Ceramic Chip Carrier

Total Page：16

File Type：pdf, Size：1020Kb

JEDEC Publication No. 95 INDEX BY DEVICE TYPE OF REGISTERED CARRIER OUTLINES (CO) FAMILY REGISTRATION NO. Ceramic Chip Carrier Magazine, Type A, B and D, 68 Pin Leadless CO-006 Ceramic Chip Carrier Coinstack TapePak® Magazine Family, Metal, Coinstack CO-019 Plastic Magazine Family, Coinstack CO-021 Plastic Magazine Plug Family CO-022 TapePak® Plug Family, Coinstack Magazine CO-023 Dual In-Line (DIP) 7.62mm .300 Row Spacing Magazine Family, (DIP), CO-001 TO-220 Magazine CO-002 7.62mm .300 Row Spacing Magazine Family, (DIP), CO-003 Square Magazine for (DIP) CO-004 7.62, 10.16, 15.24 mm Row Spacing Magazine (DIP), CO-005 Fine Pitch Plastic Shipping Tube Family Fine Pitch Plastic Shipping Tube Family. Item 11.5-233 CO-008 Flat Plastic Tube Sizes, Magazine MCR Plug Family, 36 mm, 46 mm and 56 mm Flat Plastic CO-025 Tube Sizes, Magazine MCR Tube Family, 36 mm, 46 mm and 56 mm Flat Plastic CO-026 Tube Sizes, Magazine Generic Carrier Family Generic Carrier Family CO-013 2 inch Leaded Quadpack Carrier CO-014 Low Profile Matrix Tray for Thin Microelectronic Devices Low Profile Matrix Tray for Shipping and Handling CO-034 Thin Microelectronic Devices i Updated 10/05 JEDEC Publication No. 95 INDEX BY DEVICE TYPE OF REGISTERED CARRIER OUTLINES (CO) FAMILY REGISTRATION NO. Mini Tray Thin Matrix Mini Tray for Shipping and Handling CO-030 Mini Tray (cont’d) Thick Matrix Mini Tray for Shipping and Handling CO-031 Thin Matrix Tray for Shipping and Handling SOJ CO-032 Pin Grid Array Package Pin Grid Array Package D132 Carrier Family, .100 inch Centers CO-007 PLCC Tray for Shipping and Handling PLCC Tray for Handling and Shipping CO-016 PLCC Shipping Tube Family Plastic Chip Carrier Shipping Tube CO-033 Tape Automated Bonding (TAB) Tape Carrier Family Tape Automated Bonding (TAB) Tape Carrier Family, CO-009 35, 48, 70 mm Metric Tape Automated Bonding (TAB) Magazine Family, CO-017 Replaced - See CS-001 50, 100 Leads, Metric Tape Automated Bonding (TAB) Tape Carrier Family, CO-018 Replaced - See CS-006-A Tray for Shipping and Handling of PGA Packages Tray for Handling and Shipping of PGA Packages CO-010 Tray for Shipping and Handling of Quad Flatpack Package (QFP) Ceramic Quad Flatpack Package (CQFP) CO-011 Tray for Handling and Shipping Metric Quad Flatpack Packages (MQFP) CO-012 Tray for Handling and Shipping Tray for Handling and Shipping of (PQFP) CO-015 Packages, 52, 68, 84, 100, 132, 164, 196 and 244 Pins 249 Updated 10/05 ii .

Copy Link

Recommended publications

Ceramic Leadless Chip Carrier (LCC)
Ceramic,Leadless,Chip,Carrier,(L Ceramic Leadless Chip Carrier (LCC) Literature Number: SNOA023 Ceramic Leadless Chip Carrier (LCC) August 1999 Ceramic Leadless Chip Carrier (LCC) 20 Lead Ceramic Leadless Chip Carrier, Type C NS Package Number E20A © 2000 National Semiconductor Corporation MS101105 www.national.com 20 Lead Ceramic Leadless Chip Carrier NS Package Number EA20B Ceramic Leadless Chip Carrier (LCC) www.national.com 2 Ceramic Leadless Chip Carrier (LCC) 24 Lead Ceramic Leadless Chip Carrier NS Package Number E24B 28 Lead Ceramic Leadless Chip Carrier, Type C NS Package Number E28A 3 www.national.com 28 Lead Ceramic Leadless Chip Carrier, Dual Cavity NS Package Number EA028C Ceramic Leadless Chip Carrier (LCC) www.national.com 4 Ceramic Leadless Chip Carrier (LCC) 32 Lead Ceramic Leadless Chip Carrier, Type C NS Package Number E32A 32 Lead Ceramic Leadless Chip Carrier, Type C NS Package Number E32B 5 www.national.com 32 Lead Ceramic Leadless Chip Carrier, Type C NS Package Number E32C Ceramic Leadless Chip Carrier (LCC) 32 Lead Ceramic Leadless Chip Carrier, Type E NS Package Number EA32B www.national.com 6 Ceramic Leadless Chip Carrier (LCC) 32 Lead Ceramic Leadless Chip Carrier, DIP NS Package Number EA32C 40 Lead Ceramic Leadless Chip Carrier, Type C NS Package Number E40A 7 www.national.com 44 Lead Ceramic Leadless Chip Carrier, Type C NS Package Number E44A Ceramic Leadless Chip Carrier (LCC) 48 Lead Ceramic Leadless Chip Carrier NS Package Number EA48B www.national.com 8 Ceramic Leadless Chip Carrier (LCC) 68 Lead Ceramic
[Show full text]
PDF Package Information
This version: Apr. 2001 Previous version: Jun. 1997 PACKAGE INFORMATION 1. PACKAGE CLASSIFICATIONS This document is Chapter 1 of the package information document consisting of 8 chapters in total. PACKAGE INFORMATION 1. PACKAGE CLASSIFICATIONS 1. PACKAGE CLASSIFICATIONS 1.1 Packaging Trends In recent years, marked advances have been made in the electronics field. One such advance has been the progression from vacuum tubes to transistors and finally, to ICs. ICs themselves have been more highly integrated into LSIs, VLSIs, and now, ULSIs. With increased functions and pin counts, IC packages have had to change significantly in the last few years in order to keep-up with the advancement in semiconductor development. Functions required for conventional IC packages are as follows: 1) To protect IC chips from the external environment 2) To facilitate the packaging and handling of IC chips 3) To dissipate heat generated by IC chips 4) To protect the electrical characteristics of the IC Standard dual-in-line packages (DIP), which fulfill these basic requirements, have enjoyed wide usage in the electronics industry for a number of years. With increasing integration and higher speed ICs, and with the miniaturization of electronic equipment, newer packages have been requested by the industry which incorporate the functions listed below: 1) Multi-pin I/O 2) Ultra-miniature packages 3) Packages suited to high density ICs 4) Improved heat resistance for use with reflow soldering techniques 5) High throughput speed 6) Improved heat dissipation 7) Lower cost per pin In response to these requests, OKI has developed a diversified family of packages to meet the myriad requirements of today’s burgeoning electronics industry.
[Show full text]
Quad Flat No-Lead (QFN) Evauation Test
National Aeronautics and Space Administration Quad Flat No-Lead (QFN) Evaluation Testing Reza Ghaffarian, Ph.D. Jet Propulsion Laboratory Pasadena, California Jet Propulsion Laboratory California Institute of Technology Pasadena, California 6/17 National Aeronautics and Space Administration Quad Flat No-Lead (QFN) Evaluation Testing NASA Electronic Parts and Packaging (NEPP) Program Office of Safety and Mission Success Reza Ghaffarian, Ph.D. Jet Propulsion Laboratory Pasadena, California NASA WBS: 724297.40.43 JPL Project Number: 104593 Task Number: 40.49.02.35 Jet Propulsion Laboratory 4800 Oak Grove Drive Pasadena, CA 91109 http://nepp.nasa.gov 6/17 This research was carried out at the Jet Propulsion Laboratory, California Institute of Technology, and was sponsored by the National Aeronautics and Space Administration Electronic Parts and Packaging (NEPP) Program. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise, does not constitute or imply its endorsement by the United States Government or the Jet Propulsion Laboratory, California Institute of Technology. Copyright 2017. California Institute of Technology. Government sponsorship acknowledged. Acknowledgments The author would like to acknowledge many people from industry and the Jet Propulsion Laboratory (JPL) who were critical to the progress of this activity including the Rochester Institute of Technology (RIT). The author extends his appreciation to program managers of the National Aeronautics and Space
[Show full text]
Building Your Prototype
Building Your Prototype Prototype Construction Techniques Part Numbers Package Types Specification Sheets Schematic Diagrams Practical Advice T. Grotjohn, [email protected] Prototype Construction Techniques 1) Protoboard Use DIP components Keep your wires neat and color coded Prone to bad connections Maximum operating speed: ~ few MHz 2) Wire Wrap Often done using wire wrap sockets on a vector board Use DIP components Wire used is good for digital signals Be careful with high current lines because the wire is small. Typical wire: 30 gauge 0.34 Ω/m 28 gauge 0.21 Ω/m 3) Soldered Board Single solder points board Tied solder points board (Your mini project #1) PCB: printed circuit board PCB can be made for ECE 480 projects in the ECE Shop: See the shop’s web page. (Also see the next page) . Printed Circuit Board System General Information T-Tech Protyping Machine ECE 482 Student Project Design Department of Electrical and Computer Engineering, 1999 Michigan State University, East Lansing, Michigan, USA Part Numbers Typical Part Number: DM8095N Prefix: Indicates the manufacture of the part. See two pages in Attachment 1. Suffixes: Indicates temperature range: “military”, “industrial”, “commercial” Also the suffixes are used to indicate package types. The ECE shop deals most often with the following electronic part suppliers. Allied Electronics (www.alliedelec.com) Digi Key (www.digikey.com) Newark Electronics (www.newark.com) For other (non-electronic) supplies, suppliers often used are Grainger (www.grainger.com) McMaster Carr (www.mcmaster.com) Package Types DIP: Dual Inline Package Easiest to use. Works in protoboards, solder boards, wire wrapping, easiest to solder components to PCB This is your choice for ECE 480.
[Show full text]
Packaging Product Specification
Packaging Product Specification PS007225-0607 Copyright ©2007 by ZiLOG, Inc. All rights reserved. www.zilog.com DO NOT USE IN LIFE SUPPORT Warning: LIFE SUPPORT POLICY ZiLOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF ZiLOG CORPORATION. As used herein Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Document Disclaimer ©2007 by ZiLOG, Inc. All rights reserved. Information in this publication concerning the devices, applications, or technology described is intended to suggest possible uses and may be superseded. ZiLOG, INC. DOES NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZiLOG ALSO DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED HEREIN OR OTHERWISE. The information contained within this document has been verified according to the general principles of electrical and mechanical engineering. Z8, Z8 Encore!, Z8 Encore! XP, Z8 Encore! MC, Crimzon, eZ80, and ZNEO are trademarks or registered trademarks of ZiLOG, Inc.
[Show full text]
Package Reliability As Affected by Material and Processes
I,, '• Package Reliability as Affected By Materials and Processes The semiconductor industry is faced with the problem of how to increase the level of reliability of semiconductor parts being used in electronic systems which have had their lifetimes extended through new and.better system designs. By David Nixen, cussed, are all commercially availc1ble and presently The Aerospace Corporation, being used in high volume in industry. It is not the El Segundo, California intention of this article to present any new, revolu tionary packaging approach, but rather to compare the advantages and disadvantages of the major types The word "reliability" has been used in the semicon as they relate to reliability. uuctor industry over the years in every imaginable The actual choice of which package to use will not way. It may refer to why the cost is so high, the be presented here since that choice is too highly delivery so late, the documentation so voluminous, dependent upon the unique conditions of each indi or, it may be why the system is successful. When vidual case. discussed in the true sense of the word, perhaps reliability has no greater importance than in aero PACKAGE FAMILIES ,, , space systems. The basic package families are divided into three Until this year, a spacecraft system had a projected groups; these three groups, in turn, can be subdivid life of three to five years. Since an orbiting system ed and they, in turn, can also be subdivided. Only cannot be considered in a "repair/replace" categoryr the major families will be discussed, although some a component was required to have an extremely high of the subdivisions will be acknowledged.
[Show full text]
LM117/LM317A/LM317 3-Terminal Adjustable Regulator
LM117/LM317A/LM317 3-Terminal Adjustable Regulator July 2004 LM117/LM317A/LM317 3-Terminal Adjustable Regulator General Description age, supplies of several hundred volts can be regulated as long as the maximum input to output differential is not ex- The LM117 series of adjustable 3-terminal positive voltage ceeded, i.e., avoid short-circuiting the output. regulators is capable of supplying in excess of 1.5A over a Also, it makes an especially simple adjustable switching 1.2V to 37V output range. They are exceptionally easy to regulator, a programmable output regulator, or by connecting use and require only two external resistors to set the output a fixed resistor between the adjustment pin and output, the voltage. Further, both line and load regulation are better than LM117 can be used as a precision current regulator. Sup- standard fixed regulators. Also, the LM117 is packaged in plies with electronic shutdown can be achieved by clamping standard transistor packages which are easily mounted and the adjustment terminal to ground which programs the out- handled. put to 1.2V where most loads draw little current. In addition to higher performance than fixed regulators, the For applications requiring greater output current, see LM150 LM117 series offers full overload protection available only in series (3A) and LM138 series (5A) data sheets. For the IC’s. Included on the chip are current limit, thermal overload negative complement, see LM137 series data sheet. protection and safe area protection. All overload protection circuitry remains fully functional even if the adjustment ter- minal is disconnected. Features Normally, no capacitors are needed unless the device is n Guaranteed 1% output voltage tolerance (LM317A) situated more than 6 inches from the input filter capacitors in n Guaranteed max.
[Show full text]
An Introduction to Plastic Pin Grid Array (PPGA) Packaging
E AP-577 APPLICATION NOTE An Introduction to Plastic Pin Grid Array (PPGA) Packaging April 1996 Order Number: 243103-001 7/1/96 9:08 AM 243103_1.doc Information in this document is provided in connection with Intel products. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel’s Terms and Conditions of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Intel products are not intended for use in medical, life saving, or life sustaining applications. Intel retains the right to make changes to specifications and product descriptions at any time, without notice. The Pentium® processor may contain design defects or errors known as errata. Current characterized errata are available on request. *Third-party brands and names are the property of their respective owners. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an ordering number and are referenced in this document, or other Intel literature, may be obtained from: Intel Corporation P.O. Box 7641 Mt. Prospect, IL 60056-7641 or call 1-800-879-4683 COPYRIGHT © INTEL CORPORATION 1996 7/1/96 9:08 AM 243103_1.doc AP-577 CONTENTS PAGE PAGE 1.0. INTRODUCTION................................................5 4.0.
[Show full text]
Package Information Datasheet for Mature Altera Devices
Package Information Datasheet for Mature Altera Devices DS-PKG-16.8 This datasheet provides package and thermal resistance information for mature Altera® devices. Package information includes the ordering code reference, package acronym, leadframe material, lead finish (plating), JEDEC outline reference, lead coplanarity, weight, moisture sensitivity level, and other special information. The thermal resistance information includes device pin count, package name, and resistance values. This datasheet includes the following sections: ■ “Device and Package Cross Reference” on page 1 ■ “Thermal Resistance” on page 23 ■ “Package Outlines” on page 44 f For more package and thermal resistance information about Altera devices that are not listed in this datasheet, refer to the Package and Thermal Resistance page of the Altera website. f For information about trays, tubes, and dry packs, refer to AN 71: Guidelines for Handling J-Lead, QFP, and BGA Devices. f RoHS-compliant devices are compatible with leaded-reflow temperatures. For more information, refer to Altera’s RoHS-Compliant Devices literature page. Device and Package Cross Reference Table 2 through Table 22 lists the device, package type, and number of pins for each Altera device listed in this datasheet. Altera devices listed in this datasheet are available in the following packages: ■ Ball-Grid Array (BGA) ■ Ceramic Pin-Grid Array (PGA) ■ FineLine BGA (FBGA) ■ Hybrid FineLine BGA (HBGA) ■ Plastic Dual In-Line Package (PDIP) ■ Plastic Enhanced Quad Flat Pack (EQFP) ■ Plastic J-Lead Chip Carrier (PLCC) ■ Plastic Quad Flat Pack (PQFP) ■ Power Quad Flat Pack (RQFP) ■ Thin Quad Flat Pack (TQFP) ■ Ultra FineLine BGA (UBGA) © December 2011 Altera Corporation Package Information Datasheet for Mature Altera Devices 2 Package Information Datasheet for Mature Altera Devices Device and Package Cross Reference Table 1 lists the Altera devices and the associated table locations.
[Show full text]
NUREG/CR-7006 "Review Guidelines for Field-Programmable Gate Arrays in Nuclear Power Plant Safety Systems."
NUREG/CR-7006 *U.S.NRC ORNL/TM-2009/20 United States Nuclear Regulatory Commission ProtectingPeople and the Environment Review Guidelines for Field-Programmable Gate Arrays in Nuclear Power Plant Safety Systems Office of Nuclear Regulatory Research AVAILABILITY OF REFERENCE MATERIALS IN NRC PUBLICATIONS NRC Reference Material Non-NRC Reference Material As of November 1999, you may electronically access Documents available from public and special technical NUREG-series publications and other NRC records at libraries include all open literature items, such as NRC's Public Electronic Reading Room at books, journal articles, and transactions, Federal http://www.nrc.gov/reading-rm.html. Publicly released Register notices, Federal and State legislation, and records include, to name a few, NUREG-series congressional reports. Such documents as theses, publications; Federal Register notices; applicant, dissertations, foreign reports and translations, and licensee' and vendor documents and correspondence; non-NRC conference proceedings may be purchased NRC correspondence and internal memoranda; from their sponsoring organization. bulletins and information notices; inspection and investigative reports; licensee event reports; and Copies of industry codes and standards used in a Commission papers and their attachments. substantive manner in the NRC regulatory process are maintained at- NRC publications in the NUREG series, NRC The NRC Technical Library regulations, and Title 10, Energy, in the Code of Two White Flint North Federal Regulations may also be purchased from one 11545 Rockville Pike of these two sources. Rockville, MD 20852-2738 1. The Superintendent of Documents U.S. Government Printing Office These standards are available in the library for Mail Stop SSOP reference use by the public.
[Show full text]
Package Information
PACKAGE INFORMATION Package Thermal Characteristics This document provides test information about the has one site, with minimal exposed copper area. standard packages offered by Allegro MicroSystems. Where two values are shown in this column, it in- The data given is intended as a general reference only dicates that the printed circuit board has multiple and is based on certain simplifications such as con- sites, each having a different amount of exposed stant chip size and standard bonding methods. copper foil. The ground leads (power tabs) of the devices are connected to these areas of copper To use this document, in the Allegro Package Code foil. The two results shown indicate the highest column, locate the package designator for the device. and the lowest test results. To locate package variants, use the JEDEC Package Note that the paired results are text hyperlinks to Outline column to locate the corresponding JEDEC other Web pages. Click the text to open the linked designator, or use the Quantity and Type of Terminals page, which provides information on the test and column to locate the variant by the configuration of printer circuit board layout, as well as intermedi- terminals. ate test results. Three columns of results are presented: • R , R , R . This column provides results θJC θJP θJT on other thermal dissipation paths: • RθJA High K. This test is performed using a high thermal conductivity, mutlilayer printed circuit RθJC [c] Through the device case. board that closely approximates those specified RθJP [p] Through the exposed thermal pad see in JEDEC standard JEDEC51-7 (surface-mount Application Note 26020, Procedure for Mea- devices), JEDEC51-5 (for exposed thermal suring Pad-to-Ambient Thermal Resistance pads), or JEDEC51-10 (through-hole devices).
[Show full text]
Lm317mdt/Nopb
Distributed by: www.Jameco.com ✦ 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM117/LM317A/LM317 3-Terminal Adjustable Regulator June 2006 LM117/LM317A/LM317 3-Terminal Adjustable Regulator General Description age, supplies of several hundred volts can be regulated as long as the maximum input to output differential is not ex- The LM117 series of adjustable 3-terminal positive voltage ceeded, i.e., avoid short-circuiting the output. regulators is capable of supplying in excess of 1.5A over a Also, it makes an especially simple adjustable switching 1.2V to 37V output range. They are exceptionally easy to regulator, a programmable output regulator, or by connecting use and require only two external resistors to set the output a fixed resistor between the adjustment pin and output, the voltage. Further, both line and load regulation are better than LM117 can be used as a precision current regulator. Sup- standard fixed regulators. Also, the LM117 is packaged in plies with electronic shutdown can be achieved by clamping standard transistor packages which are easily mounted and the adjustment terminal to ground which programs the out- handled. put to 1.2V where most loads draw little current. In addition to higher performance than fixed regulators, the For applications requiring greater output current, see LM150 LM117 series offers full overload protection available only in series (3A) and LM138 series (5A) data sheets. For the IC’s. Included on the chip are current limit, thermal overload negative complement, see LM137 series data sheet. protection and safe area protection.
[Show full text]