NOTE: Mast tangs, such as Ronstan RF-43A, are HULL NUMBER: Lido 14 Class Sloop permitted at mast end of shroud and forestay rigging. In the case of RF-43A, BOAT WEIGHT (DRY): LBS. dimensions are to the tang's lower Approved Racing mounting hole. REQUIRED BALLAST: LBS. Measurements Shroud and forestay attachment points from diamond stay Center of jib halyard block RACING WEIGHT (MIN.) = 310 LBS. DO NOT SCALE attachment points sheave or casting opening Revised March, 2002, dlc Drawing original on Autosketch V 7.0 Revised April 19, 2002, jap Cleanup. Revised notes. Added hull# Racing weight includes hull, centerboard, Revised June 25, 2002, jap Corrected CB LE to Transom dimension rudder, tiller, mast, boom, lines, rigging and other items if permanently attached and 2 1/2" +/- 1/4" excludes sails, whisker pole, cushions, and CENTERBOARD DETAIL 7" +/- 1/4" any other items not permanently attached.

SAILS MEASURED AS FOLLOWS:

Before a sail is used for racing, it must be measured according to Article XIV of the Lido 14 Class Association By-Laws, be 67 1/8" +/- 1/4" 12 7/8" +/- 1/4" stamped, dated, and signed by Fleet Spreader Tube: Measurer, and must have a Lido 14 Royalty Length from mast wall Tag attached. (not including adjusting screw) 122" (10' 2") +/- 1/2" to top of extrusion Foil Foil Thickness: 7/8" +/- 1/8" from top to within 8" of bottom 6" +/- 1/4" 60" Maximum 44" 203" (16' 11") +/- 1/4" T op of 3/4" black band to top extrusion 8" 11 7/8" +/- 1/4" Whisker Pole: Extension from mast, Diamond Stay including all fittings Boom: Distance to mainsail outhaul Centerboard Jibe = 1/4" Maximum line from aft edge of mast 218" (18' 2") +/- 1/2" Center of hinge bolt to top extrusion for original cast mast 220" (18' 4") +/- 1/2" Center of hinge bolt to top extrusion for 6000 Series mast 72" Maximum

(Leading Edge minus Trailing Edge) 71 1/2" +/- 1/4"

117 1/4" (9' 9 1/4") Maximum 3/4" Black Band NOTES: Center of the forestay pin to 1. Maximum length is 60" excluding fittings and hangers. the leading edge of the mast 2. Maximum thickness is 1" except trailing edge at keel (A/C # 54). Mast Hinge at the height of the pivot bolt Bolt Hole 3. Essential dimensions are measured without removing the board. 49" +/- 1/4" 4. Chord dimensions are perpendicular to the leading edge at 8" and 44" locations from the tip. 5. Shape of bottom 8" is unrestricted. Centerboard hull slot width = 1 1/8" Minimum

24" +/- 1/4" BRIDLE-TRAVELER / TRANSOM DETAIL RUDDER DETAIL 95 1/2" +/- 1/2" Transom Boom NOTE: Bottom of Hull The upper rudder depth measurement NOTE: 48" +/- 1/2" point is at the intersection of the lines Single or 2:1 purchase representing the rudder's leading edge and Splice or Knot mainsheet is permitted. 18 3/4" the bottom of the hull. The lower point is at Foil the intersection of the line representing the Bridle 18 3/4" NOTE: leading edge and a line perpendicular to Jib fairlead track not required the leading edge tangent to the rudder tip.

27" Minimum Center of forestay pin to 22" Maximum forward inside edge of jib Outside of fairlead to outside of Foil Thickness: fairlead eye - both sides opposite fairlead 3/4" +/- 1/8" from top to within 5" of bottom 10" +/- 1/4" NOTES: 95" Minimum 64 3/4" Minimum 1. Rudder head fitting is required but design may vary. 2. Shape of bottom 5" is unrestricted so long as depth requirement (24") is met.