DOCSLIB.ORG

Asu9c1 Asu12c1 Aou9c1 Aou12c1

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Asu9c1 Asu12c1 Aou9c1 Aou12c1 Models Indoor unit Outdoor unit ASU9C1 AOU9C1 ASU12C1 AOU12C1 CONTENTS SPECIFICATIONS............................ 1 OUTLINEANDDIMENSIONS....................2 REFRIGERANT SYSTEM DIAGRAM...............3 CIRCUIT DIAGRAM ...........................4 CONTROLLERP.C.BOARDLAYOUTS............7 DISASSEMBLY ILLUSTRATION .................10 PARTSLIST................................13 SPECIFICATIONS INDOOR UNIT ASU9C1 ASU12C1 OUTDOOR UNIT AOU9C1 AOU12C1 COOLING CAPACITY (BTU/hr) 9,400 12,200 ELECTRICAL DATA POWER SOURCE (V) 115 115 FREQUENCY (Hz) 60 60 RUNNING CURRENT (A) 9.0 11.1 INPUT WATTS (W) 950 1,250 SEER 11.0 11.0 EER (BTU/hW) 9.9 9.8 MOISTURE REMOVAL pts/hr(ℓ/hr) 2.9(1.4) 3.8(1.8) AIR CIRCULATION-Hi (m3/hr) 510 520 COMPRESSOR Hermetic type, Permanent split condenser, TYPE 2 pole, Single phase, Induction motor CODE 808-005-42W 806-955-42C 115V 60Hz 115V 60Hz REFRIGERANT R-22 (g) 680 1,200 FAN MOTOR POWER SOURCE (V) 115 115 HI-SPEED (r.p.m.) 1,320 1,350 MED-SPEED (r.p.m.) 1,210 1,250 INDOOR UNIT LO-SPEED (r.p.m.) 1,100 1,150 QUIET (r.p.m.) 1,000 1,050 OUTDOOR UNIT (r.p.m.) 795 795 DIMENSIONS HEIGHT inch (mm) 11(280) 11(280) INDOOR UNIT WIDTH inch (mm) 32-1/8(815) 32-1/8(815) DEPTH inch (mm) 7(179) 7(179) HEIGHT inch (mm) 20-7/8(530) 20-7/8(530) OUTDOOR UNIT WIDTH inch (mm) 30-1/2(750) 30-1/2(750) DEPTH inch (mm) 9-7/8(250) 9-7/8(250) WEIGHTS INDOOR UNIT 26/22(12/10) 26/22(12/10) GROSS/NET lbs. (kg) OUTDOOR UNIT 66/62(30/28) 79/75(36/34) – 1 – OUTLINE AND DIMENSIONS Models : ASU9C1 / AOU9C1 ASU12C1 / AOU12C1 Unit : in(mm) INDOOR UNIT 11(280) 32-1/8 (815) 7(179) OUTDOOR UNIT 30-1/2(750) 9-7/8(250) 19-13/32(493) 20-7/8(530) 11-7/32(285) 33/64(13) BOLT PITCH FOR INSTALLATION – 2 – REFRIGERANT SYSTEM DIAGRAM Models : ASU9C1 / AOU9C1 ASU12C1 / AOU12C1 Refrigerant pipe INDOOR UNITφ�9.53mm(3/8")・・・ASU9C1 / AOU9C1 OUTDOOR UNIT φ�12.7mm(1/2")・・・ASU12C1 / AOU12C1 Discharge pipe 3-Way Suction pipe valve Condenser Accumulator Evaporator Comp- Strainer ressor Capillary Capillary joint tube 2-Way valve Refrigerant pipe φ�6.35mm(1/4") – 3 – CIRCUIT DIAGRAM Models : ASU9C1 / AOU9C1 ()LOUVER Z TEST DIFFUSER 12345 M INDOOR UNIT CN3 1 2 3 45 1 2345 THERMISTOR (ROOM TEMP.) BLACK 1 BLACK BROWN RED YELLOW GREEN ORANGE 2 CN5 1 1 THERMISTOR (PIPE TEMP.) 2 2 GRAY 3 3 GRAY 1 4 4 2 CN4 5 5 CN2 6 6 PURPLE 7 7 7 7 BLUE 8 8 STEP MOTOR 6 6 GREEN 9 9 5 5 YELLOW 10 10 4 4 ORANGE 3 3 CN6 RED GRAY PURPLE BLUE 2 2 BLACK WHITE BROWN CONTROL BOARD PRINTED CIRCUIT BOARD(DISPLAY) 1 1 5 4 3 21 5 4 3 21 M 3 3 2 2 (LOUVER U) 1 1 CN1 CN7 1 2 3 456 7 8 9 WHITE BLACK RED 1 2 3 456 7 8 9 FM THERMAL PROTECTOR FAN MOTOR WHITE WHITE WHITE WHITE WHITE WHITE WHITE WHITE RED WHITE WHITE WHITE BLACK RED 1 2 3 45 1 2 1 2 3 45 1 2 1 2 3 456 7 8 9 CN101 CN103 CN104 POWER SUPPLY BOARD POWER RELAY CAPACITOR 34 CN102 ORANGE 2 2 ORANGE 1 1 W101 W103 W104 GREEN WHITE BLACK BLUE BROWN 1234 GREEN /YELLOW TERMINAL G OUTDOOR UNIT WHITE G WHITE 1 WHITE P.T.C. COMPRESSOR RED 2 STARTER WHITE R 3 S FM CM FAN 4 C MOTOR ORANGE WHITE BLACK 5 FAN MOTOR COMPRESSER CAPACITOR RED RED 6 BLUE CAPACITOR OVERLOAD POWER FUSE BLACK RELAY BLACK SUPPLY BLUE GROUND 115V ¥ 60Hz – 4 – Models : ASU12C1 / AOU12C1 ()LOUVER Z TEST DIFFUSER 12345 M INDOOR UNIT CN3 1 2 3 45 1 2345 THERMISTOR (ROOM TEMP.) BLACK 1 BLACK BROWN RED ORANGE YELLOW GREEN 2 CN5 1 1 THERMISTOR (PIPE TEMP.) 2 2 GRAY 3 3 GRAY 1 4 4 2 CN4 5 5 CN2 6 6 PURPLE 7 7 7 7 BLUE 8 8 STEP MOTOR 6 6 GREEN 9 9 5 5 YELLOW 10 10 4 4 ORANGE 3 3 CN6 RED GRAY PURPLE BLUE 2 2 BLACK WHITE BROWN CONTROL BOARD PRINTED CIRCUIT BOARD(DISPLAY) 1 1 5 4 3 21 5 4 3 21 M 3 3 2 2 (LOUVER U) 1 1 CN1 CN7 1 2 3 456 7 8 9 WHITE BLACK RED 1 2 3 456 7 8 9 FM THERMAL PROTECTOR FAN MOTOR WHITE WHITE WHITE WHITE WHITE WHITE WHITE WHITE RED WHITE WHITE WHITE BLACK 1 2 3 45RED 1 2 1 2 3 45 1 2 1 2 3 456 7 8 9 CN101 CN103 CN104 POWER SUPPLY BOARD POWER RELAY CAPACITOR 34 CN102 ORANGE 2 2 ORANGE 1 1 W101 W103 W104 GREEN WHITE BLACK BLUE BROWN 1234 GREEN /YELLOW TERMINAL G OUTDOOR UNIT WHITE G WHITE 1 WHITE COMPRESSOR RED 2 R 3 S FM CM FAN 4 C MOTOR ORANGE BLACK 5 FAN MOTOR COMPRESSER CAPACITOR RED RED 6 BLUE CAPACITOR OVERLOAD POWER FUSE BLACK RELAY BLACK SUPPLY BLUE GROUND 115V ¥ 60Hz – 5 – Models : ASU9C1 INDOOR PRINTED CIRCUIT BOARD ASU12C1 CIRCUIT DIAGRAM 115V AC 60Hz TERMINAL BOARD JUMPER WIRE MAIN PCB 123 EZ-09903WSE-C CONTROLLER PCB ASSEMBLY (MAIN PCB) (GM-60187) ASU9C1 : EZ-09903WSE-C (GM-60187) EZ-09904WSE-C ASU12C1 : EZ-09904WSE-C (GM-60188) (GM-60188) : Disconnect : Connect FILTER PCB ASSEMBLY BLUE BLACK WHITE BROWN EZ-09903WSE-P (GM-60164) WHITE ROOM TEMPERATURE WHITE THERMISTOR BLACK BLACK PIPE TEMPERATURE THERMISTOR GRAY GRAY GREEN RED WHITE WHITE WHITE WHITE WHITE INDICATOR PCB EZ-09903HSE-D BROWN WHITE RED ORANGE PURPLE BLUE OPERATERED GREEN TIMER GRN YELLOW SIWING ORG RED BLACK BLACK WHITE BROWN WHITE RED RED ORANGE LOUVER-Z FAN MOTOR YELLOW (DIFFUSER) GREEN BLUE PURPLE GRAY MODEL CHANGING LOUVER-U CODE WHITE BLACK AUTO CHANGE OVER WHITE WHITE HEATING TEMPERATURE CORRECTION SWITCHING THERMAL FUSE AUTO RESTART REMOTE CONTROL CUSTOM CODE ORANGE ORANGE RESERVE FAN CAPACITOR FAN – 6 – ASU12C1 Models :ASU9C1 ASU12C1 Models :ASU9C1 R1 K D2 S1 R11 100K 33 A VDD RESET 29 220 2.2 F+ 0.1 F + 47 F 0.1 F 22 0.1 F DC3V C1 D9 C3 C16 D1 C2 23 C15 32 D10 VSS 38 D11 R5 2(1/4W) IC1 R4 100 REMOTE CONTROLUNIT 37 A D12 C LED1 5 P00 28 R2 B K CARR Q1 B K13 K5 K1 C 6 CIRCUIT DIAGRAM S2 P01 1K Q2 E K6 K2 7 R3 22K S3 P02 E K11 K3 8 36 R10 P03 VLC3 K12 K4 0 C8 C9 C10 C11 45 SEG0 150P x 4 46 13 SEG1 D0 SEG2 47 14 D1 15 D2 – 9 – LCD 16 SEG30 75 D3 Jumper Wire Function Selection 9 41 P10(J5) COM0 No. Functions Set up J6 0 10 42 P11(J6) COM1 J1 Change of remote control type L J2A 0 J7 0 11 COM2 43 P12(J7) J2 Change of transmitting code H J2B 0 J8 0 12 18 P13(J8) D5 J3 Heating mode L J3A 0 17 19 No. KEYPADS D4 D6 J4 24H / 12H selector L J3B 0 20 D7 K1 START/STOP J5 Dry mode H J4A 0 24 P20(J1) 39 K2 MASTER CONTROL J6 Temperature display of automatic operation H J4B 0 25 (J14)P31 P21(J2) 40 K3 SET TEMP.(+), SET TIME(+) J7 Change of switch H J9A 0 26 (J15)P30 P22(J3) K4 SET TEMP.(-), SET TIME(-) J8 Change of timer function L 27 J9B 10K P23(J4) K5 FAN CONTROL J9 Change of switch L 1 P40(J9) K6 AIR FLOW DIRECTION J10 Fan mode H 2 P41(J10) R8 910 kHz 31 C4 100P 3 XOUT J11 Power selector H P42(J11) J12A 0 4.7K X2 J12 Quiet L 4 P43(J12) 100P XIN 30 C5 J13 Display change of automatic operation L J12B 10K 21 D8(J13) 34 R9 18P XcOUT C6 680K L: Connected to X1 K11 SWING LOUVER J13A 0 C12 C13 C18 C19 C21 C22 C7 18P H: Connected to XcIN 35 K12 TIMER J13B 0 150P x 6 32.768 kHz K13 SLEEP VC1 S1 ACL S2 TIME ADJUST S3 TEST RUN DISASSEMBLY ILLUSTRATION Models : ASU9C1 Models : ASU12C1ASU9C1 ASU12C1 63 240 74 759 777 – 10 – 108 401 146 189 133 169 B 26 158 962-1 109 D 796 963 764 69 C – 11 – 89 323 268 962-2 178 652-1 41 184-1 217 178 64 127 E 557 96 815 93 875 H 32-2 95 94 32-1 G 236 102 32-3 F 273 92 281 876-2 960 873 65 876-1 767-1 440 527 A A 734 138 A 38 815 34 51 64 32-2 373 109 – 12 – 9 419 412 744 413 824 823 16 98 5 745 2 41 899 941 46 55 42 213 4 198 420 12 39 107 940 14 A 7 13 46 ASU9C1/AOU9C1 ASU12C1/AOU12C1 PARTS LIST When you order parts, please make a photocopy of this page INDOOR UNIT [ASU9C1/ASU12C1] and fill the number of the parts in the "Order" column. Ref. Part No. Part No. Ref. Part No. Part No. Order Order Order Order Description Description Q'ty Q'ty Q'ty Q'ty No. ASU9C1 ASU12C1 No. ASU9C1 ASU12C1 26 BR Sheet 40x80xT5 9305039043 ← 240 Remote Control 9309143012 ← 32-1 Control Box-A 9309045019 ← Unit AR-FB2 32-2 Control Box-B 9309046016 ← 268 Motor Cover-B 9306582012 ← 32-3 Control Box-C 9309055018 ← 273 Lamp Cover Holder 9309048010 ← 41 Fan Motor Assy-IN 9600881019 ← 281 Clamp Metal(Pipe) 9306607012 ← 63 Front Panel Assy w/o Filter 9306817176 ← 323 Louver-B 9306584016 ← 64 Capacitor 9700468066 ← 401 Wall Hook Bracket 9306588014 ← (Fan Motor)5.7μF/200V ← 440 Flow Control 9306570019 ← 65 Flow Control 9306571016 ← Panel-U Panel-Z ← 557 Diffuser Spring 9306611019 ← 69 Louver-A 9306583019 ← 652-1 Thermistor Holder 313714262805 ← 74 Filter 9306601010 ← Pipe 89 Casing Fixture 9307018008 ← 759 Intake Grille 9307130052 ← 92 Link Plate 9306577018 ← 764 Drain Cap Assy 9304150008 ← 93 Link-A 9306573010 ← 767-1 Bottom Cover-A 9306567019 ← 94 Link-B 9306574017 ← 777 Intake Grille 9306755010 ← 95 Link-C 9306575014 ← Clamp 96 Link-D 9306576011 ← 796 Control Box-D 9309049017 ← 102 Link Spring 9306610012 ← 815 Terminal 9703455018 ← 108 Base 9306566012 ← 873 Lamp Cover 9306593025 ← 109 Casing 9306569013 ← 875 Filter PCB Assy 9703434013 ← 127 Drain Hose Assy 9305550029 ← EZ-09903WSE-P 133 Evaporator Cover 9306606015 ← 876-1 Step Motor 9305780006 ← 146 Evaporator Assy 9308200013 ← 876-2 Step Motor 9305892006 ← 158 Connecting Pipe 9309515017 9308100016 960 Diffuser 9306572013 ← Assy 962-1 Guard Holder-L 9307229015 ← 169 Cross-flow Fan 9307836015 ← 962-2 Guard Holder-R 9307228018 ← Assy 963 Fan Guard Metal 9305751020 ← 178 Motor Cushion-A 9303528006 ← Rod (Fan Motor) B Screw(w/Spring 184-1 Thermistor Spring 313728262708 ← Washer) -A C Control BoxAssy 9309044012 ← 189 Shaft Holder-C 930628017 ← D Control BoxCover A 9309039018 ← 217 Capacitor Holder 9309047013 ← E Control BoxCover B 9309040014 ← 236 Controller PCB 9703433016 9703433023 F Control BoxCover C 9309041011 ← Assy G Control BoxCover D 9309042018 ← H Conduit Holder 9309043015 ← ←：Same as left ←：Same as left OUTDOOR UNIT [AOU9C1/AOU12C1] Ref.
Load more

Recommended publications
  • Airflow Simulations Around OA Intake Louver with Electronic Velocity
    Airflow Simulations around OA Intake Louver with Electronic Velocity Sensors Hwataik Han*1, Douglas P. Sullivan2 and William J. Fisk3 1 Professor, Kookmin University, Korea 2 Research Associate, Indoor Environment Department, Lawrence Berkeley National Laboratory, USA 3 Director, Indoor Environment Department, Lawrence Berkeley National Laboratory, USA Abstract It is important to control outdoor airflow rates into HVAC systems in terms of energy conservation and healthy indoor environment. Technologies are being developed to measure outdoor air (OA) flow rates through OA intake louvers on a real time basis. The purpose of this paper is to investigate the airflow characteristics through an OA intake louver numerically in order to provide suggestions for sensor installations. Airflow patterns are simulated with and without electronic air velocity sensors within cylindrical probes installed between louver blades or at the downstream face of the louver. Numerical results show quite good agreements with experimental data, and provide insights regarding measurement system design. The simulations indicate that velocity profiles are more spatially uniform at the louver outlet relative to between louver blades, that pressure drops imposed by the sensor bars are smaller with sensor bars at the louver outlet, and that placement of the sensor bars between louver blades substantially increases air velocities inside the louver. These findings suggest there is an advantage to placing the sensor bars at the louver outlet face. Keywords: ventilation; outdoor
    [Show full text]
  • Performance Measurements of a Unique Louver
    Performance Measurements Grant O. Musgrove Southwest Research Institute, of a Unique Louver Particle San Antonio, TX 78238 e-mail: [email protected] Separator for Gas Turbine Engines Karen A. Thole Mechanical and Nuclear Engineering Department, Solid particles, such as sand, ingested into gas turbine engines, reduce the coolant flow The Pennsylvania State University, in the turbine by blocking cooling channels in the secondary flow path. One method to University Park, PA 16802 remove solid particles from the secondary flow path is to use an inertial particle separa- tor because of its ability to incur minimal pressure losses in high flow rate applications. In this paper, an inertial separator is presented that is made up of an array of louvers Eric Grover followed by a static collector. The performance of two inertial separator configurations was measured in a unique test facility. Performance measurements included pressure Joseph Barker loss and collection efficiency for a range of Reynolds numbers and sand sizes. To comple- ment the measurements, both two-dimensional and three-dimensional computational United Technologies Corporation – results are presented for comparison. Computational predictions of pressure loss agreed Pratt & Whitney, with measurements at high Reynolds numbers, whereas predictions of sand collection East Hartford, CT 06108 efficiency for a sand size range 0–200lm agreed within 10% of experimental measure- ments over the range of Reynolds numbers. Collection efficiency values were measured to be as high as 35%, and pressure loss measurements were equivalent to less than 1% pres- sure loss in an engine application. [DOI: 10.1115/1.4007568] Introduction operating principle of inertial separators is to cause the particle- laden flow to abruptly change trajectory, whereby the particles do Aircraft gas turbines ingest solid particles during takeoff, land- not react to the change in flow direction due to their larger inertia ing, and while flying in dusty environments.
    [Show full text]
  • High Performance House Best Practices Guide
    New York State Energy Research & Development Authority High Performance House Best Practices Guide Design Intelligence for Energy Performance in Single Family Homes TABLE OF CON T EN T S High Performance House 1.1 Initial Work................................... 3 1.2 Process.......................................... 4 1.3 Testing........................................... 4 1.3.1 Building Construction.............................. 4 1.3.2 Building Form and Siting......................... 5 1.3.3 Passive Sustainable Strategies................ 6 1.3.4 Active Sustainable Strategies................... 14 1.4 Conclusions................................... 14 1.4.1 Additional Recommendations.................. 15 2 1.1 INitiAL WORK 1.1 Initial Work ON cti Preliminary analysis looked purely at geometric implications on energy use. This theoretical investigation tested a variety of building forms and found two general guidelines that govern performance. Across all building manipulations, results showed that forms minimizing volume and RODU T maximizing southern exposure perform best. This lines with rational thought; increased volume N increases the volume of required conditioned space, while maximizing southern exposure allows I for greatest winter solar gains and daylighting. Following this study, energy analysis was given for three, previously conceived housing designs – “Slope House”, “Underground House” and “X House”. In all cases, formal design (siting, building form, orientation) were given, fixed parameters. This proved a challenge to the energy optimization of the house. For the “Slope House”, building volume opens to the west without the benefit of southern expo- sure on the open face. Passive solar gains were minimal, with excessive shading on south facing windows. The majority of glazing is to the north, which effectively cuts the building’s thermal resistance/storage without the offsetting solar gains received on southern exposures.
    [Show full text]
  • Damper Application Guide 1.” 1 Common 2 2 + Hot
    Control of Dampers ®® INDEX I. INTRODUCTION A. Economizer Systems ............................................................................................................ 3 B. Indoor Air Quality ...................................................................................................................3 C. Damper Selection ..................................................................................................................3 II. DAMPER SELECTION A. Opposed and Parallel Blade Dampers ..................................................................................3 B. Flow Characteristics...............................................................................................................4 C. Damper Authority ..................................................................................................................4 D. Combined Flow ......................................................................................................................6 III. ADDITIONAL CONSIDERATIONS A. Economizer Systems .............................................................................................................6 B. Building Pressure ...................................................................................................................8 C. Mixed Air Temperature Control ..............................................................................................8 D. Actuators - General ................................................................................................................8
    [Show full text]
  • IAQ Economizer LOGIC BOX
    IAQ Economizer LOGIC BOX Split-system Economizing/Indoor Air Quality/CO Alarm Activated Works on forced air systems, with or without air conditioning installed Enables cost saving cooling strategy: Expensive mechanical cooling can be set at a higher temperature Fresh Air Cooling can be set at a lower temperature Supports a variety Indoor Air Quality configurations: Continuous introduction Timed introduction CO2 or VOC sensor activated introduction Provides alarm activated fresh air introduction supporting CO or other alarm installations Occupant interface provides easy override, along with readiness, damper and fault status, (continuous fault detection) Operational tests can be conducted from within the conditioned space Quick connect wiring harnesses provide fast, correct termination FRESH AIR MANUFACTURING CO. FAMCO IAQ Economizer Famcoiaq.com 649 N. Ralstin St., Meridian, ID 83642 * (208)884-8931 * (800)-234-1903 * FAX: (208)884-8943 IAQ Economizer ECONOMIZER SYSTEM Damper Actuator Exhaust Damper Transformer Thermostat Logic Literature Box Cables Damper Box Actuator – Honeywell MS8105A1030, 24 VAC, 44 lb-in torque Outdoor thermostat- Dayton RLZ94A Nema 4X, Range 30º-110º F Transformer – RIB Functional Devices, Inc. TR50VA005 , 50VA All required System Cables are provided: • Power 40’ • Furnace 40’, plenum rated, HVAC industry standard color coding for furnace board termination • Damper Box 50’, plenum rated • Outdoor thermostat, 70’ , shielded, non polarity sensitive FRESH AIR MANUFACTURING CO. FAMCO IAQ Economizer
    [Show full text]
  • Building Applications, Opportunities and Challenges of Active Shading Systems: a State-Of-The-Art Review
    energies Review Building Applications, Opportunities and Challenges of Active Shading Systems: A State-Of-The-Art Review Joud Al Dakheel and Kheira Tabet Aoul * ID Architectural Engineering Department, United Arab Emirates University, P.O. Box 15551 Al Ain, UAE; [email protected] * Correspondence: [email protected]; Tel.: +971-566-433-648 Academic Editor: Arman Hashemi Received: 28 June 2017; Accepted: 4 August 2017; Published: 23 October 2017 Abstract: Active shading systems in buildings have emerged as a high performing shading solution that selectively and optimally controls daylight and heat gains. Active shading systems are increasingly used in buildings, due to their ability to mainly improve the building environment, reduce energy consumption and in some cases generate energy. They may be categorized into three classes: smart glazing, kinetic shading and integrated renewable energy shading. This paper reviews the current status of the different types in terms of design principle and working mechanism of the systems, performance, control strategies and building applications. Challenges, limitations and future opportunities of the systems are then discussed. The review highlights that despite its high initial cost, the electrochromic (EC) glazing is the most applied smart glazing due to the extensive use of glass in buildings under all climatic conditions. In terms of external shadings, the rotating shading type is the predominantly used one in buildings due to its low initial cost. Algae façades and folding shading systems are still emerging types, with high initial and maintenance costs and requiring specialist installers. The algae façade systems and PV integrated shading systems are a promising solution due to their dual benefits of providing shading and generating electricity.
    [Show full text]
  • BIM Handbook
    BIM Handbook A Guide to Building Information Modeling for Owners, Managers, Designers, Engineers, and Contractors Chuck Eastman Paul Teicholz Rafael Sacks Kathleen Liston John Wiley & Sons, Inc. BIM Handbook: A Guide to Building InformationModeling for Owners, Managers,Designers, Engineers, and Contractors. Chuck Eastman, Paul Teicholz, Rafael Sacks and Kathleen Liston Copyright © 2008 John Wiley & Sons, Inc. ffirs.indd i 1/3/08 12:32:13 PM This book is printed on acid-free paper. ϱ Copyright © 2008 by John Wiley & Sons, Inc. All rights reserved Published by John Wiley & Sons, Inc., Hoboken, New Jersey Published simultaneously in Canada No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, scanning, or otherwise, except as permitted under Section 107 or 108 of the 1976 United States Copyright Act, without either the prior written permission of the Publisher, or authorization through payment of the appropriate per-copy fee to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, (978) 750-8400, fax (978) 646-8600, or on the web at www.copyright.com. Requests to the Publisher for permission should be addressed to the Permissions Department, John Wiley & Sons, Inc., 111 River Street, Hoboken, NJ 07030, (201) 748-6011, fax (201) 748-6008, or online at www.wiley.com/go/permissions. Limit of Liability/Disclaimer of Warranty: While the publisher and the author have used their best efforts in preparing this book, they make no representations or warranties with respect to the accuracy or completeness of the contents of this book and specifi cally disclaim any implied warranties of merchantability or fi tness for a particular purpose.
    [Show full text]
  • Studio Education for Integrated Practice Using
    STUDIO EDUCATION FOR INTEGRATED PRACTICE USING BUILDING INFORMATION MODELING A Dissertation by OZAN ÖNDER ÖZENER Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY December 2009 Major Subject: Architecture STUDIO EDUCATION FOR INTEGRATED PRACTICE USING BUILDING INFORMATION MODELING A Dissertation by OZAN ÖNDER ÖZENER Submitted to the Office of Graduate Studies of Texas A&M University in partial fulfillment of the requirements for the degree of DOCTOR OF PHILOSOPHY Approved by: Chair of Committee, Mark J. Clayton Committee Members, Robert E. Johnson Wei Yan José L. Fernández-Solís Head of Department, Glen Mills December 2009 Major Subject: Architecture iii ABSTRACT Studio Education for Integrated Practice Using Building Information Modeling. (December 2009) Ozan Önder Özener, B.Arch., Istanbul Technical University; M.Arch., Istanbul Technical University Chair of Advisory Committee: Dr. Mark J. Clayton This research study posits that an altered educational approach to design studio can produce future professionals who apply Building Information Modeling (BIM) in the context of Integrated Project Delivery (IPD) to execute designs faster and produce designs that have demonstrably higher performance. The combination of new technologies and social/contractual constructs represents an alternative to the established order for how to design and how to teach designers. BIM emerges as the key technology for facilitating IPD by providing consistent, computable and interoperable information essential to all AEC teams. The increasing trend of BIM adoption is an opportunity for the profession to dramatically change its processes and may potentially impact patterns of responsibility and the paradigms of design.
    [Show full text]
  • Flow, Heat Transfer, and Pressure Drop Interactions in Louvered-Fin Arrays
    Flow, Heat Transfer, and Pressure Drop Interactions in Louvered-Fin Arrays N. C. Dejong and A. M. Jacobi ACRC TR-I46 January 1999 For additional information: Air Conditioning and Refrigeration Center University of Illinois Mechanical & Industrial Engineering Dept. 1206 West Green Street Prepared as part ofACRC Project 73 Urbana. IL 61801 An Integrated Approach to Experimental Studies ofAir-Side Heat Transfer (217) 333-3115 A. M. Jacobi, Principal Investigator The Air Conditioning and Refrigeration Center was founded in 1988 with a grant from the estate of Richard W Kritzer, the founder of Peerless of America Inc. A State of Illinois Technology Challenge Grant helped build the laboratory facilities. The ACRC receives continuing support from the Richard W. Kritzer Endowment and the National Science Foundation. The following organizations have also become sponsors of the Center. Amana Refrigeration, Inc. Brazeway, Inc. Carrier Corporation Caterpillar, Inc. Chrysler Corporation Copeland Corporation Delphi Harrison Thermal Systems Eaton Corporation Frigidaire Company General Electric Company Hill PHOENIX Hussmann Corporation Hydro Aluminum Adrian, Inc. Indiana Tube Corporation Lennox International, Inc. rvfodine Manufacturing Co. Peerless of America, Inc. The Trane Company Thermo King Corporation Visteon Automotive Systems Whirlpool Corporation York International, Inc. For additional information: .Air.Conditioning & Refriger-ationCenter Mechanical & Industrial Engineering Dept. University ofIllinois 1206 West Green Street Urbana IL 61801 2173333115 ABSTRACT In many compact heat exchanger applications, interrupted-fin surfaces are used to enhance air-side heat transfer performance. One of the most common interrupted surfaces is the louvered fin. The goal of this work is to develop a better understanding of the flow and its influence on heat transfer and pressure drop behavior for both louvered and convex-louvered fins.
    [Show full text]
  • Facilities Standards for the Public Buildings Service (PBS-PQ100.1)
    CHAPTER 1. GENERAL REQUIREMENTS Facilities Standards for the Public Buildings Service (PBS-PQ100.1) Arrangement of Chapters Chapter 1: General Requirements Appendix 1.A: Life Cycle Cost Example Chapter 2: Site Planning and Landscape Design Chapter 3: Architectural and Interior Design Chapter 4: Structural Engineering (Includes Seismic Design) Chapter 5: Mechanical Engineering Chapter 6: Electrical Engineering Appendix 6.A: Energy Efficient Design of New Buildings Chapter 7: Fire Protection Engineering Chapter 8: Security Design Index PBS-PQ100.1 June 14, 1996 Page i FACILITIES STANDARDS FOR THE PUBLIC BUILDINGS SERVICE CHAPTER 1 GENERAL REQUIREMENTS Purpose of the Facilities Standards for the Public Buildings Service ......................................................................................................... 1 Arrangement of Chapters.................................................................................... 3 Applicability of the Facilities Standards ........................................................................ 4 GSA Building Types .......................................................................................... 4 Office Buildings...................................................................................... 4 Courts...................................................................................................... 4 Border Stations........................................................................................ 4 Child Care Centers.................................................................................
    [Show full text]
  • Louver Products Severe Duty, Stationary, Operable
    Louver Products Severe Duty, Stationary, Operable November 2017 Louver Selection Guide In an effort to help located and select the louver you need, this catalog organizes the more than 100 standard Greenheck louver models into easily navigated categories, organized by your application requirements. Conventional Application Louvers Fixed Blade These conventional fixed blade louvers are among our most popular. All shown are AMCA Licensed for Air EDJ-401 Performance and Water Penetration and may be applied 4-inch depth in conventional intake or exhaust applications where Stationary provisions to manage water are present or some nuisance Drainable Head weather infiltration is acceptable or accounted for. These Extruded Aluminum louvers shown are among the most economical options. J-Blade ESJ-401 ESD-435 4-inch depth 4-inch depth Stationary Stationary Non-Drainable Drainable Blades Extruded Aluminum Drainable Head J-Blade Extruded Aluminum 56% Free Area ESJ-602 ESD-635 6-inch depth 6-inch depth Stationary Stationary Non-Drainable Drainable Blades Extruded Aluminum Drainable Head J-Blade Extruded Aluminum 59% Free Area 2 Louver Selection Guide Wind Driven Rain Louvers Fixed Blade These high performance wind driven rain fixed blade louvers are among our most popular. All shown are AMCA Licensed for Air Performance, Water Penetration and Wind Driven Rain and may be applied in intake or exhaust applications where provisions to manage water are limited. Wind Driven Rain louvers offer far superior protection against driving rain when compared to conventional louvers. Horizontal blade wind driven rain louvers perform extremely well, but vertical blade products offer the best performance considering both weather resistance and airflow performance.
    [Show full text]
  • Passive Building Design Guide: Multifamily Construction Copyright 2018 Passive House Institute US, All Rights Reserved
    Passive Building Design Guide FOR DEVELOPERS, INVESTORS & CONSTRUCTION PROFESSIONALS MULTIFAMILY CONSTRUCTION ACKNOWLEDGEMENTS We would like to thank the MacArthur Foundation for making this design guide and its associated website, the Multifamily Construction Resource Center (www.multifamily.phius.org), possible. Through these new resources, they do vital work building a more just verdant, and peaceful world, specifically through slashing the effects of global climate change. We thank them for their investment and commend them for acting locally on issues with global implications. We would also like to thank all of the people who worked with us to put this guide together. Their help tracking down photos, photo credits, providing technical insight, and inside information was invaluable and has made this a better book. Among the people who dropped everything to help: Sam Rodell, Erin Cooperrider, Dylan Lamar, Matt Fine, HousingUp, REACH CDC, Community Housing of Maine, Tinsley Morrison, Vickey Rand, Ben Walter, Colin Schless, Michael Hindle, Steve Bluestone, Hammer and Hand, Ben Bogie, James Hartford, Hank Keating, and last—but not least—Sloan Ritchie. Passive Building Design Guide: Multifamily Construction Copyright 2018 Passive House Institute US, all rights reserved. CONTENTS Introduction 4 Passive Building Fundamentals 5 �� Passive Building Benefits 6 Detail drawings eliminate weak links. �� 8 10 Great windows make rooms bigger. Passive Building Works for D A RE RCH TE I S T I E GMICHAEL WILLIAM CLINEC T E R C D 15 5/23/2014 2:38:40 PM S PORTLAND, OREGON A4.25 R 61CC T N 4 12 A #2987 O T E G E OF O R all Building Types ™ T.O PLATE AT BRICK 136' - 8" 6720 SW MACADAM AVENUE, SUITE 100 PORTLAND, OR 97219 6111 T 503-245-7100 4 117 SOUTH MAIN STREET, SUITE 400 �� SEATTLE, WA 98104 T 206-576-1600 12 R 61GC © ANKROM MOISAN ARCHITECTS, INC.
    [Show full text]