Hardware List 1
Total Page:16
File Type:pdf, Size:1020Kb
V1731K-HF ANDERKIT BED ASSEMBLY INSTRUCTIONS 2 Poster Bed 4 Poster Bed Canopy Bed 1. SIDE RAIL AND FOOTBOARD ATTACHMENT HARDWARE LIST 1. Insert 4” threaded rods into the top and bottom holes located on the inside face of the headboard and footboard. A MACHINE BOLT 8 PCS. W2A42L.IG BTTFNCM� KOTUSVDUKPOT 2. Align the threaded rods and wood alignment dowels TKEF SBKM BOE GPPUCPBSE BUUBDINFOU with their corresponding holes on the end of the NUT 8 PCS. B side rail assembly and face of headboard and 21 KOTFSU 7" UISFBEFE SPET KOUP UIF UPR footboard.- CPUUPN Push IPMFT MPDBUFEside rail PO UIFassembly KOTKEF against GBDF PG UIF IFBECPBSE - GPPUCPBSE1 WASHER 8 PCS. headboard31 BMKHO UIF and UISFBEFE footboard SPET - YPPE and tighten in C BMKHONFOU EPYFMT YKUI UIFKS placeDPSSFTRPOEKOH using nuts IPMFT and PO specialty UIF FOE PG washer. UIF TKEF SBKM BTT� - GBDF PG IFBE. CPBSE BOE GPPUCPBSE1 RVTI TKEF SBKM SCREW 6 PCS. BTT� BHBKOTU IFBECPBSE BOE D GPPUCPBSE BOE UKHIUFO KO RMBDF VTKOH OVUT - TRFDKBMU� YBTIFS1 E SLAT LEG 3 PCS. A F METAL CANOPY 1 PC. 21 IFBECPBSE BTTFNCM� FINIAL G (USE 2 ON HDBD FOR 2 POSTER BED 4 PCS. OR USE 4 FOR A 4 POSTER BED) FOOTBOARD FINIAL 2 PCS. TKEF SBKM BTTFNCM� C H (USE ON FTBD FOR 2 POSTER BED) B FTBD FINIAL FILLER 2 PCS. 31 I (USE ON FTBD FOR 2 POSTER BED) GPPUCPBSE BTTFNCM� 2. SLAT INSTALLATION 3. OPTION A - CANOPY BED 1. Screw leg into the center hole of the slat rail. 1. Assemble canopy. 1 2. Use the 1 /2” wood screws to fasten 2. Remove the metal piece in top of each post sleeve. TMBU the LOTUBMMBULPO three slat assemblies to the 3. Take out the set screw and remove metal tube inside. top side of the slat bearing rails NOTE: Keep the metal tubes for future use for finials. 21 TDSFY located MFH LOUP on UIF the DFOUFS inside IPMF facePG of the UIF TMBU SBLM side2 rail assembly. One in the 4. Insert canopy ends into metal sleeves on top of each post. A1 WTF 2 A" YPPE TDSFYT UP GBTUFO UIF OPTION A - CANOPY BED UISFF center TMBU BTTFNCMLFT and the UPother UIF UPR two near TLEF PG UIF TMBU CFBSLOH SBLMT TMBU BTTFNCM� 5. Insert and tighten set screws on MPDBUFE the POends. UIF LOTLEF GBDF PG UIF 1. ASSEMBLE CANOPY AND INSERT ENDS TLEF SBLM BTT�1 POF LO UIF DFOUFS each post.INTO METAL SLEEVES ON TOP OF EACH BOE UIF PUIFS UYP OFBS UIF FOET POST. 2. TIGHTEN SET SCREWS ON EACH POST. 6. Tighten3. TIGHTENcenter CENTER finial FINIAL on ON canopy. CANOPY E TMBU ASSEMBLY. F MFH D A1 E 4. OPTION B - FOUR POSTER BED 5. OPTION C - TWO POSTER BED 1. Insert round finials into metal sleeves on top of each post. 1. Insert 3” diameter footboard finial through wood collar into top of footboard post. 2. Tighten set screws. PRUKPO2. Turn finial D. clockwiseU�P RPTUFS until tight. CFE OPTION B - FOUR POSTER BED 31 KOTFSU 5" EKBNFUFS GPPUCPBSE GKOKBM THROUGH WOOD COLLAR INTO TOP OF FOOTBOARD POST. TURN FINIAL CLOCKWISE UNTIL TIGHT. H G TNBMM GKOKBM H MBSHF GKOKBM I 1. INSERT ROUND FINIALS INTO METAL SLEEVES ON TOP OF EACH POST. 2. TIGHTEN SET SCREWS..