minimizes rancid odors • Excellent bioresistence • Settles chips and swarf quickly for • Reduces down time by a cleaner work area extending system life

Product Number Description Standard Package SC-9951-1 1 Gallon of Safety-Cool 9951 1 Gallon Jug SC-9951-5 5 Gallons of Safety-Cool 9951 5 Gallon Bucket SC-9918-1 1 Gallon of Safety-Cool 9918 1 Gallon Jug Ways to Extend SC-9918-5 5 Gallons of Safety-Cool 9918 5 Gallon Bucket +A Helping Coolant Life: Hand

1. Regular Filter Changes REFRACTOMETER

2. A sediment trap to catch the With the Refractometer Coolant Tester, you can save money two ways…by using only majority of metal filters will help as much coolant as you need and by better maintaining your equipment for longer life. greatly in life extension. A clean one gallon container with the return Proper concentration of coolant saves money upfront and in the long run. A cutting line from the grinder going into it and grinding mixture that is too rich will waste expensive coolant, while a mixture will act as a sediment trap. that is too lean can shorten the usable life of equipment. Better monitoring of coolant can improve grinding finish, increase wheel life, and control corrosion. 3. Put a large magnet (in a self- sealing bag) in your tub near the • Optimizes coolant use and tool life drain hole to catch a lot of ferrous • Graduation (%) 0.2 • Easy to Use metal finings prior to them going • Solution measuring range (%) 0-32 • Accurately measures coolant concentration into the coolant reservoir. • Includes instructions and case • Use for general purpose application 4. Add an aquarium pump to keep the coolant moving. This increases coolant life. Product Number Description REFRACTOMETER Coolant Tester U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 123 Tooling Specialists For The Woodworking Industry Since 1985

DRESSING DIAMONDS

WEINIG, FOLEY, DIEHL, WADKIN, SCM, SCHNEEBERGER, UTMA AND OTHER GRINDERS

Product Number Description Machine SPS33B 1-1/8 x 5/16" Shank 1/3 ct. Weinig 930, 931, 932, 934, 935, 936 SPS925 Dressing Diamond for 925 & Weinig 925, 934N, 950, 960, 934N threaded 970 SPS929 Dressing Diamond for 929 Weinig 929 G-3 SCHN 1-3/8" x 10mm Dressing Schneeberger Sculptor Diamond SPS33B G-312 6 mm partial thread Jeffer JC 312 G-317 2 x 5/16" - 24 thread 1/3 ct. Foley 75-12, SCMI 75-12 with knob (old style) G-317-SCMI 2-1/4 x 1/4" - 28 partial thread. Foley-746, SCMI-746 1/3 thread (new style) G-319 Dressing Diamond 2 x 1/4"-28 Foley G-320 Dressing Diamond for UTMA UTMA P-30 SPS925 P-30 G-317 DIEHL-4135-001 Dressing Diamond for DPG-15 Diehl DPG-15, DPG-20 G-330 2 x 5/16" - 18 thread 1/3 ct. Diehl “Older Models" uses 10" dia. wheel G-300 NV300, Visage, Most Wadkins, Silhouette Grinders SCM ProfileMax 300 G-IIDA PKG-2 2 pc. Diamond Tipped Dresser IIDA PKG-231 G-300 G-317-SCMI G-TS16 Dressing Wheel SCM Toolset 16 G-VIEL Dressing Diamond for Viel Viel Profile Grinder G-AMML Dressing Diamond 3" long x General purpose G-312 3/8" 1/3ct. HAND-DRESSER 6" Hand Diamond Dresser General purpose WEI-700070 DIA/CBN Wheel Dresser Weinig 930, 931, 932, 934, 935, 936 G-IIDA PKG-231 CLEANING STICKS

Product Number Description Use STK6100 1 x 1 x 6" square Cleaning and Hand Dressing stick for Vitrified Wheels BDS6100 1 x 1 x 6" square Cleaning and Hand Dressing stick for Super Abrasive Wheels BDS3175 1/4 x 3/4 x 4" Cleaning and Hand Dressing stick for Super Abrasive Wheels NORBIDE STICK & Other Super Abrasive Dressing Tools

Product Number Description Use Norbide Stick 5/16" x 1/2" x 3" Diamond & CBN hand dressing stick JSGC400-1/2 4 1/2" x 1/2" x 4" For face dressing of super abrasive wheels

U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 124 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

WEINIG & DIEHL PROFILE GRINDER ACCESSORIES

Product # Description Std. Pkg. FP931 Weinig 931 Filter Sheets 100 pc pk TR935 TR931 TR931 Weinig 930,931,934,935,936, 960, 970 Tool Rest 1 piece TR935 Weinig 935,936,970 1 piece Beveled Tool Rest for auto-grind TR929/950P Weinig 929,950 – Tool rest for profiling 1 piece TR929/950S Weinig 929,950 – Tool rest for straight knives 1 piece TP931-1 Weinig & Diehl Stylus 2mm 1/2 round 1 piece TP931-1 TP931-2 TP931-2 Weinig & Diehl Stylus 3mm Rnd/4mm (1/2 Rnd) 1 piece TP931-2A Weinig & Diehl Stylus 4mm 1/2 Round 1 piece TP931-3 Weinig & Diehl Stylus 4mm, 45dg point 1 piece TP931-4 Weinig & Diehl Stylus 3 mm 1/2 Round 1 piece TP931-5 Weinig & Diehl Stylus 30° Double Angle 1 piece GWC931 GWC935 TP931-6 Weinig & Diehl Stylus 6mm 1/2 Round 1 piece TP931-9 Weinig & Diehl Stylus 1.5 mm 1/2 Round 1 piece TP931-10 Weinig & Diehl Stylus 4mm Round/ 2mm Round 1 piece GWC931 TP925-2 2mm round Weinig Stylus 925, 950 1 piece W/wheel mounted TP925-3 3mm round Weinig Stylus 925, 950 1 piece TP925-4 4mm round Weinig Stylus 925, 950 1 piece GWC931 Weinig 931, 930,925,929,934N 1 piece Grinding Wheel Collar GWC935 Weinig 935,936,932,934 & DIEHL DPG-20 Grinding Wheel Collar 1 piece ROND1 ROND 1 Rondor Stone 1 piece RONDOR Wheel Dresser RONDOR Rondor Wheel Dresser Complete 1 piece WHEEL SPS925 Weinig Dressing Diamond (Threaded) 1 piece SPS33B Weinig Dressing Diamond (Smooth shank) 1 piece SPS33B SC9951-1 1 Gallon Grinding Coolant Concentrate 1 Gal. Jug SPS925 SC9951-5 5 Gallons Grinding Coolant Concentrate 1 Pail

WADKIN & AUTOOL PROFILE GRINDER ACCESSORIES Wood Tech stocks a wide variety of tooling and spare machine parts for Wadkin grind- ers and moulders. Please call 1-800-TOOLING for your particular needs.

Part # Wadkin Product # Description TPNX-4,7 NX 0040 Wadkin/Autool Stylus 4,7 mm 1/2 round TPNX-3 NX 0133 Wadkin/Autool Stylus 3 mm 1/2 round TPNX-2 n/a Wadkin/Autool Stylus 2 mm 1/2 round TPNX-1,6 n/a Wadkin/Autool Stylus 1,6 mm 1/2 round G300 NXU522 Wadkin Dressing Diamond G-300 TS-WADKIN NXT6 13" Template Steel with predrilled holes TPNX-4.7 TR- WADKIN NX454 Tool Rest U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 125 Tooling Specialists For The Woodworking Industry Since 1985

SCMI 746 PROFILE GRINDER ACCESSORIES Wood Tech Enterprises stocks various replacement parts for both the SCMI and older style Foley profile grinders. SCMI has made many modifications to the original Foley machine. Should you have any questions concerning which part is correct for your machine, please contact us for assistance. Grinding Wheels are available in a multitude of grit options and are available in 1/8", 1/16" and 1/4" thicknesses. All wheels are 10" diameter with 1 1/4" bore. Other sizes are available from stock. (See page 115.)

Our Product Number SCM’s Product No. Description G317-SCMI 7469461 SCMI Dressing Dia. 1/4" thick x 2-1/4" Long (Partially Threaded) TPSCMI-1(SCMI) 7469230 SCMI Stylus 1/16" Radius TPSCMI-2(SCMI) 7469231 SCMI Stylus 1/8" Radius TPSCMI-3(SCMI) 7469232 SCMI Stylus 3/16" Radius TPSCMI-4(SCMI) N/A SCMI Stylus 1/4" Radius TPSCMI-6(SCMI) 7469228 SCMI Stylus 1/8" Square End G-317-SCMI TPSCMI-TRI(SCMI) 7469234 SCMI Stylus Triangle TR746 7469460 Tool Rest for SCMI (Hydro Blade) TPSCMI-2 GWC7512 7469550 Grinding Wheel Hub Assy (3" Dia.) FS7512 3709503 Filter Socks for SCMI SC9951 1 Gallon 1 Gallon Grinding Coolant SC9951 5 Gallons 5 Gallons Grinding Coolant TR746 SCM-3709124 3709124 Multi Ribbed V-belt for newer model 75-12 & 746

FOLEY 75-12 PROFILE GRINDER ACCESS. Our Product No. Foley’s Product No. Description G317 7469588 Dressing Diamond 5/16" thick x 2" Long Fully Threaded with knob TPFU-1 7469032 Foley Stylus 1/16" * TPFU-2 7469033 Foley Stylus 1/8" * TPFU-3 7469034 Foley Stylus 3/16" * GWC7512 TR7512 7469059 Foley #7512 Tool (Tooth Rest) Plate TR7512 (Hydro Blade) GWC7512 7469550 Grinding Wheel Hub Assy (3" Dia.) FS7512 3709503 Filter Socks for Foley SCM-3709122 3709122 V-belt for older model 75-12 G-317

* Stylus may fit some Diehl DPG-10 Grinders U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 126 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

IIDA PKG-231 PROFILE GRINDER ACCESSORIES Wood Tech stocks a wide variety of tooling for IIDA grinders and moulders. IIDA 3MM RD Please call 1-800-TOOLING for your particular needs.

Part # Description Standard Package IIDA 2MM RD IIDA Stylus 2 mm Round 1 Piece IIDA 3MM RD IIDA Stylus 3 mm Round 1 Piece IIDA 4MM RD IIDA Stylus 4 mm Round 1 Piece IIDA 4MM SQ IIDA Stylus 4 mm Square 1 Piece G-IIDA PKG-231 IIDA 5MM RD IIDA Stylus 5 mm Round 1 Piece IIDA 5MM SQ IIDA Stylus 5 mm Square 1 Piece G-IIDA PKG-231 2 pc. Diamond Tipped Dresser 2 Piece Set (1 right, 1 left) TR-IIDA PKG-231 TR-IIDA PKG-231 Knife Tool Rest 1 Piece For grinding wheels for IIDA, see page 117. JEFFER/CANTEK JC312 PROFILE GRINDER ACCESSORIES Wood Tech stocks a wide variety of tooling for Jeffer/Cantek JC312 grinders and moulders. Please call 1-800-TOOLING for your particular needs.

Part # Description Std. Pkg. TPJC312-2MM JC312-Stylus 2 mm Round 1 Piece TPJC312-3MM JC312-Stylus 3 mm Round 1 Piece TPJC312-BB JC312-Stylus 4 mm Ball Bearing (Straight Knives) 1 Piece TPJC312-4MM TPJC312-4MM JC312-Stylus 4 mm Round 1 Piece TPJC312-4MMBEV JC312-Stylus 4 mm Double Bevel (30° &60°) 1 Piece TPJC312-4MMSQ JC312-Stylus 4 mm Square 1 Piece G-312 TPJC312-6MM JC312-Stylus 6 mm Round 1 Piece G-312 Dressing Diamond for JC312 1 Piece TR-JC312 Knife Tool Rest for JC312 1 Piece For grinding wheels for Jeffer/Cantek JC312, see page 115. SCHNEEBERGER SCHULPTOR PROFILE GRINDER ACCESSORIES Wood Tech stocks a wide variety of tooling for the Schneeberger Schulptor grinder.

Part # Description Standard Package TPSCHN-2.5MM TPSCHN-1.5MM Schulptor-Tracing Pin 1,5mm Radius 1 piece TPSCHN-2.5MM Schulptor-Tracing Pin 2,5mm Radius 1 piece TPSCHN-2.6MM Schulptor-Tracing Pin 2,6mm Radius 1 piece TPSCHN-2MM Schulptor-Tracing Pin 2mm Round 1 piece TPSCHN-3MM Schulptor-Tracing Pin 3mm Radius 1 piece G-SCHN Dressing Diamond for Schulptor 1 piece TR-SCHN Tool Rest (Copy Finger) for Schulptor 1 piece TR-SCHN For grinding wheels for Schneeberger Schulptor, see page 117. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 127 Tooling Specialists For The Woodworking Industry Since 1985

TEMPLATE STOCK

Wood Tech Enterprises offers three type of template stock: Pre-blued (PB) with rolled edges and oil hardening (OH) Scheffield steel with square edges and plastic stock for template routers. This special cast acrylic material is specially formulated for use on template routing machines.

Product Number Description RC TS36163 36 x 1/16 x 3" (PB) 48-50 TS36164 36 x 1/16 x 4" (PB) 48-50 TS18323 18 x 3/32 x 3" (OH) Varies with tempering TS18324 18 x 3/32 x 3" (OH) Varies with tempering TS-WADKIN 13" Template Steel for Wadkin Grinder, Part No.# NXT6 with predrilled holes. TSPlastic 1/8" 12 x 1/8 x 4" N/A TSPlastic 3/16" 12 x 3/16 x 4" N/A NXT-9 14" long Cast Acrylic template material N/A for Wadkin template routers

CUT-OFF WHEELS

Wood Tech Enterprises carries these cut-off wheels for the cutting of knife steel and other applications. Internally reinforced for better stability. Other sizes are available.

Product Number Specifications Size A60-616 A60 QBF 6 x 1/16 x 1/2" A36-618 A36 T BFI 6 x 1/8 x 1" A80-PCBC33 A80-PCBC33 200 x 2 x 20 mm A60-816 A60 QBF 8 x 1/16 x 1/2" A60-818 A60 QBF 8 x 1/8 x 1/4" A60-1032 A60 QBF 10 x 3/32 x 1" A36-1018 A36 10 x 1/8 x 3/4" A60-1216A A60 QBF 12 x 1/16 x 1" A60-1216B A60 QBF 12 x 1/16 x 1 1/4" A60-1232 A60 QBF 12 x 3/32 x 1" A30-12764 320A30 FB 12 x 7/64 x 1" A46-1416 A46 14 x 1/16 x 1" A60-1432 A60 QBF 14 x 3/32 x 1" A30-1418 A30P B1FX 14 x 1/8 x 1" SAW GUMMING WHEELS Wood Tech stocks a large selection of resin bonded wheels for snagging and saw gumming wheels. Call us with your size requirements for availability. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 128 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

SLIP STONES Great for: • Deburring Knives • Honing • Taking Nicks Out

Most slip stones are available in black silicon carbide (C) and (dry or oiled-filled) aluminum oxide (A). Please specify abrasive type when ordering. For example: TA183A = Aluminum Oxide (better finish), and TA183C = Silicon Carbide (faster cutting and most popular). FAS-4 Hard Arkansas Stone

Product Number Grit Size TA445-F 320 4 x 1 x 1/8 x 1/32" TA445-M 180 4 x 1 x 1/8 x 1/32" TA445-C 120 4 x 1 x 1/8 x 1/32" TA-186 320 4 x 1 x 7/16 x 3/16" TA-187 180 4 x 1 x 7/16 x 3/16" TA-189 120 4 x 1 x 7/16 x 3/16" TA-177 320 4-1/2 x 1-3/4 x 1/4 x 1/16" TA183 Silicon Carbide TA-178 180 4-1/2 x 1-3/4 x 1/4 x 1/16" Slip Stone TA-179 120 4-1/2 x 1-3/4 x 1/4 x 1/16" TA446-F 320 4-1/2 x 1-3/4 x 3/8 x 1/8" TA446-M 180 4-1/2 x 1-3/4 x 3/8 x 1/8" TA446-C 120 4-1/2 x 1-3/4 x 3/8 x 1/8" TA-183 or FS-44 320 4-1/2 x 1-3/4 x 1/2 x 3/16" TA-184 180 4-1/2 x 1-3/4 x 1/2 x 3/16" TA-185 120 4-1/2 x 1-3/4 x 1/2 x 3/16" TA-180 320 4-1/2 x 2 -1/8 x 5/8 x 5/16" TA-181 180 4-1/2 x 2 -1/8 x 5/8 x 5/16" TA-182 120 4-1/2 x 2 -1/8 x 5/8 x 5/16" TA-293-F 320 5 x 1 x 5/16 x 3/32" TA-293-M 180 5 x 1 x 5/16 x 3/32" TA-174 320 6 x 2 1/4 x 3/4 x 3/8" TA-175 180 6 x 2 1/4 x 3/4 x 3/8" TA-176 120 6 x 2 1/4 x 3/4 x 3/8" FAS-4 Fine Arkansas Stone (Hard) 4 x 2 x 1/2 x 1/8 TRA-001A Various 13 piece Tool Room Assort. TRA-Ceramic Various 1/4" x 5" long ceramic 4 piece assort. w/pouch

A Helping Hand Slip Stone Lubricant Formula: + (keeps stones at peak performance) Mix 35 parts Kerosene to 1 part Fatty Oil (like a good 46 grade lightweight hydraulic oil) TRA-001A Tool Room Assortment U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 129 Tooling Specialists For The Woodworking Industry Since 1985

DRESSING STICKS

Product Number Shape Size AO412SQ 4 x 1/2" square, Aluminum Oxide AO4121/2RND 4 x 1/2" half-round, Aluminum Oxide AO412RND 4 x 1/2" round, Aluminum Oxide AO412TRI 4 x 1/2" triangle, Aluminum Oxide STK6100 6 x 1 x 1" Square, Coarse, Aluminum Oxide AB-6 6 x 2 x 1" Fine/Coarse, Oil Filled Combination Bench, Aluminum Oxide SB-6 6 x 2 x 1" Fine/Coarse, Oil Filled Combination Bench, Silicon Carbide AB-8 8 x 2 x 1" Fine/Coarse, Oil Filled Combination Bench, Aluminum Oxide SB-8 8 x 2 x 1" Fine/Coarse, Oil Filled Combination Bench, Silicon Carbide TA-334-A Fine 4 x 1/2" x 1/4" Tapered round, Aluminum Oxide TRA-6PC TA-335-A Medium TA-336-A Coarse TA-337-A Fine 4 x 1/2" x 1/4" Tapered triangle, Aluminum Oxide TA-338-A Medium TA-339-A Coarse TA-97- Fine 3 x 5/16 base Tapered Point, Aluminum Oxide TA-98 - Medium Cone 3" long x 5/16" base to tapered point TA-31-AF-Fine 4 x 1 x 1/18" Back Knife Stone, Aluminum Oxide TA-31-AM-Medium TA-296F - Fine 4 x 1 x 1/4" Fine Skiving Stone - Aluminum Oxide TRA-6PC Various 6 piece Tool Room Assort. (6" long Silicon Carbide) TRA-001A Various 13 piece Tool Room Assort. TRA-Ceramic Various 4 piece assortment with leather pouch ceramic Stone size: 1/4" x 5" Knife Deburring and Metal Cleaning Stone TRA-Ceramic Rubber-based abrasive stone designed for removal of steel burrs remaining on the knife after finish grinding. Also excellent for removal of rust on machines or tools.

Product Number Size WEI-100733 60 x 30 x 20mm

Mounted Points Wood Tech offers a wide variety of mounted points in various shapes and sizes. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 130 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

JOINTER STONES “101” For HSS Applications: Hard stones: • 60-120 White Straight Knife (Straight) Wood Tech offers the largest selection of jointer stones in the • 80-400 grit Black Silicon carbide (Straight & Profile) world! After many years of product testing, we have endorsed • 240-400 grit Green Silicon Carbide (Straight & Profile) a select group of products, including the well-known Atlantic products. These stones are accepted world-wide as the “cream of the crop", and are made of high-purity silicon carbide. The Soft stones: • 280-400 grit (Straight Knife Jointing) result is a longer stone life, superior finish, and absence of • 500-600 grit (Profile Jointing) impurities in the product.

Put simply: these stones provide the best possible choice for For Carbide Applications: your applications. Hard Stones: Two basic types of jointer stones (Hard and Soft) are used in • 220 -240 grit Black Silicon Carbide (Profiling) the woodworking industry. In general, hard stones are used on • 240 -400 grit Green Silicon Carbide (Straight & Profile) older machines running at 3,600 RPM’s. Detail to precisely forming the stone is critical, as the stone can “reform" the profile on the knife if mis-made. Soft stones - as used on more Soft Stones: modern 6,000 and higher RPM machines, are more forgiving • 150-220 grit special blended Aluminum Oxide (Profile) and can be “chipped in" to properly fit the knife. Note: harder than the super soft stone, but not quite as hard as the hard stones used for 3600 rpm on HSS. • 240 grit Black Silicon Carbide (Straight) Jointer Stones are similar to grinding wheels in composition. Please refer to: (GRINDING HELPFUL HINTS : WHEELS “101” for more detailed information + on pages 111 and 112.) 1. Jointing actually “dulls” the knives. Don’t over joint your knives!

2. Use a dedicated grinding wheel to form the stone. DO NOT ABRASIVE MATERIALS: use the same wheel to grind knives, as steel chips will be • Silicon Carbide: ( Green) Cuts cooler and faster than Black transferred back to the jointer stone. This will produce “nicking" Silicon Carbide. of your knives. • Silicon Carbide: (Black) Smoother finish, longer life. 3. Finer grits (higher numbers)produce better finishes because • Aluminum oxide : (White, Pink, Orange) Cuts fast and cool, the grains are finer. Coarse grits will remove more steel, and best for Straight Joints on Planers and Moulders. finish results won’t be as smooth.

BONDS: 4. The harder the stone, the more precise the shaping must be. Soft stones can be chipped-in with the actual cutterhead to Vitrified: assure exact counter profile. 1. Easier to shape 2. Cuts cooler 5. Soft stones aren’t designed to remove nicks from knives. 3. Holds the profile better and longer than resin bond. 6. Wax impregnated stones are more forgiving, and the lubricitity helps prevent the stone from being over jointed. Resin: An added benefit is a reduced dust level. 1. More difficult to shape 7. Always be familiar with MSDS for both the stone and the steel 2. Better finish joint being used. Wear appropriate venilation equipment and have 3. More resistant to chip abrasion. proper air transfer to avoid inhalation. 4. Will remove more steel, but must be cleaned and refreshed periodically. 8. IMPORTANT NOTE: As in any jointing stone forming process, use ONLY a wheel to form the stone that has not been GRITS: used to grind ANY knives. Using a grinding wheel that has been in contact with knives will result in small metal particles being Finer grits (higher number) produce better finish quality. impregnated into the jointing stone. This foreign matter will Coarse grit stones will joint up faster and have a longer life. adversely affect the stone performance by nicking the knives. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 131 Tooling Specialists For The Woodworking Industry Since 1985

JOINTING STONE SHAPING INSTRUCTIONS

Note: Grinding accuracy is critical in determining proper jointing slight contact with the knives. Depth control adjustments are stone selection. made while contact is being made. This technique is tricky as extended time of contact can cause the stone to glaze. First, layout the stone using the pattern knife to be jointed. It Jointing Carbide Instructions on Page 106. is most important to maintain as accurate a mirror image fit as possible to the profile being jointed, as the jointing stone will in effect re-profile the knife if not properly formed. Now pre-shape the stone to as accurate a fit as is possible.

Taper the stone on both sides at a 45° angle. This angle allows faster chipping-in of the stone. Insert the stone into the holder on the machine, and chip the stone in for exact fit. The use of only one knife in the chipping-in process results in a better fit. After the stone is chipped-in to fit, start the spindle and bring the stone into the knife at a slow to moderate speed. One technique is to bring the stone in and out in 1 second intervals, making minor adjustments at each interval.

Another technique is to bring the stone in and hold it in

JOINTER STONES RECOMMENDATION CHARTS Hard Jointing Stones Materials Being Type of Joint Abrasive Materials Grit Jointed at 3,600 rpm Planing Profiling Silicon Carbide Aluminum Oxide HSS X X X 80-220 HSS X X 220-400 Carbide Tipped X X 220-400 Carbide Tipped X X 220-400 Carbide Sandwich X X 220-400 Carbide Sandwich X X X 220-400

Soft Jointing Stones Materials Being Type of Joint Abrasive Materials Grit Jointed at 6,000 rpm Planing Profiling Silicon Carbide Aluminum Oxide HSS X X X 280-600 HSS X X 500-600 Carbide Tipped X X 220-400 Carbide Tipped X X 150-220 Carbide Sandwich X X 220-400 Carbide Sandwich X X X 150-600 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 132 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

ATLANTIC JOINTING STONES

These are made in Germany to meet strict specifications for use on Weinig Machinery. Resin and vitrified bonds available. Over 20,000 in stock at all times! We also stock a wide variety of USA made stones for any application. Call for assistance.

Product No. Description Size Grit Color Use SC9600230 SC9-600-075- VUC8 230 x 60 x 15mm 600 Blue/Gray P SC9600G9230 SC9-600-G9-REDM 230 x 60 x 15mm 600 Olive Green P SC9500230 SC9-500-I100- REDCK 230 x 60 x 15mm 600 Brown P SC9600204 SC9-600-075- VUC8 204 x 77 x 15mm 600 Blue/Gray P SC9600G9204 SC9-600-G9-REDM 204 x 77 x 15mm 600 Green P Schleifscheiben SC9600200 SC9-600-075- VUC8 200 x 60 x 15mm 600 Blue/Gray P Honsteine SC9600G9200 SC9-600-G9-REDM 200 x 60 x 15mm 600 Olive Green P SC9600160 SC9-600-075- VUC8 160 x 60 x 15mm 600 Blue/Gray P SC9600G9160 SC9-600-G9-REDM 160 x 60 x 15mm 600 Olive Green P SC9500160 SC9-500-I100- REDCK 160 x 60 x 15mm 500 Brown P SC9400160 SC9-400-02-150-VUK149 160 x 60 x 15mm 400 Blue/Gray S SC950060 SC9-500-3-80- REDCK 60 x 20 x 15mm 500 Brown S SC928060 SC9-280-3-05- VDU4 60 x 20 x 15mm 280 Blue/Gray S

WEINIG JOINTING STONES Made in the USA and Europe These are made to meet strict specifications for use on Weinig Machinery. Other OEM Weinig stones available. Over 10,000 in stock at all times!

Product No. Size and Description Grit Color Use WEI-006-02116 12 x 38mm Round 280 Blue/Grey S WEI-006-01654 60 x 20 x 15mm 240 White S WEI-100724 160 x 60 x 15mm Carbide 600 Blue/Grey P,C WEI-100722 60 x 20 x 15mm Carbide 240 Dark Grey S,C WEI-100731 12x38mm Carbide Round 240 Dark Grey S,C WEI-100721 160 x 60x 15mm 240 Dark Grey P WEI-100728 280 X 60 X 15mm 600 Green HSS,P A150L8V2R 160 x 77 x 15mm 150 White C A220K8V2A 160 x 60 x 15mm 220 White C A220K8V2R 160 x 77 x 15mm 220 White C C220G7V 5/8 x 4 x 8" 220 Black C GC600FV 160 x 60 x 15mm 600 Green P Jointing applications: JS500G8WT 160 x 60 x 15mm 500 Grey P (P) Profile Knives JS-500-G8-WT 160 x 60 x 15mm (wax treated) 500 Grey P (S) Straight Knives RA600-I 1/4 x 3/4 x 3-1/2" 600 Pink S RA600-W 5/8 x 3/4 x 3" 600 Pink S (C) Carbide Knives WEI-100703 12x38mm CBN Tipped Round 180 Red S,HSS WEI-100704 12x38mm Diamond Tipped Round 180 Blue S,C U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 133 Tooling Specialists For The Woodworking Industry Since 1985

JOINTING STONES FOR OTHER MACHINES Made In the USA! Jointing applications: (P) Profile Steel Knives; (S) Straight Knives; (C) Carbide Knives Other sizes & specifications available from stock.

Product No. Description Size Grit Color Use A80M5V2 A-80-M5-V2 3/4 x 3/4 x 4" 80 White S A150L8V2R A-150-L8-V2R 160 x 77 x 15mm 150 Orange C A220K8V2A A-220-K8-V2A 160 x 60 x 15mm 220 White C A220K8V2A 230 A-220-K8-V2A 230 x 60 x 15mm 220 White C A220K8V2A(77) A-220-K8-V2A 160 x 77 x 15mm 220 White C C220G7V C-220-G7-V 5/8" x 4 x 8" 220 Black C C220G8V32-6 C-220-G8-V32 3/4 x 4 x 6" 220 Black P,S C220G8V32-4 C-220-G8-V32 3/4 x 3/4 x 4" 220 Black S C240LV C-240-LV 3/4 x 2 x 8" 240 Black P,S C240LV-S C-240-LV-S 3/8" x 1/4" x 4" 240 Black S C320L8V C-240-L8-V 3/8" x 3/4" x4" 320 Black S C320M3V C-320-M3-V 3/8" x 3/4" 4" 320 Black S GC240LV GC-240-LV 3/4 x 2 x 8" 240 Green P,S GC400M8 GC-400-M8 3/4 x 2 x 8" 400 Green P,C GC400M8S GC-400-M8-S 3/8" x 3/4" x 4" 400 Green S GC400M8-5/8 GC-400-M8-58 5/8" x 3/4" x 4" 400 Green S GC600FV GC-600-FV 160 x 60 x 15mm 600 Green P GC600FV8 GC-600-FV-8 8 x 2 x 3/4" 600 Green P JS16X125 JS-16-125 16 x 125mm S

STRAIGHT KNIFE JOINTER STONES Made In the USA! Other sizes & specifications available from stock

Aluminum Oxide – White, Orange & Others Size 60 Grit 80 Grit 100 Grit 1/4 x 3/4 x 4" JSA60-1/4" JSA80-1/4" JSA100-1/4" 5/16 x 3/4 x 4" JSA60-5/16" JSA80-5/16" JSA100-5/16" 3/8 x 3/4 x 4" JSA60-3/8" JSA80-3/8" JSA100-3/8" 1/2 x 3/4 x 4" JSA60-1/2" JSA80-1/2" JSA100-1/2" 5/8 x 3/4 x 4" JSA60-5/8" JSA80-5/8" JSA100-5/8" Diamond Jointing Tool 3/4 x 3/4 x 4" JSA60-3/4" JSA80-3/4" JSA100-3/4" Part # DIAJTGTL-3/4"

Silicon Carbide (black) Silicon Carbide (green) Size 100 Grit 120 Grit 180 Grit 220 Grit 240 Grit 240 Grit 400 Grit 1/4 x 3/4 x 4" JSC100-1/4" JSC120-1/4" JSC180-1/4" JSC220-1/4" JSC240-1/4" JSGC240-1/4" JSGC400-1/4" 5/16 x 3/4 x 4" JSC100-5/16" JSC120-5/16" JSC180-5/16" JSC220-5/16" JSC240-5/16" JSGC240-5/16" JSGC400-5/16" 3/8 x 3/4 x 4" JSC100-3/8" JSC120-3/8" JSC180-3/8" JSC220-3/8" JSC240-3/8" JSGC240-3/8" JSGC400-3/8" 1/2 x 3/4 x 4" JSC100-1/2" JSC120-1/2" JSC180-1/2" JSC220-1/2" JSC240-1/2" JSGC240-1/2" JSGC400-1/2" 5/8 x 3/4 x 4" JSC100-5/8" JSC120-5/8" JSC180-5/8" JSC220-5/8" JSC240-5/8" JSGC240-5/8" JSGC400-5/8" 3/4 x 3/4 x 4" JSC100-3/4" JSC120-3/4" JSC180-3/4" JSC220-3/4" JSC240-3/4" JSGC240-3/4" JSGC400-3/4" Other sizes available. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 134 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

Cratex Rubberized Abrasives CRATEX is a manufacturer of specialized abrasive products used primarily for metal, glass and lapidary conditioning and finishing. Cratex has been in the business of manufacturing rubberized abrasives for approximately 70 years. These products are abrasive grain mixed homogeneously throughout the rubber so that as the product wears down, sharp new grains are constantly being exposed. This allows products to perform the same from start to finish.

WITH CRATEX, you have the best product for: • Light Deburring and smoothing to relieve stress concentrations and to remove visible and microscopic burrs with out impacting surrounding areas. • Smoothing and polishing to improve wearing qualities and to reduce the dangers of Great for progressive fracture and fatigue failure. De-burring Knives! • Cleaning and polishing to improve performance undesirable surface deposits. • Polishing and smoothing to improve performance, appearance, cleanliness and to lessen the dangers of surface contaminators.

Available in the following grains: Coarse (C) Medium (M) Fine (F) Extra Fine(XF) Green Dark Brown Reddish Brown Grey Green Each Cratex size and shape is made the four standard grit textures or compositions which differ in accordance with the mesh size of the abrasive used.

CRATEX STANDARD BOND - The Cratex bond common to each of the four grit textures is made with premium grade oil-resistant chemical rubber. In contrast to Block and Stick Size Chart conventional grinding wheels, the Cratex bond has unique cushioned action…cuts freely, smoothly and softly without gouging or digging in to the work surface. It resists clogging or smearing and is ideal for a broad range of applications where metallic or non-metallic surfaces must be smoothed and polished without loss of dimensional tolerances or control.

CRATEX Blocks and Dressing Sticks for Touching Up Knives Cratex Blocks and Sticks are excellent hand tools for cleaning and polishing metal surfaces, for breaking edges, smoothing away high spots, removing rust, heat marks, tarnish and stains. Designed for either manual or mechanical operation, they can be mounted in tool holding fixtures, chucks, or cradles. Use them for polishing shafts, de- burring knives, cleaning and dressing diamond wheels, polishing rotating cylindrical parts, cleaning calibration reference points, removing feather edges, touching up cutting tools, dies, chisels and other sharp edged tools. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 135 Tooling Specialists For The Woodworking Industry Since 1985

Cratex Straight Wheels Cratex Large Wheels have found wide application for removing rust, heat marks, tarnish, excess solder, scratches, corrosion...blending in and polishing welded seams after rough grinding...polishing bearing surfaces and race ways...removing burrs and breaking edges...smoothing and polishing castings and punched or sheared pieces...wet sanding of gem stones...trimming plastic articles...smoothing glass edges...cleaning before welding or soldering...and for countless other deburring, smoothing, and polishing operations.

CRATEX 80 Piece Introductory Kit Please see our Web Site for Kit No. 777 contains 80 wheels and points plus four Madrels. Packaged in a four complete listing of block and compartment plastic box by grit textures C, M, F, & XF for easy selection. Ideal for us wheel sizes. in a wide range of polishing, smoothing and deburring applications. Click on the links above to learn more about Cratex blocks, dressing sticks and wheels.

Part No# Descriptions Dimensions Cratex#777 Introductory set containing: 8 tapered Edge Wheels, No. 2 5/8" dia 16 Strt Wheels, No. 74 7/8" dia. x 7/8" thick 8 Straight Wheels, No. 86 1" dia. x 3/16" thick 16 Cylinder Points, No. 6 7/8" long x 1/4" dia. 16 Bullet Points, No. 8 1" long x 9/32" dia. 8 Bullet Points, No. 10 5/8" long x 3/8" dia. 2 Wheel Mandrels, No. 3 1/8" shank 2 Point Mandrels, No. 4 1/8" shank Components are available for sale individually. Equally assorted in four Cratex grit textures C, M, F, XF See our website or Cratex 64 Piece Point Test Kit call us for details. Kit No. 778 contains two each of all eight Cratex Point Shapes equally assorted in four grit textures for a total of 64 points plus two No. 4 and two No. 6 Point Mandrels. Ideal for deburring, smoothing and polishing hard to reach surfaces. Click on the links above to learn more about Cratex blocks and dressing sticks

Part No# Descriptions Dimensions Cratex#778 Set contains: 8 Cylinder Points, No. 4 1/2" long x 1/4" dia. 8 Cylinder Points, No. 6 7/8" long x 1/4" dia. 8 Cylinder Points, No. 8 1" long x 9/32" dia. 8 Cylinder Points, No.10 5/8" long x 3/8" dia. 8 Cylinder Points, No. 11 1" long x 3/8" dia. 8 Cylinder Points, No. 12 7/8" long x 3/8 to 5/16" dia. 8 Cylinder Points, No. 14 7/8" long x 5/8 to 1/8" dia. 8 Cylinder Points, No. 15 7/8" long x 1/2" dia. 2 Point Mandrels, No. 4 1/8" shank 2 Point Mandrels, No. 5 1/8" shank Equally assorted in four Cratex grit textures C, M, F, XF U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 136 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

EZE-LAP Hones DIAMOND SHARPENERS EZE-LAP Diamond Hones Complete your tool sharpening with these versatile diamond hones. Perfect for honing out nicks on the edge of tools, these diamond hones can also be used to sharpen car- bide table saw blades, router bits, and planer knives. Each hone has a diamond surface that measures 3/4" x 2": mounted on a 6" long plastic handle.

We offer EZE-LAP hones Product # Description Grit in the following grits: EZE LAP LC EZE Lap Diamond Hone Coarse, LF 6" long with 250 (2 x 3/4") diamond section - Black Handle Coarse (250 grit) for faster EZE LAP LM EZE Lap Diamond Hone Med., LF 6" long with (2 x 400 removal of metal and shaping, 3/4") diamond section - Purple Handle Medium (400 grit) for deburring & Fine (600 grit) used for honing EZE LAP LF EZE Lap Diamond Hone, Fine, LM 6" long with (2 x 600 to achieve a keen razor edge on 3/4") diamond section - Red Handle your tools. EZE LAP LSF EZE Lap Diamond Hone Super Fine, LF 6" long 1200 with (2 x 3/4") diamond section - Blue Handle

! See our Website for NEW EZE-LAP & DMT Products ! DMT Diamond Sharpeners This is a wonderful invention and the perfect tool for honing an edge on carbide & HSS knives. The blade of each DMT Diafold Sharpener measures 1" wide by 4" long and is covered with monocrystalline diamonds bonded in nickel to a steel mesh. The Choose from holes in the mesh provide clearance for the metal shavings and keep the sharpener from clogging during use. This design assures that the cutting surface will stay flat FIVE different grits providing consistent results. The plastic handle is designed to fold up into a carrying of DMT Products: case to protect the sharpener when not in use and to make transporting easier. Extra Coarse (200 grit) - Black: For aggressive removal of metal on The diamonds used in all DMT products do not break apart like some other manu- damaged tools. facturers, ensuring very long life. The Diafold Hones should be used with water as a lubricant for the best possible results. The DMT Sharpeners can also be used on Coarse (325 grit) - Blue: Rapidly carbide products like BAK-PAK®, carbide inlay knives, carbide saw blades and router hones cutting tools or restores an bits, and tipped shaper cutters. edge on a tool or blade. Fine (600 grit) - Red: Ideal for putting razor sharp edge on a blade that is regularly maintained. Extra Fine (1200 grit) - Green: Polishes and refines the edges of fine knives and precision tools.

Ceramic (2200 grit) - White: Provides the finest polished edge of all bonded abrasives.

This section of DMT represents only a small portion of Diamond Sharpeners and products available. Call us with your specific needs or visit our website for a complete listing of Diamond Sharpeners and sharpening instructions. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 137 Tooling Specialists For The Woodworking Industry Since 1985

DMT Diafold Sharpeners Folding plastic handles enclose the 4” (110m) Diamond Whetstone™ sharpener. 9-1/2” (240mm) open. 5” (125mm) closed. Available in single and dual grits.

Product # Description Grit DMT-FWE 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone Extra Fine DMT-FWF 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone Fine DMT-FWC 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone Coarse DIAFOLD Sharpeners DMT-FWX 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone Extra Coarse DMT-CFWE 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone Ceramic/XFine DMT-FWEF 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone XFine/Fine DMT-FWFC 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone Fine/Coarse DMT-FWCX 4-1/3" x 7/8" x 3/16" Diafold Diamond Whetstone Coarse/X Coarse

DMT Diamond Diafold Tapered Rods and Flat Files Folding plastic handles enclose the diamond surface and provide storage for the 4" (110m) pocket diamond files. 9-1/2" (240mm) open and 5" (125mm) closed. The handle folds into a protective sheath like the Diafold hones carrying case. Tapered Rod DMT Diafold Tapered Rods

This tapered rod is coated with the high quality diamonds. It is perfect for removing the burrs on knives. The Diafold Tapered Rod is useful for touching up the bevel on hook tools and can be used on serrated knifes in the kitchen. The 4" long rod tapers from 1/16" diameter at the small end to 1/4" diameter on the larger end. Item # Description Grit DMT-FSKE 1/16" to 1/4" taper, Serrated Knife and Conical File Extra Fine DMT-FSKF 1/16" to 1/4" taper, Serrated Knife and Conical File Fine DMT-FSKC 1/16" to 1/4" taper, Serrated Knife and Conical File Coarse DMT Diafold Flat Files One sided diamond file for narrow, confined applications. 3/4" base to 1/4" taper. Folding plastic handles enclose the diamond surface in storage for 4" (110.9 mm) pocket diamond file. 9 1/2" (240 mm) open, 5" (125 mm) closed. Item # Description Grit DMT-FFF 3/4" base to 1/4" taper, Flat File with diamond on Fine one side for narrow, confined application. DMT-FFC 3/4" base to 1/4" taper, Flat File with diamond on Coarse one side for narrow, confined application. Flat File DMT-FFX 3/4" base to 1/4" taper, Flat File with diamond on Extra Coarse one side for narrow, confined application. DMT Diamond Mini Sharpeners Mini Diamond Sharpeners come with a flip open lid/handle. Swivel ring for key chain. 5-1/2” (140mm) when open.

Item # Description Grit DMT-F70E 2-11/16" x 15/16" x 3/16" Diamond Mini-Sharp Extra Fine DMT-F70F 2-11/16" x 15/16" x 3/16" Diamond Mini-Sharp Fine DMT-F70C 2-11/16" x 15/16" x 3/16" Diamond Mini-Sharp Coarse Mini Sharpeners DMT-F70X 2-11/16" x 15/16" x 3/16" Diamond Mini-Sharp Extra Coarse U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 138 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

DMT Honing Cones Tapered diamond slip stones. Excellent for woodworking gouges, dental tools, gunsmithing, woodturning, tool & die work, and more.

Item # Description Grit DMT-DCSFH Small, 1/8" to 3/8" diameter x 4" cone (3.2mm Fine to 9.5mm) with 4" (102mm) handle. DMT-DCMF Medium, 3/8" to 3/4" diameter x 6" cone Fine (9.5mm to 19.1mm x 152mm) half round. DMT-DCKF DMT-DCLF Large, 3/4" to 1-1/4" diameter x 8" cone Fine (19.1mm to 31.8mm x 203mm) half round. DMT-DCKF All three sizes in hardwood storage package. Fine

DMT Whetstone Pocket Models Versatile pocket models can be used to sharpen, hone or file any hard material.

Item # Description Grit DMT-WME 4-1/3"x 7/8"x3/16" - 4" Diamond Whetstone with Extra Fine leather sheath. DMT-WMF 4-1/3"x 7/8"x3/16" - 4" Diamond Whetstone with Fine leather sheath. DMT-WMC 4-1/3"x 7/8"x3/16" - 4" Diamond Whetstone with Coarse leather sheath.

DMT – WMC DMT Whetstone Bench Models -6" or 8" models

For shop bench or kitchen counter, these models offer large and wide surfaces of diamond for all sizes and types of knives and tools. Furnished with hardwood case and non-skid rubber feet. 8" models have additional mounting tabs.

Item # Description Grit DMT-W6E 6"x 2"x3/4" - 6" Diamond Whetstone Extra Fine DMT-W6F 6"x 2"x3/4" - 6" Diamond Whetstone Fine DMT-W6C 6"x 2"x3/4" - 6" Diamond Whetstone Coarse DMT-W6X 6"x 2"x3/4" - 6" Diamond Whetstone Extra Coarse DMT-W8F 8"x 2-5/8"x1-1/4" - 8 “ Diamond Whetstone Fine DMT-W8C 8"x 2-5/8"x1-1/4" - 8 “ Diamond Whetstone Coarse Bench Model

DMT DuoSharp® Bench Models – 8" models

Innovative large surfaced precision-flat, two-grit diamond sharpeners are perfects for woodworkers and other applications that demand the ultimate in flatness, multiple grits and large work surfaces. Comes with a non-skid mat.

Item # Description Grits DMT-W8EFNB 8"x 2-5/8"x3/8" - 8" Diamond Benchstone Extra Fine/ Base Fine Stone DMT-W8FCNB 8"x 2-5/8"x3/8" - 8" Diamond Benchstone Fine/Coarse DMT-B8250 12" Molded base for mounting your stone N/A U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 139 Tooling Specialists For The Woodworking Industry Since 1985

NEW! DMT CERAMIC SHARPENERS Now, DMT® adds a new dimension to their sharpening systems with the introduction of an assortment of precision engineered, unbreakable ceramic and diamond-ceramic sharpeners. DMT’s new line incorporates the patented CeraFuse™ process to transform the surface of aluminum to an extremely hard, dense aluminum oxide that has the same properties of solid ceramic materials. The new ceramic and diamond- ceramic sharpeners are unbreakable, light, fast to use, wear resistant, will not rust and need no lubricant for the sharpening process. These ceramic and diamond-ceramic sharpeners provide the ultimate in edge polish. DMT® is offering this breakthrough Ceramic Sharpeners technology in four models to tackle a multitude of sharpening tasks. The #CFSK Diafold Ceramic Serrated Knife Sharpener was developed from the • Unbreakable famous DMT® Diafold® diamond sharpener models that have become part of • Made in the U.S.A.! everyman’s cutlery maintenance program. The ceramic version offers a 4.43" cone- • Versatile shaped sharpener and DMT’s practical, self-stowing, folding design. It is remarkably • Compact design light—only 1 ounce. • Light weight A great addition to the collection is the #CDT62 Diamond-Ceramic Triangle • Will not rust Sharpener featuring a 25 micron Diamond Flexi-Sharp® surface that is just one • Multi-task sharpeners facet of a triangle of sharpening surfaces. This sharpener also offers the utility of 3 • No lubricant needed different radiused sharpening edges and a groove for fishhooks. It adapts to virtually any sharpening task presented by woodworking gouges, serrated knives or shaped tools.

DMT CDT62 - Triangle 6 in 1 Tool This sharpener also offers the utility of 3 different radiused sharpening edges and a groove for fishhooks.

Item # Description Grit DMT-CDT62 Diamond Ceramic Triangle 6 in 1 tool: Handle: 4-1/16" Coarse/Fine (119 mm) Flat sides: 6" (152 mm) Radii: 0.063" (1.60 mm) 0.125" (3.18 mm) 0.188" (4.78 mm

Ceramic Triangle Tool (Chisels not included) Diafold Knife Sharpeners

Item # Description DMT-CFSK Diafold® ceramic serrated knife sharpener hones small gouges and fixed or folding knives. 4" ceramic rod, 9 1/2" (240 mm) open, 5" (125 mm) closed. DMT-CFWE NEW! 4-1/3” x 7/8” x 1/4” Double Sided Diafold with Extra Fine Grit on one side, ceramic on the other Ceramic Diafold Sharpener

DMT Dia-Paste™ Diamond Compound Use to obtain a highly polished or mirror finish on fine woodworking tools like chisels and plane irons. Packaged in an easy-to-use 5 gram syringe.

Item # Description DMT-DP6 6 micron, copper color DMT-DP3 3 micron, green/yellow color DMT-DP1 1 micron, light gray color Dia-Paste™ Compound DMT-DPK Kit of 3 Dia-Paste tubes (Includes: DP1, DP3 & DP6) U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 140 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

DMT Dia-Sharp® Mini-Hone Dia-Sharp® Mini-Hone™ — 2.5" diamond surface with Easy Access Tip which measures .033" thick. Color-coded ergonomic handle eases sharpening, deburring and honing in tight spaces. 4 1/2" x 3/4" 114.3 mm x 19 mm, SURFACE: 2 1/2" x 3/4" 63.5 mm x 19 mm. WINNER OF THE 2002 BLADE AWARD!

Item # Description Grit DMT-D2C Dia-Sharp®Mini-Hone™ Coarse Mini-Hones DMT-D2F Dia-Sharp®Mini-Hone™ Fine DMT-D2E Dia-Sharp®Mini-Hone™ Extra-Fine DMT D2K- KIT OF 3 MINI-HONES WINNER OF THE 2003 PRACTICAL INNOVATION AWARD! - As the only American firm to be so honored at the Internation Hardware Fair in Cologne, DMT’s Diamond Mini-Hone™ continues to be recognized globally for its unique, ergonomically- efficient design. The Mini-Hone is considered one of the most user-friendly sharpening devices available today.

Item # Description DMT-D2K The Diamond Mini-Hone kit offers three tools with color coded handles for easy grit identification to handle all sharpening needs: such as mold and die work, scissors and metal snips and pruners and knives.

DMT D3C - Dia-Sharp Credit Card Sized Sharpener Ready-to-go 3" credit card size diamond sharpener with convenient vinyl color-coded carrying case. Fits easily in pocket or wallet.

Item # Description Grit DMT-D3C 3-1/4" x 2" x .05" 83 mm x 51 mm x 1 mm Coarse DMT-D3F 3-1/4" x 2" x .05" 83 mm x 51 mm x 1 mm Fine DMT-D3E 3-1/4" x 2" x .05" 83 mm x 51 mm x 1 mm Extra-Fine DMT 4" & 6" DIA-SHARP SHARPENING STONES Dia-Sharp® Sharpening stones have the name of the grit marked clearly on the side of Credit Card Size the stone for quick identification. Available in two sizes - 4 and 6 inches. The six inch stone includes non-skid rubber feet.

Item # Description Grit DMT-D4C 4" sharpening stone, 4" x 7/8" x 3/16" 102 mm x 22 Coarse mm x 5 mm DMT-D4F 4" sharpening stone, 4" x 7/8" x 3/16" 102 mm x 22 Fine mm x 5 mm DMT-D4E 4" sharpening stone, 4" x 7/8" x 3/16" 102 mm x 22 Extra-Fine mm x 5 mm DMT-D6C 6" sharpening stone, 6" x 2" x 1/4" 152 mm x 51 mm x Coarse 6 mm with non-skid rubber feet Four Inch Stones DMT-D6F 6" sharpening stone, 6" x 2" x 1/4" 152 mm x 51 mm x Fine 6 mm with non-skid rubber feet DMT-D6E 6" sharpening stone, 6" x 2" x 1/4" 152 mm x 51 mm x Extra-Fine 6 mm with non-skid rubber feet U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 141 Tooling Specialists For The Woodworking Industry Since 1985

WHAT DO YOU WANT TO SHARPEN?

A Helping We suggest the following DMT Sharpeners. See our website Hand or call us for complete step-by-step instructions on these and other items you may wish to sharpen. We have thousands of + sharpeners in stock!

CIRCULAR SAWS: ROUTER BITS: KNIVES: Single Grit Diafold (CARBIDE & TOOL STEEL) 6" or 8" Whetstone Bench stones Flat Files 6" or 8" DMT Whetstone Bench Models Single Grit Diafold Recommended Grits: Single Grit Diafold Sharpeners Recommended Grit: FINE to maintain a blade or COARSE Double Sided Diafold Sharpeners COARSE to restore a damaged edge. to restore a damaged tooth tip. Recommended Grit: EXTRA COARSE to remove FINE to maintain a bit or COARSE to damaged areas restore a damaged edge. EXTRA FINE for a polished edge

SERRATED KNIVES: FLAT WOOD DRILL BITS: FORSTNER BITS: Mini-Steel DMT Diafold Sharpeners - Single Grit DMT Diafold Sharpeners - Single Grit Diafold Ceramic Serrated DMT Diafold Sharpeners - Double Grit DMT Diafold Sharpeners - Double Grit Knife Sharpener DMT Diamond Diafold Flat file DMT Diamond Diafold Flat file Recommended Grits: DMT Dia-Sharp Mini-Hone DMT Dia-Sharp Mini-Hone COARSE to restore a damaged edge. EXTRA COARSE for removing damaged areas. CHISEL & PLANE IRON: CARVING TOOLS: EXTRA FINE for a polished edge. 6" or 8" Whetstone Bench Stone DMT Diafold Serrated Knife Sharpener 8" Duo-Sharp Bench Stone DMT Diafold Sharpeners - Double Grit DMT CS2 - Ceramic Steel Triangle GOUGES: Recommended Grit: DMT Dia-Sharp Kit of 3 Mini-Hones IN-CANNEL: COARSE to restore a damaged edge. DMT Diamond Mini Sharpeners DMT Ceramic & Diamond EXTRA COARSE to remove damaged DMT Diafold Sharpeners - Single Grit Honing Cones. areas DMT Diafold Serrated Knife Sharpener FINE to maintain a bit EXTRA FINE for a polished edge PRUNERS: OUT-CANNEL: DMT Whetstone Bench Models Mini-Sharp DMT Duo-Sharp Bench Stones Single Grit Diafold Flat File V-GOUGE: DRAW KNIVES: DMT Ceramic & Diamond Recommended Grits: DMT Diamond Honing Cones Honing Cones. COARSE to restore a damaged edge. DMT CS2 - Ceramic Steel Triangle FINE to maintain a bit.

SCISSORS: Mini-Sharpeners Single Grit Diafold Double Grit Diafold CHAIN SAWS: Recommended Grits: DMT-FCS5C Chain Saw File — 5/32" (4.0 mm) Coarse COARSE to restore a damaged edge. DMT-FCS6C Chain Saw File — 6/32" (4.8 mm) Coarse EXTRA FINE for a polished edge DMT-FCS7C Chain Saw File — 7/32" (5.5 mm) Coarse U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 142 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

BARDO SANDING WHEELS

The Profile Sanding Experts! Bardo Abrasives began manufacturing shapeable sanding wheels in 1978. The BDX Woodworking Wheel was the initial Bardo Flex Shapeable sanding wheel offered. New technology and research have played a major role in the development of a full line of different wheels for a wide range of applications. Wood Tech is pleased to offer these fine products to you. If you have any questions, please send us an email or call our toll-free number listed at the top of the page.

SHAPEABLE SANDING WHEELS FOR SMOOTH FINISHES, FREE FROM SCRATCHES. . .Remove chattermarks, sand-end grain, sealer sand and defuzz wood faster and cleaner than ever before!

BARDO FLEX DEBB WHEELS for sanding Raised Panel Doors

You will not believe your eyes!!

Sands and finishes raised panel doors and outer door edges like you have never seen before!! Now You Can Easily Sand Raised Panel Doors! • Made with all new non-woven abrasive technology & special bonding agents. • Sands end-grain more aggressively than any product you have ever seen! • No more time consuming setup times to prepare wheels to sand. • No more stocking 25 different expensive wheel configurations. • No more inexperienced operators running wheels in the wrong direction. • No more customer complaints about wild or inconsistent scratches on the surface!

BARDO FLEX DEBB WHEELS can be run in either direction! No operator confu- sion! You can sand on the face width of the wheel or the side of the wheel! As a mat- ter of fact, we encourage you to tilt the wheel at a 45 degree angle to the part, so that you are partly coming down on the wood and partly coming in from the side!

You will notice that Bardo Flex DEBB wheels never become firmer as you get closer to the core like other sanding wheel products and you will receive a uniform finish A Helping DEBB WHEELS from piece to piece, much better than you ever could with a sandpaper product! They Hand shape easily and are so forgiving that they follow the contour exactly, AND hold their SHAPING shape! + INSTRUCTIONS • Use either 60 grit or 80 grit Contact us to see how these wheels can work for YOU on verticle spindle sanders and FLEXIBLE CLOTH BACKED double-end tenenors, what speeds are recommended, what sizes & grits are available sandpaper glued to a waste piece of and shaping suggestions! moulding. • Tuck sandpaper into all the profiled WHEEL SIZE SPECIFICATIONS WHEEL SIZE SPECIFICATIONS areas of the moulding. This is why the cloth backed sandpaper needs 6 x 1 x 1-1/4" AM-344-3 (Aluminum 8 x 1 x 1-1/4" AM-344-3 Oxide Medium Grit) to be flexible. Regular paper backed sandpaper WILL NOT WORK because 6 x 1 x 1-1/4" AF-344-5 (Aluminum 8 x 1 x 1-1/4" AF-344-5 the sanding wheel will burn right Oxide Fine Grit) through it. 6 x 1-1/2 x 1-1/4" AM-344-4 8 x 2 x 1-1/4" AM-344-6 • Running the part past the wheel at 6 x 1-1/2 x 1-1/4" AF-344-8 8 x 2 x 1-1/4" AF-344-10 1700 rpms will “burn” the shape in just 6 x 2 x 1-1/4" AM-344-6 a few minutes. 6 x 2 x 1-1/4" AF-344-10 U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 143 Tooling Specialists For The Woodworking Industry Since 1985

A Helping RPM & Feed Speed DEBB WHEELS USAGE RECOMMENDATIONS Hand Recommendations Single sanding station tenenor, or a vertical spindle sander + (i.e. Whirlwind, Larick, Unique, etc.) Wheels sand best when run between 600 rpms and 1200 rpms, with 600 rpms the • Use a MEDIUM grit DEBB wheel. BEST STARTING POINT. However, • Tilting the wheel at a 45 degree angle to the part is ideal if your machinery allows 1200 rpms is quite acceptable for these for it. This will allow you to attack the board coming IN from the side, as well as, wheels. coming DOWN on the board. You will be using both the side of the wheel and the outside edge. FEED SPEEDS: on the double-end tenoners can very according to whether Two station sanding tenenor you are sanding WITH the grain or • The first station should have a MEDIUM grit DEBB ACROSS the grain or outside profiles or wheel rotating the wheel INTO the direction of the feed. raised panels. • The second station should have a FINE grit DEBB YIELD: 30,000 lineal feet average max. wheel rotating WITH the direction of feed.

OUTSIDE 50 FPM 35 FPM NOTE: For consistent finish on verticle spindle sanders, EDGES (feet per minute) across it would be best to have a power feeder for consistent with grain grain feed speed and pressure. RAISED 44 FPM 28 FPM NEW! - Bardo Impregnated Flapwheels PANELS with grain across grain • Fast “burn” in, or take shape to the moulding being sanded. • Incredibly wide variety of options. General rules: • Aluminum Oxide is the grain to use when looking for sanding action on raw board • Silicon Carbide is the grain to use for finishing and after sealer, stain or primer. There are exceptions, but this is a good GENERAL rule of thumb. You will find that these wheels have the feel of a solid wheel, yet posses the qualities of a conformable non-woven abrasive flapwheel! Based on the type of board you are sanding, what type of sanding you are doing and the degree of sanding to be done, in the standard 8” OD x 3” ID in a variety of width sizes you may choose: Profile Sanding Made Easy! The feel of a solid wheel with D Treat Recommendations: qualities of non-woven flapwheels • Use after stain, sealer or primer has been applied to MDF or natural wood! • Several large bass shutter & louver, as well as moulding manufacturers – use 8" OD Note: 2" DEBB wheels can be x 3" ID in a variety of widths Green VFN HD D Trt. and Silicon Carbide Very Fine flipped over for 2nd sanding MD D Trt. for both light sand on raw and seal sand. pattern to maximum use. • Green Very Fine or Silicon Carbide Very Fine

Machine, Grit, RPM and Forming C6 Treat Recommendations: Recommendations: • Aggressive wheel – ideal for scuffing a hard coat of UV on MDF between coats. • Use of a variable speed shaper and • Large MDF moulding manufacturer uses a variety of these wheels on raw MDF for power feeder is highly recommended. presand prior to white primer. They use Alox FN HD C6 Trt. or Alox VFN MD C6 • 600 to 1200 RPM Max. (higher RPM will Trt., according to the condition of the surface. Alox Med HD C6 Trt. in 8" OD x 3/4" may be ineffective.) wide x 3" ID is used on the sides of the mouldings successfully. • Use a medium grit wheel to achieve a • Aluminum Oxide Very Fine, Fine or Medium 120 to 150 grit end finish result. • Silicon Carbide Fine or Medium • Use a fine grit wheel to achieve a 180 to 220 grit end finish result. Bardo can create a wheel to meet special applications. • To form your DEBB wheel, glue 60 grit cloth-backed flexable sandpaper to your Due of the large number of applications this product can be used for, we recommend moulding and burn-in your profile. We that you call one of our Wood Tech’s technical specialists to help match the product to suggest you burn in at lower speeds. your usage. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 144 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

Bardo Flex Flapwheels • Flexible, very conformable wheels made with non-woven abrasive material. • Silicon Carbide fine, very fine and super fine provide better finish than Aluminum Oxide (Red) Finishing Flap Brushes after stain or sealer has been applied. • Use Aluminum Oxide Medium Grit size flapwheels on raw mouldings when cutter blades are in good condition.

Bardo Flex White Flapwheels • Least expensive wheels we manufacture. • Made from NON-ABRASIVE material • Acts more as a wipe-off rather than a sanding wheel. • Excellent on antique finishes. • Perfect for the last head of multi-head sanders for cleaning off moulding. Bardo Flex Flapwheels

Bardo Flex Interleafs • Excellent multi-purpose LIGHT, FINISH sanding wheels. • Made with soft, white sandpaper between non-woven abrasive material. • Removes light knife marks on raw mouldings even with coarse 80 grit. • BEST at preparing a surface to accept sealer, stain or primer. • Hardwood mouldings like oak for raw board light sanding in 80 and 120 grit. • Raw wood sanding on poplar, bass, cedar, mahogany and MDF moulding use 180 grit AFTER knife marks have been removed by Bardo Flex Blend/Finish #SF-12. • MDF reccommendations: 220 and 320 grit between sealer coats, 200 grit is commonly used to sand after primer on MDF.

Bardo Flex White Interleafs • Low cost buffing wheel • Available with soft, white 180 or 220 grit sandpaper. • Acts FINER than our regular 320 grit. • Wonderful buffed finishes are produced after white primer on MDF. • Use after stain on poplar or bass louvers and shutters. Bardo Flex Interleafs U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 145 Tooling Specialists For The Woodworking Industry Since 1985

Bardo Flex Blend/Finish Wheels Bardo Flex Blend/Finish Wheels are soft spongy wheels that are used when knife marks are put in mouldings during shaping operations that are too deep for Bardo Flex Interleafs.

• Ideally suited for raw moulding sanding because of their cushion and cutting ability. • Machine settings do not have to be perfect as they do with sand belts and harder sanding wheels. • On poplar, bass, and MDF surfaces spec #SF-12 cleans up mill marks. • Sanding head spin INTO the direction of the feed. • Makes removing knife marks easier and faster. • Increase the sanding ability by slowing down your feed rate.

#SF-12 may also be used on a vertical spindle sander to do raw MDF surfaces for parts like an oval mirror frame or table tops. Spec #SM-12 is used very successfully Bardo Flex Blend/Finish Wheels for stripping finished parts to the bare surface for re-work. When a small OD (3-1/2" to 4") is required to get inside to do a 120 grit raw wood sand, spec #AC-12-1140 is an excellent choice. Bardo Flex Sanding Wheels • Heavier degree of sanding on hard boards. • Removes knife marks quicker and more completely than Blend/Finish wheels.

Spec #AM-00 provides 120-150 grit sanding ability when sanding mill marks off immediately following shaping on oak, cherry, and other hard mouldings. This versatile spec is also used on vertical spindles on the outer door edges, WHEN SANDING PREDOMINANTLY WITH THE GRAIN. Excellent for case goods and beveled (eased) edges on furniture frames. Spec #SSF-00 is used very successfully on quality MDF mouldings after white primer for a smoother glossy finish. Bardo Flex Woodworking Wheels • GARNET is the abrasive grain. Bardo Flex Sanding Wheels • Hardest sanding wheels that we offer. • Comparable with 3M‚s DLG Finishing, Carborundum’s Carbo-Cut and Norton’s Polybond wheels. • Used ONLY for removing knife marks on very hard moulding such as ASH, HARD MAPLE, ASPEN and HICKORY.

Some people prefer using WOODWORKING wheels on the first sanding head when working on MDF moulding with Garnet JL Density 120 grit. Ash requires 40 grit on the first pass and 80 grit on the second pass, whereas hard maple usually only requires 60 grit on the initial sand. For people sanding raised door panels that have either end or cross grain on double-end tenenors, this wheel in Garnet HD 40 grit is used. The wheel is run between 800-1100 RPMs and they use 40 grit for the “climb cut.” If they have two sanding stations they use Garnet HD 80 grit for the “finish sand.”

Bardo Flex Woodworking Wheels U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 146 Website: www.woodtechtooling.com • Email: [email protected] Tooling Specialists For The Woodworking Industry Since 1985

Bardo Flex Shapeable Sanding Wheel Recommended Starting Points Sanding raw poplar, bass, MDF, pine, cedar, mahogany mouldings & slats: To remove knife marks: Blend/Finish Spec #SF-12 To prep for stain: Interleaf 180 grit If knife marks are not fully removed, next step is: Blend/Finish Spec #AF-12 If too aggressive on bass, use: Interleaf 320 grit Sanding raw oak and cherry mouldings, case goods and furniture frames: To remove knife marks: Sanding Spec. #AM-00 To prep for stain: Interleaf 120 grit Bardo Flex Sanding Wheel If knife marks are not fully removed, next step is: Woodworking (3"ID) Garnet Shaping Instructions JL 40 grit Sanding raw ash, hard maple, hickory mouldings Materials Needed: Twelve inch hardwood moulding with To remove knife marks: Woodworking Garnet HD 40 grit (ash), Woodworking shape desired to sand with mitre saw Garnet HD 60 grit (hard maple) cuts every 1" or less. (see photo) To prep for stain: Woodworking Garnet HD 80 grit Sample Procedure: Most to Least Agressive “Buffing" Wheels for Between Coats If you do nothing at all, Bardo Flex shapeable sanding wheels will take all #1 Interleaf 220 grit After water-based primer on MDF the shape of the moulding by exerting #2 Interleaf 320 grit Generally good on natural boards pressure (even excessive) down on the #3 Sanding Spec. #SSF-00 After white primer on quality MDF moulding. The harder the wheel style, #4 Flapwheel Sic SFN MD Good on solvent based primers/stains the longer it will take to conform. You can expedite this process by taking #5 Interleaf White 180 & 220 Excellent finish, low-cost on MDF your 12" piece of hardwood with cuts #6 Flapwheel White Type-T HD Only wipe-off or antiquing in it and running it underneath the rotating wheel USING EXCESSIVE Bardo Flex Shapeable Sanding Wheel Availability Chart PRESSURE. You can burn this piece because it will be a piece of waste Product Abrasive Grit Size Dia. (ID) Width Density wood. After the wheel has taken shape, Bardo Flex SIC 80,120,180, 220, 6" (2")* 1/2"- 27" HD raise the head so that MINIMAL Interleafs 320 8" (3") pressure is used to get the finish in Bardo Flex White Type-T 180, 220 8" (3") 1/2"- 27" HD production. This will maximize product Interleafs life. Bardo Flex Sic, Alox SFN, VFN, FN, 6" (2")* 1/2"- 27" LD, MD, Flapwheels MED, CRS 8" (3") HD Bardo Flex White Type-T NON-ABRASIVE 8" (3") 1/2"- 27" HD Flapwheels Bardo Flex Sic, Alox SFN, VFN, FN, 4" (1") 1/2"- 14" HD A Helping Blend/Finish MED CRS 6" (1-1/4") + Hand 8" (1-1/4") When looking for more 8" (3") sanding removal, rotate Bardo Flex Sic, Alox SFN, VFN, FN, 6" (1-1/4") 1/2"- 20" LD aluminum oxide wheel into Sanding MED, CRS 8" (1-1/4") direction of feed. 8" (3") When finishing - always Bardo Flex Garnet, 40, 60, 80, 120 6" (1-1/4") 1/2"- 10" JL, RD, use silicon carbide wheel. Woodworking Sic 8" (1-1/4") HD 8" (3") 10" (5") Bushings Available - 1/2", 5/8" 3/4", 1 1/4", 1-1/2" *Wheels with 2" ID’s only available with 1-1/4" bushings. U.S Toll Free: 1 800-TOOLING (866-5464) • 1 (828) 628-4414 • Fax: 1 (828) 628-4490 Website: www.woodtechtooling.com • Email: [email protected] 147 Tooling Specialists For The Woodworking Industry Since 1985

Bardo Flex Saw Polishing Wheels Bardo Flex Saw Polishing Wheels are polyurethane foamed wheels that are impregnated with either Aluminum Oxide or Silicon Carbide abrasive grain. They are available in 24, 40, 54 grit size in 6", 8", or 10" OD’s for both applying satin finishes to carbon steel circular saw blade faces and re-facing of saw blade faces. These are generally used on machinery where the circular saw blade spins on a table as the wheel is presented to the saw blade face, as it spins on a fixture, the wheel traverses across the blade either from the center hole towards to sand blasted finish at the edge, or from the outer edge to the center hole. Bardo Flex saw polishing wheels are absolutely BEST USED IN WET OPERATIONS. They have successfully replaced 3M DBX Finishing, Artifex and Carbo-cut saw Bardo Flex Saw finishing wheels. Polishing Wheels

Availabilty Chart for Saw Polishing Wheels

SIZES WIDTHS 6 x 1 x 1-1/4", 8 x 1 x 1-1/4", 10 x 1 x 1-1/4" 1-1/2" and 2" widths available

SPECS FOR REFINISHERS Alox LD 40 grit and Alox LD 54 grit

SPECS FOR MANUFACTURERS Sic HD 40 grit (replaces Artifex 46 grit) Alox HD 24 grit (replaces 3M DBX finishing and is the most aggressive, long lasting saw polishing wheel.

Bushings available to 20mm and 1".

SANDCLEAN™ – Sanding Belt Cleaning Sticks Erase pitch and sawdust from sanding belts, discs, and sleeves with this cleaning stick. The gum rubber composition of this stick cleans residue from abrasives to restore them to an almost new condition. Extends the useful life of abrasive belts, discs, and sleeves.

• Cleans sanding belts, discs, and sleeves extending their useful life • Works with all brands of abrasives • Easy to use, simply press gently against moving abrasive

Item # Description Color SANDCLEAN 8" 1-1/2" X 1-1/2" X 8" long Brown SANDCLEAN 12" 2" X 2" X 12" long White