- Rev. 01152019 Rev. ® 1-800-327-2520 Low Angle Low Angle Block Plane P. O. Box 9 • Route 1 O. Box 9 • Route P. Warren, Maine 04864 Warren, Heirloom Quality Tools Heirloom Quality www.lie-nielsen.com [email protected] Made in Maine, USA, since 1981 : This product can expose you to lead, which This product can expose you to lead, which : WARNING is known to the State of California to cause cancer and birth to go information more For harm. reproductive other or defects hands after handling. Wash . www.P65Warnings.ca.gov © 2019 Lie-Nielsen Toolworks, Inc. © 2019 Lie-Nielsen Toolworks, stresses and ensures that the tool will remain flat and true. The cap The true. and flat remain will tool the that ensures and stresses is also Manganese Bronze; other parts are Brass and Stainless Steel. 60-62, cryogen Rockwell to hardened Steel Tool A2 is blade The ically treated and double tempered. Our heat treating technique Our heat treating and double tempered. treated ically ensures the blade will take and hold a very fine edge for a long on the surface-ground is fully blade the treating, heat After time. top, back, and cutting edge, provides giving thickness ⅛" a The smooth, flat quickly. surface very finish that mirror a take will cutting. solid chatter-free Oc- flat. dead lapped is casting body Bronze The Maintenance: casional hand lapping with fine wet/dry sandpaper (320 grit or true. it keep and dings remove help will surface flat a on higher) The cap can be polished with any good brass polish, although many people like the patina that Bronze gets with age and use. the threaded rod, adjuster nut, and spinwheel light oiling on A lightly kept be should blade The freely. moving them keep will We when the tool is not in use. oiled to prevent rust, especially recommend Jojoba Oil, a plant based oil product that is non-toxic, abrasive fine a use we shop, our in Also, use. to easy and odor-free handblock to remove any light surface oxide from tool bodies and blades. Jojoba Oil and abrasive handblocks are available from us. for the and workmanship are guaranteed Guarantee: Materials are We parts. replacement for repairs or of your tool. Call life for advice if you ever have a problem using your tool. available - - ). A tool with with tool A ). " : The blade is flat ground at 25° and sits bevel up in : We use Manganese Bronze for the bodies. These These use Manganese Bronze for the bodies. We :

Low Angle Block Plane adjust the should be able to You Do not overtighten.

Materials wheel. blade after loosening the spinwheel about ¼ turn. castings are fully stress-relieved, a process that removes inherent

holding the blade and cap, adjust the blade. Tighten the spin Tighten holding the blade and cap, adjust the blade. of the screw. Loosen the spinwheel and, with your thumb still and, with your thumb spinwheel Loosen the screw. of the supporting the sole and your thumb on the cap iron just in front : Hold the tool in one hand with your fingers your with hand one in tool the Hold Blade Adjustment: website in both DVD and streaming formats. , available via our video, Plane Sharpening, available via our Charlesworth’s For information on sharpening, we recommend David For information on sharpening, we recommend David razor edge quickly, and improve edge life in hardwoods. and improve edge razor edge quickly, secondary bevel of 5° will increase performance, help achieve a achieve help performance, increase will 5° of bevel secondary : The blade comes ready to use, but honing a The blade comes ready to use, but honing Blade Sharpening: on the leading edge of the mouth to allow a bigger shaving to pass. to shaving bigger a allow to mouth the of edge leading the on a heavier cut, the tool can be easily modified by filing a chamfer filing by modified easily be can tool the cut, heavier a a large mouth will not perform as well on finish cuts. If you need you If cuts. finish on well as perform not will mouth large a This tool is set up to take thin shavings (.008 - .010 - (.008 shavings thin take to up set is tool This Geometry makes it an excellent choice for end grain. for precise control with minimal backlash. the body at 12°, making the cutting angle 37°. The low angle our other block planes, the blade is adjusted with a captive nut with a captive is adjusted blade the block planes, our other Our No. 102 Low Angle Block Plane is fashioned in such a pleas Our No. 102 Low woodworking. Like for most is suitable which .010" cut, .008 - Low Angle Block Plane Angle Block Low is made to take a maximumThe mouth of the plane in your shop. ing shape that it will rapidly become one of the most used tools ing shape that it will rapidly become one