INSTALLATION SYSTEMS JM RhinoPlate™ System Fastener Selection Guide UltraFast AccuTrac System High Load AccuSeam System www.jm.com For a complete listing of FM approvals, please contact Johns Manville.
INSULATION ATTACHMENT SCREWS PRE-ASSEMBLED Product Name UltraFast® Fastener All Purpose Fastener UltraFast Pre-Assembled Fasteners
#3 Phillips Head *Hex head are with Drill Point special order only
¼" Hex Head UltraFast Phillips with UltraFast Phillips or Options with Spade Point #3 Phillips Head UltraFast Plastic Locking Plate Hex* head with UltraFast Metal Plate Phillips head – blue / #12 #12 blue fastener #12 blue fastener with 3" Galvalume® plate Color / Diameter Gray / #14 Hex head – black / #12 with 3" blue plate Hex head – black only 18–26 ga. metal, Deck Type 18–26 ga. metal & wood 18–26 ga. metal & wood wood & concrete
Available 15⁄8", 2¼", 3"–8" Phillips 15⁄8", 2¼", 3"–8" Phillips 1¼"–24" Lengths 15⁄8", 2¼", 27⁄8", 3¼", 3¾", 4½", 5"–8" Hex 15⁄8", 2¼", 27⁄8", 3¼", 3¾", 4½", 5"–8" Hex PLATES UltraFast Plastic Product Name UltraFast Metal Plates UltraFast Plus Plate Locking Plate
Options Recessed Flat bottom Flat bottom Low profile Color / Diameter Galvalume / 3" round Galvalume / 3" square Galvalume / 3" square Blue / 3" round Typically Phillips Head fasteners when directly Hex or Phillips head fasteners Hex or Phillips head fasteners Used With (standard plate) over hard board substrates (i.e., plywood, OSB)
Product Name UltraFast AccuTrac® Plate Heavy-Duty Low Profile Plate
Options Recessed Flat bottom Flat surface Color / Diameter Galvalume / 3" square Galvalume / 2¾" square
Used where a flat plate (no ribs) helps Typically AccuTrac automated AccuTrac automated performance or aesthetics Used With system and Hex head fasteners system and Phillips head fasteners (Equivalent approvals to the UltraFast Plate) MEMBRANE ATTACHMENT SCREWS PRE-ASSEMBLED Product Name All Purpose Fastener High Load Fastener Extra High Load Fastener High Load Pre-Assembled
Options #3 Phillips Head #3 Phillips Head Oversize #3 Phillips Head #3 Phillips Head Product Color / #15 blue screw Gray / #14 Blue / #15 Blue / #21 Diameter with 2 3⁄8" Galvalume Eyehook plate 18–26 ga. metal, wood & Deck Type 18–26 ga. metal, wood 20–26 ga. metal & wood 18–26 ga. metal, wood concrete
Available 11⁄4"–8", 10", 12" Blue 11⁄4"–24" 2"–8" 2"–8" Lengths 9", 11", 14"–20" Black PLATES Product Name Anchor Disc APB Plate High Load Plate Extra High Load Plate
Material Galvalume Galvalume Galvalume Galvalume
Dimensions 2" round 2" round with barbs 2 3⁄8" round with Eyehooks™ 3" round with Eyehooks
Examples of Popular Mechanically Attached Constructions Over Steel Deck (80 ksi)
Membrane Typically used 7' or 10' EPDM 7' or 10' EPDM 6' or 8' TPO 78" PVC 6' or 8' TPO 78" PVC 10' TPO 10' TPO with High Load Fastener Type Fastener for All Purpose High Load Extra High Load terminating Fastener single-ply 6" o.c. 6" o.c. 12" o.c. 18" o.c. 12" o.c. 12" o.c. Spacing membranes
Product Name PVC or TPO RhinoPlate® TreadSafe™ Polymer Batten Strip High Load AccuSeam™ Plate
PVC or TPO coated Galvalume Material Specially coated Galvalume plates & polymer tubes Proprietary Polymer Galvalume
Dimensions 3" round 3" round plate, 1½" long tube 1" wide x 250 ft. 2 3⁄8" round with Eyehooks
Examples of Popular Mechanically Attached Constructions Over Steel Deck (80 ksi) Membrane PVC or TPO PVC or TPO 10' EPDM These are standard High Load High Load or High Load or Plates specially stacked for use Fastener Type All Purpose Extra High Load Fastener RetroDriller Fastener with the AccuSeam automated system. They have equivalent Fastener Contact JM technical Contact JM technical 6" o.c. approvals to the High Load Plate. Spacing *The same approvals exist using a High Load Screw and High Load Plate. SPECIALTY DECK ATTACHMENT
Product Lightweight Concrete (LWC) UltraLok® Polymer Auger Polymer Auger Name Base Sheet Fastener Fastener Fastener Plates
Product Twin leg fastener Impact fastener with tube, Plate and screw are designed to lock together Features design with integral plate disk, and locking staple to minimize back-out and pop-up Product G-90 painted steel fastener G-90 steel fastener with Solid glass reinforced nylon Galvalume Material with Galvalume plate Galvalume plate 2.7" dia. plate assembled 2.7" dia. plate assembled 2" round (membrane) and Dimensions .675" dia. screw with 1" dia. head to fastener to fastener 3" round (insulation) Lightweight insulating Deck Type Gypsum & cementitious wood fiber Gypsum & cementitious wood fiber Gypsum & cementitious wood fiber concrete & gypsum Available 1.2", 1.7" 1.4", 1.8", 2.8", 3.8", 4.8" 2½"–12" NA Lengths 2-step process: Drive Installation Impact perpendicular to roof fastener perpendicular to ¼" square drive NA Requirements deck using a magnetic driver roof deck, then drive locking staple through tube/disk
Pre-Drill In gypsum, 7⁄16" dia. (may vary No No NA Required based on substrate hardness)
Structural Product UltraFast Lite-Deck Lite-Deck Purlin RetroDriller Zinc Nail-in Concrete Name Metal Plate Fastener Plate Fastener Fastener Anchor Fastener
One-piece expansion body Product #3 square drive and expander Features Nail-in anchor / Use flat bottom plate 3" square drive ¼" hex head ½" drill point drive pin
1 Dimensions NA 3" round NA 3" NA NA ⁄4" dia. Termination Structural Lightweight insulating concrete, Structural steel fastening into Deck Type Structural concrete steel purlins gypsum, cementitious wood fiber purlins (up to 3 ⁄16") concrete and (12–18 gauge) masonry walls Available 2", 2½", 3", 3¾", 4¾", NA 25⁄8", 3"–10", 12" NA 5", 6", 8", 10" 1¼" Lengths 3½", 4"–12" 5¾", 7", 8" Drill pilot hole Drill pilot hole Use high torque, Use high torque, Installation Drill pilot hole and and install with NA for gypsum and NA low RPM screw low RPM screw Requirements hammer in anchor a 3 lb. hammer lightweight decks gun (0–1800 RPM) gun (0–1800 RPM)
Pre-Drill 7 Yes Yes ⁄ 32" dia. NA Yes NA No No Required ¼" dia. INSULATION ADHESIVE INSTALLATION SYSTEMS JM Two-Part Urethane Insulation Adhesive JM RhinoPlate™ System UltraFast AccuTrac System High Load AccuSeam System
TYPICAL PULLOUT VALUES Structural Concrete Fastener UltraFast (#12) All Purpose (#14) High Load (#15) Extra High Load (#21) Fastener 18 ga. Steel 894 lbs. 918 lbs. 1323 lbs. NA NA (80 ksi) 20 ga. Steel 656 lbs. 693 lbs. 928 lbs. 1140 lbs. NA (80 ksi) 22 ga. Steel 488 lbs. 534 lbs. 690 lbs. 977 lbs. NA (80 ksi) 24 ga. Steel 425 lbs. 419 lbs. 586 lbs. 685 lbs. NA (80 ksi) 26 ga. Steel 294 lbs. 277 lbs. 403 lbs. 495 lbs. NA (80 ksi)
½" Plywood* 326 lbs. 410 lbs. 499 lbs. 725 lbs. NA
1" Wood Plank* 734 lbs. 820 lbs. 747 lbs. NA NA
Structural Rev. 0713 Concrete NA 844 lbs. NA NA 955 lbs. (3000 psi with 3⁄16" pilot hole) (3000 psi with 7⁄ 32" pilot hole) (1" embed. depth) PL2001 *Pullout values for wood decks are subject to variation due to wood species, wood grade and, for plywood, the number of plies. Always perform pull tests to determine deck suitability.
Please call 800-922-5922 for technical information.
Johns Manville – Roofing Systems Group 717 17th Street, Denver, CO 80202 www.jm.com
RhinoPlate™, UltraLok® and UltraFast® are registered trademarks of Johns Manville. AccuTrac®, RhinoBond®, Eyehook™, TreadSafe™ and AccuSeam™ are trademarks of OMG, Inc. Galvalume® is a registered trademark of BIEC International, Inc.