DOCSLIB.ORG

Numerical Study on the Interfacial Behavior of Mg/Al Plate in Explosive/Impact Welding

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Numerical Study on the Interfacial Behavior of Mg/Al Plate in Explosive/Impact Welding Sci Eng Compos Mater 2017; 24(4): 581–590 Xiaodan Yuan, Wenxian Wang*, Xiaoqing Cao, Tingting Zhang, Ruishan Xie and Ruifeng Liu Numerical study on the interfacial behavior of Mg/Al plate in explosive/impact welding DOI 10.1515/secm-2015-0316 Received March 13, 2015; accepted October 11, 2015; previously 1 Introduction published online December 18, 2015 Magnesium alloys, one of the lightest structural metals Abstract: In this study, the process of explosive welding with a density one-third lighter than that of aluminum of Mg/Al plate is represented, and the interfacial behavior alloys, have been researched extensively for industrial of two metals is researched. The objective of this work is applications during the past decades [1]. However, the to investigate the factors that affect the quality of explo- poor corrosion resistance of magnesium limits its appli- sive bonding and the distribution of physical parameters cation in industry. Aluminum alloys, which offer high on the collision. A finite difference engineering package strength-to-weight ratio, good formability, and good cor- with smoothed particle hydrodynamics method is used rosion resistance, are widely used in the aerospace and to model the oblique impact of a thin flyer plate (Al) on automobile industries [2]. Composite laminates of magne- a relatively thick base plate (Mg). Wavy interface and jet- sium alloys and aluminum alloys, which take advantage ting phenomenon, which existed in the experiment, are of their high specific strength and overcome disadvan- well reproduced in the simulation. The contours of pres- tages of magnesium alloys, would be promising structural sure, shear stress, velocity, and effective plastic strain of materials. Therefore, the technology for joining aluminum magnesium and aluminum are also distinctly described. alloys to magnesium alloys is required for manufacturing The bonding turns out to be a possible solid-state welding new structural materials. Recently, macroscopic compos- process. The effective plastic strain exceeds a minimum ites and/or multilayer laminates of aluminum and mag- value, and the shear stress is just the opposite sign in this nesium alloys have received much attention [3–9]. This simulation where available bonding occurred. Wave for- composite laminate may own a good combination of the mation appears to be the result of variation in the veloc- properties of aluminum and magnesium alloys. ity distribution on the interface and periodic disturbances By traditional techniques, brittle intermetallics are of magnesium and aluminum. A transition from straight easy to generate on the bonding interface of magnesium to wave occurs along the interface. High values of plastic alloys and aluminum alloys, which greatly reduce plastic- strain of two metals are predicted on the interface. ity [10–12]. The aim of this study is to produce a composite plate via cladding aluminum alloys plate to magnesium Keywords: impact/explosive welding; jetting; Mg/Al; sim- alloys plate by explosive welding. High energy rate ulation; wave. welding methods are capable of producing good-quality and large-area bonding bi-metal plates, including plates with grossly different mechanical properties [13]. As a main method, explosive welding has been developed and widely applied in industry production for decades. *Corresponding author: Wenxian Wang, College of Materials As one of the joining technologies, explosive welding has Science and Engineering, Taiyuan University of Technology, 79 West a number of benefits in comparison with other conven- Yingze Street, Taiyuan 030024, Shanxi Province, China, tional welding techniques. The primary advantage is its e-mail: [email protected]; and Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of capability to fabricate layered target with a high-quality Education, 79 West Yingze Street, 030024 Taiyuan, Shanxi Province, metallurgical bonding between similar or dissimilar China metal plates [14–19], such as steel-steel plates [14, 15], Xiaodan Yuan, Xiaoqing Cao, Tingting Zhang, Ruishan Xie and titanium-stainless steel clad plates [16], titanium-alu- Ruifeng Liu: College of Materials Science and Engineering, Taiyuan minum clad plates [17], copper-stainless steel clad plates University of Technology, 79 West Yingze Street, 030024 Taiyuan, Shanxi Province, China; and Key Laboratory of Interface Science and [18], or other multi-layer materials. Another advantage is Engineering in Advanced Materials, Ministry of Education, 79 West higher bonding strength than the flyer plate or the base Yingze Street, 030024 Taiyuan, Shanxi Province, China plate. In addition, it allows the fabrication of large-scale 582 X.D. Yuan et al.: Study on the interfacial behavior of Mg/Al plate composite plates. In the process of welding, some com- process [24] have been investigated. With regard to the plicated physical phenomena, such as explosion, high- numerical simulation, FEM has been applied to simu- speed collision, plastic deformation of metal plates, late the explosive welding in recent works. EI-Sobky and interaction of different materials, moving interface or free Blazynski studied the explosive welding process using a surface, and high-temperature and high-pressure states, liquid analogue, which is based on the similarity between occur in very short duration due to detonation effect of hydrodynamic fluid behavior and material deformation the explosive [20]. Furthermore, the process is capable of in explosive welding. Lazari and Al-Hassani analyzed the joining with high surface areas due to its ability to dis- transient response of metal plates under explosive loading. tribute the high energy density through explosion [21]. A Oberg et al. simulated the process employing Lagrangian schematic illustration of explosive welding is shown in finite difference code method but only obtained jetting. In Figure 1. The flyer plate impacts on the base plate after Akihisa’s [24] paper, wavy interface was formed, but there explosion. The metal plates are made to collide obliquely was not any jetting reproduced. Akbari Mousavi et al. with each other at high velocity after the detonation of studied the process using Euler processor. The materials at the explosive charge with rate Vd. The flyer plate col- the collision point were considered to behave like a liquid. lides to the base plate with rate Vp under the impetus of The straight or wavy interface and jetting phenomena the detonation wave. During the high-speed impact of were modeled, and the velocity of jet was also predicted. metal plates, a high-speed jet is produced between the Euler computation can be applicable to plate impact, but metal plates. The appropriate impact angle β and impact historical process is difficult to be understood [25]. Akbari velocity Vp are required for well-bonding. Collision point Mousavi and Burley [26] also simulated the explosive S moves forward with rate Vcp governing the time avail- welding of titanium and steel plates using the model of able for bonding. The high pressure during the collision low detonation velocity explosives and analyzed two cri- process also leads to considerable local plastic deforma- teria that form the basis of a welding window including tion of the metals in the bonding zone. The process of the shear stress and plastic strain. However, their simulations explosive welding is finished in an instant, as the release did not model the whole adhesion process of two sur- of explosive energy and the interaction of metal system faces. Akbari Mousavi and Al-Hassani [27] used ABAQUS are completed in microseconds. with Arbitrary Eulerian Lagrangian formulation to model Therefore, explosively driven impact welding is a true the process of explosively driven plate. But only the last example of multidisciplinary research, as the phenomena contacting layers were shown in the ABAQUS figures. In associated with it fall under the various branches of engi- addition, the wave interface is not obvious. Tanaka [28] neering science. As a multidisciplinary research field, the simulated the explosion and gained well wave structure mechanism of explosive welding has been explored by and jetting using smoothed particle hydrodynamics (SPH) many investigators in the past several years. Some vari- method. SPH is a gridless Lagrangian hydrodynamics eties of research work about the welding interface [14], using particles. Unlike conventional Lagrangian tech- bond strength [22], welding window theory [19], joint niques, SPH avoids mesh tangling and is therefore much mechanism [23], and numerical simulation of welding more robust in its treatment of problems with large mate- rial distortions [29]. Therefore, in this work, SPH method is applied to study the interfacial behavior of the explo- sion welding of Mg/Al plates. Vd High explosive Zhang and Wang [30] and Yan et al. [2] have success- Air flow fully obtained Mg/Al alloy plates with good bonding by explosive welding. However, only the microstructure and Flyer plate mechanical characteristics of Mg/Al alloys composite plate were investigated by experiments. Few studied the Base plate explosive welding process of Mg/Al alloys plate by simu- lation and researched its interfacial deformation behavior. Therefore, in this paper, the main aims are to numerically Vp β simulate the impact process of Mg/Al alloys plates; to S research the distribution of physical parameters such as Vcp contact pressure, velocity effective plastic strain, and shear Figure 1: Schematic drawing
Load more

Recommended publications
  • Pretoria, 18 April 2007 2 No
    Pretoria, 18 April 2007 2 No. 29790 GOVERNMENT GAZETTE. 18 APRIL 2007 CONTENTS Page Gazette No. No. No. GENERAL NOnCE Safety and Security, Department of General Notice 433 Explosives Act (15/2003): Draft Explosives Regulations, 2007 .. 3 29790 STAATSKOERANT, 18 APRIL 2007 NO.29790 3 GENERAL NOTICE NOTICE 433 OF 2007 DRAFT EXPLOSIVE REGULATIONS 2007 The Minister for Safety and Security intends to put the Explosives Act, 2003, (Act No. 15 of 2003) in operation once the Explosive Regulations has been finalised. Draft Regulations are hereby published for general information and comment from interested parties. IMPORTANT NOTE: This is merely a working document which is used to obtain the input of interest groups. The finalisation of the draft Regulations, will ultimately be done after the consultation process has been concluded. NO PART OF THE CONTENT OF THIS DOCUMENT OR ANY ALTERATION THEREOF MAY BE CONSIDERED AS A COMMITMENT TO THE FINAL PROVISIONS OF THE REGULATIONS Kindly note that as this is a working document certain technical correction with regard to the numbering, spacing and general layout still need to be done. Any comments, contributions or proposals on the Regulations may be submitted within 6 weeks from the date of publication of this Notice in writing to the following; e-mail address:[email protected] fax number: (012) 393 7126 Postal address: Dir. K Strydom Legal Service SAPS Private Bag X302 PRETORIA 0001 4 No. 29790 GOVERNMENT GAZETTE, 18 APRIL 2007 DRAFT EXPLOSIVES REGULATIONS Issued in terms of section 33(1) of the Explosives Act, 2003 (Act No 15 of 2003) 2007-02-28 STAATSKOERANT, 18 APRIL 2007 No.29790 5 DEPARTMENT OF SAFETY AND SECURITY Explosives Act, 2003 (Act No.
    [Show full text]
  • Explosive Forming – Economical Technology for Aerospace Structures
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by Directory of Open Access Journals EXPLOSIVE FORMING – ECONOMICAL TECHNOLOGY FOR AEROSPACE STRUCTURES Anniversary Session “Celebrating 100 year of the first jet aircraft invented by Henri Coanda”, organized by INCAS, COMOTI and Henri Coanda Association, 14 December 2010, Bucharest, Romania Victor GHIZDAVU*, Niculae MARIN** *Corresponding author Military Technical Academy of Bucharest, Bdul George Coşbuc 81-83, Sector 5, 050141, Romania [email protected] **Aerospace Consulting Bdul Iuliu Maniu 220, Bucharest 061126, Romania [email protected] DOI: 10.13111/2066-8201.2010.2.4.15 Abstract: The explosive forming represents a technological alternative for obtaining small-lot parts, with inexpensive and efficient manufacturing preparation. The explosive forming processing methods present a series of important advantages, being recommended for the wide-scale application in the aerospace industry. The economic benefit varies from case to case, independent from the part type, manufacturing series and user. Key Words: explosive forming, economical technology, wide-scale application, aerospace structures. 1. INTRODUCTION The explosive forming processing methods present a series of important advantages, being recommended for the wide-scale application in the aerospace industry. By using the high explosive forming, items can be obtained, with different shapes and almost unlimited overall size, made of heavy-duty materials. Economically, there is the possibility of costs decreasing of the forming operation, below 1/10th of those necessary for classic forming technologies, especially in what concerns the prototype and small-scale production. The economic benefit varies from case to case, independent from the part type, manufacturing series and user.
    [Show full text]
  • MSL Engineering Limited Platinum Blue House 1St Floor, 18 the Avenue Egham, Surrey, TW20 9AB
    SMR Final Report 121404 Purpose of Issue Rev Date of Issue Author Agreed Approved Issued for information 0 Aug 2004 SM Issued for internal comment 1 November 2004 AFD DJM JB Issued as Final Report 2 December 2004 AFD DJM JB This Final report has been reviewed and approved by the Mineral Management Service. Approval does not signify that the contents necessarily reflect the views and policies of the Service, nor does mention of trade names or commercial products constitute endorsement or recommendation for use. This study was funded by the Mineral Management Service, U.S. Department of the Interior, Washington, D.C., under Contract Number 1435-01-04-CT-35320 ASSESSMENT OF REPAIR TECHNIQUES FOR AGEING OR DAMAGED STRUCTURES Project #502 DOC REF C357R001 Rev 1 NOV 2004 MSL Engineering Limited Platinum Blue House 1st Floor, 18 The Avenue Egham, Surrey, TW20 9AB Tel: +44 (0)1784 439194 Fax: +44 (0)1784 439198 E-mail: [email protected] C357R001Rev 2, December 2004 MMS Project #502 NUMBER DETAILS OF REVISION 0 Issued for information, August 2004 1 Issued for comment, November 2004. Extensive revisions throughout, including restructuring of report. 2 Issued as Final Report, December 2004. Conversion table added, Figure showing clamp details to avoid added, and general editorial revisions. C357R001Rev 2, December 2004 MMS Project #502 Assessment of Repair Techniques for Ageing or Damaged Structures By Dr. Adrian F Dier MSL Services Corporation Final Project Report: ASSESSMENT OF REPAIR TECHNIQUES FOR AGEING OR DAMAGED STRUCTURES MMS Project Number 502 November 2004 C357R001Rev 2, December 2004 i This Final report has been reviewed a nd approved by the Mineral Management Service.
    [Show full text]
  • Strength Simulations of Tension Bars for Heavy Lifting
    Strength simulations of tension bars for heavy lifting Hållfasthetssimuleringar av dragstag för tunga lyft Arvid Hoikka Faculty of health, science and technology Degree project for master of science in engineering, mechanical engineering 30 credit points Supervisor: Jens Bergström Examiner: Pavel Krakhmalev Date: 2018-08-13 Abstract Proplate, a world leading company, is expert on volume-based cutting and machining of both ordinary steel as well as stainless steel. One of Proplate’s mayor products is tension bars, which is a component made to balance high forces and give stability to structures such as cranes, buildings, bridges and much more. Proplate builds their tension bars in different high strength steel materials, purchased from SSAB, and sells them worldwide. Proplate would like to market themselves better and wishes to produce a catalogue for the maximum load that can be applied to their tension bars, as competitors Pretec and Macalloy, already have for their tension bars. The purpose of the project has been to investigate the tension bars and the maximum load they can withstand before failure. The tension bars have been modeled in the CAD-program Creo Parametric, and then sent to the finite element method program ABAQUS to analyze their structural strength. Three different types of tension bars, and a fourth tension bar (called the walnut-strap) used as a connecting element between some of the tension bars, were investigated. They were modeled with sprints, to hold several tension bars together, and with a construction called loader, to simplify the model load application step. The three different types of tension bars have been analyzed as individual and also when connected to other tension bars.
    [Show full text]
  • Ce Zhang · Jianming Yang a History of Mechanical Engineering a History of Mechanical Engineering Ce Zhang • Jianming Yang
    Ce Zhang · Jianming Yang A History of Mechanical Engineering A History of Mechanical Engineering Ce Zhang • Jianming Yang A History of Mechanical Engineering 123 Ce Zhang Jianming Yang Tianjin University Memorial University of Newfoundland Tianjin, China St. John’s, NL, Canada ISBN 978-981-15-0832-5 ISBN 978-981-15-0833-2 (eBook) https://doi.org/10.1007/978-981-15-0833-2 © Springer Nature Singapore Pte Ltd. 2020 This work is subject to copyright. All rights are reserved by the Publisher, whether the whole or part of the material is concerned, specifically the rights of translation, reprinting, reuse of illustrations, recitation, broadcasting, reproduction on microfilms or in any other physical way, and transmission or information storage and retrieval, electronic adaptation, computer software, or by similar or dissimilar methodology now known or hereafter developed. The use of general descriptive names, registered names, trademarks, service marks, etc. in this publication does not imply, even in the absence of a specific statement, that such names are exempt from the relevant protective laws and regulations and therefore free for general use. The publisher, the authors and the editors are safe to assume that the advice and information in this book are believed to be true and accurate at the date of publication. Neither the publisher nor the authors or the editors give a warranty, expressed or implied, with respect to the material contained herein or for any errors or omissions that may have been made. The publisher remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. This Springer imprint is published by the registered company Springer Nature Singapore Pte Ltd.
    [Show full text]
  • TECHNICKÝ SLOVNÍK Anglický Jazyk
    Název projektu Rozvoj technického vzdělávání v Jihočeském kraji Číslo projektu CZ.1.07/1.1.00/44.0007 Partner projektu Střední škola, České Velenice, Revoluční 220 TECHNICKÝ SLOVNÍK pro strojírenské obory Anglický jazyk Aleš Brothánek Obsah: 1. Brazing, welding, soldering 3 2. Metal forming 10 3. Heat and chemical treatment 22 4. Machining 30 5. Surface finishing 45 6. Activity in mechanical engineering 57 7. Assembly 65 8. Materials 72 Poznámka: autor anglického technického slovníku níže uvedené texty vybral, didakticky upravil (parafrázoval) v souladu s dikcí autorského zákona a dále již jen dle potřeby pokrátil tak, aby korespondovaly s podobou technického slovníku pro Německý jazyk. Citace dle: ČSN ISO 690:2011-Bibliografické citace. 2 Brazing, welding, soldering Brazing - The American Welding Society (AWS), defines brazing as a group of joining processes that produce coalescence of materials by heating them to the brazing temperature and by using a filler metal (solder) having a liquidus above 840°F (450°C), and below the solidus of the base metals.1 Soldering - Soldering has the same definition as brazing except for the fact that the filler metal used has a liquidus below 840°F (450°C) and below the solidus of the base metals.2 Welding joins metals by melting and fusing them together, usually with the addition of a welding filler metal. The joints produced are strong, usually as strong as the metals joined or even stronger. In order to fuse the metals, a concentrated heat is applied directly to the joint area. This heat is high
    [Show full text]
  • ME8351 – Manufacturing Technology-I
    JEPPIAAR ENGINEERING COLLEGE Jeppiaar Nagar, Rajiv Gandhi Salai – 600 119 DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK III SEMESTER ME8351 – Manufacturing Technology-I Regulation – 2017 JEPPIAAR ENGINEERING COLLEGE Jeppiaar Nagar, Rajiv Gandhi Salai – 600 119 DEPARTMENT OF MECHANICAL ENGINEERING QUESTION BANK SUBJECT : ME8351 MANUFACTURING TECHNOLOGY-I YEAR /SEM: II /III UNIT- I METAL CASTING PROCESSES Sand Casting : Sand Mould – Type of patterns - Pattern Materials – Pattern allowances –Moulding sand Properties and testing – Cores –Types and applications – Moulding machines– Types and applications; Melting furnaces : Blast and Cupola Furnaces; Principle of special casting processes : Shell - investment – Ceramic mould – Pressure die casting - Centrifugal Casting - CO2 process – Stir casting; Defects in Sand casting PART – A CO Mapping : C204.1 Q.No Questions BT Competence PO Level 1 State any four types of patterns. BTL-2 Understanding PO3,PO12 2 What are chaplets? BTL-1 Remembering PO1 3 Define casting. BTL-1 Remembering PO1,PO5,PO 7 4 Mention any two advantages and disadvantages of die BTL-2 Understanding PO1,PO7 casting. 5 Write the requirements of good pattern. BTL-2 Understanding PO1, PO7 6 What is core venting? BTL-1 Remembering PO3 7 What function of core? BTL-1 Remembering PO1 8 Which process is called lost waxing method? Why? BTL-2 Understanding PO1,PO7 9 What is the function of core print? BTL-2 Understanding PO1 10 What are the advantages and applications of ceramic BTL-2 Understanding PO1,PO7 moulds? 11 What are the pattern materials? BTL-1 Remembering PO1,PO3 12 Explain the term fettling. BTL-1 Remembering PO1,PO12 13 Name the steps involved in making a casting.
    [Show full text]
  • Lecture Notes on Metal Forming Process
    LECTURE NOTES ON METAL FORMING PROCESS 2019 - 2020 III B.E VI Semester Mr. Sachin Pande, Assistant Professor SECAB INSTITUTE OF ENGINEERING AND TECHNOLOG Navraspur Bagalkot road,Vijaypur – 586101 Department of Mechanical Engineering Page 1 METAL FORMING B.E, VI Semester, Mechanical Engineering [As per Choice Based Credit System (CBCS) scheme] UNIT 1 Stress, strain, Two dimensional stress analysis and three dimensional stress analysis, relation between engineering stress and true stress, relation between engineering strain and true strain, yield criteria, yield locus, theory of plasticity, Hot working, cold working, strain hardening, recovery, recrystallisation and grain growth, Comparison of properties of Cold and Hot worked parts UNIT II ROLLING: Bulk deformation processes - Economics of bulk forming, principles and theory of rolling, types of Rolling mills and products. Forces in rolling and power requirements, applications and, limitations, defects in rolled products - machinery and Equipment. FORGING PROCESSES: Principles of forging -Types Forging - Smith forging, Drop Forging - Roll forging - Forging hammers: Rotary forging - forging defects, Forces in forging of strip, disc and power requirements, applications, Equipment and their selection. UNIT III EXTRUSION PROCESSES: Basic extrusion process and its characteristics. Mechanics of hot and cold extrusion - Forward extrusion and backward extrusion - Impact extrusion Hydrostatic extrusion, forces in extrusion of cylindrical and non cylindrical components - characteristics and defects in extruded parts. Wire Drawing: Process Mechanics and its characteristics, determination of degree of drawing, drawing force, power, and number of stages-defects in products. UNIT IV Sheet Metal Working - Economical Considerations - Stamping, forming and other cold working processes: Blanking and piercing - Bending and forming - Drawing and its types - Cup drawing and Tube drawing - coining - Hot and cold spinning.
    [Show full text]
  • Development of Explosive-Welding Techniques for Fabrication of Regeneratively Cooled Thrust Chambers for Large-Rocket- Engine Requirements
    DEVELOPMENT OF EXPLOSIVE-WELDING TECHNIQUES FOR FABRICATION OF REGENERATIVELY COOLED THRUST CHAMBERS FOR LARGE-ROCKET- ENGINE REQUIREMENTS E. G. Smith, Jr., D. Laber, V. D. Linse, and M. J. Ryan prepared for NATIONAL AERONAUTICS AND SPACE ADMINISTRATION Contract NAS3-10306 June 15, 1971 BATTELLE COLUMBUS LABORATORIES FINAL REPORT DEVELOPMENT OF EXPLOSIVE-WELDING FOR FABRICATION OF REGENERATIVELY -COOLED THRUST CHAMBERS FOR LARGE-ROCKET - ENGINE REQUIREMENTS E. G. Smith, Jr,, D. Laber, V. D. Linse, and M. J. Ryan prepared for NATIONAL AERONAUTICS AND SPACE ADMINISTRATION LEWIS RESEARCH CENTER Contract NAS3 - 10306 June 15, 1971 NASA-Lewis Research Center Cleveland, Ohio John M. Kazaroff Chemical Rockets Division FOREWORD The research described herein was conducted by Battelle's Columbus Laboratories, Materials Design and Fabrication Division, from June 28, 1967, to September 15. 1970, and performed under NASA Contract NAS3- 10306. The work was conducted under the management of NASA Project Manager, John M. Kazaroff, Chemical Rockets I3iv1sioa, NASA-Lewis Research Center. The authors acknowledge contributions of several individuals to the research work described in the report. The plasma-spray experiments and oxide-coating preparatloln was performed by Mr. R. L. Heestand. The fusion-welding studies in the pz-eparati,on of the Allvac 718 shell structure for the cylindrical spoolpiece were couductetl by Mr. D. L. Cheever. During the latter portion of the program, Mr. R. L. Martin con- tributed substantially to the explosive welding studies, particularly the preparatron and completion of the stainless steellHastelloy X spoolpiece. The data generated during the program are recorded in Book Nos. 25103, 25170, 25537, 25951, 26640, and 27454.
    [Show full text]
  • Sheet Metalworking Terminology Sheet-Metal Characteristics • Elongation – the Capability of the Sheet Metal to Stretch Without Necking and Failure
    ME477 Fall 2004 Introduction SHEET • Cutting and forming thin sheets of metal usually performed as cold working METALWORKING • Sheet metal = 0.4 (1/64) to 6 mm (1/4in) thick 1. Cutting Operation • Plate stock > 6 mm thick 2. Bending Operation • Advantage - High strength, good dimensional 3. Drawing accuracy, good surface finish, economical mass 4. Other Sheet-metal Forming production (low cost). 5. Dies and Presses • Cutting, bending, drawing γ 6. Sheet-metal Operation ε1 Localized necking 7. Bending of Tube Stock θ=55° Because ν=0.5 in plasticity, ε =-2ε =-2ε ε3,ε2 ε1 ε ε2 1 2 3 2θ 1 2 Sheet Metalworking Terminology Sheet-metal Characteristics • Elongation – the capability of the sheet metal to stretch without necking and failure. • “Punch-and-die” • Yield-point elongation – Lüeder’s bands on Low-carbon steels and Al-Mg alloys. – Tooling to perform cutting, bending, and Lüder’s bands can be eliminated by cold-rolling the drawing thickness by 0.5-1.5%. Yupper • “Stamping press” Ylower – Machine tool that performs most sheet metal • Anisotropy operations – Crystallographic and mechanical fibering anisotropy • Grain Size effect on mechanical properties • “Stampings” • Residual Stress, Springback and Wrinkling – Sheet metal products • Testing method – Cupping test – Forming Limit Diagram 3 4 1. Cutting Operation Cutting Operation • Cutting operation – Plastic deformation Punch – Penetration (1/3 thickness) t –Fracture • Shearing using a machine called power Die shear or square shear. c • Blanking – shearing a closed outline Rollover part (desired part called blank) Burnish • Punching – sheared part is slag (or scrap) and remaining stock is a desired part Fracture zone Burr 5 6 part Kwon 1 ME477 Fall 2004 Analysis Die, blank and punch size • Clearance - 4-8% but sometime 1% of thickness For a round blank, – Too small – fracture does not occur requiring more force.
    [Show full text]
  • Metal Forming Process
    METAL FORMING PROCESS Unit 1:Introduction and concepts Manufacturing Processes can be classified as i) Casting ii) Welding iii) Machining iv)Mechanical working v) Powder Metallurgy vi)Plastic Technology etc., In Mechanical working Process the raw material is converted to a given shape by the application of external force. The metal is subjected to stress.It is a process of changing the shape and size of the material under the influence of external force or stress.Plastic Deformation occurs. Classification of Metal Working Processes 1. General classification i. Rolling ii. Forging iii. Extrusion iv. Wire Drawing v. Sheet Metal Forming 2. Based on Temperature of Working i. Hot Working ii. Cold Working iii. Warm Working 3. Based on the applied stress i. Direct Compressive Stress ii. Indirect Compressive Stress iii. Tensile Stress iv. Bending Stress v. Shear Stress Classification of Metal Working based on temperature. Hot working: It is defined as the mechanical working of metal at an elevated (higher) temperature above a particular temperature. This temperature is referred to RCT(Re Crystallization Temperature). Cold Working: It is defined as the mechanical working of metal below RCT. Warm Working: It is defined as the mechanical working of metal at a temperature between that of Hot working and Cold Working. Ingot is the starting raw metal for all metal working process. Molten metal from the furnace is taken and poured into metallic moulds and allowed to cool or solidify. The cooled solid metal mass is then taken out of the mould. This solid metal is referred to as Ingot.This Ingot is later on converted to other forms by mechanical working.
    [Show full text]
  • 1 Intro and Contents
    Steel Buildings Publication No. 35/03 Steel Buildings Publication No. 35/03 Apart from any fair dealing for the purposes of research The British Constructional Steelwork Association or private study or criticism or review, as permitted Limited (BCSA) is the national organisation for the steel under the Copyright Design and Patents Act 1988, this construction industry: its Member companies publication may not be reproduced, stored or undertake the design, fabrication and erection of transmitted in any form by any means without the prior steelwork for all forms of construction in building and permission of the publishers or in the case of civil engineering. Associate Members are those reprographic reproduction only in accordance with the principal companies involved in the purchase, design terms of the licences issued by the UK Copyright or supply of components, materials, services related to Licensing Agency, or in accordance with the terms of the industry. Corporate Members are clients, licences issued by the appropriate Reproduction professional offices, educational establishments which Rights Organisation outside the UK. support the development of national specifications, quality, fabrication and erection techniques, overall Enquiries concerning reproduction outside the terms industry efficiency and good practice. stated here should be sent to the publishers, The British Constructional Steelwork Association Ltd at the The principal objectives of the Association are to address given below. promote the use of structural steelwork; to assist specifiers and clients; to ensure that the capabilities and Although care has been taken to ensure, to the best of activities of the industry are widely understood and to our knowledge, that all data and information contained provide members with professional services in herein are accurate to the extent that they relate to technical, commercial, contractual and quality either matters of fact or accepted practice or matters assurance matters.
    [Show full text]