Drill holes to appropriate position in the fairing of the cowl 73 and epoxy the wood dowel in them. 76 Adjustment.

Plastic tube (3x30mm) Fieseler Fi 156 Storch 3mm RUDDER 25mm

25mm 11mm 25mm

Plastic tube (3x30mm) Top view Side View 2

Drill holes to the relevant position in the cowl and epoxy the Adjustment. 74 cowl fairing to the cowl as below. 77

Side View AILERON 20mm 20mm FLAP

30mm 25mm 3mm Top View

AILERON FLAP Specification:

Adjustment. Centre of Gravity. Length :1614 mm(63.5") 75 78 Wing Span :2362 mm(93") Wing Area :61.68 sq. dm 6.64 sq. ft Wing Loading :116.7 g/sq. dm 38.3 oz/sq. ft ELEVATOR Flying Weight :7.2 kg(15.8 lbs) Top view Radio :6ch&7servos INSTRUCTION MANUAL Engine :120 4-cycle 25mm 25mm Side View This R/C airplane is not a toy! Position for 90mm (The people under 18 years old is forbidden from flying this model) right diagram. First-time builders should seek advice from people having building experience.If misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. SAFETY PRECAUTIONS We suggest having a qualified instructor carefully inspect your airplane before its first flight.Please carefully read and follow all instructions included with this airplane,your radio control system 14 and any other components purchased separately. Glue the trimed PVC parts to the relevant position Trim small holes to relevant position in the cockpit for 67 in the fuselage one by one carefully with CA glue. 70 fixing the wings. Screw Driver

6 7

6

6 channel radio for aiplane is highly recommended for this model.

6

Trim holes in the cowl for the engine muffler. 68 Assemble the cockpit to the fuselage with screw. 71 Assemble the cowling.

1.5mm

4-cycle .120

TP Screw (2.3x8mm) Optional parts: rubber wheel with metal hub. 9 TP Screw (2.3x8mm) 5

Spinner nut Epoxy plies inside the fuselage under the cowing and mount the cowing with TP screw as illustration. 15″X7

Assemble the wing to the fuselage until it get to the right Trim this PVC parts carefully along the shaded line and glue 69 position as the referent illustration below. 72 it to appropriate position on the fuselage as illustration.

A A’ B B' 75mm

A=A' B =B'

We strongly recommen you use the thread lock for all the screws when you build your model.

13 62 Assemble the servo to fuselage. Accessory list for the coming installation steps. Accessory list for the coming installation steps. 3 Assemble the metal plates to the strut B. metal plate 4 Strut B PVC Oleo strut Lock Nut (3mm ) 1 1 PVC 1 2 1 Strut A Collar (3mm) PVC 1 2 1 PVC 1 Screw (3x15mm) Strut B 8 PVC 1 Washer (3x6mm) 1 TP Screw (2.3x8mm) 5 8 PVC metal plate Wheel (90mm) Strut B 1 Plastic tube (3x30mm) 2 4 2 Collar (5mm) fibre gear covering 1 PVC Fairing of the cowl 2 2 1 fibre gear covering Bushing (7X8mm) PVC 2 2 metal plate 1 Wooden Block (12mm Ply) Wooden Block (12mm Ply) 2 2

Install the rudder servo and the elevator servo. Cut the PVC parts off carefully along the shaded line. The front view when the landing gear assembled Assemble the metal plates to appropriate position in the 63 65 1 completion. 4 fuselage with screws. Screw (2x10mm) Screw (3x15mm) 8 Ball joint A=A’ Washer (3x6mm) Nut (2mm ) B B’ B=B’ 8 Aluminum tube Copper joiner

Screw (3x15mm) Steel wire

Clevis 6 Copper joiner 6 Aluminum tube(3x6mm) 6 Screw (2x10mm) A A’ 6 Nut (2mm ) 6

The sketch map when the sevos install completion. Glue the trimed PVC parts to relevant position in the Fix the strut A to appropriate position in the fuselage Fix the other side of the strut B to the oleo 64 Mounting of the receiver and the battery. 66 cockpit one by one with CA glue. 2 and the oleo struts tightly as illustration. 5 strut as illustration. Washer(3x6mm) Strut A 1 2 Lock Nut (3mm ) 2 Collar (3mm) 2 Elevator servo

Screw Driver Collar Throttle servo

4X5mm Washer(3x6mm) Rudder servo Lock Nut (3mm ) 4X5mm

12 1 Detach the eleo strut first with screw driver,let the detached Assemble the wheel to the oleo strut. oleo strut pass through the fibre gear covering,epoxy them Assemble the engine. Assembly of the fuel tank. 6 9 and combine the two parts of the oleo strut again. 56 59

Screw (4x35mm) 90mm Screw Driver Collar (5mm) Washer (4x8mm)

Bushing (7X8mm) Bushing (7X8mm) 4mm

Screw (4x25mm)

Washer (4x8mm) Air pressure line Spring Washer (4mm) Fuel spray line

Nut (4mm) Fuel supply line Washer (4x8mm)

Put the oleo strut into the fixed wing mounting's 7 slot and fix it with locknut as illustrate. Accessory list for the coming installation steps. 57 Assemble the throttle linkage. 60 Mount the fuel tank into the fuselage. Screw Driver Fiberboard A (2mm) Set Screw (3x4mm) Linkage Stopper 14 1 Fiberboard B (2mm) 24 Fiberboard C (2mm) Washer (2mm) 8 1 Fiber fairing (2mm) Washer (4x8mm) 4 Rod (2x450mm) 4 TP Screw (2.3x12mm) 16 Set Screw (2mm) Nut (2mm ) 1 16 Screw (2x10mm) Set Screw (3x4mm) D 16 Washer (2x5mm) 16 Screw (4x25mm) Copper dowel (3x7mm) 4 12 Clevis 4 Set Screw (2mm) Blind Nut (4mm) Fiber arm (2mm ) 4 4 Fuel tank (550cc) Fiber board mount (2mm ) Rod (2x450mm) 1 4 1

Brush the edge of fibre gear covering and epoxy the Glue the Fiberboard A to the lefting aileron with CA glue. Install the engine. Assemble the servos and switch . 8 wooden block to it. 10 58 61 Fiberboard (2mm) 14 Set screw (3x4mm)

Washer (2mm) Washer (2mm)

Linkage Stopper 1 fibre gear covering Washer (2mm) 2 1 fibre gear covering 2 Nut (2mm) Wooden Block (12mm Ply) 1 2 Wooden Block (12mm Ply) Set screw (3x4mm) 2 1

2 11 Accessory list for the coming installation steps.

Assemble the tail wheel tray to fuselage and the The front view of the engine install completion. Glue the lefting ailerong to the wing by fiberboard A Connect the fiberboard B and fiberboard C with 51 wheel to tail undercarriage. 53 11 with CA glue. 14 screw and nut as illustration. Nut (2mm ) TP Screw (2.3x12mm) Collar Washer (2x5mm) 6 Screw (2x10mm) Screw (2x10mm) Washer (2x5mm) 6 Washer (2x5mm) 6 Copper dowel (3x7mm) 6 Copper dowel (3x7mm) Nut (2mm )

1.5mm

TP Screw (2.3x12mm) Make sure hinges are 4 In case of 2-cycle & 4-cycle engine. mounted in the same line.

Assemble the stabilizer strut by TP serew. The side view of the engine install completion. Trim the fiber fairings and glue them fiberboard C to 52 54 12 Glue the fiberboard C to the flap with CA glue. 15 relevant slot in the aileron. Marked dot Screw (3x10mm) Fiberboard (2mm) Fiberboard (2mm) Fiber fairing (2mm) 6

1.8mm 155 mm 3mm Marked dot Fiberboard (2mm)

Washer (3x6mm )

Marked dot 1.8mm 3mm Screw (3x10mm) Fiberboard (2mm) 4 Marked dot 2 Washer (3x6mm ) 4 Fiber fairing (2mm) Stab strut 1 4

Drill four holes at the diameters as shown Glue the fiberboard B to the relevant slots in the wings. Accessory list for the coming installation steps. 55 for engine mount. 13 Glue the fiberboard B to the relevant slot in the wing. 16 Fiberboard (2mm) Fiberboard (2mm) Fiberboard (2mm) 12 12 Blind Nut (4mm) Plastic tube (2x450mm) 3mm 4 1 Screw (4x35mm) Engine mount (68x105mm) 4 2 Screw (4x25mm) Center line 4 Clevis 3mm Marked dot Washer(4x8mm) 6 12 Copper joiner 5.2mm Spring Washer (4mm) 6 4 Screw (2x10mm) 6 Marked dot Nut (4mm) Nut (2mm ) Blind Nut 4 6 70mm Linkage Stopper Washer(2x5mm) Fiberboard (2mm) 2 6 Fuel tank (550cc) Aluminum tube(3x6mm) 1 6 Blind Nut (4mm) 4

10 3 Keep some space about 1mm width between Connect the fiberboard B and fiber fairing with screw Epoxy the fiber arm to the slot in the fiber board mount. The sketch map after the rudder shaft assemble finished. 17 and nut as illustration. 20 45 the tailing edge and the rudder. 48 Nut (2mm ) Lock Nut (2mm ) 6 Washer (2x5mm) Washer(2x5mm) Screw (2x10mm) Screw (2x10mm) 6 Washer (2x5mm) Tailing Washer (2x5mm) Copper ball (2mm ) edge 6 Fiber arm (2mm ) Copper dowel (3x7mm) 6 Copper dowel (3x7mm) Nut (2mm ) Cut away the rubber tube when Screw (2x10mm) the epoxy glue dried. Steel wire Rudder

Lock Nut (3mm ) Clevis

Fiber board mount (2mm ) 1mm Aluminum tube Washer(3x15mm) Clevis Screw (3x80mm) 4 Fiber arm (2mm ) Clevis Screw (2x10mm) 4 2 Screw (3x80mm) 1 4 Copper joiner Nut (2mm ) Make sure they are in Washer(3x15mm) 2 Make sure hinges are 4 Fiber board mount (2mm ) 2 Washer(2x5mm) 4 the right position while Lock Nut (3mm ) Steel wire (0.5x1200mm) mounted in the same line. 4 installing. 2 2

Assemble the fiber board mount to appropriate position Drill hols to appropriate position in the vertical tail Install the servo as the illustration below The sketch map of the linkage for the rudder 18 21 in the aileron with TP screw and epoxy. 46 and epoxy the rudder to the vertical tail steadily. 49 and the tail gear. TP Screw (2.3x12mm)

1.5mm

TP Screw (2.3x12mm) 2.5mm

TP Screw (2.3x12mm) 8

Drill a hole to appropriate position in the Install the nylon control horn and connect the linkage. Secure the servo,connect the linkage of the servo 19 22 and the fiber arm. 47 rudder as illustration. 50 The sketch map of the linkages in the fuselage. TP Screw (2.3x12mm) TP Screw (2.3x12mm) 16 Retainer Rod (2x300mm) 1.5mm Elevator wire

1.5mm 3mm Ball joint Tail wheel wire 15mm Rudder wire

4 9 Blind Nut (4mm) Clevis 1 4 Retainer Screw (4x35mm) 1 4 Screw (3x35mm) 1 Screw (4x25mm) Washer(3x15mm) 4 1 Washer(4x8mm) Lock Nut (3mm ) 12 1 Washer(3x15mm) Spring Washer (4mm) 1 4 Clevis 2 Nut (4mm) Copper joiner 4 2 Screw (2x10mm) 2 Linkage Stopper 2 Nut (2mm ) 2 Washer(2x5mm) Plastic tube (2x500mm) 2 1 Clevis Engine mount (68x105mm) 1 2 Fiberglass pushrod(3x775mm) 2 Fuel tank (550cc) Steel wire (0.5x1500mm) 1 2 Plastic tube(3x50mm) TP Screw (2.3x12mm) 2 4 Ply (15x15x3mm) 4

40

Steel wire (0.5x3000mm) 2

Assemble the wheel steeling mounts to relevant Keep some space about 1mm width between the Accessory list for the coming installation steps. Epoxy the positioning pin and the wing joiner to 39 elevator and horizontal tail edge. 42 position in the former of tail gear. 25 the wing tightly.. Washer (3x6mm) Trailing 4 35mm edge TP Screw(3x20mm) 4 Fiber main wing joiner(6mm) Strut wire 1 1 Positioning pin (3x90mm) TP Screw (2x15mm) 8 Elevator 2 Rib template (2mm ply) Landing gear straps TP Screw(3x20mm) 1 4 Washer (2x5mm ) 16 Wing strut Nut (2mm ) 1 8 1mm Screw (3x20mm) Screw (3x15mm) 4 2 Screw (3x25mm) Washer(3x6mm) 2 8 Make sure they are in Take care not let the tube Fiber main wing joiner(6mm) the right position while 1 installing. touch the arm .

The sketch map when tail wheel assemble completion. Glue the elevator to the stabilizer by CA and epoxy. The sketch map after the wings assembly completion. According to the rib template open a slot in the cockpit 40 43 23 26 as illustration for draging the servo lines.. Make sure to glue securely. Accessory list for the coming installation steps. Cut off the suplus parts of the tube for If not properly glued, a failure in flight may occur. fit the arm well. Securely glue together.If coming off during flights, you'll lose control of your airplane which leads to accidents! 3mm Nose arm(3mm) 1 Temporarily fasten down the main wing and Tail landing gear(3mm) check its correct position. Washer (3x6mm) 1 4 The surface of the top wings should be in one plan. TP Screw(3x20mm) 4 Tail wheel (45mm) 1 Collar (3mm) A A‘ 3 Steel wire (0.5x3000mm) 4 Rib template (2mm ply) Screw (3x80mm) 1 Clevis B A=A' B‘ 2 Securely glue together. If coming off during flights, you 'll B=B ' Washer(3x15mm) 2 lose control of your airplane which leads to accidents! Lock Nut (3mm ) 2 Copper joiner 2 The sketch map when assemble the tail landing Assemble the wing to the fixed wing mount until it fit TP Screw (2.3x12mm) Epoxy pin hinges to rudder. According to the rib template drill a hole to appropiate very well and mark in the main wing joiner through 4 41 gear to the wheel steeling mount. 44 24 position in the wing root. 27 the hole in the mount with red mark. Positioning pin (3x90mm) 2 Rib template (2mm ply) 1 2.5mm Tail landing gear Collar 55mm 3mm Collar 40mm 55mm Positioning pin (3x90mm)

Rib template (2mm ply)

Collar Pin hinge Make sure hinges are 3 mounted in the same line.

8 5 Find out the blind nut position in the fuselage and wing,fix one side of wing strut on the fuselage,keep the wing in water surface and drill holes Assemble the wing strut to the fuselage and wing again Epoxy the horizontal tail to fuselage.Remove paint Drill a hole to the marked dot in the main wing joiner. to appropriate position in the strut for fitting the strut to the relevant blind and fix the strut wire with screw and nut as illustration. at fuselage horizontal mating surfaces before epoxy. 28 31 nut very well. 34 36 Screw (3x25mm) Screw (2x15mm) Stab joiner (16x250mm) Blind Nut 2 1 Screw (3x25mm) Washer (3x6mm ) Washer (2x5mm) 2

Washer(3x6mm)

Washer (2x5mm) Marked dot Nut (2mm ) 3mm

Marked dot Washer (2x5mm ) Marked dot 16 Nut (2mm ) 8 TP Screw (2x15mm) 3mm 8 Marked dot Landing gear straps 4 According to the rib template drill holes in the stabilizer and fuselage!

Fitting the wing to the fixed wing mounting and it Accessory list for the coming installation steps. Trim slot to appropriate position in the edge of stabilizer 29 will be demounted after step 30. 32 Assemble the wing strut to the fuselage and wing very well. 37 for assembling the U-style wire and arm.

Screw (3x15mm) Stab joiner (16x250mm) Steel wire (0.5x1500mm) 1 2 Pin hinge(24x24mm) Steel wire (0.5x3000mm) 4 4 Washer(3x6mm) U-style wire (3mm) Screw (3x80mm) 1 2x20mm 1 Clevis Pin hinge(2.5x48mm) 2 3 Washer(3x15mm) Blind Nut 2 Nose arm(3mm) 1 Lock Nut (3mm ) 2 Tail landing gear(3mm) Copper joiner 1 2 Washer (3x6mm) 4 TP Screw (2.3x12mm) 4 Tail wheel (45mm) 1 TP Screw(3x20mm) 4 Collar (3mm) Screw (3x10mm) 3 4 Steel wire (0.5x3000mm) Screw (3x15mm) Stab strut Washer(3x6mm) 2 4 1 4 U-style wire (3mm) Washer (3x6mm ) 1 4

Inset the strut wire to the slot in the wing,move the other side of the strut Fitting the cockpit to the fuselage with screw and it wire until it touch the wing strut very well,make marked dot in the wing The sketch map after the horizontal tail assembly Glue the pin hinge to the elevator with CA glue and trim will be demounted with screw driver after this step. strut though the hole in the gear straps.Demount the wing strut and drill completion. slot to appropriate position as illustration. 30 33 holes in relevant position. 35 38 Screw (3x20mm) Make sure to glue securely. 2 If not properly glued, a failure in flight may occur. Washer (3x6mm) Securely glue together.If coming off during flights, 2 you'll lose control of your airplane which leads to accidents! 2mm Temporarily fasten down the main wing and check its correct position. Marked dot

A A’ Landing gear straps B B' 3mm

Washer (3x6mm) A=A' Pin hinge(24x24mm) Screw (3x20mm) B =B' 4

6 7