STAIR AND RAIL FASTENERS INSTALLATION INSTRUCTIONS
A. A simple method with open tread is to B. SURE-TITE Newel Fasteners are C. Newel post fastener plate provides D. Newel posts can also be STEP 1 utilize our unique newel attaching hardware one of the most secure methods of quick and easy installation. This heavy notched and secured to bottom (comes complete with instructions). Attach- mounting newel posts to finished 3/16” steel plate can be used under riser or foot of half wall. Half ATTACHING NEWEL POSTS ing hardware can be used where newels are floors. It uses floor joists for support, carpet, over concrete or finished floors. newel posts or rosettes should free standing or attached against stairs. needs additional framing and installs in (comes complete with instructions) be used against a wall. This is the “anchor” of your stairway and care as little as 10 minutes. (comes complete must be taken to assure proper secure attach- with instructions) ment and placement of all newels. Trim newel post to required height (as per local building code). Depending on the type of construction L Bracket Post Fasteners there are many ways in which newel posts may be attached.
Interior Stair Parts [ Turning out style ]
Rail Bolt Fastener Rail Post Fastener Rail Bolt Wrench A. It is best to cut railing to B. Attach handrail to newel STEP 2 size and angle after newel posts post as shown. Similarly cut have been installed. Simply and install bottom rail where ATTACHING RAILING place railing against base of required. newel post and mark angle of line for cutting. C. Rail and post fasteners can D. Rail bolt fasteners are be used to fasten handrails to best used to fasten handrails newel posts and/or newel posts flush to newel post. (comes to stair risers. (comes complete complete with instructions) with instructions)
NOTE: Rail-bolt wrench is available for all Newel Post Fastener SURE-TITE Baluster Fastening Kit above applications Newel Fastening System
A. Channeled Rail – Hold spindle tight against newel post B. Non-Channeled Rails – This application making sure the turned area is centred. Mark angle with requires precise cutting as the spindle is pencil guided by the top and bottom rails. This gives you attached directly to the rail. Pre-drilling, STEP 3 correct angle and height. Be sure to add 3/16” (5mm) to screwing and plugging hole is usually required. ATTACHING WOOD SPINDLES allow for depth of slot in each rail. DO NOT CUT TOO SHORT!
C. Hardware such as baluster fasteners are available to ease installation Install spindles one at a time, alternately and add strength to spindle/ with fillets. Then apply adhesive to both rail application. (comes ends of spindle and place in channel. complete with instructions) Apply adhesive to fillet and insert in channel before positioning next spindle. Finally secure spindles and fillets with finishing nails. www.bhwoodturning.com NEWELS BOX NEWELS TREADS & RISERS
Oak/Maple Qwik Tread Stair Riser Material RH / LH Stair-end Straight Wall End c/w Riser
Available in Available in 48” & 60” 48”/60” lengths 4½” & 6” widths
SPINDLES 56 ” Oak / Maple Tread Oak / Maple Tread Nosing Stair End Profile After applied moulding kit. Classic Classic Colonial Heritage Heritage Triple Fluted Dover Shaker Raised Panel RTNP USNP RTNP RTNP USNP Post Post Post Post RAILINGS
6 ¼" Recessed Panel Post (Primed, Poplar, Oak & Maple)
Available in 36”/42” lengths Note: Available in Packaged with 48” & 60” 48”/60” lengths two cap options 2 ⁷/₈” 2 ⁷/₈” 2 ⁷/₈” 2 ¼” Wall Rail 2 x 4 / 2 x 6 2 x 4 / 2 x 6 Dado 1 ⁵/₈” Dado ½” Bullnose Bullnose w/ finger groove includes Reveal cap
Available in 3 ½” width Mushroom Small Large Crown Small Crown 2 ¾ " Modern 2 1/₈” Modern Classic Dowel Top Classic Colonial Heritage Raised Panel Double Square Mushroom* Wall Rail* Wall Rail* Corner Flute Corner Flute Corner Flute Double Flute Double Flute Double Flute Post Fluted Post Post RTNP USNP SONP RTNP USNP SONP
ACCESSORIES STRINGER CAP
Available in 36”/42” lengths Available in 48”/60” lengths
Fancy Cap Econo Cap Oval Rosette 1” x 4” Bottom Plate 1” x 6” Bottom Plate 1 ⁵/₈” Fillet ½” Fillet
Corner Double Square 1 ¼” Square Craftsman Craftsman Craftsman Square Square Square Raised Round Rosette Wood Bracket 3 ¼" Metal Brackets 3” x 1 ¼” 2 ⁷/₈” x ¾” 2 ⁷/₈” x ¾” 1” x 4” Bottom Plate Flute Flute (Primed) 1V Groove 2V Groove SONP RTNP USNP SONP Panel Available in nickel, dull chrome, 1 ⁵/₈ Dado 1 ⁵/₈ Dado ½ Dado with corner groove SONP black, oil rubbed bronze
All wood products available in Hemlock, Oak, Poplar and Maple. Other species available upon request *please contact for availablity