Assembly Instructions for 5Ft Classic Wall Arch Product Code: 30175

Assembly Instructions for 5ft Classic Wall Arch Product code: 30175

Please read these instructions carefully they are designed to make assembly quick and easy. Please check you have received the following components and refer to the attached diagrams.

Tools Required

Rubber mallet (or similar) Drill Tape measure Spirit level Phillips screwdriver Club hammer (or similar)

Agriframes, Journal house, Hartcliffe Way, Bristol, BS3 5RJ Order line: 0845 260 44 50 Fax: 0117 934 17 91 Order on-line: www.agriframes.co.uk

Parts List

Code Quantity Component A90016 1 Assembly kit (see check list) A24013 2 Monet curve (plain ends) A24014 2 Monet curve (reduced one end) A20014 4 42” uprights A11002 6 16¾” spacer bars A22011 1 Hole maker

Quantity Optional Component 3 Lattice panels 4 cells high x 3 cells wide 18 Lattice ties

Assembly Instructions

1. Preparation

1.1. Take four of the 42” uprights and tap an end plug into the standard end of each. 1.2. Place a screw in each T joint but only tighten the screws enough to hold them in. Make sure the screw points do not protrude into the inside of the joints as they will scratch the coating when they are attached to the tubes. 1.3. Take the six 16¾” spacers. Push T joints onto both ends of all of them. Lay each assembly flat to ensure the joints are parallel as shown below then measure the exposed tube and ensure that it is 13 ” long. If the measurement is greater than this you will need to

13 ”

use a rubber mallet to knock the joints home.

2. Assembling the roof section

2.1. Take the two Monet curves with plain ends, the two Monet curves with one reduced end and two of the 16¾” spacer bar assemblies. Refer to the diagram. Slide a spacer onto the horizontal section of the two Monet curves with a reduced end, connecting them together so that they are parallel. Repeat for the plain ended curves. 2.2. Refer to the diagram below. Take two moisture seals and two of the 16¾” spacers. Slide a moisture seal onto the two reduced tube ends and connect the two roof halves together. Ensure that the joins are covered by the moisture seals. Temporarily slide a spacer assembly onto each side of the roof section.

Do not attach these spacers. 2.3. Measure the diagonals of the roof section to ensure it is square and adjust if necessary.

3. Site preparation

3.1. Place the roof structure in the site that you intend to install the arch and mark the positions of the four uprights. Remove the roof section and use the Hole maker provided to make 13” deep holes at the four marks. Ensure that the holes are all vertical and the same depth. 3.2. Remove the two temporary lower spacers from the roof assembly. 3.3. Place one of the uprights with an end plug in each hole and ensure that the tops are level. Adjust if necessary.

4. Final assembly

4.1. Take the two uprights with end plugs fitted and place upright in each hole, end plug down. Check that the tops of the uprights are level. 4.2. Attach the bottom spacer bar between the uprights. 4.3. Slide a moisture seal onto the top of each upright and fit next 60” upright, cover the joint with the moisture seal. 4.4. Attach the middle & top spacer bars between the uprights. (This extended height Wall Arch will require the use of steps and probably assistance from another person when fitted and securing the roof section)

4.5. Slide the remaining two moisture seals onto the uprights. 4.6. Lift the roof section onto the uprights. Ensure that the moisture seals cover the tube joins. 4.7. Take the two 6.5” tubes from the wall fixing kit and connect them into the roof. Mark the positions of the fixing screws on the wall. Remove the two 6.5” tubes and drill the holes. Place a rawl plug in each hole. 4.8. Slide a moisture seal onto the reduced ends of the 6.5” tubes and tap an end plug into the bottom of each. Connect them to the roof again ensuring that the holes are aligned with the drilled holes in the wall. Slide the moisture seals up to cover the joins and then attach the arch to the wall using the screws and washers provided. Note that the washers fit between the 6.5” tubes and the wall. 4.9. Now make fully tighten the screws in all the T- joints. 4.10. If you purchased the lattice infill, refer to the diagram and attach it using the ties provided.

PACKING REFERENCE:

AGRIFRAMES KIT COMPONENT PACKING CHECK LIST

Code/Product Number 30175 Description 5ft Wall Arch

Kit Component Details Kit Number as referred to in main instructions A90016

Code Description DRAWINGS Quantity

3/4”x5/8" New Style T-Joint AGR-A610/13 Black 12 Checked

AGR-A610/40 3/4” Moisture Seal Black 8 Checked

AGR-A610/05 3/4" End Plug Black 4 Checked

No 10x1/2" Pozi Pan S/Tapp AGR-A73/009 AB Screw BZP 12 Checked

No.10x 13/4”” Slotted Round W/Screw Brass AGR-A73/012 4 Checked

AGR-A70/011 No.10 Rawl Plug 4 Checked

AGR-A610/43 3/4" Saddle Washers 4 Checked

6.5" Length(s) of Black Tube Punched+Swaged One AGR-A40/014 End 2 Checked

Authorised Packing Stamp:

PACKING REFERENCE:

Customer Note: In the unlikely event that there is any of the above components missing or are faulty please contact our Customer Helpline Number on 0845 260 44 50 and where possible quote the component code number to help us deal with your query promptly.