Installation Manual NAILBASE PANELS June 2021

The better way to buildTM

NAILBASE SIPs Installation Manual

Table of Contents Topics General Requirements ...... 3 Materials ...... 3

Details Air Barrier Details for Nailbase Panel Butt Joint ...... AB-1(NB) Nailbase Panel Retrofi t Over Existing Wall Sheathing ...... NB-1 Retrofi t Nailbase Panel Outside Corner ...... NB-2 Retrofi t Nailbase Panel Over Rim Joist ...... NB-3 Inside Corner Detail ...... NB-4 Retrofi t Nailbase Panel Edges ...... NB-5 Window Mounted at Exterior Plane (Header) ...... NB-6A Window Mounted at Exterior Plane (Sill) ...... NB-6B Window Left in Place (Header) ...... NB-7A Window Left in Place (Sill) ...... NB-7B Nailbase Wall Attachment: Concrete or Masonry Wall ...... NB-8 Exterior Wall Cladding: Brick & Stucco ...... NB-9 Exterior Wall Cladding: Vinyl & Wood Siding ...... NB-10 Electrical Wire Fastened to Nailbase Panel ...... NB-11 Pre-Fabricated Metal Chimney Installation in Wall ...... NB-12 Retrofi t Nailbase Panels on Roof Structure ...... NB-13 Retrofi t Roof & Wall Nailbase Connection at Overhang ...... NB-14 Nailbase Roof Overhang Details ...... NB-15 Nailbase Panel Attic Air Block ...... NB-16 Sloped Roof Applied to Nailbase SIPs ...... NB-17 Flat Roof Applied to Nailbase SIPs ...... NB-18 Nailbase Ceiling Panel ...... NB-19 LED Pot Light Installation in Ceiling SIPs ...... NB-20 Electrical Wire Fastened to Nailbase Roof SIP ...... NB-21 Pre-Fabricated Metal Chimney - Roof Installation ...... NB-22 Screw Fastener Detail for Securing Load to Nailbase Ceiling . NB-23

Steel Frame Nailbase Installation Typical Wall Detail ...... IN-1 Gable & Corner Trim Detail ...... IN-2 Peak & High Wall Detail ...... IN-3 Header & Trim @ Self Framing Walkdoor ...... IN-4 Header & Jamb Trim @ Overhead Door ...... IN-5

Nailbase SIP - Installation Manual 2 June 2021

NAILBASE SIPs Installation Manual

1. General Requirements 1.1 Scope The basic design and construction requirements for the Thermapan Nailbase retroﬁ t panel system is set forth in this speciﬁ cation.

Criteria for materials, environmental control, design loads, and structural design are included. Where requirements are based on internationally recognized standards and speciﬁ cations, these standards and speciﬁ cations are referenced without elaboration.

Installers shall reference engineering design package for fastening arrangements.

2. Materials 2.1 The Thermapan Nailbase SIP is composed of an expanded polystyrene (EPS) foam core laminated on one side with a layer of oriented strand board (OSB) with a structural adhesive.

2.2 Framing Lumber shall be DOC PS 20 or NLGA No.2 or better.

2.3 SIP screws shall conform to ICC-AC233.

2.4 Polyethylene (Poly) Sheathing shall conform to CAN/CGSB-37.2, CAN/CGSB-37.16, or ASTM D 4397.

2.5 Low expansion foam seal shall conform to AAMA 812-04.

2.6 Sill seal gasket is a ﬂ exible polyethylene foam gasketing strip that can help reduce air inﬁ ltration between a concrete or masonry surface and a lumber plate.

Nailbase SIP - Installation Manual 3 EXPANDABLE FOAM SEALANT

NAILBASE PANEL

CONTINUOUS POLY SHEATHING

EXISTING WALL OR ROOF (AND SHEATHING)

TITLE PROJECT AIR BARRIER DETAILS FOR NAILBASE PANEL BUTT JOINT

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 AB-1(NB) EXISTING WOOD FRAME WALL & INSULATION

NAILBASE PANEL

BARRIER

EXTERIOR CLADDING

CONTINOUS POLY SHEATHING

NOTE: SEE NB-10 & NB-11 FOR EXTERIOR CLADDING OPTIONS

TITLE PROJECT NAILBASE PANEL RETROFIT OVER EXISTING WALL SHEATHING

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-1 EXISTING WOOD FRAME WALL & INSULATION

NAILBASE PANEL

CONTINOUS POLY SHEATHING

APPLY SEALANT NAILBASE PANEL RECESS EPS AND AS PER OVERLAP WITH DRAWING AB-1 WOOD BLOCKING

FASTENERS PER ENGINEERED SHOP DRAWINGS

TITLE PROJECT RETROFIT NAILBASE PANEL OUTSIDE CORNER

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-2 EXISTING WOOD FRAME EXISTING WOOD FRAME WALL & INSULATION WALL & INSULATION CONTINOUS CONTINOUS POLY SHEATHING POLY SHEATHING

NAILBASE NAILBASE PANEL PANEL

FASTENERS PER ENGINEERED SHOP DRAWINGS

RIM RIM JOIST JOIST FLASHING

FOUNDATION FLASHING

RECOMMENDED ALTERNATE

TITLE PROJECT RETROFIT NAILBASE PANEL OVER RIM JOIST

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-3 EXISTING WOOD FRAME WALL & INSULATION

APPLY SEALANT AS PER DRAWING AB-1

NAILBASE PANEL

FASTENERS PER ENGINEERED SHOP DRAWINGS

CONTINOUS POLY SHEATHING

TITLE PROJECT

INSIDE CORNER DETAIL

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-4 NAILBASE PANELS OVER CONTINOUS POLY SHEATHING (TWO 4x16 PANELS & ONE CUT 1X16 PANEL SHOWN)

FASTENERS PER ENGINEERED SHOP DRAWINGS

TITLE PROJECT RETROFIT NAILBASE PANEL EDGES

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-5 NAILBASE PANEL FULLY ADHERED SHEATHING MEMBRANE WOOD FURRING STRIP EXTENDED INTO ROUGH OPENING (AIR BARRIER SYSTEM) WATER-RESISTIVE BARRIER EXISTING STRUCTURE

SLOPED METAL HEAD FLASHING TO FURRING STRIPS

EXTERIOR WINDOW TRIM FASTENED TO FURRING STRIPS

SHEATHING TAPE OVER HEAD FLASHING CONTINUOUS BEAD OF SEALANT SELF-ADHERED HEAD BETWEEN EXTENSION BOX AND FLASHING OVER FLANGE MEMBRANE (AIR BARRIER SYSTEM) METAL STRAP ANCHOR PLYWOOD/OSB EXTENSION BOX (CAULK INTERIOR CORNERS) LOW EXPANSION FOAM SEALANT AT INTERIOR PERIMETER BETWEEN WINDOW AND EXTENSION BOX (AIR BARRIER SYSTEM)

NOTE: SEE NB-6B FOR SILL DETAIL

TITLE PROJECT WINDOW MOUNTED AT EXTERIOR PLANE (HEADER)

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-6A LOW EXPANSION FOAM SEALANT AT INTERIOR PERIMETER BETWEEN BEVELED SIDING SLOPED SILL WINDOW AND PAN FLASHING (AIR BARRIER SYSTEM) CONTINUOUS SEALANT PLASTIC SHIM BETWEEN BACK DAM OF SILL PAN AND EXTENSION BOX SEALANT BETWEEN WINDOW AND (AIR BARRIER SYSTEM) SILL TRIM TO MINIMIZE WATER PENETRATION AT SILL JOINT CONTINUOUS BEAD OF SEALANT SILL TRIM BETWEEN EXTENSION BOX AND MEMBRANE (AIR BARRIER SYSTEM) PRE-MANUFACTURED PAN FLASHING WITH BACK DAM FULLY ADHERED SHEATHING MEMBRANE EXTENDED INTO PLYWOOD/OSB EXTENSION BOX ROUGH OPENING (CAULK INTERIOR CORNERS) (AIR BARRIER SYSTEM)

WOOD FURRING STRIP

EXISTING STRUCTURE NAILBASE PANEL

NOTE: SEE NB-6A FOR HEADER DETAIL

TITLE PROJECT WINDOW MOUNTED AT EXTERIOR PLANE (SILL)

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-6B NAILBASE PANEL

TREATED WOOD FURRING STRIP WATER-RESISTIVE BARRIER WATER-RESISTIVE BARRIER EXISTING STRUCTURE

SLOPED METAL HEAD FLASHING OVER TOP OF HEAD TRIM, FASTENED TO FURRING STRIPS SELF-ADHERED HEAD FLASHING; BUTTER TOP EDGE OF HEAD EXTERIOR WINDOW TRIM FLASHING WITH COMPATIBLE FASTENED TO FURRING STRIPS MASTIC TO REINFORCE SEAL WITH CLADDING VENT BETWEEN SHEATHING MEMBRANE FURRING STRIPS AT WINDOW HEAD LOW EXPANSION SEALANT AT INTERIOR PERIMETER BETWEEN HEAD OF TRIM EXTENSION BOX WINDOW AND ROUGH OPENING CUT 1” ON EACH SIDE FRAMING TO ALLOW DRAINAGE FULLY ADHERED SHEATHING MEMBRANE EXTENDED INTO DO NOT CAULK TRIM EXTENSION ROUGH OPENING BOX TO WINDOW HEAD

NOTE: SEE NB-7B FOR SILL DETAIL

TITLE PROJECT WINDOW LEFT IN PLACE (HEADER)

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-7A PRE-MANUFACTURED PAN FLASHING WITH BACK DAM

LOW EXPANSION FOAM SEALANT AT INTERIOR BETWEEN WINDOW AND PAN FLASHING

PLASTIC SHIM

SEALANT BETWEEN WINDOW AND SILL TRIM TO MINIMIZE WATER CONTINUOUS SEALANT PENETRATION AT SILL JOINT BEVELED SIDING SLOPED SILL SILL OF TRIM EXTENSION BOX

DO NOT APPLY FLASHING MEMBRANE OVER BOTTOM FULLY ADHERED SHEATHING FLANGE, ALLOW DRAINAGE; PLACE MEMBRANE EXTENDED INTO WASHER (UNDER EACH SCREW) OPENING OVER BEVELED SILL BETWEEN FLANGE AND FLASHING MEMBRANE FOR DRAINAGE SPACE

WATER-RESISTIVE BARRIER EXISTING STRUCTURE TREATED WOOD FURRING STRIP

NAILBASE PANEL

NOTE: SEE NB-7A FOR HEADER DETAIL

TITLE PROJECT WINDOW LEFT IN PLACE (SILL)

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-7B SIP SCREW FASTENED TO STRAPPING

WOOD STRAPPING NAILBASE WALL PANEL WOOD SILL SEAL STRAPPING GASKET 16'-0 (4876mm)

MASONRY SCREW OR NAIL FASTENING STRAPPING TO CONCRETE. 4'-0" (1220mm) FASTEN SIP SCREWS AS PER ENGINEERED EXTERIOR DRAWINGS WOOD STRAPPING MASONRY OR CONCRETE WALL APPLY FOAM SEAL BETWEEN ALL PANEL JOINTS 4'-0" (1220mm)

WOOD STRAPPING

GAP BETWEEN NAILBASE PANEL AND CONCRETE ELEVATION SECTION WALL SUITABLE FOR ELECTRICAL

TITLE PROJECT NAILBASE WALL ATTACHMENT (CONCRETE OR MASONRY WALL)

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-8 MASONRY VENEER

THERMAPAN CORROSION RESISTANT NAILBASE NON-ADHERING 2” RING NAILS OR #8 (MINIMUM) SCREWS WALL PANEL BREATHABLE WITH FULL THREAD PENETRATION INTO OSB WEATHER OSB RESISTIVE BARRIER SHEATHING OF SIP LAP BARRIER AT JOINTS MASONRY TIES INSTALLED @ 24” (600mm) O/C VERTICALLY & 16” (400 mm) O/C HORIZONTALLY (MAXIMUM) AS PER BUILDING CODE

BRICK VENEER BRICK SUPPORTED VENEER ON STEEL ANGLE OR BRICK LEDGE

1” AIR NON-ADHERING SPACE BREATHABLE WEATHER RESISTIVE BARRIER OSB EPS

STUCCO

THERMAPAN STUCCO NAILBASE WRAP WALL PANEL

OSB 2 LAYERS SHEATHING NON-ADHERING OF SIP BREATHABLE WEATHER RESISTIVE BARRIER

BROWN COAT

STUCCO FINISH COAT SCRATCH WIRE COAT NON-ADHERING LATH BREATHABLE WEATHER RESISTIVE BARRIER

TITLE PROJECT EXTERIOR WALL CLADDING BRICK & STUCCO

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-9 VINYL SIDING

THERMAPAN NAILBASE NON-ADHERING WALL PANEL BREATHABLE WEATHER RESISTIVE BARRIER FIBRE CEMENT OSB SIDING SHEATHING FOR FIBRE CEMENT LAP SIDING OF SIP LAP BARRIER AT REFER TO MANUFACTURER’S JOINTS RECOMMENDED FASTENING METHODS. VINYL SIDING

MINIMUM 1-1/2” NAILS OR STAPLES @ 16” MAX INTO OSB

WOOD SIDING NON-ADHERING THERMAPAN BREATHABLE WEATHER NAILBASE RESISTIVE BARRIER WALL PANEL

OSB WOOD SHEATHING FURRING FURRING REQUIREMENTS OF SIP FURRING FASTENER SPACING FASTENER SPACING SPACING (MIN 1-1/2” SCREWS) (MIN 1-1/4” NAILS)

WOOD 16” O/C 10” O/C 8” O/C SIDING 24” O/C 8” O/C 8” O/C

NOTE: ALL NAILS TO BE RING (ANNULARLY THREADED). FURRING TO BE AS RECOMMENDED BY SIDING MANUFACTURER.

LAP BARRIER AT JOINTS

TITLE PROJECT EXTERIOR WALL CLADDING: SIDING

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-10 MASONRY VENEER ELECTRICAL WIRE FASTENED TO OSB BENEATH MEMBRANE

MASONRY TIES INSTALLED @ 24” (600mm) O/C VERTICALLY & CORROSION RESISTANT 16” (400 mm) O/C HORIZONTALLY 2” RING NAILS OR #8 (MINIMUM) SCREWS (MAXIMUM) WITH FULL THREAD PENETRATION INTO OSB AS PER BUILDING CODE

BRICK VENEER

NON-ADHERING BREATHABLE WEATHER RESISTIVE BARRIER OSB EPS

WOOD SIDING

VERTICAL STRAPPING 16” O/C OR AS PER ELECTRICAL WIRE FASTENED TO SIDING SPECIFICATIONS OSB BENEATH MEMBRANE

GAP THROUGH STRAPPING

NON-ADHERING EPS BREATHABLE WEATHER RESISTIVE BARRIER OSB

TITLE PROJECT ELECTRICAL WIRE FASTENED TO NAILBASE SIP EXTERIOR

REFERENCE SCALE N.T.S. www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) MARCH 2021 NB-11 SHIELD COLLAR AS PER CHIMNEY MANUFACTURER

AIR GAP AS SPECIFIED BY CHIMNEY MANUFACTURER

CHIMNEY

FINISHING COLLAR

INTERIOR WALL FINISH

THERMAPAN NAILBASE PANEL

NOTE: ABOVE DETAILS ARE TYPICAL REQUIREMENTS TO INSTALL A PREFABRICATED METAL CHIMNEY IN A THERMAPAN STRUCTURAL INSULATED PANEL. THE CHIMNEY INSTALLATION MUST COMPLY WITH THE CHIMNEY MANUFACTURERS’S SPECIFICATION AND THE APPLICABLE BUILDING CODE.

TITLE PROJECT PRE-FABRICATED METAL CHIMNEY INSTALLATION IN WALL

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) OCTOBER 2019 NB-12 FASTENERS PER ENGINEERED SHOP DRAWINGS

4X16 NAILBASE PANELS OVER CONTINUOUS POLY SHEATHING

TRUSSES OR RAFTERS 24” O.C. (TYPCIAL)

TITLE PROJECT RETROFIT NAILBASE PANELS ON ROOF STRUCTURE

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-13 STEP 1 STEP 2 ANALYSE CONSTRUCTION DETAIL REMOVE OVERHANG PORTION AS SHOWN REMOVE ROOF PLY, TRUSS OVERHANG FACIA AND SOFFIT AS REQUIRED AT FACE OF WALL SHEATHING EXISTING PLY ROOF DECK

EXISTING CUT AND TRUSS SYSTEM REMOVE

INTERIOR FINISH EXISTING WALL EXISTING WALL SHEATHING

TYPICAL EAVE CONSTRUCTION DETAIL

STEP 3 STEP 4 INSTALL NAIL BASE WALL PANEL INSTALL NAIL BASE ROOF PANEL AND VAPOUR BARRIER ON ROOF BLIND FACIA AND SOFFIT TO INSTALL NAIL BASE PANEL ONTO WALL SHEATHING. CREATE OVERHANG SECURE PANEL TO TOP PLATE AS SHOWN AND INSTALL 2X3 FRAMING AT 24" OC TO SUPPORT SOFFIT AND BLIND FACIA SIP SCREWS CONTINUOUS POLY SHEATHING NAILBASE ROOF PANEL SECURE NAILBASE PANEL TO ONE OF EXISTING TOP PLATES WITH SIP SCREWS BLIND FACIA

NAILBASE PANEL SOFFIT FRAMING SIP AT 24" SCREWS OC MAX

30”MAX

TITLE PROJECT RETROFIT ROOF & WALL NAILBASE CONNECTION AT OVERHANG

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-14 TYPICAL EXISTING ROOF SHEATHING SOFFIT ASSEMBLY

EXISTING WALL SHEATHING EXISTING TRUSS EXISTING GABLE TRUSS

TYPICAL GABLE OVERHANG CONSTRUCTION DETAIL

TYPICAL EXISTING ROOF SHEATHING SOFFIT ASSEMBLY

EXISTING WALL SHEATHING EXISTING TRUSS EXTERIOR LIMIT OF EXISTING GABLE TRUSS NAILBASE WALL PANEL

OVERHANG ADJUSTMENT FOR NAIL BASE ATTACHMENT

NOTCH AND GROOVE NAILBASE PANEL TO FIT OVER NAILBASE EXISTING OVERHANG LADDER ROOF PANEL

SIP SCREWS CONTINOUS POLY SHEATHING TYPICAL EXISTING SOFFIT ASSEMBLY ROOF SHEATHING

SIP SCREWS EXISTING WALL SHEATHING EXISTING TRUSS EXISTING GABLE TRUSS

CUT AND REMOVE SOFFIT AS REQUIRED NAILBASE FOR NAIL BASE GAP WALL PANEL

NAIL BASE WALL AND ROOF INSTALLATION FOR TYPICAL GABLE OVERHANG INSTALLATION

TITLE PROJECT NAILBASE ROOF OVERHANG DETAILS

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-15 PLAN VIEW AT STEP 2 STEPS

1 CUT EXISTING ROOF SHEATHING AS REQUIRED

2 INSERT, FASTEN AND SEAL AIR BLOCK ROOF TRUSS SIZED FROM NAILBASE PANEL (ENSURE (ROOF RAFTER) BLOCKING FIT IS SUCH TO PREVENT AIR LEAKAGE WHEN SHEATHING IS RE-INSTALLED)

3 SEAL AND FASTEN ROOF SHEATHING CUT PIECE TO ROOF RAFTER WITH FASTENERS

4 APPLY NAILBASE PANEL (SEE NB-12)

CONTINUOUS CAULK BEADS SECURE SHEATHING ALONG FACE OF RAFTER 3 TO ROOF RAFTER AND AIR BLOCK PANEL WITH FASTENERS.

AIR BLOCK PANEL EPS CUT ROOF AIR BLOCK PANEL OSB SHEATHING SECTION VIEW

4 NAILBASE EXISTING PANEL ROOF SHEATHING

1 CUT ROOF SHEATHING 3 (SEE PLAN VIEW)

INSULATED AIRBLOCK 2 SIZED FROM NAILBASE PANEL FOAM SEAL AS REQUIRED*

CONTINUOUS CAULK ROOF TRUSS BEADS ALONG TOP AND BOTTOM OF AIR BLOCK PANEL*

EXISTING WALL (TYPICAL CONSTRUCTION) *NOTE: REFER TO AIR BARRIER (AB-3) DETAILS FOR SEALING NAILBASE PANEL CONNECTIONS.

TITLE PROJECT NAILBASE PANEL ATTIC AIR BLOCK

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) MARCH 2020 NB-16 THERMAPAN NAILBASE ROOF PANELS ASPHALT (TWO SHOWN) SHINGLES

NON-ADHERING BREATHABLE ROOFING UNDERLAYMENT INSTALLED AS PER MANUFACTURER’S DRIP EDGE INSTRUCTIONS

FASCIA COVER

2X_ FASCIA BOARD

DRIP EDGE STARTER SHINGLE INSTALLED AS PER MANUFACTURER’S FASCIA WEDGE INSTRUCTIONS FASCIA FOR PLUMB CUT BOARD 2X_ BLIND FASCIA FASCIA COVER

THERMAPAN METAL ROOFING OR NAILBASE CEDAR SHAKES ROOF PANELS (TWO SHOWN)

NON-ADHERING BREATHABLE ROOFING UNDERLAYMENT INSTALLED AS PER MANUFACTURER’S DRIP EDGE INSTRUCTIONS

FASCIA COVER FURRING INSTALLED AS PER MANUFACTURER’S 2X_ FASCIA BOARD INSTRUCTIONS

DRIP METAL ROOFING OR EDGE SHAKES INSTALLED AS PER MANUFACTURER’S FASCIA WEDGE INSTRUCTIONS FASCIA FOR PLUMB CUT BOARD 2X_ BLIND FASCIA FASCIA COVER

NOTE: VENTILATION OF ROOF NOT REQUIRED.

TITLE PROJECT SLOPED ROOFING APPLIED TO NAILBASE SIPS

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-17 NON-ADHERED MEMBRANE (EPDM, PVC, TPO, ETC.)

FASTENERS INTO OSB

PROTECTIVE SHEATHING OR MEMBRANE AS REQUIRED

OSB

EPS

ADHERED ROOFING MEMBRANE

TORCHED ON OR GLUED ON ROOFING MEMBRANE

OSB

EPS

NOTES: • NAILBASE SIP SURFACE TO BE DRY. • INSTALL MEMBRANE ACCORDING TO MEMBRANE MANUFACTURER’S DETAILS AND CONFORM TO REQUIREMENTS OF LOCAL BUILDING CODE.

TITLE PROJECT FLAT ROOFING APPLIED TO NAILBASE SIPS

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-18 TRUSS SYSTEM - FLAT CEILING (W, M, GABLE, ETC.) TRUSS SYSTEM

CAULK

CAP AND/OR PLATE

THERMAPAN SEE DRAWING 1" NAIL BASE PANEL W-3 FOR CAP AND/OR PLATES

SIP SCREW CONTINUOUS POLY SHEATHING EXPANDABLE INTERIOR FOAM SEALANT FINISH

TRUSS SYSTEM - SCISSORS CAULK

CUT PANEL ON ANGLE WITH PRAZI SAW TO SIP SCREW THERMAPAN BUTT UP ON NAIL BASE PANEL WALL

SEE DRAWING W-3 FOR CAP AND/OR PLATES

EXPANDABLE FOAM SEALANT CONTINUOUS POLY SHEATHING

INTERIOR FINISH

NOTES: SIP SCREWS TO BE INSTALLED EVERY 2’ O/C BOTH DIRECTIONS. REFER TO AIR BARRIER (AB-3) DETAILS FOR SEALING NAILBASE PANEL CONNECTIONS.

TITLE PROJECT

NAILBASE CEILING PANEL

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-19 DRIVER BOX

WIRING STRAPPING

LED RECESS CEILING FIXTURE* INTERIOR FINISH

* FIXTURE SPECIFICATIONS FIXTURE TO HAVE AMBIENT OPERATING TEMPERATURE +140F(+40C) MAXIMUM INSTALL AS PER MANUFACTURERS SPECIFICATIONS

PROJECT TITLE LED POT LIGHT INSTALLATION IN CEILING SIPS

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) NOVEMBER 2018 NB-20 METAL ROOFING OR CEDAR SHAKES

STRAPPING 16” O/C OR AS PER ROOFING SPECIFICATIONS

NON-ADHERING METAL ROOFING BREATHABLE ROOFING (OR SHAKES) INSTALLED UNDERLAYMENT AS PER MANUFACTURER’S INSTALLED AS PER INSTRUCTIONS MANUFACTURER’S INSTRUCTIONS

EPS

OSB ELECTRICAL WIRE FASTENED TO OSB BENEATH MEMBRANE

TITLE PROJECT ELECTRICAL WIRE FASTENED TO NAILBASE ROOF SIP

REFERENCE SCALE N.T.S. www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) MARCH 2021 NB-21 AIR GAP AS SPECIFIED BY CHIMNEY MANUFACTURER

WEATHER COLLAR AS PER CHIMNEY MANUFACTURER

CHIMNEY SUPPORT BOX AS PER CHIMNEY MANUFACTURER

THERMAPAN NAILBASE PANEL

INTERIOR WALL FINISH

TRIM COLLAR

2X__ BLOCKING AS PER PANEL THICKNESS AND OPENING SPECIFIED BY CHIMNEY MANUFACTURER

TITLE PROJECT PRE-FABRICATED METAL CHIMNEY - ROOF INSTALLATION

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) OCTOBER 2019 NB-22 TYPICAL SIP ROOF SECTION

ELECTRICAL BOX (OPTIONAL) THERMAPAN PANEL

SEE DETAIL A

FIXTURE FINISH CAP

FIXTURE FASTENING PLATE

THERMAPAN NAILBASE LOAD PANEL OSB SKiN

CEILING FINISH (DRYWALL OR WOOD PANELLING)

CEILING LOAD RESISTANCE CAN BE ACHIEVED WITH NUMBER 10 SHEET METAL SCREWS INSTALLED TO A SIP CEILING FINISH AS PANEL EPS LAYER DETAILED OR TO THE SIP SKIN DIRECTLY.

EACH SCREW CAN RESIST A PULL OUT OF PANEL OSB SKIN 90 POUNDS IN 7/16" OSB. CONTRACTOR TO CONFIRM LOAD TO BE SECURED AND NUMBER OF FASTENERS REQUIRED. MINIMUM 4 SCREWS CEILING FINISH PER FIXTURES. FULL THICKNESS OF OSB TO RECEIVE SCREW THREAD ON ANGLE AS DETAILED

DETAIL A

TITLE PROJECT SCREW FASTENER DETAIL FOR SECURING LOAD TO NAILBASE CEILING PANEL

REFERENCE SCALE

N.T.S.

www.thermapan.com DATE REVISION DWG. No. 1-877-443-WALL (9255) FEBRUARY 2020 NB-23 C DEÿF ÿ ""$ÿE )"ÿE ÿGF1

P'ÿ EEÿ#F ÿ "ÿEF ÿHÿ'%Qÿ"R#

C! SÿPÿ%Q GIÿ"C Eÿ Eÿ# ÿIE )"E"1 !ÿF ÿ C DEÿF ÿE )"ÿE ÿGF FÿFEE" ÿHÿ'%Qÿ#R#ÿDP ÿGIÿ"C 1

$ÿ UF ÿF $#ÿ Dÿ$" ÿ $ ÿ$DÿE ÿÿD"Tÿ SÿPÿ%Q GIÿ"C Eÿ Eÿ# ÿIE ÿ)"E"1 #FTÿ

C DE E$ÿ$ "ÿ $"F" GIÿ"C DÿHÿGÿÿ

" C DEÿ FÿEÿ IE#ÿÿ ÿ"ÿ #"DEDÿ E ÿ GF

$ # #

222 34567898@ A7 !" ÿ %&&''(ÿ)01 ÿÿ B ""$ÿD

B! FHÿ"B B CDÿE QÿRÿ%S ÿD Dÿ Dÿ# )"ÿD ÿFE1 ÿHD ÿ)"D"1

Fÿ Cÿ

$ÿ IE ÿE $#ÿ Cÿ$" ÿ $ ÿ$CÿD ÿÿC"Pÿ FHÿ"B

QÿRÿ%S Dÿ Dÿ# ÿHD ÿ)"D"1

B CDÿE #" ÿ Cÿ ÿD )"ÿD ÿFE1

B! FHÿ"B

#" Cÿÿ

" B CDÿ EÿDÿ FÿGÿ#" ÿ Cÿ ÿ"ÿ #"CDCÿ D ÿ FE

$ # #

222 34567898@ A7 !" ÿ %&&''(ÿ)01 ÿÿ B!CDÿE !##%ÿD )#ÿD!!ÿFE B" FIÿ#B! !ÿ$Dÿ P(ÿ!DD ÿ)FIÿ#B!1

%ÿ!TE!ÿE!%$ÿ!Cÿ%#!ÿ DGÿ!Cÿ %!ÿ%CÿD!ÿÿC#Gÿ FIÿ#B!

B!CDÿE ÿD QÿRÿ&SÿDÿ!Dÿ$! )!EÿEDD#!ÿUÿ(&Sÿ$V$ÿ ID ÿ)#D#1 CR ÿFIÿ#B!1

%ÿ!TE!ÿE!%$ÿ!Cÿ%#!ÿ !##%ÿ#ÿBBÿÿ %!ÿ%CÿD!ÿÿC#Gÿ FIÿ#B!

# B!CDÿ EÿDÿ DGÿHÿBBÿÿ ÿ#ÿ $#CDCÿ D!!ÿ FE

!%!$ $

222 34567898@ A 7 !"# ÿ &''((ÿ)01 ÿÿ B!DHÿI %B ÿH )#ÿH!!ÿEI ÿIHH#!ÿFÿ&Vÿ$W$ÿDU ÿEQÿ#B!1 ÿÿPÿB#! EQÿ#B! %ÿ!RI!ÿI!%$ÿ!Dÿ%#!ÿ TÿUÿ&V %!ÿ%DÿH!ÿÿD#Sÿ Hÿ!Hÿ$! EQÿ#B! QH )#H#1

B!DHÿI ÿH ÿÿPÿB#! )#ÿH!!ÿEI EQÿ#B! ÿIHH#!ÿFÿ&Vÿ$W$ÿDU ÿEQÿ#B!1

TÿUÿ&V %ÿ!RI!ÿI!%$ÿ!Dÿ%#!ÿ Hÿ!Hÿ$! %!ÿ%DÿH!ÿÿD#Sÿ QH )#H#1 EQÿ#B!

##!ÿDE

# B!DHÿ B!ÿCÿDEÿ!DÿFÿ IÿHÿ ÿ#ÿ #"!Bÿ##! $#DHDÿ H!!ÿ EI

!%!$ $

222 34567898@ A 7 !"# ÿ &''(ÿ)01 ÿÿ B CDÿE ÿD )"ÿD ÿFE EÿEDD" ÿSÿ'%Rÿ#T#ÿCQ ÿFIÿ"B 1

$ÿ GE ÿE $#ÿ Cÿ$" ÿ $ ÿ$CÿD ÿÿC"Hÿ FIÿ"B

$ÿ$ Cÿ H"" ÿ$ Cÿ

Bÿ C

B CDÿE ÿD )"ÿD ÿFE EÿEDD" ÿSÿ'%Rÿ#T#ÿCQ ÿFIÿ"B 1

$ÿ GE ÿE $#ÿ Cÿ$" ÿ $ ÿ$CÿD ÿÿC"Hÿ PÿQÿ%R FIÿ"B Dÿ Dÿ# ID )"D"1

$ÿ$ Cÿ H"" ÿ$ Cÿ CFÿ C

" B CDÿ B ÿUÿ CÿSÿ$ EÿDÿ ÿ"ÿ $ CÿH"" #"CDCÿ D ÿ FE

$ # #

222 34567898@ A7 !" ÿ %&&''(ÿ)01 ÿÿ