Model: Parts Page Reorder No. PD02•19 52224 – 6mm Collet, 15,000 RPM Effective April, 2002 52225 – 6mm Collet, 18,000 RPM Supersedes PD96•72 52226 – 6mm Collet, 20,000 RPM 52227 – 6mm Collet, 20,000 RPM* .7Hp/7˚/Short Shank/Front Exhaust 52288 – 1/4" Collet, 15,000 RPM 52289 – 1/4" Collet, 18,000 RPM 52290 – 1/4" Collet, 20,000 RPM Die Grinder 52291 – 1/4" Collet, 20,000 RPM* (*Includes 53163 Side Handle) Machine and Motor Parts

Always operate, inspect and maintain this tool in accordance with the Safety Code for portable air tools (ANSI B186.1) and any other applicable safety codes and regulations. Please refer to Dynabrade's Warning/Safety Operating Instructions for more complete safety information.

1 34 N•m T 2 3 4 5 6 8 9 10 12 13 14

7 7 A8 15 Index Key 11 O1 No. Part # Description Left Hand Threads 16 1 Collet Assembly 50010 1/4" KEY 50015 6mm O Oil: O1 = Air Lube 45 N•m T 17 2 Exhaust Cover 01734 15,000 RPM A Adhesive: A8 = Loctite #567 01738 18,000 RPM 01748 20,000 RPM 18 Torque: N•m x 8.85 = In. - lbs. 3 01744 Silencer T 4 01007 Bearing 5 01121 Shim (3/pkg.) 6 01008 Plate 7 50767 Guide Pin (2) 19 8 01010 Spacer 9 01028 Cylinder T 23 N•m 10 55021 Rotor 20 11 01185 Blade (4/Pkg.) 12 01743 Bearing Plate 21 A8 O1 13 02649 Bearing 14 01739 Motor Housing 15 01437 Plug 16 01548 Gasket 17 01461 Lock Nut 18 01558 Collar A8 22 19 01448 Throttle Lever 01462 Safety Throttle Lever 20 12132 Pin Right Hand Threads 27 28 29 30 31 21 95558 Retaining Ring 23 22 Housing (See Chart) 23 01449 Valve Stem 24 24 95730 O-Ring Valve Body 25 01024 O-Ring 01622 – Model 52224 25 26 01469 Speed Regulator Assy. 01623 – Model 52225 27 01464 Seal 01624 – Model 52226 26 28 01472 Tip Valve 01625 – Model 52227 29 01468 Spring 02139 – Model 52288 30 01494 Inlet Bushing 02140 – Model 52289 02141 – Model 52290 31 50033 Hanger 02141 – Model 52291

See inside for Important Operating, Maintenance and Safety Instructions. Important Operating, Maintenance and Safety Instructions Carefully read all instructions before operating or servicing any Dynabrade® Abrasive Power Tool. Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration. Important: All Dynabrade rotary vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties. Operating Instructions: Warning: Eye, face, respiratory, sound, and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death. Follow safety procedures posted in workplace. 1. With power source disconnected from tool, securely fasten abrasive/accessory on tool. 2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid damaging valve body housing. 3. Connect power source to tool. Be careful not to depress throttle lever in the process. 4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be serviced to correct the cause before use. Maintenance Instructions: 1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to correct the cause before use. 2. Some silencers on air tools may clog with use. Clean and replace as required. 3. All Dynabrade rotary vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if the tool specification states 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt. 473 ml.) is recommended. 4. It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 11405 Air Line Filter-Regulator-Lubricator — Provides accurate air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components. Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports. 5. Use only genuine Dynabrade replacement parts. To reorder replacement parts, please specify the Model #, Serial # and RPM of your machine. 6. A Motor Tune-Up Kit (P/N 96045) is available which includes assorted parts to help maintain motor in peak operating condition. 7. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters, keytones, chlorinated hydrocarbons or nitro carbons. Safety Instructions: Products offered by Dynabrade should not be converted or otherwise altered from original design without expressed written consent from Dynabrade, Inc.

• Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI). • Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins. • Always disconnect power supply before changing abrasive/accessory or making machine adjustments. • Inspect abrasives/accessories for damage or defects prior to installation on tools. • Please refer to Dynabrade’s Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information. • Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration. Notice All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of this tool. One Year Warranty Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.

Models Motor Motor Sound Maximum Air Flow Air Pressure Spindle Weight Length Height HP (W) RPM Level CFM/SCFM (LPM) PSIG (Bars) Thread Pound (kg) Inch (mm) Inch (mm) All 15,000 RPM .7 (522) 15,000 85 dBA 4/32 (906) 90 (6.2) 3/8"-24 male 1.7 (.8) 6 (152) 5-1/2 (140) All 18,000 RPM .7 (522) 18,000 87 dBA 5/35 (991) 90 (6.2) 3/8"-24 male 1.7 (.8) 6 (152) 5-1/2 (140) All 20,000 RPM .7 (522) 20,000 84 dBA 5/36 (1,020) 90 (6.2) 3/8"-24 male 1.7 (.8) 6 (152) 5-1/2 (140) Additional Specifications: Air Inlet Thread 1/4" NPT • Hose Size 3/8" (10mm)

2 Disassembly/Assembly Instructions — .7Hp/7˚/Front Exhaust Die Grinder Please refer to page 1 for part identification. Important: Manufacturers warranty is void if tool is disassembled before warranty expires. To Disassemble: 1. Secure air tool in vise using 52996 Repair Collar or padded jaws. 2. Remove collet cap and insert. 3. With a 1-1/2" open-end wrench, remove exhaust cover by turning counter-clockwise. 4. Pull motor assembly from housing. 5. Reposition motor housing in vise so inlet bushing is facing upwards. 6. Unscrew 01494 Inlet Bushing turning counter-clockwise. 7. Using needle nose pliers, remove 01448 Spring, 01472 Tip Valve and 01464 Seal. 8. Resecure housing in vise so throttle lever and 12132 Pin are accessible. 9. Using a 2.5mm diameter drift pin and a hammer, tap 12132 Pin out from housing and remove throttle lever. 10. Remove 95558 Retaining Ring and push 01469 Speed Regulator from Housing. Optional: To disassemble valve body from motor housing, peel back 01558 Collar to expose 01461 Lock Nut. Unscrew lock nut/valve body from housing (left hand threads). Motor Disassembly: 1. Press rotor from 01743 Rear Bearing Plate. Press 02649 Bearing from bearing plate. 2. Remove 01008 Front Bearing Plate, cylinder, blades (4) and 01010 Spacer from rotor. Note: 01007 Bearing, 01008 Front Bearing Plate and 01010 Spacer are a slip fit onto rotor. 3. Remove 50011 Collet Body from rotor shaft by inserting 3/16" hex wrench through collet body into rotor shaft. Twist collet body from shaft. Motor Disassembly Complete. Motor Assembly: (Be sure parts are clean and in good repair before assembling.) 1. Place rotor in padded vise with threaded spindle facing upwards. 2. Slip 01010 Spacer onto rotor. 3. Place a .002" shim into 01008 Front Bearing Plate as an initial spacing (Note: 01121 Shim Pack contains .001" and .002" shims) and slip 01007 Bearing into plate. 4. Install Bearing/Bearing Plate assembly onto rotor. 5. Tighten collet body onto rotor (torque to 150 in. lbs.). 6. Check clearance between rotor and bearing plate by using a .001" feeler gauge. Clearance should be at .001" to .0015". Adjust clearance by repeating steps 1-5 with different shim if necessary. 7. Once proper rotor/gap clearance is achieved, install well lubricated 01185 Blades (4) into rotor slots. Dynabrade air lube P/N 95842 is recommended for lubrication. 8. Install cylinder over rotor. Be sure air inlet area of cylinder line up with air inlet holes in the rear bearing plate. 9. Press 02649 Rear Bearing into 01743 Rear Bearing Plate. Press bearing/bearing plate assembly onto rotor. Be sure that pin and air inlet holes line-up with pin slot and air inlet area in cylinder. Important: Fit must be snug between bearing plates and cylinder. If too tight, rotor will not turn freely. Rotor must then be lightly tapped at press fit end so it will turn freely while still maintaining a snug fit. A loose fit will not achieve the proper preload of motor bearings. 10. Secure motor housing in padded vise so motor cavity faces upwards. 11. Install motor assembly into housing. Be sure motor drops all the way into housing. 12. Insert 01744 Silencer into exhaust cover and install onto motor housing (torque 300 in. lbs.). 13. Motor adjustment must now be checked. With motor housing still mounted in vise, pull end of rotor and twist (10-15 lbs. force), rotor should turn freely without drag. If drag or rub is felt, then increase preload or remove shim. Also, push end of rotor and twist (10-15 lbs. force), rotor should turn freely without drag. If drag or rub is felt, then deload or add shim. Valve Stem/Body Assembly: 1. Insert 01469 Speed Regulator Assembly into valve body. Secure with 95558 Retaining Ring. 2. Secure valve body in vise using 52996 Repair Collar or padded jaws with air inlet facing upwards and throttle lever accessible. 3. Insert 01464 Seal into housing. 4. Line-up the hole in the 01449 Valve Stem with the hole in the housing (looking past brass bushing). Using needle nose pliers, insert 01472 Tip Valve so that the metal pin passes through the hole in the valve stem. 5. Install 01468 Spring (small end first). 6. Apply a small amount of #567 Loctite (or equivalent) to threads of 01494 Inlet Bushing and install into valve body (torque 34.0 N•m 300 lbs. in.). 7. Install throttle lever and 12132 Pin. Remove valve body from vise. Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool. Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should be serviced to correct the cause before use. Note: Throttle lever is preset at the factory at an 11:00 o’clock position. Loctite is a registered trademark of the Loctite Corp.

3 Optional Accessories

Dynaswivel® 96045 Motor Tune-Up Kit Swivels 360° at two locations which allows an • Includes assorted parts to help maintain air hose to drop straight to the floor, no matter and repair motor. how the tool is held. • 94300 1/4" NPT.

Collet Inserts 52296 Repair Collar • 50065 – 1/8" • Specially designed collar for use in vise to • 50013 – 1/4" prevent damage to valve body housing • 50014 – 3/8" during disassembly/assembly. • 50016 – 6 mm • 50039 – 8 mm

Open-End Wrenches Dynabrade Air Lube 95262 – 14mm open-end. • Formulated for pneumatic equipment. 95281 – 19mm open-end. • Absorbs up to 10% of its weight in water. • Prevents rust and formation of sludge. • Keeps pneumatic tools operating longer with greater power and less down time. 95842: 1 pt. (473 ml) 53163 Side Handle 95843: 1 gal. (3.8 L) • Improved ergonomic feel with grip-traction to reduce hand fatigue. • 5/16"-18 Thread

® Visit Our Web Site: www.dynabrade.com Email: [email protected] DYNABRADE

DYNABRADE, INC., 8989 Sheridan Drive • Clarence, New York 14031-1490 • Telephone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 71-231-2524 DYNABRADE EUROPE s.a.r.l., Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1 © DYNABRADE, INC., 2004 PRINTED IN USA PD02.19_Rev.1_03/04