Mia 4 Poster Bed

Assembly Instructions - Please keep for future reference White 2627436 Pink 2557386

Dimensions

Width : 197.3 cm Depth : 99.5 cm Height: 186.2 cm

Assembly Instructions - Please keep for future reference

If you need help or have damaged or missing parts, call the Argos Customer Helpline: 0845 640 30 30

350268-01 Issue 1 - 26-05-2014 ! Safety and Care Advice Important - Please read these instructions fully before starting assembly

• Check you have all the • Do not stand or put weight on components and tools listed on the product, this could cause pages 2 and 3. damage.

• Remove all fittings from the • Assemble the item as close to plastic bags and separate them its final position (in the same into their groups. room) as possible. • We do not recommend the use of power drill/drivers for • Keep children and animals • Assemble on a soft level inserting screws, as this could away from the work area, small surface to avoid damaging the damage the unit. Only use hand parts could choke if swallowed. unit or your floor. screwdrivers.

• Make sure you have enough • Parts of the assembly will be • Dispose of all packaging space to layout the parts before easier with 2 people. carefully and responsibly. starting.

Care and maintenance

• Only clean using a damp cloth • From time to time check that • This product should not be and mild detergent, do no use there are no loose screws on discarded with household waste. bleach or abrasive cleaners. this unit. Take to your local authority waste disposal centre.

Note ! • This childs bed conforms to BS 8509:2008 +A1:2011.

• Age recommendation: from 3 year to 12 years.

• Mattress in size 90x190 cm to be used with this bed.

• Children are likely to play, bounce ,jump and climb on beds, therefore the childs bed should not be placed too close to other furniture or windows, and should be placed either tight to any wall or have a gap 300mm between the wall and the side of bed.

• Any additional or replacement parts are obtained from the manufacturer or distributor.

Note: if required the next page can be cut out and used as reference throughout the assembly. Keep this page with these instructions for future reference.

1 If you have damaged or missing components, call Components - Panels the Argos Customer Helpline: 0845 640 30 30 Please check you have all the panels listed below

1 Post, headboard x 2 (182,4 cm x 5 cm)

2 Post, foot (182,4 cm x 5 cm)

4 Footboard (89,5 cm x 54,5 cm)

3 Headboard (89,5 cm x 64 cm)

5 Side rail x 2 7 Slat (189,7 cm x 14,5 cm) (91,8 cm x 6,8 cm)

6 Spacer block (7,1 cm x 2,2 cm)

10 Drawerside, right (41,3 cm x 14,5 cm) 9 Drawerside, left 8 Drawer front (41,3 cm x 14,5 cm) (189,1 cm x 19,7 cm)

11 Drawerback (186,5 cm x 14,5 cm)

13 Drawer rail x 2 12 Drawer bottom (40,0 cm x 6 cm) (187,5 cm x 41,0 cm)

14 Top rail, side x 2 15 Top rail, end x 2 (197,3 cm x 3,8 cm) (91,9 cm x 3,8 cm) 350268-03 2 Components - Fittings Please check you have all the panels listed below

Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.

Aa Bo Bv

ø7.8 x 40mm Wooden dowel x 20 ø3 x 12mm Screw x 24 ø3,5 x 30mm Screw x 28 Ca Cb Ec

ø15 x 10.5mm Cam x 12 ø5 x 8, cc34mm Bolt x 12 ø35mm Cap x 4 Fm Hg Hw

ø35mm Bracket x 4 M6 x 70mm Threaded rod x 4 M6 x 80mm Bolt x 12 Ke Na Ne

ø6.1 x 11.5mm Screw x 8 M6 x 10mm Nut x 4 M6 x 20mm Bushing x 4 Nf Ta Vn

M6, ø10 x 12.5mm barrel nut x 12 ø35mm Wheel x 4 Angle 23 x 23 x 24mm x 4 Vq Ya Yb

70 x 70 x 16mm Corner angle x 4 4mm Allen key x 1 10/13mm Wrench x 1 Yc

6mm Allen key x 1

Tools required

Phillips screwdriver Hammer (Medium & large)

Flatblade screwdriver (Medium)

Ruler - Use this ruler to help correctly identify the screws 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

3 350268-04 Assembly Instructions Step 1 Assembly of the bed. 15 14 1 14

15 1

3 7 x 14 2 5

5 4

Step 1.1 Aa

Knock the dowels Aa into Aa ø7.8 x 40mm Wooden dowel x 8 the holes indicated on the side rails 5 using a small hammer. 5 x 2

Aa Step 1.2 Ne Yc

Screw the bushings Ne into M6 x 20mm Bushing x 4 6mm Allen key x 1 the holes indicated on the posts 1 and 2 .

Use the allen key Yc .

Ne 1 x 2

Ne 2 x 2

350268-05 4 Assembly Instructions

Step 1.3 Hw Nf

Fix the posts 1 onto the headboard 3 using bolts M6 x 80mm Bolt x 8 M6, ø10 x 12.5mm barrel nut x 8 Hw into the barrel nuts Nf . Ya Note - the holes in the posts for the siderails must point 4mm Allen key x 1 downwards.

Note NO holes ! The holes for the 1 siderails on reverse side ! Nf Hw

1 Nf Hw Nf 3

Fix the posts 2 onto the Hw Nf footboard 4 using bolts Hw into the barrel nuts Nf . Hw

Make sure to place the legs 2 onto the footboard 4 exactly as shown. Note the holes for the siderails must point upwards.

Use the allen key Ya . Note the holes for the siderails !

Nf Hw

2 Hw Nf Nf 4

Nf Hw

5 350268-06 Assembly Instructions

Step 1.4 Bo Hg Screw the threaded rods Hg into the bushings Ne in ø3 x 12mm Screw x 4 M6 x 70mm Threaded rod x 4 the posts 1 and 2 . Vn

Fix the angles Vn to the Angle 23 x 23 x 24mm x 4 posts 1 and 2 using screws Bo into the holes indicated. Bo

Bo Vn

1 Hg

Bo Vn

350268-07 6 Assembly Instructions

Step 1.5 Fm Na

Place the side rails 5 onto the headboard ø35mm Bracket x 2 M6 x 10mm Nut x 2 posts 1 . Yb

Push the brackets Fm and 10/13mm Wrench x 1 the nuts Na into the holes indicated on the side rails 5 and onto the threaded rods Hg .

Tighten the nuts Na using the wrench Fm .

1 Hg

Fm Na

Na 5

Produced by: 5 NJA Furniture A/S DK-7700 Thisted Safety requirements: EN BS 8509:2008+A1:2011 Prod. wk/year: xx/201x

7 350268-08 Assembly Instructions

Step 1.6 Ec Fm Place the footboard posts 2 onto the side rails 5 . ø35mm Cap x 4 ø35mm Bracket x 2 Na Yb Push the brackets Fm and the nuts Na into the holes M6 x 10mm Nut x 2 10/13mm Wrench x 1 indicated on the side rails 5 and onto the threaded rods Hg .

Tighten the nuts Na using the wrench Fm . 2

Fm Na

Insert the caps Ec into the holes indicated on 5 Fm the side rails 5 . Na

350268-09 8 Assembly Instructions

Step 1.7 Hw Nf

Fix the top rails (side) 14 to the toprails (end) 15 using M6 x 80mm Bolt x 4 M6, ø10 x 12.5mm barrel nut x 4 bolts Hw into the barrel Ya nuts Nf . 4mm Allen key x 1 Use the allen key Ya . Nf Hw 15 Nf

Hw 14

Hw 14 Nf 15

Step 1.8 Bo Vq

Fix the corner angles Vq ø3 x 12mm Screw x 16 70 x 70 x 16mm Corner angle x 4 to the upper side of the top frame using screws Bo .

Bo Bo

Bo Vq

Vq Note !

The holes for the barrel nuts in the end rail 15 must point upwards

9 350268-10 Assembly Instructions

Hw Nf Step 1.9 Bo Place the top frame on the M6 x 80mm Bolt x 4 M6, ø10 x 12.5mm barrel nut x 4 top of the posts. ø3 x 12mm Screw x 4 Ya Fix it using screws Bo through the angles Vn . 14 4mm Allen key x 1 15 Nf Hw 15 Vn Nf Bo

Hw 15

14 14

Nf 14

Hw 15 14 Nf 15

Bo Vq

ø3 x 12mm Screw x 16 70 x 70 x 16mm Corner angle x 4

Bo Bo

Bo Vq

9 350268-10 350268-11 10 Assembly Instructions

Step 1.10 Bv

Fix the first of the slats 7 to the slatholders using ø3,5 x 30mm Screw x 2 screws Bv .

The slats 7 must be distributed evenly in the 6 bedframe. To get the distance right use the spacer block 6 as shown. 7 See detail. Bv

Bv 7

Step 1.11 Bv Fix the second of the slats 7 to the slatholders using ø3,5 x 30mm Screw x 2 screws Bv .

To get the distance right use the spacer block 6 as 6 shown.

See detail. 7

Bv 7

11 350268-12 Assembly Instructions

Bv Step 1.12 Bv

Fix the rest of the slats 7 ø3,5 x 30mm Screw x 2 using screws Bv . ø3,5 x 30mm Screw x 24

To get the distance right use the spacer block 6 as 6 shown.

See detail.

7 Bv

Bv 7

ø3,5 x 30mm Screw x 2 Bv

7 Bv 6

Bv 6

Bv 7 7

11 350268-12 350268-13 12 Assembly Instructions Step 2 Assembly of the drawer. 9 12

13 11 8 13

Step 2.1 Aa Cb

Screw the bolts Cb into ø7.8 x 40mm Wooden dowel x 12 ø5 x 8, cc34mm Bolt x 6 the holes indicated on the drawer back 11 and the Aa drawer sides 9 and 10 . 13 Aa Aa Aa Knock the dowels into Cb the holes indicated on the drawer back 11 , the Cb 11 drawer sides 9 and 10 and the Cb Cb

Aa 9 10

drawer rails 13 using a smal hammer. Aa Aa

Step 2.2 Ke Ta

Fix the wheels Ta onto ø6.1 x 11.5mm Screw8 x ø35mm Wheel x 4 the drawer sides 9 and 10 using screws Ke .

See detail. Ke Ke 9 Ta Ta 10 Ke

Ke Ke

13 350268-14 Assembly Instructions

Step 2.3 Cb Cb Screw the bolts Cb into 9 12 the holes indicated on ø5 x 8, cc34mm Bolt x 6 the drawer front 8 . Cb

13 Cb 11 13 8 8 Cb

Aa Cb Step 2.4 Ca

ø7.8 x 40mm Wooden dowel x 12 ø5 x 8, cc34mm Bolt x 6 Push the drawer sides 9 ø15 x 10.5mm Cam x 6 and 10 and the drawer Aa rails 13 onto the drawer 10 back 11 . Aa Aa 13 Cb Place cams Ca into the 13 Ca holes indicated. Arrow 11 Cb pointing towards the front. Turn the cams Ca to the Ca Cb Cb right to fix the drawer 13 back. Aa 9 11 10 Ca

9 Aa Aa Ca

Ke Ta

ø6.1 x 11.5mm Screw8 x ø35mm Wheel x 4 Step 2.5 Slide the drawer bottom Ke Ke 12 into the drawer sides 9 and 10 . 9 Ta Ta 10 Ke 12 Ta

10 Ke Ke

Ta 9

13 350268-14 350268-15 14 Assembly Instructions

Step 2.6 Ca

Push the drawer front 8 onto the drawer sides 9 ø15 x 10.5mm Cam x 6 and 10 and the drawer rails 13 .

Place cams Ca into the holes indicated. Arrow Ca pointing towards the front. Turn the cams Ca to the 8 right to fix the front. 10 Ca

Ca 13

Step 2.7 Place the drawer.

15 350268-16