Introduction to Advanced Semiconductor Memories

Total Page:16

File Type:pdf, Size:1020Kb

Introduction to Advanced Semiconductor Memories CHAPTER 1 INTRODUCTION TO ADVANCED SEMICONDUCTOR MEMORIES 1.1. SEMICONDUCTOR MEMORIES OVERVIEW The goal of Advanced Semiconductor Memories is to complement the material already covered in Semiconductor Memories. The earlier book covered the fol- lowing topics: random access memory technologies (SRAMs and DRAMs) and their application to specific architectures; nonvolatile technologies such as the read-only memories (ROMs), programmable read-only memories (PROMs), and erasable PROMs in both ultraviolet erasable (UVPROM) and electrically erasable (EEPROM) versions; memory fault modeling and testing; memory design for testability and fault tolerance; semiconductor memory reliability; semiconductor memories radiation effects; advanced memory technologies; and high-density memory packaging technologies [1]. This section provides a general overview of the semiconductor memories topics that are covered in Semiconductor Memories. In the last three decades of semiconductor memories' phenomenal growth, the DRAMs have been the largest volume volatile memory produced for use as main computer memories because of their high density and low cost per bit advantage. SRAM densities have generally lagged a generation behind the DRAM. However, the SRAMs offer low-power consumption and high-per- formance features, which makes them practical alternatives to the DRAMs. Nowadays, a vast majority of SRAMs are being fabricated in the NMOS and CMOS technologies (and a combination of two technologies, also referred to as the mixed-MOS) for commodity SRAMs. 1 2 INTRODUCTION TO ADVANCED SEMICONDUCTOR MEMORIES MOS Memory Market ($M) Non-Memory IC Market ($M) Memory % of Total IC Market 300,000 40% 250,000 30% 200,00U "o Q 15 150,000 20% 2 </> a. o 100,000 2 10% 50,000 0 0% 96 97 98 99 00 01* 02* 03* 04* 05* MOS Memory Market ($M) 36,019 29,335 22,994 32,288 49,112 51,646 56,541 70,958 94,541 132,007 Non-Memory IC Market ($M) 78,923 90,198 86,078 97,930 126,551 135,969 148,512 172,396 207,430 262,172 Memory % of Total IC Market 31% . 25% 21% 25% 28% 28% 28% 29% 31% 33% Year Figure 1.1 Semiconductor memory market as a percentage of the total IC market [2]. In 1995, semiconductor memories accounted for 42% of the total IC market, but following 1995's strong growth, memory prices collapsed for the next three years. In 1998, memory devices represented only 21% of the total IC market. During the 1990s, semiconductor memory sales averaged approximately 30% of total IC sales. It is forecasted that the memory portion of total IC sales will gradually increase through year 2005. Figure 1.1 shows the semiconductor memory market as a percentage of the total IC market [2]. In high-density and high-speed applications, various combinations of bipo- lar and MOS technologies are being used. In addition to MOS and bipolar memories, referred to as the "bulk silicon" technologies, silicon-on-insulator (SOI) isolation technologies have been developed for improved radiation hardness. SRAM density and performance are usually enhanced by scaling down the device geometries. Advanced SRAM designs and architectures for 4 to 16-Mb chips with submicron feature sizes have been developed and currently available as commodity chips. Application-specific memory designs include first-in-first- out (FIFO) buffer memory, in which the data are transferred in and out serially. The dual-port RAMs allow two independent devices to have simulta- neous read and write access to the same memory. The content addressable memories (CAMs) are designed and used both as the embedded modules on SEMICONDUCTOR MEMORIES OVERVIEW 3 larger VLSI chips, and as stand-alone memory for specific system applications. A major improvement in DRAM evolution has been the switch from three-transistor (3T) designs to one-transistor (IT) cell design, enabling pro- duction of 4- to 16-Mb density chips that use advanced 3-D trench capacitor and stacked capacitor cell structure. Currently, 64-Mb to 1-Gb DRAM chips are in production, and multigigabit density chips are being developed. The technical advances in multimegabit DRAMs have resulted in greater demand for application-specific products such as the pseudostatic DRAM (PSRAM), which uses dynamic storage cells but contains all refresh logic on-chip that enables it to function similarly to an SRAM. Video DRAMs (VDRAMs) have been produced for use as the multiport graphic buffers. Some other examples of high-speed DRAM innovative architectures are synchronous DRAMs (SDRAMs), cache DRAMs (CDRAMs), and Rambus™ DRAMs (RDRAMs). Nonvolatile memories (NVMs) have also experienced tremendous growth since the introduction in 1970 of a floating polysilicon gate-based erasable program read-only memory (EPROM), in which hot electrons are injected into the floating gate and removed either by ultraviolet internal photoemission or by Fowler-Nordheim tunneling. The EPROMs (also referred to as the UVEPROMs) are erased by removing them from the target system and exposing them to ultraviolet light. An alternative to EPROM (or UVEPROM) has been the development of electrically erasable PROMs (EEPROMs), which offer in-circuit programming flexibility. Several variations of this technology include metal-nitride-oxide-semiconductor (MNOS), silicon-oxide-nitride- oxide-semiconductor (SONOS), floating gate tunneling oxide (FLOTOX), and textured polysilicon. The FLOTOX is most commonly used EEPROM technology. An interesting NVM architecture is the nonvolatile SRAM, a combination of EEPROM and SRAM in which each SRAM has a correspond- ing "shadow" EEPROM cell. Flash memories based on EPROM or EEPROM technologies are devices for which contents of all memory array cells can be erased simultaneously, unlike the EEPROMs that have select transistors incorporated in each cell to allow for the individual byte erasure. Therefore, the flash memories can be made roughly two or three times smaller than the floating gate EEPROM cells. Flash memories are available in 8- to 512-Mb densities as production devices, and even higher densities in development. DRAMs are currently (and predicted to be in the future) the largest memory segment in terms of dollar sales. After DRAMs the SRAMs and flash markets represent the next two largest memory segments. In year 2000, the flash memory market surpassed the SRAM market and became the second-largest memory market segment. Both DRAM and flash market shares are expected to continue growing through 2005, although flash memory at a much faster pace. The remaining memory segments are predicted to remain stable. 4 INTRODUCTION TO ADVANCED SEMICONDUCTOR MEMORIES Figure 1.2a shows a comparison of different MOS technologies market share projected to year 2005 [2]. It is predicted that in year 2005, the DRAMs will account for just 60% of the memory market, whereas flash memory sales is forecast to account for 29% of the total memory market. Figure 2.2b shows percentages for each MOS memory technology market for the year 2000 and predicted values for the year 2005. Semiconductor Memories reviewed various memory failure modes and mech- anisms, fault modeling, and electrical testing [1]. A most commonly used fault model is the single-stuck-at fault (SSF), which is also referred to as the classical standard fault model. However, many other fault models have also been developed for transition faults (TFs), address faults (AFs), bridging faults (BFs), coupling faults (CFs), pattern-sensitive faults (PSFs), and the dynamic (or delay) faults. A large percentage of physical faults occurring in the ICs can be considered as the bridging faults (BFs), consisting of shorts between the two or more cells or lines. Another important category of faults that can cause the RAM cell to function erroneously is the coupling or PSFs. In general, the memory electrical testing consists of the dc and ac parametric tests and functional tests. For RAMs, various functional test algorithms have been developed for which the test time is a function of the number of memory bits (n) and range in complexity from O(n) to O(n2). The selection of a particular set of test patterns for a given RAM is influenced by the type of failure modes to be detected, memory bit density that influences the test time, and the memory automated test equipment (ATE) availability. Advanced megabit memory architectures are being designed with special test features to reduce the test time by the use of multibit test (MBT), line mode test (LMT), and built-in self-test (BIST). Application-specific memories such as the FIFOs, video RAMs, synchronous static and dynamic RAMs, and double- buffered memories (DBMs) have complex timing requirements and multiple setup modes that require a suitable mix of sophisticated test hardware, design for testability (DFT), and BIST approach. In general, the memory testability is a function of variables such as circuit complexity and design methodology. Therefore, the DFT techniques, RAM and ROM BIST architectures, memory error detection and correction (EDAC), and the memory fault tolerance are important design considerations. Structured design techniques are based upon the concept of providing uniform design to increase controllability and observability. The commonly used methodologies include the level-sensitive scan design (LSSD), scan path, scan/set logic, random access scan, and the boundary scan testing (BST). The RAM BIST implementation strategies include the use of algorithmic test sequence (ATS), the 13-N March algorithms with a data-retention test, a fault-syndrome-based strategy for detecting the PSFs, and
Recommended publications
  • Chapter 3 Semiconductor Memories
    Chapter 3 Semiconductor Memories Jin-Fu Li Department of Electrical Engineering National Central University Jungli, Taiwan Outline Introduction Random Access Memories Content Addressable Memories Read Only Memories Flash Memories Advanced Reliable Systems (ARES) Lab. Jin-Fu Li, EE, NCU 2 Overview of Memory Types Semiconductor Memories Read/Write Memory or Random Access Memory (RAM) Read Only Memory (ROM) Random Access Non-Random Access Memory (RAM) Memory (RAM) •Mask (Fuse) ROM •Programmable ROM (PROM) •Erasable PROM (EPROM) •Static RAM (SRAM) •FIFO/LIFO •Electrically EPROM (EEPROM) •Dynamic RAM (DRAM) •Shift Register •Flash Memory •Register File •Content Addressable •Ferroelectric RAM (FRAM) Memory (CAM) •Magnetic RAM (MRAM) Advanced Reliable Systems (ARES) Lab. Jin-Fu Li, EE, NCU 3 Memory Elements – Memory Architecture Memory elements may be divided into the following categories Random access memory Serial access memory Content addressable memory Memory architecture 2m+k bits row decoder row decoder 2n-k words row decoder row decoder column decoder k column mux, n-bit address sense amp, 2m-bit data I/Os write buffers Advanced Reliable Systems (ARES) Lab. Jin-Fu Li, EE, NCU 4 1-D Memory Architecture S0 S0 Word0 Word0 S1 S1 Word1 Word1 S2 S2 Word2 Word2 A0 S3 S3 A1 Decoder Ak-1 Sn-2 Storage Sn-2 Wordn-2 element Wordn-2 Sn-1 Sn-1 Wordn-1 Wordn-1 m-bit m-bit Input/Output Input/Output n select signals are reduced n select signals: S0-Sn-1 to k address signals: A0-Ak-1 Advanced Reliable Systems (ARES) Lab. Jin-Fu Li, EE, NCU 5 Memory Architecture S0 Word0 Wordi-1 S1 A0 A1 Ak-1 Row Decoder Sn-1 Wordni-1 A 0 Column Decoder Aj-1 Sense Amplifier Read/Write Circuit m-bit Input/Output Advanced Reliable Systems (ARES) Lab.
    [Show full text]
  • Memory & Devices
    Memory & Devices Memory • Random Access Memory (vs. Serial Access Memory) • Different flavors at different levels – Physical Makeup (CMOS, DRAM) – Low Level Architectures (FPM,EDO,BEDO,SDRAM, DDR) • Cache uses SRAM: Static Random Access Memory – No refresh (6 transistors/bit vs. 1 transistor • Main Memory is DRAM: Dynamic Random Access Memory – Dynamic since needs to be refreshed periodically (1% time) – Addresses divided into 2 halves (Memory as a 2D matrix): • RAS or Row Access Strobe • CAS or Column Access Strobe Random-Access Memory (RAM) Key features – RAM is packaged as a chip. – Basic storage unit is a cell (one bit per cell). – Multiple RAM chips form a memory. Static RAM (SRAM) – Each cell stores bit with a six-transistor circuit. – Retains value indefinitely, as long as it is kept powered. – Relatively insensitive to disturbances such as electrical noise. – Faster and more expensive than DRAM. Dynamic RAM (DRAM) – Each cell stores bit with a capacitor and transistor. – Value must be refreshed every 10-100 ms. – Sensitive to disturbances. – Slower and cheaper than SRAM. Semiconductor Memory Types Static RAM • Bits stored in transistor “latches” à no capacitors! – no charge leak, no refresh needed • Pro: no refresh circuits, faster • Con: more complex construction, larger per bit more expensive transistors “switch” faster than capacitors charge ! • Cache Static RAM Structure 1 “NOT ” 1 0 six transistors per bit 1 0 (“flip flop”) 0 1 0/1 = example 0 Static RAM Operation • Transistor arrangement (flip flop) has 2 stable logic states • Write 1. signal bit line: High à 1 Low à 0 2. address line active à “switch” flip flop to stable state matching bit line • Read no need 1.
    [Show full text]
  • Section 10 Flash Technology
    10 FLASH TECHNOLOGY Overview Flash memory technology is a mix of EPROM and EEPROM technologies. The term “flash” was chosen because a large chunk of memory could be erased at one time. The name, therefore, distinguishes flash devices from EEPROMs, where each byte is erased individually. Flash memory technology is today a mature technology. Flash memory is a strong com- petitor to other memories such as EPROMs, EEPROMs, and to some DRAM applications. Figure 10-1 shows the density comparison of a flash versus other memories. 64M 16M 4M DRAM/EPROM 1M SRAM/EEPROM Density 256K Flash 64K 1980 1982 1984 1986 1988 1990 1992 1994 1996 Year Source: Intel/ICE, "Memory 1996" 18613A Figure 10-1. Flash Density Versus Other Memory How the Device Works The elementary flash cell consists of one transistor with a floating gate, similar to an EPROM cell. However, technology and geometry differences between flash devices and EPROMs exist. In particular, the gate oxide between the silicon and the floating gate is thinner for flash technology. It is similar to the tunnel oxide of an EEPROM. Source and INTEGRATED CIRCUIT ENGINEERING CORPORATION 10-1 Flash Technology drain diffusions are also different. Figure 10-2 shows a comparison between a flash cell and an EPROM cell with the same technology complexity. Due to thinner gate oxide, the flash device will be more difficult to process. CMOS Flash Cell CMOS EPROM Cell Mag. 10,000x Mag. 10,000x Flash Memory Cell – Larger transistor – Thinner floating gate – Thinner oxide (100-200Å) Photos by ICE 17561A Figure 10-2.
    [Show full text]
  • Error Detection and Correction Methods for Memories Used in System-On-Chip Designs
    International Journal of Engineering and Advanced Technology (IJEAT) ISSN: 2249 – 8958, Volume-8, Issue-2S2, January 2019 Error Detection and Correction Methods for Memories used in System-on-Chip Designs Gunduru Swathi Lakshmi, Neelima K, C. Subhas ABSTRACT— Memory is the basic necessity in any SoC Static Random Access Memory (SRAM): It design. Memories are classified into single port memory and consists of a latch or flipflop to store each bit of multiport memory. Multiport memory has ability to source more memory and it does not required any refresh efficient execution of operation and high speed performance operation. SRAM is mostly used in cache memory when compared to single port. Testing of semiconductor memories is increasing because of high density of current in the and in hand-held devices. It has advantages like chips. Due to increase in embedded on chip memory and memory high speed and low power consumption. It has density, the number of faults grow exponentially. Error detection drawback like complex structure and expensive. works on concept of redundancy where extra bits are added for So, it is not used for high capacity applications. original data to detect the error bits. Error correction is done in Read Only Memory (ROM): It is a non-volatile memory. two forms: one is receiver itself corrects the data and other is It can only access data but cannot modify data. It is of low receiver sends the error bits to sender through feedback. Error detection and correction can be done in two ways. One is Single cost. Some applications of ROM are scanners, ID cards, Fax bit and other is multiple bit.
    [Show full text]
  • Nanotechnology ? Nram (Nano Random Access
    International Journal Of Engineering Research and Technology (IJERT) IFET-2014 Conference Proceedings INTERFACE ECE T14 INTRACT – INNOVATE - INSPIRE NANOTECHNOLOGY – NRAM (NANO RANDOM ACCESS MEMORY) RANJITHA. T, SANDHYA. R GOVERNMENT COLLEGE OF TECHNOLOGY, COIMBATORE 13. containing elements, nanotubes, are so small, NRAM technology will Abstract— NRAM (Nano Random Access Memory), is one of achieve very high memory densities: at least 10-100 times our current the important applications of nanotechnology. This paper has best. NRAM will operate electromechanically rather than just been prepared to cull out answers for the following crucial electrically, setting it apart from other memory technologies as a questions: nonvolatile form of memory, meaning data will be retained even What is NRAM? when the power is turned off. The creators of the technology claim it What is the need of it? has the advantages of all the best memory technologies with none of How can it be made possible? the disadvantages, setting it up to be the universal medium for What is the principle and technology involved in NRAM? memory in the future. What are the advantages and features of NRAM? The world is longing for all the things it can use within its TECHNOLOGY palm. As a result nanotechnology is taking its head in the world. Nantero's technology is based on a well-known effect in carbon Much of the electronic gadgets are reduced in size and increased nanotubes where crossed nanotubes on a flat surface can either be in efficiency by the nanotechnology. The memory storage devices touching or slightly separated in the vertical direction (normal to the are somewhat large in size due to the materials used for their substrate) due to Van der Waal's interactions.
    [Show full text]
  • DDR and DDR2 SDRAM Controller Compiler User Guide
    DDR and DDR2 SDRAM Controller Compiler User Guide 101 Innovation Drive Software Version: 9.0 San Jose, CA 95134 Document Date: March 2009 www.altera.com Copyright © 2009 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo, specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents and pending ap- plications, maskwork rights, and copyrights. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. UG-DDRSDRAM-10.0 Contents Chapter 1. About This Compiler Release Information . 1–1 Device Family Support . 1–1 Features . 1–2 General Description . 1–2 Performance and Resource Utilization . 1–4 Installation and Licensing . 1–5 OpenCore Plus Evaluation . 1–6 Chapter 2. Getting Started Design Flow . 2–1 SOPC Builder Design Flow . 2–1 DDR & DDR2 SDRAM Controller Walkthrough .
    [Show full text]
  • AXP Internal 2-Apr-20 1
    2-Apr-20 AXP Internal 1 2-Apr-20 AXP Internal 2 2-Apr-20 AXP Internal 3 2-Apr-20 AXP Internal 4 2-Apr-20 AXP Internal 5 2-Apr-20 AXP Internal 6 Class 6 Subject: Computer Science Title of the Book: IT Planet Petabyte Chapter 2: Computer Memory GENERAL INSTRUCTIONS: • Exercises to be written in the book. • Assignment questions to be done in ruled sheets. • You Tube link is for the explanation of Primary and Secondary Memory. YouTube Link: ➢ https://youtu.be/aOgvgHiazQA INTRODUCTION: ➢ Computer can store a large amount of data safely in their memory for future use. ➢ A computer’s memory is measured either in Bits or Bytes. ➢ The memory of a computer is divided into two categories: Primary Memory, Secondary Memory. ➢ There are two types of Primary Memory: ROM and RAM. ➢ Cache Memory is used to store program and instructions that are frequently used. EXPLANATION: Computer Memory: Memory plays a very important role in a computer. It is the basic unit where data and instructions are stored temporarily. Memory usually consists of one or more chips on the mother board, or you can say it consists of electronic components that store instructions waiting to be executed by the processor, data needed by those instructions, and the results of processing the data. Memory Units: Computer memory is measured in bits and bytes. A bit is the smallest unit of information that a computer can process and store. A group of 4 bits is known as nibble, and a group of 8 bits is called byte.
    [Show full text]
  • Low Voltage, One-Time Programmable, Read-Only Memory
    Features • Fast read access time – 90ns • Dual voltage range operation – Low voltage power supply range, 3.0V to 3.6V, or – Standard power supply range, 5V 10% • Compatible with JEDEC standard Atmel® AT27C512R • Low-power CMOS operation – 20µA max standby (less than 1µA, typical) for VCC = 3.6V – 29mW max active at 5MHz for VCC = 3.6V 512K (64K x 8) • JEDEC standard package – 32-lead PLCC Low Voltage, • High-reliability CMOS technology One-time – 2,000V ESD protection Programmable, – 200mA latchup immunity • Rapid programming algorithm – 100µs/byte (typical) Read-only Memory • CMOS- and TTL-compatible inputs and outputs – JEDEC standard for LVTTL • Integrated product identification code Atmel AT27LV512A • Industrial temperature range • Green (Pb/halide-free) packaging option 1. Description The Atmel AT27LV512A is a high-performance, low-power, low-voltage, 524,288-bit, one- time programmable, read-only memory (OTP EPROM) organized as 64K by 8 bits. It requires only one supply in the range of 3.0 to 3.6V in normal read mode operation, making it ideal for fast, portable systems using battery power. The Atmel innovative design techniques provide fast speeds that rival 5V parts, while keep- ing the low power consumption of a 3.3V supply. At VCC = 3.0V, any byte can be accessed in less than 90ns. With a typical power dissipation of only 18mW at 5MHz and VCC = 3.3V, the AT27LV512A consumes less than one-fifth the power of a standard, 5V EPROM. Standby mode supply current is typically less than 1µA at 3.3V. The AT27LV512A is available in industry-standard, JEDEC-approved, one-time programmable (OTP) PLCC package.
    [Show full text]
  • Lecture 27 Semiconductor Memory: DRAM and Non-Volatile Memory Administrivia
    Lecture 27 Semiconductor Memory: DRAM and Non-Volatile Memory Digital Integrated Circuits Interconnect © Prentice Hall 2000 Administrivia l Today: Project phase 3 announcement. l Poster Session Tu 5/8 1-4pm » Location BWRC, 2108 Allston Way l Last lecture on Th 5/3 will cover issues in IC design Digital Integrated Circuits Interconnect © Prentice Hall 2000 1 Lectures Last l ROM and SRAM Today l Introducing the project phase III l DRAM and Non-volatile Digital Integrated Circuits Interconnect © Prentice Hall 2000 Project Phase III A proposed SRAM cell! w/ Control Circuit Digital Integrated Circuits Interconnect © Prentice Hall 2000 2 Tasks l Explain the behavior of the cell in its global contents. Provide transient simulations to illustrate. l Identify weakness of the cell in terms of signal integrity and power dissipation. Quantify your statements. l Propose an implementation that improves power dissipation. Digital Integrated Circuits Interconnect © Prentice Hall 2000 Report l Report » Comparison, Selection, Electrical Design » Cell Layout, Timing Waveforms in SRAM, Simulation » Power and Estimation and Proposal for SRAM power reduction l 3 slides on poster, each of which represents one of the tasks of the previous slide » Explanation of cell operation, comparison, design » Cell Operation in SRAM, Waveforms, Simulation » Proposal of improved SRAM implementation (from a power perspective) Digital Integrated Circuits Interconnect © Prentice Hall 2000 3 SEMICONDUCTOR MEMORIES Digital Integrated Circuits Interconnect © Prentice Hall 2000 3-Transistor DRAM Cell BL1 BL2 WWL WWL RWL RWL X X M3 VDD-VT M2 M1 VDD BL1 CS BL2 VDD-VT DV No constraints on device ratios Reads are non-destructive Value stored at node X when writing a “1” = VWWL-VTn Digital Integrated Circuits Interconnect © Prentice Hall 2000 4 3T-DRAM — Layout BL2 BL1 GND RWL M3 M2 WWL M1 Digital Integrated Circuits Interconnect © Prentice Hall 2000 1-Transistor DRAM Cell BL WL Write "1" Read "1" WL 1 M C X S GND VDD-VT V BL DD VDD/2 VDD/2 CBL sensing Write: CS is charged or discharged by asserting WL and BL.
    [Show full text]
  • Nanotechnology Trends in Nonvolatile Memory Devices
    IBM Research Nanotechnology Trends in Nonvolatile Memory Devices Gian-Luca Bona [email protected] IBM Research, Almaden Research Center © 2008 IBM Corporation IBM Research The Elusive Universal Memory © 2008 IBM Corporation IBM Research Incumbent Semiconductor Memories SRAM Cost NOR FLASH DRAM NAND FLASH Attributes for universal memories: –Highest performance –Lowest active and standby power –Unlimited Read/Write endurance –Non-Volatility –Compatible to existing technologies –Continuously scalable –Lowest cost per bit Performance © 2008 IBM Corporation IBM Research Incumbent Semiconductor Memories SRAM Cost NOR FLASH DRAM NAND FLASH m+1 SLm SLm-1 WLn-1 WLn WLn+1 A new class of universal storage device : – a fast solid-state, nonvolatile RAM – enables compact, robust storage systems with solid state reliability and significantly improved cost- performance Performance © 2008 IBM Corporation IBM Research Non-volatile, universal semiconductor memory SL m+1 SL m SL m-1 WL n-1 WL n WL n+1 Everyone is looking for a dense (cheap) crosspoint memory. It is relatively easy to identify materials that show bistable hysteretic behavior (easily distinguishable, stable on/off states). IBM © 2006 IBM Corporation IBM Research The Memory Landscape © 2008 IBM Corporation IBM Research IBM Research Histogram of Memory Papers Papers presented at Symposium on VLSI Technology and IEDM; Ref.: G. Burr et al., IBM Journal of R&D, Vol.52, No.4/5, July 2008 © 2008 IBM Corporation IBM Research IBM Research Emerging Memory Technologies Memory technology remains an
    [Show full text]
  • Embedded DRAM
    Embedded DRAM Raviprasad Kuloor Semiconductor Research and Development Centre, Bangalore IBM Systems and Technology Group DRAM Topics Introduction to memory DRAM basics and bitcell array eDRAM operational details (case study) Noise concerns Wordline driver (WLDRV) and level translators (LT) Challenges in eDRAM Understanding Timing diagram – An example References Slide 1 Acknowledgement • John Barth, IBM SRDC for most of the slides content • Madabusi Govindarajan • Subramanian S. Iyer • Many Others Slide 2 Topics Introduction to memory DRAM basics and bitcell array eDRAM operational details (case study) Noise concerns Wordline driver (WLDRV) and level translators (LT) Challenges in eDRAM Understanding Timing diagram – An example Slide 3 Memory Classification revisited Slide 4 Motivation for a memory hierarchy – infinite memory Memory store Processor Infinitely fast Infinitely large Cycles per Instruction Number of processor clock cycles (CPI) = required per instruction CPI[ ∞ cache] Finite memory speed Memory store Processor Finite speed Infinite size CPI = CPI[∞ cache] + FCP Finite cache penalty Locality of reference – spatial and temporal Temporal If you access something now you’ll need it again soon e.g: Loops Spatial If you accessed something you’ll also need its neighbor e.g: Arrays Exploit this to divide memory into hierarchy Hit L2 L1 (Slow) Processor Miss (Fast) Hit Register Cache size impacts cycles-per-instruction Access rate reduces Slower memory is sufficient Cache size impacts cycles-per-instruction For a 5GHz
    [Show full text]
  • Solving High-Speed Memory Interface Challenges with Low-Cost Fpgas
    SOLVING HIGH-SPEED MEMORY INTERFACE CHALLENGES WITH LOW-COST FPGAS A Lattice Semiconductor White Paper May 2005 Lattice Semiconductor 5555 Northeast Moore Ct. Hillsboro, Oregon 97124 USA Telephone: (503) 268-8000 www.latticesemi.com Introduction Memory devices are ubiquitous in today’s communications systems. As system bandwidths continue to increase into the multi-gigabit range, memory technologies have been optimized for higher density and performance. In turn, memory interfaces for these new technologies pose stiff challenges for designers. Traditionally, memory controllers were embedded in processors or as ASIC macrocells in SoCs. With shorter time-to-market requirements, designers are turning to programmable logic devices such as FPGAs to manage memory interfaces. Until recently, only a few FPGAs supported the building blocks to interface reliably to high-speed, next generation devices, and typically these FPGAs were high-end, expensive devices. However, a new generation of low-cost FPGAs has emerged, providing the building blocks, high-speed FPGA fabric, clock management resources and the I/O structures needed to implement next generation DDR2, QDR2 and RLDRAM memory controllers. Memory Applications Memory devices are an integral part of a variety of systems. However, different applications have different memory requirements. For networking infrastructure applications, the memory devices required are typically high-density, high-performance, high-bandwidth memory devices with a high degree of reliability. In wireless applications, low-power memory is important, especially for handset and mobile devices, while high-performance is important for base-station applications. Broadband access applications typically require memory devices in which there is a fine balance between cost and performance.
    [Show full text]