TV Cabling Solutions Catalogue

When it comes to antenna installation, the choice is clear Choosing the Right Antenna

The new version of TV Across Australia will include the most up to date planning and implementation of all analogue and digital broadcast TV services throughout the country. It will also include an antenna selection for each transmitter making choosing the right antenna a very simple exercise. You cannot afford to be without this great reference guide. What frequencies are being broadcast in the location of the installation?

• Every TV transmitter Across Australia • Clipsal Antenna part number for every TV transmitter • Location maps for every TV transmitter Across Australia • Analogue and Digital TV channels broadcast from every TV transmitter

Part No: 3105TVA Contents

4 Terminology 6 MATV basics 10 Antennas 26 Mounting Accessories 38 Splitters 43 Diplexers 44 Drop Taps 46 Coaxial Cable 50 Coaxial Cable Connectors 54 Installation Tips 56 Installation Tools 59 MATV Adaptors 63 Fly Leads 65 TV Mechs 66 Wall Plates 69 Location Guides Terminology TERMINOLOGY Amplification The increase of signal strength. Amplification does not improve the signal quality received but can improve the picture quality viewed on TV due to low signal strength.

Attenuation The loss of signal strength. To Attenuate the signal strength is to decrease the level of the signal strength. Attenuation occurs naturally over a length of cable. Refer to cable losses on page 8 for values.

BER Bit Error Ratio is the number of errors in a Video Broadcast. Typically 2 errors in every 1,000,000 will be acceptable.

Forward Gain The amount an antenna increases the signal strength in the air.

Front to Back ratio The difference in signal level received from the front of the antenna verses the back of the antenna. Antennas are designed to reject signals received from the back of the antenna. Good Front to Back ratio reduces the chance of ghosting.

Ghosting Two images of the same source on the one TV Screen caused by two signals received by the same Antenna from two different directions. Often there is the main signal source and a secondary source reflected off a building or mountain.

Losses The signal strength is decreased over cable, splitters and connectors. Compensation for losses must be made when designing a MATV system.

RF Radio Frequency.

Skin effect TV frequencies travel around the circumference of the copper conductor in a coax cable. It is important to make sure that when terminating coax cable for MATV or Satellite TV applications that a properly designed stripping tool is used. Avoid scoring or ringing the copper conductor as TV frequencies travel on the outside circumference of the copper conductor.

UHF Ultra High Frequency. UHF channels are broadcast from channel 21-69. Digital and analogue frequencies.

VHF Very High Frequency. VHF Low are channels 0-5A. analogue frequencies. VHF High are channels 6-12. Digital and Analogue frequencies. Digital TV will only be broadcast on VHF channels 6 and above as well as all UHF channels.

4 Clipsal TV Cabling Solutions Terminology preferred televisionpreferred outletdueto the signal distri forsustained high quality ofa andshouldbe Television ofthecablinginfrastructure arepart outlets Outlet Television have more The withthem. lossesassociated of willenabletheconnection A splitter Splitter mounting theantenna properly. signal possible by thebest Get andextensions. masts wall mounts, mounts, applications such arevariousantenna asroof fordifferent There mounts Mounts thetelevision. cordsvoltage from behind be bending from stress under themost Recorder. Fly asitis Leadshouldalways used Video Digital be quality Agood theoutletto thetelevisionA Fly orrecording device Leadconnects such asa Lead Fly ideal level. signal is Tap too hightheuseofaDrop way is aneasy to getthesignal to the TapA Drop thesignal level willdecrease by asetamount over theTap the If Leg. Drop Tap signals fom2antennas cable. through1coax combineDiplexers TV Diplexer quality. Youresultant picture should theantennafrom to thetelevision wit TelevisionQuality Cable is Coax design Cable Across Australia reference guideforyour to needs. Refer TV frequencies. of types ofantennas that forreceivingdifferent aredesigned types are different signal. There mounted to quality that inalocation be willreceiveneed agood Transmission TV from broadcast Towers. frequencies Antennas receive TV They Antenna signal quality. willincreasethesignal st An amplifier Amplifier only use a good quality cable. quality onlyuseagood bution. F-Type arethe industry outlets quality of connection andperformance. ofconnection quality rength. Amplifiers DO NOT improve DO the rength. Amplifiers hout any to interference thesignal and ed to carry thetelevision to frequencies ed carry hind television andinduced cabinets multiple outlets to 1 antenna. Splitters to 1antenna.multiple outlets Splitters splits thegreater thelosseswillbe. splits

5 TERMINOLOGY TV Signal Strength

TV signal strength is measured in decibel Micro The prime reception area is a location that Volts (dBuV) more commonly known as dB. an antenna with minimal gain can be installed to get the ideal signal range or above at the The ideal signal strength at the television outlet television outlet.

MATV BASICS is 69dBuV. The ideal Signal Range is between 65-72dBuV. An outer fringe reception area is a location that an antenna with maximum amount of gain must Low signals need to be increased. This can be be installed to provide an ideal signal range at the achieved by using a larger antenna with more gain outlet. It is also likely that an amplifier may need or by the use of an amplifier. to be installed to increase the signal level. High signals need to be decreased. This can be achieved by using a drop tap or splitter.

The closer the antenna is to the television MATV Outlet - 69dBuV Standard Outlet - 240V transmitter the higher the signal strength is going to be.

62dBuV 65dBuV 72dBuV 75dBuV

Low Signal Acceptable Signal 69dBuV Acceptable Signal High Signal

By using the same antenna and 20m of RG6 Quad If in a Outer Fringe Area the signal will be lower Shield Coax Cable we can classify the Prime, than 66dBuV. Fringe and Outer Fringe areas by the level of signal To compensate for a Fringe Area reception we can received at the outlet. use an antenna with more forward gain to increase If in a Prime reception area the signal strength will the signal strength at the outlet. be greater than 69dBuV at the outlet. If in a Fringe reception area the signal strength will be greater than 66dBuV at the outlet.

PRIME FRINGE OUTER FRINGE

69dBuV 66dBuV

6 Clipsal TV Cabling Solutions Signal Quality annoying pixilation/blocking can be a matter amatter canbe annoying pixilation/blocking television receptionand quality between Television Digital quality difference Signal. The that inalocation hasagood be itmust installed televisiondigital anantenna signal. When is quality aretheresultPixilation ofpoor orblocking strength. signal than is moreimportant Signal quality PIXILATION the ultimate to location mount theantenna. meter strength to find the antenna andfield Take afewminutes with to walkalongtheroof reception. television digital oftheantennalocation is suitable forhighquality to antenna to make installation sure that the doneprior Asite canbe of afewmetres. survey QUALITY PICTURE QUALITY 7 MATV BASICS Signal Loss - Cable

Losses are a part of any MATV System. You may VHF = Very High Frequency - losses are low. start out with an acceptable signal level at the (0.053dB per meter RG6 Quad Shield). antenna but due to losses in the cable or splitter UHF = Ultra High Frequency - losses are high may not be acceptable when at the outlet. (0.21dB per meter RG6 Quad Shield). MATV BASICS Signal Strength is lost over a length of cable. The As a general rule of thumb cable runs of up to losses are easy to calculate as losses are consistent 50m can be done in RG6. If longer cable runs are per meter. required then you would change the cable size Losses are calculated separately for VHF and UHF to RG11 as the losses on RG11 are much lower. frequencies. The golden rule is the higher the VHF and UHF losses are an average to cover all frequency the higher the loss. We need to calculate frequencies of the VHF and UHF range. This is a losses for both VHF and UHF in every TV design to guide only. See pages 46-49 for cable losses for ensure that we have a balanced system. frequency ranges.

RG6 Cable Losses Frequency 1m 10m 20m 30m 40m 50m

VHF (0-12) 0.053dB 0.53dB 1.06dB 1.59dB 2.12dB 2.65dB

UHF (21-69) 0.21dB 2.1dB 4.2dB 6.3dB 8.4dB 10.4dB

RG11 Cable Losses Frequency 1m 10m 20m 30m 40m 50m

VHF (0-12) 0.032dB 0.32dB 0.64dB 0.96dB 1.28dB 1.6dB

UHF (21-69) 0.131dB 1.31dB 2.62dB 3.93dB 5.24dB 6.55dB

RG6 Quad Shield Coax Cable VHFVHF = 70dB70dB UHF = 70dB

10m 20m20m 30m 40m 50m

VHF = 69.47dB VHF = 68.94dB VHF = 68.41dB VHF = 67.88dB VHF = 67.35dB UHF = 67.9dB UHF = 65.8dB UHF = 63.7dB UHF = 61.6dB UHF = 59.6dB

8 Clipsal TV Cabling Solutions 20m RG6 20m Signal Loss - Splitters - Loss Signal well as losses over cable. cable. over aslosses well taken into be account must losses forsplitters as When the losses. morewaysThe thesignal is splitthehigher timeyou splitthesignal. every is reduced strength have signal The All passive losses. splitters Low Signal LOSSES FOR CLIPSAL TERRESTRIAL SPLITTER RANGE SPLITTER TERRESTRIAL CLIPSAL FOR LOSSES Lounge 65.4 dB 65.4 471-860MHz 471-860MHz 46-470MHz

Frequency 2 Way 3 Way 4 Way 6 Way 8 Way 8 Way 6 Way 4 Way 3 Way 2 Frequency installing oraddingto anantenna,installing the 2BV6du 2BV75dBuV 72dBuV 65dBuV 62dBuV VHF UHF Acceptable Signal Acceptable 20m RG6 20m Ideal Master Bedroom IncomingI Signal ncoming Signa ncoming 65.4 dB 65.4 74 74 74 dBuV 74 Splitter Loss Splitter d 35B<.d 75B<02B<11.2dB <10.2dB <7.5dB <6.1dB <3.5dB 44B<.d <7.8dB <6.3dB <4.4dB 4.4 dB B Cable Loss uV 4.2dB 69dBuV 20m RG6 20m Lounge 62 dB because theseareth because shows below theUHFlossesonly example The picture. at theoutletandresultstrength inpoor canchangethesignal fora4way splitter splitter shows below that changinga2way example The <10.7d B 20m RG6 20m Master Bedroom Acceptable Signal Acceptable <11.8dB 62 dB e highest losses. e highest 0 G 20m RG6 20m RG6 Low IncomingI Signal Bedroom 2 Bedroom ncomi 62 dB High Signal 7 74 dBuV 74 Splitter Loss Splitter 4 d ng Cable Loss 7.8 dB 7.8 B 4.2 dB 4.2 uV Sig n Bedroom 3 Bedroom 62 dB 9 MATV BASICS HIGH PERFORMANCE

ANTENNAS - HIGH PERFORMANCE HIGH - ANTENNAS 13 Element Combination 2ANCOM3

VHF UHF

Channels 1-12 28-50

Forward Gain 8dB 12dB

F/B Ratio >12dB >14dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Prime

13 Element Combination 2ANCOM3WB

VHF UHF

Channels 1-12 28-69

Forward Gain 8dB 12dB

F/B Ratio >12dB >14dB

Connection F-Type

Balun High Perf. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Prime

10 Clipsal TV Cabling Solutions HIGH PERFORMANCE

17 Element Combination 2ANCOM4

VHF UHF

Channels 2-12 28-40

Forward Gain 9dB 12dB

F/B Ratio >12dB >14dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Fringe

28 Element Combination 2ANCOM6 ANTENNAS - HIGH PERFORMANCE

VHF UHF

Channels 2-12 28-40

Forward Gain 10dB 15dB

F/B Ratio >16dB >16dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Outer Fringe

11 HIGH PERFORMANCE

ANTENNAS - HIGH PERFORMANCE HIGH - ANTENNAS Newcastle Antenna 2ANCOM2NEW

VHF UHF

Channels 3 & 5A 28-57

Forward Gain 5dB 13dB

F/B Ratio >17dB >20dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Prime/Fringe

Bunbury Antenna 2ANCOM2SW

VHF UHF

Channels 3 & 5A 30-40

Forward Gain 5dB 13dB

F/B Ratio >11.5dB >18dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Prime/ Fringe

12 Clipsal TV Cabling Solutions HIGH PERFORMANCE

14 Element Combination 2ANCOMD14

VHF UHF

Channels 6-12 28-50

Forward Gain 7.5dB 12dB

F/B Ratio >16dB >16dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Prime/Fringe

14 Element Combination 2ANCOMD14WB ANTENNAS - HIGH PERFORMANCE

VHF UHF

Channels 6-12 28-69

Forward Gain 7.5dB 12dB

F/B Ratio >16dB >16dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Prime/Fringe

24 Element Combination 2ANCOMD24

VHF UHF

Channels 1-12 28-69

Forward Gain 8dB 15dB

F/B Ratio >16dB >16dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap out

U bolt Assembled

Reception Area Fringe

13 2ANCOMCAR None Prime F-Type Assembled F-Type FerriteF-Type Balun 4dB 8dB 0-12 28-69 VHF UHF >10dB >14dB VHF Horizontal VHF UHF Horizontal VHF Vertical VHF UHF Horizontal Balun U bolt F/B RatioF/B Channels Reflectors Connection Forward Gain Reception Area

VHF Vertical VHF UHF Horizontal VHF Horizontal VHF UHF Vertical Caravan Antenna Caravan CARAVAN ANTENNA CARAVAN

Clipsal TV Cabling Solutions

ANTENNAS - CARAVAN 14 32 Element Combination Economy 17 Element Combination Economy 13 Element Combination Economy

Reception Area Reception Reception Area Reception Reception Area Reception Forward Gain Forward Forward Gain Forward Forward Gain Forward Connection Connection Connection Reflectors Reflectors Reflectors Channels Channels F/B Ratio Channels F/B Ratio F/B Ratio U bolt U bolt Balun Balun U bolt Balun ECONOMY MODELS ECONOMY 2d >20dB >20dB 1d >20dB >10dB 8B>20dB >8dB H UHF VHF H UHF VHF -228-69 6-12 -228-36 2-12 H UHF VHF d 7.5dB 5dB d 11dB 8dB -228-36 2-12 d 10dB 6dB Prime/Fringe Ferrite Balun Ferrite Prime/Fringe Ferrite Balun Ferrite Assembled Assembled Assembled Snap Out F-Type F-Type F-Type Prime None None None 2ANCOMA13 2ANCOMA17 2ANVULP2 15

ANTENNAS - ECONOMY MODELS HIGH PERFORMANCE CROSS POLARITY

ANTENNAS - CROSS POLARITY - ANTENNAS 13 Element Cross Polarity Combination 2ANUV13WB

VHF UHF

Channels 6-12 50-69

Forward Gain 7dB 12dB

F/B Ratio >12dB >14dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap Out

U bolt Assembled

Reception Area Prime/Fringe

14 Element Cross Polarity Combination 2ANUV14

VHF UHF

Channels 6-12 28-50

Forward Gain 7dB 11dB

F/B Ratio >12dB >16dB

Connection F-Type

Balun High Perform. PCB

Reflectors Snap Out

U bolt Assembled

Reception Area Prime/Fringe

All vertically mounted antennas will require a 2ANVB15 bracket. Refer to page 31.

16 Clipsal TV Cabling Solutions 19 Element Combination Cross Polarity 16 Element Combination Cross Polarity HIGH PERFORMANCE CROSS POLARITY

Reception Area Reception Reception Area Reception Forward Gain Forward Forward Gain Forward Connection Connection Reflectors Reflectors Channels Channels F/B Ratio F/B Ratio U bolt U bolt Balun Balun 1d >16dB >12dB 1d >14dB >12dB H UHF VHF H UHF VHF -228-69 1-12 -228-50 2-12 d 12dB 7dB d 12dB 7dB High Perform. PCB Perform. High High Perform. PCB Perform. High Prime/Fringe Prime/Fringe Assembled Assembled Snap Out Snap Out F-Type F-Type 2ANUV16 2ANUV19 17

ANTENNAS - CROSS POLARITY UHF UHF 28-69 >14dB 28-69 F-Type 12.5dB >20dB F-Type 14.5dB Snap OutSnap Snap OutSnap Prime/Fringe 2ANUY12WB 2ANUY20WB Elevat. Tilt Bracket High Perform. PCB Elevat. Tilt Bracket High Perform. PCB Fringe/Outer Fringe Balun U bolt Balun U bolt F/B RatioF/B Channels F/B RatioF/B Channels Reflectors Reflectors Connection Connection Forward Gain Forward Gain Reception Area Reception Area Tilt supplied bracket for UHF Antennas

12 Element Yagi Element 12 20 Element Yagi Element 20

UHF YAGI

Clipsal TV Cabling Solutions

ANTENNAS - UHF YAGI 18 18 Element Yagi Band5 18 Element Yagi Band4 10 Element Yagi Band4

Reception Area Reception Reception Area Reception Reception Area Reception Forward Gain Forward Forward Gain Forward Forward Gain Forward Connection Connection Connection Reflectors Reflectors Reflectors Channels Channels F/B Ratio Channels F/B Ratio F/B Ratio U bolt Balun U bolt U bolt Balun Balun UHF YAGIUHF Fringe/Outer Fringe Fringe/Outer High Perform. PCB Perform. High Elevat. Tilt Bracket Tilt Elevat. High Perform. PCB Perform. High High Perform. PCB Perform. High Elevat. Tilt Bracket Tilt Elevat. Elevat. Tilt Bracket Tilt Elevat. 2ANUY18/5 2ANUY18/4 2ANUY10/4 Snap Out Snap Out Snap Out F-Type 13.5dB >20dB 12.5dB F-Type F-Type >20dB Fringe >16dB 35-69 Prime 28-35 28-35 14dB UHF UHF UHF 19

ANTENNAS - UHF YAGI UHF UHF None 21-69 2ANUPA1 Prime None 21-69 >15dB 2ANUPA2 F-Type 8-11dB >20dB F-Type 13.5dB Assembled Rear X Type Assembled Rear X Type Outer Fringe Outer Balun U bolt Balun U bolt F/B RatioF/B Channels F/B RatioF/B Channels Reflectors Reflectors Connection Connection Forward Gain Forward Gain Reception Area Reception Area

8 Element Phased Array Phased 8 Element 16 Element Phased Array Phased Element 16 UHF PHASED ARRAY PHASED UHF Clipsal TV Cabling Solutions

ANTENNAS - UHF PHASED ARRAY 20 43 Element XStyle 23 Element XStyle 91 Element XStyle

Reception Area Reception Reception Area Reception Reception Area Reception Forward Gain Forward Forward Gain Forward Forward Gain Forward Connection Connection Connection Reflectors Reflectors Reflectors Channels Channels Channels F/B Ratio F/B Ratio F/B Ratio U bolt U bolt U bolt Balun Balun Balun UHF XTYPE High Perform. PCB Perform. High High Perform. PCB Perform. High High Perform. PCB Perform. High Elevat. Tilt Bracket Tilt Elevat. Elevat. Tilt Bracket Tilt Elevat. Elevat. Tilt Bracket Tilt Elevat. Outer Fringe Bolt On Bolt On Bolt on F-Type F-Type F-Type >20dB Fringe >20dB >17dB Prime 21-69 21-69 21-69 2ANUX23 2ANUX43 2ANUX91 10dB 13dB 15dB UHF UHF UHF

21 ANTENNAS - UHF X TYPE 2ANVY7 6-12 6-12 6-12 VHF VHF VHF 2ANVY18 2ANVY10 14dB 8.8dB Prime Prime >16dB >16dB >20dB Fringe F-Type F-Type F-Type 11-12dB Snap OutSnap Snap OutSnap Snap OutSnap Assembled Assembled Assembled High Perform. PCB High Perform. PCB High Perform. PCB Balun Balun Balun U bolt U bolt U bolt F/B RatioF/B F/B RatioF/B F/B RatioF/B Channels Channels Channels Reflectors Reflectors Reflectors Connection Connection Connection Forward Gain Forward Gain Forward Gain Reception Area Reception Area Reception Area

18 Element Yagi Element 18 7 Element Yagi 7 Element 10 Element Yagi Element 10

VHF YAGI VHF

Clipsal TV Cabling Solutions

ANTENNAS - VHF YAGI 22 9 Element Periodic Log 8 Element Periodic Log 12 Element Periodic Log

VHF LOG PERIODIC Reception Area Reception Reception Area Reception Reception Area Reception Forward Gain Forward Forward Gain Forward Forward Gain Forward Connection Connection Connection Reflectors Reflectors Reflectors Channels Channels Channels F/B Ratio F/B Ratio F/B Ratio U bolt U bolt U bolt Balun Balun Balun High Perform. PCB Perform. High High Perform. PCB Perform. High High Perform. PCB Perform. High Outer Fringe Assembled Assembled Assembled 2ANV2WB 2ANV3WB 2ANV4WB 6-12dB 5-11dB F-Type F-Type F-Type Fringe >15dB >12dB >15dB 4-8dB Prime None None None VHF VHF VHF 0-12 0-12 0-12 23

ANTENNAS ANTENNAS- VHF LOG PERIODIC- VHFUHF 6-12 6-12 VHF VHF 12dB 2ANVPA1 None None None None 2ANVPA2 >16dB >16dB F-Type F-Type 7-9.5dB Assembled Assembled Prime/Fringe Fringe/Outer Fringe Balun Balun U bolt U bolt F/B RatioF/B F/B RatioF/B Channels Channels Reflectors Reflectors Connection Connection Forward Gain Forward Gain Reception Area Reception Area

8 Element Phased Array Phased 8 Element 16 Element Phased Array Phased Element 16

VHF PHASED ARRAY PHASED VHF

Clipsal TV Cabling Solutions

ANTENNAS - VHF PHASED ARRAY 24 3 Element FM 8 Element FM

Reception Area Reception Reception Area Reception Forward Gain Forward Forward Gain Forward Connection Connection Reflectors Reflectors Channels F/B Ratio Channels F/B Ratio U bolt Balun U bolt Balun Fringe/Outer Fringe Fringe/Outer High Perform. PCB Perform. High High Perform. PCB Perform. High FM Assembled 88-108Mhz Assembled 88-108Mhz F-Type F-Type >15dB Prime >17dB None None 10dB VHF VHF 5dB 2ANFM8 2ANFM3 25

ANTENNAS - FM Curved Fascia Brackets MOUNTING ACCESSORIESMOUNTING

Curved Fascia Brackets

1.2m used for smaller antennas - 2ANCFB12 1.5m used for small to medium antennas - 2ANCFB15 1.8m used for small to medium antennas - 2ANCFB18 1.5m used for larger antennas - 2ANCFBHD

• Mounted to the fascia or wall • Generally used when height of the antenna is not a issue • Used for small to medium sized antennas • Stay bars can be used to support the antenna if required.

26 Clipsal TV Cabling Solutions Stay Bars

Stay Bar

Stay Bar Collar MOUNTING ACCESSORIES

Stay bar set of 2 x 1200mm (4 foot) - 2ANSB4 Stay bar set of 2 x 1800mm (6 foot) - 2ANSB6 Stay bar set of 2 x 2400mm (8 foot) - 2ANSB8 Stay bar collar - 2ANSBC

All stay bars require a stay bar collar for mounting. One end of the stay bar is fixed to the stay bar collar. The other end of the stay bar is fixed to the roof. (Drill through tile to screw to baton for tiled roof) Used to support • Antenna mounts • Curved fascia brackets • Tripod roof mounts • Rafter mounts • Masts.

27 Tripod Roof Mounts MOUNTING ACCESSORIESMOUNTING

Tripod Roof Mount - TILE - 2ANTRPT Tripod Roof Mount - METAL - 2ANTRPM

The easiest way to mount an antenna 2ANTRPT • Drill through tile to baton for fixing with appropriate anchors • Bend the supports to adjust for any roof angle 2ANTRPM • Use existing roof screws to fix mount in place • Bend the supports to adjust for any roof angle

28 Clipsal TV Cabling Solutions Rafter Mounts

Lead Flashing Kit Pipe Rubber Roof Seal MOUNTING ACCESSORIES

Rafter Mount

Rafter Mount - 2ANRM25 - 2ANRM32 Lead Flashing Kit - 2ANLFK Roof Seal - Metal - 2ANPFK

Rafter Mount 1.8m x 25mm - 2ANRM25 Rafter Mount 1.8m x 32mm - 2ANRM32 Lead Flashing Kit (tiled roofs) - 2ANLFK Pipe Rubber Roof Seal (metal Roofs) - 2ANPFK

Smaller antennas use the 2ANRM25 Medium to larger antennas use the 2ANRM32 Tiled roof must use a 2ANLFK Metal roof use the 2ANPFK

29 Wall Mounts/Masts MOUNTING ACCESSORIESMOUNTING

Mast

Wall Mount

Wall Mount 230mm (9inch) - 2ANWB09 Wall Mount 280mm (11inch) - 2ANWB11 Wall Mount 690mm (27inch) - 2ANWB27 Wall Mount 1020mm (40inch) - 2ANWB40 V Block offset Wall Mount 1400mm (55inch) - 2ANWB55 Wall Mount kit (2ANWB9 + 2ANWB27) - 2ANWB17K Mast 3.0m x 32mm - 2ANGM3032 Mast 4.5m x 32mm - 2ANGM4532 Mast 4.5m x 38mm - 2ANGM4538 V Block offset (used to mount horizontal and vertical poles together) 2ANVBO Bolt for V Block - 2ANVB

Used to gain extra height required for better TV reception Mast extensions available for extra height if required.

30 Clipsal TV Cabling Solutions Vertical Stand Off Bracket

Vertical Stand off Bracket MOUNTING ACCESSORIES

Vertical Stand off Bracket 375mm (15 inch) - 2ANVB15

Used to mount an antenna vertically All antennas mounted vertically need a stand off bracket If a stand off bracket is not used signal problems may be encountered.

All vertically mounted antennas will require a 2ANVB15 bracket.

31 Guy Wire Fixing

MOUNTING ACCESSORIESMOUNTING Guy ring plate

Lock ring collar

2ANIRM Guy Wire Iron Roof Mount Mast

2ANGWC Guy Wire Clamp/Grip

2ANTBS Thimble

Turnbuckle

2ANGCC Guy Wire Bracket/Cleatket/Cleat

32 Clipsal TV Cabling Solutions Guy Wire Fixing

Guy Wire 180m reel -2ANGWR Guy Wire Spool (Coiled) - 2ANGW Guy ring plate x 32mm (suites 32mm mast) - 2ANGR32 Guy ring plate x 38mm (suites 38mm mast) - 2ANGR38 Lock ring collar x 32mm (suites 32mm mast) - 2ANLR32 Lock ring collar x 38mm (suites 38mm mast) - 2ANLR38 Guy Wire Cleat - 2ANGC Guy Wire Clamp - 2ANGWC Turnbuckle x 6mm (1/4 inch) - 2ANTBK6 Turnbuckle x 8mm (5/16 inch) - 2ANTBK8 Thimble - 2ANTBS

MOUNTING ACCESSORIES

Mast Extension

Mount fixing points on roof 3m from base of mast Mount guy ring 3m above the base of the mast for 4.5m masts Mount guy ring 2.5m above the base of the mast for 3m masts Use thimbles to stop the guy wire rubbing against the mount Use turnbuckles to tighten the guy wire.

33 Mast Extensions MOUNTING ACCESSORIESMOUNTING

Mast

Mast Extension - 2ANME Mast Extension Kit - 2ANMEK Mast 3.0m x 32mm - 2ANGM3032 V Block offset Mast 4.5m x 32mm - 2ANGM4532 Mast 4.5m x 38mm - 2ANGM4538 V Block offset (used to mount horizontal and vertical poles together) - 2ANVBO

Wall Mounts/Masts

Used to get extra height required for better TV reception May require some form of support • Guy wire support • Stay bar support

34 Clipsal TV Cabling Solutions Mast Extension Kit

V Block clamps two poles together such as a mast to a wall/eave bracket. MOUNTING ACCESSORIES

Mast Extension Kit - 2ANMEK

Mast Extension

Mast Extension- 2ANME

35 Flat Wall Mount MOUNTING ACCESSORIESMOUNTING

Wall Bracket

Mast

Flat Wall Mount Bracket - 2ANFWM

Metal Fascia

Metal Fascia - 2ANMFB

36 Clipsal TV Cabling Solutions V Block

2ANUBM or 2ANUBL U Mount 2ANVB Block

V Block clamps at 90 degrees to the mast. This is ideal for horizontal mounting of antennas.

V Block - 2ANVB MOUNTING ACCESSORIES U Bolt 5 inches - 2ANUBM U Bolt 7 inches - 2ANUBL

V Offset Block

V Offset Block - 2ANVBO U Bolt 5 inches - 2ANUBM U Bolt 7 inches - 2ANUBL

37 3105SPF2 3105SPF4 3105SPF3 2 1 2 1 2 1 1 port 1 port 1 port F-Type F-Type <7.5dB <7.8dB <4.4dB <3.5dB F-Type <6.1dB <6.3dB Power Pass Power Pass Power Pass Mounting Holes Mounting Mounting Holes Mounting Mounting Holes Mounting Connection Type Connection Type Connection Type Earthing Connection Earthing Connection Earthing Connection Losses VHF 46-470MHz Losses VHF 46-470MHz Losses VHF 46-470MHz Losses UHF 471-860MHz Losses UHF 471-860MHz Losses UHF 471-860MHz Not suitable for Satellite Television Transmission Not suitable for Satellite Television Transmission Notsuitable for Satellite Television Transmission

4 Way Terrestrial Splitter 5-1000MHz Terrestrial 4 Way 2 Way Terrestrial Splitter 5-1000MHz Terrestrial 2 Way 3 Way Terrestrial Splitter 5-1000MHz Terrestrial 3 Way

Clipsal TV Cabling Solutions

SPLITTERS 38 Power Pass Power Pass 8 Way Terrestrial 5-1000MHz Splitter 6 Way Terrestrial 5-1000MHz Splitter 70dB

54dBuV

11.8dB 11.8dB 4.2dB Only UHFlossesareshown purposes forillustration Only Not suitable for Satellite Television Transmission Television Satellite for suitable Not Not suitable for Satellite Television Transmission Television Satellite for suitable Not 20m CableLoss 20m Splitter Loss Splitter Losses UHF 471-860MHz UHF Losses Losses UHF 471-860MHz UHF Losses Losses VHF 46-470MHz VHF Losses Losses VHF 46-470MHz VHF Losses Earthing ConnectionEarthing Earthing ConnectionEarthing Connection Type Connection Connection Type Connection Mounting Holes Mounting Holes Power Pass Power Power Pass Power <11.8dB <11.2dB <10.2dB <10.7dB F-Type F-Type 1 port 1 port 1 2 1 2 3105SPF8 3105SPF6 39

SPLITTERS 4 8 No No Yes Yes 3105VDU24T ·Local ·Local 12VDC 12VDC +3dB Gain +3dB Gain 37-860Mhz 37-860Mhz 3105VDU38IRT 1x Antenna1x Input 1x Antenna1x Input -15dB Attenuation-15dB -15dB Attenuation-15dB Antenna Input only Antenna Input only 1x Modulated1x Input 2x Modulated Inputs ·Remote via Modulator ·Remote via Modulator All Free Air to Channels All Free to Air Channels ·Remote via Power Injector ·Remote via Power Injector Input Ports Input Ports IR Pass Back Pass IR IR Pass Back Pass IR Output Ports Output Output Ports Output Power Supply Power Supply 3 Power Options 3 Power Options Frequency Range Frequency Frequency Range Frequency IR Expansion Port IR Expansion Port Variable Gain Control Variable Gain Control 2dB 70dB Gain Control + Gain Control

72dB Powered Splitter 37-860MHz Powered Splitter 37-860MHz 67.8dBuV 4.2dB 4.2dB

20m Cable Loss

Clipsal TV Cabling Solutions

SPLITTERS 40 20m CableLoss 20m 4.2dB 8 Way Powered 37-860MHz Splitter 67.8dBuV 6 Way Powered 37-860MHz Splitter 72dB

70dB Gain ControlGain + Variable Gain Control Gain Variable 2dB Variable Gain Control Gain Variable IR Expansion Port Expansion IR Frequency Range IR Expansion Port Expansion IR Frequency Range 3 Power Options 3 Power 3 Power Options 3 Power Power Supply Power Power Supply Power Output Ports Output Ports IR Pass Back IR Pass Back Input Ports Input Input Ports Input ·Remote via Power Injector Power via ·Remote ·Remote via Power Injector Power via ·Remote All Free to Air Channels toAir Free All ·Remote via Modulator via ·Remote All Free to Air Channels toAir Free All ·Remote via Modulator via ·Remote 2x Modulated Inputs Modulated 2x Antenna Input only only Input Antenna 1x Modulated Input 1x Modulated Antenna Input only only Input Antenna -15dB Attenuation -15dB Attenuation 1x Antenna Input 1x Antenna 1x Antenna Input 1x Antenna 37-860Mhz 37-860Mhz +3dB Gain +3dB +3dB Gain +3dB 12VDC 12VDC ·Local 8073/8VHPIR ·Local Yes Yes No No 8 6 8072/6VHP 41

SPLITTERS 3105SPFP2 3105SPFP3 3105SPFP4 2 1 2 1 2 1 N/A N/A N/A N/A <9dB F-Type F-Type <7.5dB <4.6dB <5.3dB <6.3dB F-Type A01564 <8.5dB A01592 <11.5dB All ports <11.5dB All ports <10.5dB All ports F10082/C F10082/C F10082/C Approval Number Approval Approval Number Approval Approval Number Approval Foxtel Foxtel Austar Austar Foxtel Austar Select TVSelect Select TVSelect Select TVSelect Power Pass Power Pass Power Pass Mounting Holes Mounting Mounting Holes Mounting Mounting Holes Mounting Connection Type Connection Type Connection Type Losses 40-1000MHz Losses Losses 40-1000MHz Losses Losses 40-1000MHz Losses Earthing Connection Earthing Connection Earthing Connection Losses 1751-2050MHz Losses Losses 1751-2050MHz Losses Losses 1000-1750MHz Losses Losses 1000-1750MHz Losses Losses 1751-2050MHz Losses Losses 1000-1750MHz Losses

3 Way Satellite Splitter 5-2400MHz Satellite 3 Way 2 Way Satellite Splitter 5-2400MHz Satellite 2 Way 4 Way Satellite Splitter 5-2400MHz Satellite 4 Way

Clipsal TV Cabling Solutions

SPLITTERS 42 Diplexers combine TV signals 2antennas from cable. through1coax combineDiplexers TV Outdoor Diplexer DiplexerIndoor

3105DPOUV 3105DPUV

43 DIPLEXERS 1 Way Drop Tap 5-2400MHz 3105T1/XX DROP TAPS 3105T1/10 3105T1/12 3105T1/15 3105T1/20

Tap Loss 10dB 12dB 15dB 20dB

Through Loss 5-950MHz <2dB <1.9dB <1.3dB <0.9dB

Through Loss 951-2400MHz <3dB <2.7dB <2.2dB <1.7dB

Power Pass 1 Port 1 Port 1 Port 1 Port

Connection Type F-Type F-Type F-Type F-Type

Mounting Holes 2222

Earthing Connection 1111

Approval Number

Foxtel F10082-85/C F10082-85/C F10082-85/C F10082-85/C

Austar A01536 A01537 A01538 A01539

Select TV Yes Yes Yes Yes

2 Way Drop Tap 5-2400MHz 3105T2/XX

3105T2/10 3105T2/12 3105T2/15 3105T2/20

Tap Loss 10dB 12dB 15dB 20dB

Through Loss 5-950MHz <2dB <1.9dB <1.5dB <1dB

Through Loss 951-2400MHz <3dB <2.7dB <2.3dB <1.9dB

Power Pass 1 Port 1 Port 1 Port 1 Port

Connection Type F-Type F-Type F-Type F-Type

Mounting Holes 2222

Earthing Connection 1111

Approval Number

Foxtel F10082-85/C F10082-85/C F10082-85/C F10082-85/C

Austar N/A A01541 A01542 A01543

Select TV Yes Yes Yes Yes

4 Way Drop Tap 5-2400MHz 3105T4/XX

3105T4/10 3105T4/12 3105T4/15 3105T4/20

Tap Loss 10dB 12dB 15dB 20dB

Through Loss 5-950MHz <6.5dB <4dB <3dB <1.8dB

Through Loss 951-2400MHz <9dB <4.5dB <4.1dB <1.1dB

Power Pass 1 Port 1 Port 1 Port 1 Port

Connection Type F-Type F-Type F-Type F-Type

Mounting Holes 2222

Earthing Connection 1111

Approval Number

Foxtel F10082-85/C F10082-85/C F10082-85/C F10082-85/C

Austar A01544 N/A A01545 A01546

Select TV Yes Yes Yes Yes

44 Clipsal TV Cabling Solutions Pack of10. to thesystem. connected with TVs interfering reflections electrical terminatedbe witha75 Terminator Ohm to stop Tap ofaDrop should ports All unused orSplitter 75 Ohm Terminator Ohm 75

3105FTER 45

DROP TAPS RG6

RG6 Coaxial Tri Shield Cable 3105RG6T3B COAXIAL CABLE - RG6

Foil Tape

AWG Conductor

Gas injected Foam

PVC Jacket Aluminium Braid

Catalogue Foxtel Austar Description Pack Size Number Approval No. Approval No.

3105RG6T3B RG6 Coax Tri Shield Box 305m Box F10176 N/A

Conductor Size Nom. O.D Insl. & Core AWG Cond. Type Shield Type (mm) (mm) O.D (mm)

60% Aluminium 1.02 +_ 0.03 18 Solid 7.06 +_ 0.02 4.78 +_ 0.13 Braids

5MHz 55MHz 211MHz 250MHz 270MHz 300MHz 330MHz 350MHz 400MHz 450MHz 500MHz 550MHz 600MHz 750MHz 870MHz 1000MHz 1450MHz 1750MHz 2050MHz

1.90 5.25 10.00 10.82 11.04 11.64 12.26 12.63 13.61 14.43 15.29 16.08 16.73 18.54 20.04 21.49 26.25 28.67 31.04

Attenuation @ 20˚C (dB/100m)

46 Clipsal TV Cabling Solutions 5 .052 00 08 10 16 22 26 36 44 52 60 67 85 00 14 62 86 31.04 28.67 26.25 21.49 20.04 18.54 16.73 16.08 15.29 14.43 13.61 12.63 12.26 11.64 11.04 10.82 10.00 5.25 1.90 MHz RG6 Coaxial Quad ShieldCable Quad RG6 Coaxial 55 MHz 211 15GQ1RR6Ca udSil ims 5.mRe 342P07984 F30432 152.5m Reel Siamese Shield Quad Coax RG6 3105RG6QS15R 15GQR G oxQa hedFodd35 elF05 P07985 F30059 Reel 305m Flooded Shield Quad Coax RG6 3105RG6Q3RF 15GQBR6Ca udSil 0mBxF02 P07982 F10129 Box 305m Shield Quad Coax RG6 3105RG6Q3B 15GQRR6Ca udSil 0mRe 119P07982 F10129 Reel 305m Shield Quad Coax RG6 3105RG6Q3R 15GQRR6Ca udSil o 0mRe 119P07982 F10129 Reel 100m Box Shield Quad Coax RG6 3105RG6Q1R MHz Catalogue Number 250 MHz Conductor Size .2 00 18 1.02 0.03 270 (mm) MHz + _ 300 MHz 330 AWG Cond. Type Shield Type Shield Type Cond. AWG MHz ecito Pack Size Description 350 MHz Attenuation @20˚C (dB/100m) Attenuation 400 BCCS Solid MHz 450

MHz 60% & 40% &40% 60% Aluminium 500 Braids MHz 550 MHz 7.54 0.02 4.78 0.13 4.78 7.54 0.02 Nom. O.D O.D Nom. 600 (mm) + _ MHz Approval No. 750 Siamese Quad Shield Quad Siamese Foxtel Foxtel MHz Insl. & Core &Core Insl. O.D (mm) O.D 870 + _ MHz Approval No. 1000 3105RG6Qxxx Austar Austar MHz 1450 MHz RG6 1750 MHz 2050 MHz 47

COAXIAL CABLE MHz 2150 MHz 1770 MHz 1550 MHz _ 1300 + Austar MHz O.D (mm) Insl. & Core Approval No. Approval 1000 MHz _ + 870 3105RG11Q3R, 3105RG11Q3RF (mm) Nom. O.D Foxtel MHz 750 Approval No. Approval MHz 600 (m) 305 10.34 0.25 0.15 7.32 MHz Reel Length Reel 550 MHz 500 MHz 60% & 40% 450 Aluminium Braids Aluminium MHz Attenuation (dB/100m) @ 20˚C 400 MHz Description Size Pack 350 MHz 330 AWG Cond. Type Shield Type MHz 300 MHz 270 _ + (mm) MHz 1.63 0.031.63 14 Solid BCCS Number 250 Catalogue Catalogue Conductor Size Size Conductor 3105RG11Q3R Reel Shield Quad Coax RG11 Reel 305m F10175 A02629 3105RG11Q3RF Reel Flooded Shield Quad Coax RG11 Reel 305m F30060 P07986 RG11 Coaxial Quad Shield Cable Shield Quad Coaxial RG11 MHz 211 RG11 MHz 55

MHz 1.25 3.15 6.23 6.72 7.00 7.38 7.71 7.94 8.53 9.02 9.51 9.97 10.43 11.97 13.31 14.27 16.00 17.42 19.58 21.61 5

Clipsal TV Cabling Solutions

COAXIAL CABLE - RG11 48 RG59 Cable Shield Dual Coaxial 5 .267 24 34 38 461.91.51.31.21.01.22.42.72.526.64 24.85 22.87 20.34 19.52 18.70 17.72 16.73 15.75 15.29 14.6 13.85 13.45 12.47 6.73 2.82 MHz 15G93 G9Ca ulSil o 0mBxNAN/A N/A Box 305m Box Shield Dual Coax RG59 3105RG59D3B 15G91 G9Ca ulSil 0mRe / N/A N/A Reel 100m Shield Dual Coax RG59 3105RG59D1R Catalogue 55 Number MHz Conductor Size 211 MHz 0.81 1 20 Solid BCCS Solid 20 1 0.81 (mm) + _ 250 MHz 270 MHz AWG Cond. Type Shield Type Shield Type Cond. AWG 300 ecito Pack Size Description MHz 330 Attenuation @20˚C (dB/100m) Attenuation MHz 350 MHz 60% Aluminium Aluminium 60% 400 MHz Braids 450 MHz 500 Nom. O.D O.D Nom. MHz 6.10 0.2 3.86 0.13 3.86 6.10 0.2 (mm) 3105RG59D1R, 3105RG59D3B 3105RG59D1R, + _ Approval No. 550 MHz Foxtel Foxtel 600 Insl. & Core O.D O.D &Core Insl. MHz (mm) + _ 750 Approval No. MHz Austar 870 MHz RG59 1000 MHz 49

COAXIAL CABLE RG59 RG6 COMPRESSION

RG6 Compression Tool 3105CT611C COAXIAL CABLE CONNECTORS

Easy to use

Swivel Head for RG6 and RG11

For use with the following connectors:

3105RG6FC50 - RG6 (Packet of 50)

3105RG11FC2 - RG11 (Packet of 2)

RG6 Compression Connector 3105RG6FC50

3105RG6FC50 (Packet of 50)

Approval Number

Foxtel F30029

Austar A06948

Select TV Not Required

RG6 & RG59 Cable Stripper 3105CS6

Easy to use - Termination techniques on pages 54-55

Suits RG6 and RG59 cables

50 Clipsal TV Cabling Solutions G1CbeSrpe RG11R CableStripper RG11 Connector Compression RG11 Compression Tool G11 CableStri pp er

Suits RG11Suits Cables Coax to use Easy A06949 Required Not F30360 TV S Select A Austar Fox Foxtel 3105RG11FC23 2) of (Packet 3105RG11FC2 -RG11 3105RG6FC503105R -RG6 connectors: following the with use u For For RG11 and RG6 for Head Swivel S touse Easy E 10 el u wiv asy asy s e 5 e t s RG11 COMPRESSION Approval Number 3105RG11FC2 3105CT611C 3105CS11

51 COAXIAL CABLE CONNECTORS 3105CS6 3105RG6F 3105CT611 Approval Number Approval FoxtelAustarSelect TV F10179/C Not Required A01509 Easy to use Suits RG6 and RG59 Cables 3105RG6F (Packet3105RG6F of 10) For use with Radial Crimp Tool Easy to use For use with the following connectors: 3105RG59F, 3105BNC6, 3105BNC59 3105RG6F, 3105RG6PM, 3105RG6PF RG6 Radial Crimp Tool Crimp RG6 Radial RG6 Cable Stripper RG6 Cable Stripper RG6 Crimp ConnectorRG6 Crimp RG6 RADIAL CRIMP RADIAL RG6 Clipsal TV Cabling Solutions

COAXIAL CABLE CONNECTORS 52 RG59 Compression Connector Compression RG59 RG59 CableStripper RG59 RadialCrimp Tool Suits RG6 and RG59 Cables RG59 and RG6 Suits to use Easy For use with radial Crimp Tool Crimp radial with use For 10 of Packet 3105RG59F 3105RG6F, 3105RG6PM, 3105RG6PF 3105RG6PM, 3105RG6F, 3105BNC59 3105BNC6, 3105RG59F, connectors: following the with use For touse Easy RG59 RADIAL CRIMP 3105RG59F 3105CT611 3105CS6

53 COAXIAL CABLE CONNECTORS Fold back the firstFold braid then fold back the first back braid but DO the second foil. Fold bonded is to this as last foil the remove NOT the Dielectric. back braid and foil evenly Fold in each direction the connector ensure to A good should preparation slides on easily. diagram. the following look like the shielding. Hold stripping the by tool from without cable and pull away the jaws of the strippingopening tool. the jaws The stripped the following cable will look like diagram. Do’s and Don’ts and Do’s Insert the stripping with tool coax cable into with the lip on the the end of the coax level Hold the hand side. the cable close to right around a few times. and spin tool Not enough the coax stripping of the spins will leave tool will cut away spins on and too many jacket Clipsal TV Cabling Solutions

INSTALLATION TIPS 54 with the base oftheconnector.with thebase connector. termination level shouldbe Agood Slide thecableupto ofthe thebase Once the connector has been installed correctly on correctly installed hasbeen Once theconnector atthe cable. thefront Look oftheconnector. If itwilldamage at ananglebecause connector NOT slide DO onstraight. Slide theconnector O slidonat ananglewillresult A connector Do’s and Don’ts nce t h e connector e connector h as b een insta een ll e d correct in the cable looking like thefollowing diagram. in thecablelooking ly on b ly ly thenshouldyou usethetool to terminate. l l it will look likeit willlook thefollowing diagram. thecableis inside When theconnector DO NOT terminateDO connector. again. andstart the connector thenremovethe cableis damaged ki ng l ik e th e fo ll ow

55 INSTALLATION TIPS Digital Terrestrial Meter 2ANDTM

INSTALLATION TOOLS Features and Benefits

Displays RF level and post BER together with S/N on large display in real time. Run time in excess of five hours on a full charge. Built-in charger with rechargeable NiMH battery.

Specifications

VHF 6-12 UHF 21-69 VHF Band 3 and UHF e.g. 167-862 MHz 7 M Bandwidth Automatic Constellation and transmitter offset C/N up to 32dB in 0.5dB steps accuracy +-1dB RF level 25dBuV to 75dBuV accuracy +-1dB over all bandwidth and under indication Input range -72dBm-20dBm Charger 100-240V Ac or 12V Dc Battery 2.4 Ah NiMH 7.2V 6 cell BCN - PAL + BCN F-Type adaptors included 2x 10dB attenuators included

This meter is a Digital Field Strength Meter and will not measure any channel below VHF 6.

56 Clipsal TV Cabling Solutions Digital Field Strength Meter

Step Through V 6 RF Level 72dBuV IIIIIIIIIIIIIIIIIIIII------DVB-T

RF Screen Allows you to scrolloll through VHF and UHF channels and measure the signal strength.strength

Step Through Use the arrow buttons to scroll through VHF and UHF channels.

RF Level Shows the level of signal strength numerically. INSTALLATION TOOLS INSTALLATION

IIIIIIIIIIIIIII Bar reading of signal strength.

DVB-T This will appear if the signal is a digital video broadcast terrestrial. If this appears then press the ON button to change to the BER page. If this does not appear the signal is an analogue signal.

Step Through V 6 BER 0.00E7 **** PASS IIIIIIIIIIIIIIIIIIIII------SN 29dB

BER Screen Measures the Bit Error Ratio.

Step Through Use the arrow buttons to scroll through the VHF and UHF channels.

BER Shows the number of errors within the signal. Use to measure the quality of the digital signal only.

PASS PASS or FAIL will appear dependant on the number of errors.

IIIIIIIIIIIIIII Bar reading of signal strength.

SN 29dB Signal to Noise Ratio. Measures the amount of signal versus electrical noise within the cable. The higher the number the better.

57 MATV Tool Box 3105TOOLBOX INSTALLATION TOOLS

Clipsal Australia have provided a MATV tool box that has the essentials required to carry out MATV installations. Refer to chart below for the great range of products included.

Product Cat No.No. Qty.Qty.

Compression Tool3105CT611 3105CT611CC 1

Hex Crimp Tool 3105CT611C 1

Coax Cable Stripper 3105CS6 1

Hex Nut Spanner - 1

Coax Cable Cutters - 1

UTP Cable Stripper - 1

2 Way Splitter Terrestrial 3105SPF2 4

3 Way Splitter Terrestrial 3105SPF3 4

4 Way Splitter Terrestrial 3105SPF4 4

2 Way Splitter Satellite 3105SPFP2 4

3 Way Splitter Satellite 3105SPFP3 4

4 Way Splitter Satellite 3105SPFP4 4

F-Type Compression Connectors 3105RG6FC50 50 Connectors

F-Type Radial Crimp Connectors 3105RG6F 50 Connectors

PAL Crimp Connectors 3105RG6PM 50 Connectors

F-Type to F-Type Adaptors - 20 Adaptors

58 Clipsal TV Cabling Solutions Right AngleAdaptorRight Foxtel approval number: F30356 approvalFoxtel number: 10 of Pack Rated to 3GHz

Wall mounted Plasma/LCDWall scenario mounted with rightwith angleadaptor. 20mm 20 40 mm m

mm

m

y cavity cavit Wall Wall 3105FF-FMRA 59

MATV ADAPTORS F-TYPE ADAPTORS

F-Type to RCA Adaptor 3105FF-RCA MATV ADAPTORS - F-TYPE - ADAPTORS MATV

Pack of 1

F-Type to RCA Adaptor 3105FF-BNC

Pack of 1

F-Type Female to Female Coax Joiner 3105FF-FF

Pack of 10

60 Clipsal TV Cabling Solutions F-TYPE TO PAL ADAPTORS

F-Type Female to PAL Male Adaptor 3105PM-FF

Pack of 10

F-Type Female to PAL Female Adaptor 3105PF-FF MATV ADAPTORS - F-TYPE TO PAL

Pack of 10

F-Type Male to PAL Female Adaptor 3105PF-FM

Pack of 10

61 PAL ADAPTORS

PAL Male to PAL Male 3105PM-PM MATV ADAPTORS - PAL - ADAPTORS MATV

Pack of 10

PAL Female to PAL Female Adaptor 3105PF-PF

Pack of 10

62 Clipsal TV Cabling Solutions PAL Maleto PAL Female -RG59 white 1.8m to PALF-type MaleFly ShieldBlack1.8m Lead-RG6Quad PAL Maleto PAL Male-RG59 white 5m to PALF-type MaleFly ShieldWhite Lead-RG6Quad 1.8m PAL Maleto PAL Male-RG59 white 1.8m 3105FL318MWQ 3105FL318MBQ 3105FL150MW 3105FL118MW 3105FL118FW 63

FLY LEADS 3RCA to 3RCA Lead 1.8m 3105AVL318 FLY LEADS

3RCA to 3RCA High Quality Lead 1.8m 3105AVL318HQ

Scart - 6 RCA Lead 1.8m 3105SC-6RCA

Scart - Scart Lead 1.8m 3105SC-SC

64 Clipsal TV Cabling Solutions Screw Termination to PAL F-Type to PAL TV Outlet Straight F-Type to PAL TV Outlet AC Isolation F-Type to F-Type Outlet TV F-Type to PAL TV Outlet Angled Not suitable for satellite TV applications suitableNot forsatellite TV applications suitableNot forsatellite TV applications suitableNot forsatellite TV G135 approvalFoxtel number: approved outletratedPay to 3GHz. TV Not suitable for satellite TV applications suitableNot forsatellite TV To late released 2007. be 30TV75MACF 30TV75MS 30TV75MF 30FFPFMS 30PFM 65

TV MECHS 2031/1F 2031VTV75 2031VTV75F C2031VTV75 C2031VTV75 C2031VTV75F C2031VTV75F C2031/1F C2031/1F 2031VTV75 2031VTV75F 2000 Series 2000 2000 Series 2000 2000 Series 2000 C2000 Series C2000 C2000 Series C2000 C2000 Series C2000

Single Gang Wall Plate Gang Wall Single Single Gang Wall Plate Gang Wall Single Single Gang Wall Plate Wall Gang Single This wall plate contains the Clipsal 30TV75MS TV 30TV75MS the Clipsal contains This wall plate Mech This wall plate contains the Clipsal 30TV75MF TV 30TV75MF the Clipsal contains This wall plate Mech Screw style This wall plate contains the Clipsal 30PFM TV 30PFM the Clipsal Mech contains This wall plate

Clipsal TV Cabling Solutions

WALL PLATES 66 1x C2034VH 4 Gang Wall 4Gang Plate F-Type Mech TV C2034VH Cat 5e data outlets 30RJ88SMA5 1x 30PFM 2x 2x the following Clipsal products: wallplate madeupof wired canbe smart This Wall 4Gang Plate F-Type Mech TV C2034VH Cat 5e data outlets 30RJ88SMA5 1x 30PFM 1x 3x Clipsal products: wallplateThis madeupofthefollowing canbe 1x C2033VH 3 Gang Wall 3 Gang Plate F-Type Mech TV C2033VH 30PFM 1x 3x Clipsal products: wallplateThis madeupofthefollowing canbe areas. mainentertainment Star Serve wallplateThis is for theminimumrequirement StarServe Wall Plate Wall StarServe StarServe Wall Plate Wall StarServe Plate Wall StarServe C2034RJA5/3F C2034RJA5/2F C2033/3F C2034RJA5/2F C2034RJA5/3F 2034RJA5/2F 2034RJA5/3F C2033/3F 2033/3F 67

WALL PLATES 2033RJA5/1F 2032RJA5/1F C033RJA5/1F 2034RJA5/1F C032RJA5/1F C034RJA5/1F C034RJA5/1F C033RJA5/1F C032RJA5/1F StarServe Wall Plate StarServe Wall Plate StarServe Wall Plate This wall plate is ideal for the study. is wall plate This can be following made up of the This wall plate products: Clipsal 1x 3x 30PFM 1x 30RJ88SMA5 outlets data 5e Cat C2034VH TV Mech F-Type Plate 4 Gang Wall Suggested minimum cabling to all bedrooms. all to cabling Suggested minimum can be made up of the following This wall plate products: Clipsal 1x 2x 30PFM 1x 30RJ88SMA5 outlets data 5e Cat C2033VH TV Mech F-Type Plate 3 Gang Wall Suggested minimum cabling to all bedrooms. all to cabling Suggested minimum can be made up of the following This wall plate products: Clipsal 1x 1x 30PFM 1x 30RJ88SMA5 outlets data 5e Cat C2032VH TV Mech F-Type Plate 2 Gang Wall

Clipsal TV Cabling Solutions

WALL PLATES 68 ADELAIDE

Port Gawler Virginia Williamstown Yattalunga Penfield Elizabeth One Tree Hill St Kilda Salisbury Outer Harbour Greenwith Upper Hermitage Parafield Largs Bay Houghton Ethelton Enfield Port Adelaide Paradise Adelaide Montacute Lobethal

Skye LOCATION GUIDES

Woodside Glenelg Malvern

Lynton Brighton Stirling

Marino Hahndorf Cherry Gardens Hallett Cove Reynella Clarendon Echunga Morphett Vale Port Noarlunga

McLaren Vale Maslin Beach The Range

2ANCOM3

2ANCOM4 or 2ANCOM6

2AN 2ANUY12WB or 2ANUY20WB (Multiple Outlets)

2ANV2WB + 2ANUY12WB (Requires Diplexer refer to page 43)

69 MELBOURNE LOCATION GUIDES LOCATION

2ANCOM3

2ANCOM4

2ANUPA2

2ANUY18/5

70 Clipsal TV Cabling Solutions SYDNEY LOCATION GUIDES

2ANCOM3

Inner city Kings Cross translator line-of-sight use 2ANUPA1 or 2ANUX43 2ANCOM4 or 2ANYV10 +2ANUY20WB (Requires Diplexer refer to page 43) 2ANCOM6 or 2ANVY10 + 2ANUX91 (Requires Diplexer refer to page 43)

2ANUY20WB

2ANUPA2

71 NEWCASTLE LOCATION GUIDES LOCATION

2ANCOMD14WB

2ANCOMD14WB + Masthead Amplifier

2ANCOM2NEW For Nelson Bay, call Clipsal for options

2ANUY12WB

2ANUY20WB

2ANUPA2

72 Clipsal TV Cabling Solutions BRISBANE LOCATION GUIDES

2ANCOM3

2ANCOM4

2ANCOM6

73 SOUTH QUEENSLAND LOCATION GUIDES LOCATION

2ANCOM3 or 2ANCOM4 (Multiple Outlets) 2ANUY12WB or 2ANUY20WB (Multiple Outlets)

2ANUPA2

2ANCOMD14WB or 2ANVY10 + 2ANUY20WB (Requires Diplexer refer to page 43)

74 Clipsal TV Cabling Solutions PERTH Two Rocks

Bullsbrook Quinns Rocks

Joondalup

Red Hill Malaga Chidlow Scarborough Midland Piesse Brook Mt Claremont PPertherth Peppermint Grove Kalamunda Reservoir Fremantle LOCATION GUIDES Canning Mills

Wungong Garden Island Cardup Rockingham Oldbury

Mandurah

Dawesville Blythewood

2ANCOM3

2ANCOM4

2ANCOM6

75 When it comes to antenna installation, the choice is clear

Product of Clipsal Australia Pty Ltd International Enquiries You can fi nd this brochure and many others online in PDF format at: clipsal.com A member of the Schneider Electric Group International Sales and Marketing Telephone + 61 8 8269 0587 Follow the links off the home page or access Head Offi ce Facsimile + 61 8 8340 7350 the following page directly: 12 Park Terrace, Bowden E-Mail [email protected] clipsal.com/wat_lib_pdf.cfm South Australia 5007 Telephone (08) 8269 0511 New Zealand Facsimile (08) 8340 1724 Clipsal Industries (NZ) Ltd Internet clipsal.com Telephone (09) 576 3403 E-Mail [email protected] Facsimile (09) 576 1015 Clipsal Australia Pty Ltd reserves the right to change specifi cations, modify designs and discon tin ue items E-Mail headoffi [email protected] National Customer Service Enquiries: without incurring obligation and whilst every effort is Customer Service made to ensure that descriptions, specifi cations and 1300 2025 25 other infor ma tion in this catalogue are correct, no Free Fax (0508) 250 305 National Customer Service Facsimile: warranty is given in respect thereof and the company Auckland/Mobile Phone (09) 572 0014 shall not be liable for any error therein. 1300 2025 56 Free Phone (0508) CLIPSAL 2547725 © Clipsal Australia Pty Ltd. D2-004

CLIPCOM 11954 Aug 2007 The identified trademarks and copyrights are the property of Clipsal Australia Pty Ltd unless otherwise noted. O/N 11954