® Privacy Wall Slider

3/16" HEX BIT

#2 ACR BIT

Four Transom-Aligned Lites Three Equal Divided Lites

5/64 HEX

O YB RA

5/32 DRILL BIT

1" OPEN END Full Glass Four Equal Divided Lites Two Transom-Aligned Lites WRENCH

If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: 1.616.247.2500) LOCTITE 425® PLUMB BOB Or visit our website: www.steelcase.com © 2008 Steelcase Inc. Grand Rapids, MI 49501 U.S.A. Page 1 of 18 Printed in U.S.A. 939500487 Rev D ® HANGER KIT ASSY WITH CLAMP CHANNEL & BACK-TO-BACK SCREWS INCLUDED IN #10-16 x 1-1/2" PH TAP SCREWS SLIDING DOOR COVER HARDWARE BAG

Components

SLIDING DOOR (1) NON-LOCKING & (1) LOCKING DOOR STOP CHANNEL ASSY

SLIDING DOOR FRAME CHANNEL

SLIDING DOOR TRACK, LOCK KIT CONSISTING OF: SLIDER TRACK FASCIA ASSY, SLIDING DOOR HANDLE ASSY, BUMPER STOP ASSY'S, ADAMS RITE LOCK, #10-16 x 3/4" SELF DRILL PH SCREWS, KEY MORTISE 1/4-20 x 1/2" HEX HD TAP SCREWS CYLINDER & & 1/4-20 NUTS 1-1/8" THUMB TURN LEVER

DOUBLE STRIKE SLIDER PLINTH & #8-18 x 1/2" UNDERCUT FLAT HEAD TAP SCREWS

SLIDING DOOR CHANNEL, SINGLE STRIKE SLIDER PLINTH TRIMS, FINISHED END CAP ASSY & SLIDER STRIKE PLINTH TRIM & #10-16 x 1-1/2" PH TAP SCREWS #8-18 x 1/2" UNDERCUT FLAT HEAD TAP SCREWS

SLIDING DOOR GUIDE ASSY & #8-32 x 1/4" PAN HD TAP SCREWS

Page 2 of 18 939500487 Rev D ®

1. Install the fixed panel up into the track. 2d 2. Build the finished frame using a clamp channel and four (4) #10-16 x 1-1/2" pan head tapping screws. 2e

SLIDER DOOR SLIDING DOOR CHANNEL FRAME CHANNEL

2a

2c 2b #10-16 x 1-1/2" PAN HEAD TAPPING SCREW CLAMP CHANNEL

Page 3 of 18 939500487 Rev D ®

3. Install the finished frame into the opening between the fixed frame and the Pathways Privacy Wall.

3

Page 4 of 18 939500487 Rev D ®

4. Level the panels and 4c finished frame checking.

4a 4e

4b 4f

4d

Page 5 of 18 939500487 Rev D ®

5. Checking for plumb and squareness.

5b

5a

5c

Page 6 of 18 939500487 Rev D ®

6.Install the feature strips and lock the frame to the fixed panel and the Pathways Privacy Wall. FEATURE STRIP

6c 6a

6b

NOTE: Optional application for noise sensitive areas. Page 7 of 18 939500487 Rev D ®

NOTCHES

7.Install the sliding door track (7a). The sliding door track has two notches (7b) this is so the track is non-handed. Place the track in the top horizontals and lock into 7b place with four (4) #10-16 x 3/4" self drilling pan head screws.

SLIDING DOOR TRACK

7a

7c

#10-16 x 3/4" SELF DRILLING PAN HEAD SCREW

Page 8 of 18 939500487 Rev D ®

8.Install slider door guide assembly components together per the correct handing (8a). Install the slider door guide assembly onto the door stop channel assembly next to the fixed panel on the door side of the frame (8b). Support the slider door guide assembly temporarily with foam (8c). Install with (2) two #8-32 x 1/4" pan head tapping screws (8d). 8c

FOAM

DOOR STOP CHANNEL ASSEMBLY 8d

8a SLIDER DOOR 8b GUIDE ASSEMBLY

#8-32 x 1/4" PAN HEAD TAPPING SCREW Page 9 of 18 939500487 Rev D ®

HANGER KIT ASSEMBLY (BRACKET)

9b

9.Install the bumper stop assemblies loosely and the hanger kit assemblies (wheel portion) into the sliding door track (9a). Mount the hanger kit assembly (bracket) on top of the sliding door (9b) with screws that are provided with the hanger kit.

BUMPER STOP ASSEMBLY SCREW HANGER KIT ASSEMBLY (WHEEL) 9a

Page 10 of 18 939500487 Rev D ®

BUMPER STOP ASSEMBLY 10. Position the bottom of the sliding door on the guide 10c assembly (10a) and tilt the top up. Next, engage the sliding 10b door onto the hanger kit then lock the hanger kit in place (10b). Now adjust the hanger kit up or down to align sliding door, frame and panels. Adjust the bumper stop assemblies (10c).

10a

GUIDE ASSEMBLY

Page 11 of 18 939500487 Rev D ®

11a 11c FASCIA 11. There are two sets of holes on the door track. Place the fascia on top of the door track to see which holes are used for your installation.

Install the 1/4-20 x 1/2" hex head tapping screws up from bottom side and add the 1/4-20 nuts to the top side of the door track (11a) loosely, leaving 11b to slide the fascia between the track and the nuts. Position the fascia (11b) and tighten the nuts (11c).

Page 12 of 18 939500487 Rev D ®

SET SCREW

12c

12. Install collar, lock washer and screw onto the handle that has threads inside the tubes as shown (12a). Place the handle with the 12b clearance hole inside the tubes over 12a the screw head and collar (12b). Install the set screws on the upper and lower portion of the handle using Loctite 425 (12c). NOTE: Make sure the set screws are located on the bottom of the handle, so they are not visible to the user. Insert the lock body into the sliding door frame and start screws to hole lock loosely. Install key and thumb HANDLE cylinder. Lock cylinders in place with COLLAR 3/32" ALLEN (WITH CLEARANCE SCREW WRENCH set screws then tighten lock body HOLE INSIDE TUBES) screws check lock, key and thumb HANDLE (WITH THREADS LOCK WASHER and adjust after complete. Place the INSIDE TUBES) trim around lock bodies (12d).

FOR FIELD INSTALLED HANDLE OPTION

Locate handle mounting 12d holes in this zone. 5/8" DOOR VERTICAL 5/8"

Page 13 of 18 939500487 Rev D ®

PATHWAYS PRIVACY WALL NOTE: This view is shown turned 90 degrees for clarity. PATHWAYS PRIVACY WALL SLIDING DOOR FRAME

13. Mount the single strike slider plinth trim with a #8-18 x 1/2" undercut flat head tap screw as shown, making sure the base trim mounts with clean lines. 14. Mount the single strike slider plinth trim and the slider strike plinth trim with two (2) #8-18 x 1/2" undercut flat head tap screw as shown, making sure all the trims mount with clean lines. 14

NOTE: This view is shown SINGLE STRIKE turned 90 degrees for clarity. SLIDER PLINTH TRIM PATHWAYS PRIVACY WALL SLIDING DOOR SLIDER STRIKE PLINTH TRIM

SINGLE STRIKE SLIDER PLINTH TRIM 13

Page 14 of 18 939500487 Rev D ®

BACK-TO-BACK PATHWAYS PRIVACY WALL SLIDING DOOR FRAMES

NOTE: This view is shown turned 90 degrees for clarity. 15. Use an awl and scribe down inside the step of the plinth trim (15a & 15c) and then take a pair of pliers and snap the thin metal step off the trim (15b & 15d). 16. Mount the two (2) single strike slider plinth trims with two (2) #8-18 x 1/2" undercut flat head tap screws as shown. 17. Mount the two (2) slider strike plinth trims with two (2) #8-18 x 1/2" undercut flat head tap screws as shown.

15a 15b

SLIDER STRIKE PLINTH TRIM

16

15c 15d SINGLE STRIKE SLIDER PLINTH TRIMS 17 SLIDER STRIKE PLINTH TRIMS SINGLE STRIKE SLIDER PLINTH TRIM

Page 15 of 18 939500487 Rev D ®

BACK-TO-BACK NOTE: This view is shown PATHWAYS PRIVACY WALL SLIDING DOOR FRAMES turned 90 degrees for clarity.

Optional Back-to-Back Cover (Inline Application) 1. Use an awl and scribe down inside the step of the 2b single strike slider plinth trim (15c on previous page) and then take a pair of pliers and snap the thin metal step off the trim (15d on previous page). Two (2) single slider plinth trims are required for this installation. 2. Slide the double strike sliding door plinth trim over the back-to-back pathways privacy wall sliding door frames and secure with two (2) #8-18 x 1/2" undercut flat head tap screws (2a). Slide the back-to-back slider cover over the frames and on top of the plinth trim and snap into position (2b). 3. Install the two (2) single strike slider plinth trims with #8-18 x 1/2" undercut flat head tap screws as shown.

3

BACK-TO-BACK SLIDER COVER

2a SINGLE STRIKE DOUBLE STRIKE SLIDING SLIDER PLINTH TRIMS DOOR PLINTH TRIM

Page 16 of 18 939500487 Rev D ®

= Inline Feature Strip

= Half Feature Strip 1.341" ~ CL (1-11/32")

Optional Connection Conditions

NOTE: All other connection conditions C are the same as standard panel L mounting connection conditions.

1.341" ~ CL (1-11/32")

Sliding Door

CL

90o with Centered Panel with a Sliding Door

Sliding Door Sliding Door

"T" with Two (2) Sliding Centered

Page 17 of 18 939500487 Rev D ® BASE TRIM Factory edge CORNER of base trim CL BASE TRIM Step removed on plinth

Optional Plinth and Base Trim Connection Conditions Sliding Door BASE TRIM

NOTE: All other plinth and base trim connection conditions are the same as standard panel mounting plinth and base trim connection conditions. SLIDER STRIKE PLINTH

"T" with a Sliding Door Centered BASE TRIM BASE TRIM Factory edge Factory edge BASE TRIM of base trim CL of base trim Factory edge BASE TRIM Step removed Step removed of base trim C L on plinth on plinth Step removed on plinth

SINGLE STRIKE SLIDER PLINTH

Sliding Door Sliding Door

Sliding Door Steps removed on both plinths

SLIDER STRIKE PLINTH SLIDER STRIKE SLIDER STRIKE PLINTH PLINTH 90o with Centered Panel Steps removed with a Sliding Door on both plinths "T" with Two (2) Sliding Doors Centered Page 18 of 18 939500487 Rev D