DOCSLIB.ORG

A Deep Dive Into Kinetic Energy Recovery Systems – Part 1

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
A Deep Dive Into Kinetic Energy Recovery Systems – Part 1 TECHNOLOGY FORESIGHT KERS A DEEP DIVE INTO KINETIC ENERGY RECOVERY SYSTEMS – PART 1 20 www.autotechwww.autotechreview.comreview.com AUTHORS INTRODUCTION issue of kinetic energy recovery through regenerative braking has received Vehicle manufacturers, and their suppli- increased attention. A pressing need to ers, are exploring every possible opportu- reduce battery size, increase range and nity of improving fuel economy. One such performance as well as the ability of elec- opportunity exists in recovering the tric drives to operate in regenerative mode kinetic energy that is lost due to braking. has made regenerative braking specifically ARGHYA SARDAR For a vehicle, the positive inertia kinetic relevant for electric drive vehicles. Regen- is Scientist E & Head, Transportation energy equals the negative inertia kinetic erative braking along with Anti-lock Brak- Division at TIFAC, Department of Science & Technology, Government energy over a stop-start sequence and ing System (ABS) feature enhances the of India. over a driving cycle. driving experience because of the precise In a conventional vehicle, deceleration control on the acceleration and decelera- is caused by four forces – aerodynamic tion of the vehicle. drag, rolling resistance, driveline friction, It is in this context, a review of various and friction braking. Among these, the KERS and their future potential is rele- first two are irretrievable losses. However, vant. This article attempts to explore how it is possible to recover a part of the various KERS would evolve and the type RAKESH KUMAR DEY kinetic energy that would otherwise have of vehicles they would be applied to. In is Project Associate at TIFAC, been lost in friction braking as heat. the second part of the article, scheduled Department of Science & Technology, Government of India. Kinetic energy storage devices have for our July 2015 edition, we would com- been in use since ancient times – pottery pare the technologies, and discuss the wheels and spinning wheels being some regenerative braking strategies. of the examples. Flywheels have been used with steam engines and internal combustion engines to smoothen the fluc- TYPES OF KINETIC ENERGY tuating torque produced by the reciprocat- RECOVERY SYSTEMS SURESH BABU MUTTANA ing motion of the pistons of such is Scientist C at TIFAC, Department machines. Regenerative braking is a very There are three types of kinetic energy of Science & Technology, Government of India. well-established technology in transporta- recovery systems available currently – the tion, particularly in electric locomotives. mechanical energy storage system in the Currently used in racing and sports form of a flywheel, hydraulic system and vehicles, Kinetic Energy Recovery Systems an electrical energy storage system in the (KERS) are being seriously considered for form of battery or ultra capacitor. conventional IC engine as well as hybrid Although kinetic energy recovery electric vehicles. With the electric and through regenerative braking is a well- hybrid electric vehicles starting to make established technology in case of locomo- inroads into the commercial space, the tives, there is a major difference in case of Containment disks Flywheel Rim Vacuum seal Touchdown ring Flywheel Hub Flywheel bearing Vacuum port Containment Ring Speed sensor Flywheel Housing 1 Typical Flywheel and components autotechreview June 2015 Volume 4 | Issue 6 21 TECHNOLOGY FORESIGHT KERS Flywheel LOW SPEED HIGH SPEED flywheel needs to rotate at high speed, or it should have a large diameter. Thus, RPM < 10,000 15,000-100,000 for automotive applications, high speed is the desired characteristics, so that TECHNOLOGY Mature Recent both weight and footprint can be mini- mised. Rotor materials selection, its ROTOR Steel (Vmax = 300 m/s) Composite Fibre (Vmax = 1,000 m/s) dimensioning and the structure connect- ing the rotor become important issues. BEARING Conventional (heat) Ceramic; magnetic As a technology, flywheel has evolved over the last few decades. 2 SURROUNDING Air (air resistance) Vacuum lists a brief status of the technology. Five categories of materials that are SAFETY REQUIREMENT Low High generally used for flywheel design and their properties are given in 3. In order COST Low High to reduce weight, engineers who design Formula 1 race cars have tried to use 2 Type of flywheels and their characteristics composite materials in flywheels. Fur- ther, in order to reduce friction, the fly- wheels were sealed inside a vacuum road vehicles. Whereas in case of loco- sion is used to control and transfer the chamber. R&D efforts on modern fly- motives, there are options either to feed energy to and from the driveline. The wheels focus on materials such as power (DC lines) back to the grid, or pro- transfer of vehicle kinetic energy to fly- alloys, carbon-fibre composites, ceram- vide power to other trains in the line, in wheel kinetic energy can be seen as a ics, and crystalline materials such as case of road vehicles, an on-board energy momentum exchange. When braking is single crystals of silicon. A central part storage system that can receive the recov- initiated, the vehicle is at a high speed of rotor design is the reduction of radial ered energy is essential. and the flywheel at a low speed, giving tensile stresses. Some are specifically For conventional IC engine vehicles, a certain gear ratio between them. At designed to ensure they shatter safely such storage system will have to be the end of braking, the function reverses into tiny fragments, should they spin an additional system, whereas for – the vehicle speed is low, and the fly too fast. electric and hybrid electric vehicles, wheel is at a high speed, thus changing High-speed flywheels have rotors the options are either to use the traction the ratio of speed. During the energy suspended on magnetic bearings, spin- battery, or combine it with an ultra- transfer, the ratio between vehicle speed ning at high speeds (up to 100,000 rpm) capacitor or a flywheel. and flywheel changes continuously. in a vacuum chamber. R&D efforts are The recovered kinetic energy is also being focussed on high temperature stored in the spinning wheel, to be superconductors as bearings, in order to FLYWHEEL released upon acceleration. The amount increase stored energy. of energy a flywheel stores depends on The challenge, however, is to develop In the mechanical system, the available its moment of inertia and the speed at such systems for passenger cars, where, kinetic energy is used to spin a flywheel which it rotates. The moment of inertia, unlike racing cars, the system needs to at high speeds and this motion is trans- in turn, is dependent on the mass and be affordable, and also should last for a ferred back to the wheels via a trans- its distribution. For storing more energy much longer period. In case of racing, it mission, 1. The variable drive transmis- without increasing the mass, either the may be enough for the system to last only for a couple of hours at a time. Using a similar design for consumer cars would need a system to maintain Material Allowable STRESS [σ], MPa DENSITY ρ, KG/m3 the vacuum with pumps and valves, which will add complexity and cost. GREY CAST IRON 220 7,340 Flywheels have been frequently used in high technology application, and usu- ALUMINIUM ALLOY 400 2,700 ally feature vacuum enclosures and magnetic bearing systems so as to mini- MARAGING STEEL 900 8,000 mise frictional losses. CARBON FIBRE COMPOSITES (40% epoxy) 750 1,550 Flywheel EXPERIMENTS E-GLASS FIBRE (40% epoxy) 250 1,900 Use of flywheel as the sole energy storage 3 Flywheel Materials system in the vehicle has been attempted 22 www.autotechreview.com since long. The ‘Gyrobus’ – a city bus mechanical energy for up to 30 min, 20% fuel savings and reducing car- developed by the Maschinenfabrik Oer- releasing it when required to aid in bon emissions. likon in Switzerland in the 1930s, used a acceleration. A six pound flywheel flywheel connected to an electrical made of carbon-composite, wrapped machine as the sole on-board energy around a steel hub, spins in a vac- ELECTRIC STORAGE SYSTEM source. At regular bus stops, power from uum at up to 60,000 rpm, recapturing electrified charging stations was used to somewhere around 40 hp of instanta- Regenerative braking system utilises the accelerate the flywheel. In between the neous power. It is claimed that the electric motor, providing negative torque bus stops, the kinetic energy of the fly- system has the potential to reduce to the driven wheels and converting wheel was used to produce electrical fuel consumption by up to 25 %, and kinetic energy to electrical energy for energy by the electrical machine, which in improve acceleration by 1.5 s by recharging the battery, 4. Kinetic energy turn, ran an electrical motor. Once reaching a speed of 100 km/h from can be converted back into electrical charged, Gyrobus could run six km in reg- being stationary in 5.5 s. energy, which can be stored in batteries ular traffic. There are examples of devel- :: GKN Gyrodrive, a flywheel system for reuse to propel the vehicle during the opment efforts to use flywheel-based that has been used in motorsports, is driving cycle. The existing inverter of the KERS in vehicles with IC engines. Some available for hybrid buses and other electric drivetrain can be utilised for examples are: passenger and commercial vehicles. recovering the braking energy with added :: Jaguar has tested a flywheel hybrid Go-Ahead Group plc, the UK-based regenerative control algorithms. (IC engine + flywheel) that promises operator of train and bus services, In many modern electric and hybrid a power boost of about 81 hp, and up plans to implement this technology electric vehicles, electric KERS has been to a 20 % fuel economy improve- in 500 of its 4,600 buses.
Load more

Recommended publications
  • The Electromechanical Battery
    12 13 A New Look at an Old Idea TheThe ElectromechanicalElectromechanical BatteryBattery Laboratory researchers PINNING at 60,000 revolutions “charged” by spinning its rotor to lead–acid battery. Power densities can S per minute, a cylinder about the maximum speed with an integral soar to 5 to 10 kW/kg, several times size of a large coffee can may hold the generator/motor in its “motor mode.” that of a typical gasoline-powered are integrating innovative key to the long-awaited realization of It is “discharged” by slowing the rotor engine and up to 100 times that of practical electric cars and trucks. The of the same generator/motor to draw out typical electrochemical batteries. And materials and designs to graphite, fiber-composite cylinder the kinetically stored energy in its because of its simple design and belongs to a new breed of LLNL- “generator mode.” The advanced design advanced materials, an EMB is developed, flywheel-based, energy features a special array of permanent expected to run without maintenance develop highly efficient storage systems with new materials, magnets (called a Halbach array) in the for at least a decade. new technologies, and new thinking generator–motor to perform these Livermore researchers envision about the most efficient ways to charging and discharging functions several small, maintenance-free and cost-effective energy store energy. efficiently. modules, each with a kilowatt-hour of Called an electromechanical battery The EMB offers significant energy storage, for use in electric or (EMB) by its Laboratory creators, the advantages over other kinds of energy hybrid-electric vehicles. See the storage.
    [Show full text]
  • Flywheel Energy Storage for Automotive Applications
    Energies 2015, 8, 10636-10663; doi:10.3390/en81010636 OPEN ACCESS energies ISSN 1996-1073 www.mdpi.com/journal/energies Review Flywheel Energy Storage for Automotive Applications Magnus Hedlund *, Johan Lundin, Juan de Santiago, Johan Abrahamsson and Hans Bernhoff Division for Electricity, Uppsala University, Lägerhyddsvägen 1, Uppsala 752 37, Sweden; E-Mails: [email protected] (J.L.); [email protected] (J.S.); [email protected] (J.A.); [email protected] (H.B.) * Author to whom correspondence should be addressed; E-Mail: [email protected]; Tel.: +46-18-471-5804. Academic Editor: Joeri Van Mierlo Received: 25 July 2015 / Accepted: 12 September 2015 / Published: 25 September 2015 Abstract: A review of flywheel energy storage technology was made, with a special focus on the progress in automotive applications. We found that there are at least 26 university research groups and 27 companies contributing to flywheel technology development. Flywheels are seen to excel in high-power applications, placing them closer in functionality to supercapacitors than to batteries. Examples of flywheels optimized for vehicular applications were found with a specific power of 5.5 kW/kg and a specific energy of 3.5 Wh/kg. Another flywheel system had 3.15 kW/kg and 6.4 Wh/kg, which can be compared to a state-of-the-art supercapacitor vehicular system with 1.7 kW/kg and 2.3 Wh/kg, respectively. Flywheel energy storage is reaching maturity, with 500 flywheel power buffer systems being deployed for London buses (resulting in fuel savings of over 20%), 400 flywheels in operation for grid frequency regulation and many hundreds more installed for uninterruptible power supply (UPS) applications.
    [Show full text]
  • Green BRT in Tehran
    International Journal of Environmental Science P. Parvizi et al. http://iaras.org/iaras/journals/ijes Green BRT in Tehran P. Parvizi, S. Hajeb, P. Parvizi Abstract— Population growth and urban development in recent A Tehran public transport network composed of two layers years, has created many problems in the transport field of major ,Subway and BRT networks .Subway as the first layer cities. Increased traffic, noise and air pollution in large cities is the including 5 lines and BRT network including 10 high-speed phenomenon of negative consequences. Creation Appropriate lines as the second layer are defined in the Tehran integrated infrastructure to facilitate the use of the public transport system is the best option for confronting with this problem. With the advent BRT public transport [1]. system and dedicated public transport corridor for the public In Iran, the BRT system has been implemented in Tehran. transport system, speed and volume displacement increases and thus Tehran Bus Rapid Transit has been officially inaugurated by reducing private car traffic and pollution levels have declined. This Tehran’s mayor in order to facilitate the motor traffic in paper presents the design of bus and bus stations equipped with solar Tehran on January 14, 2008. Tehran has five BRT lines. The cells, with ability isolated and connect power supplies between bus first stretch of Tehran BRT corridor from the Azadi square in and stations to elimination of fossil fuel in the path of Tehran BRT to increase efficiency and reduce environmental lead contamination. In Tehran-pars has been operational since Jan (2008) [2].
    [Show full text]
  • Flywheel Energy Storage for Vehicle Applications
    Scuola di Ingegneria Industriale e dell’Informazione Laurea Magistrale in Ingegneria Meccanica Flywheel energy storage for vehicle applications Ettore Rasca 841979 Supervisor: prof. Francesco Braghin Academic Year 2016-2017 Esprimo il mio ringraziamento a Stefano Sorti per tutto il supporto fornito. Abstract 1 Abstract In recent years, a significant increase in the market share of electric vehicles was observed. Most of these vehicles are meant for private use and are equipped with chemical batteries. Despite the huge improvements made on the capacity of the new generation lithium ion batteries, the long charging time remains a main drawback of this technology and opens the possibility for alternative solutions. The present work describes a preliminary study aimed at investigating the possibility to realize an electric vehicle relying on the flywheel energy storage technology as a primary energy source. First, a numerical and an analytical model of such a system are proposed and evaluated. Next, two sets of optimizations are performed on these models. Through the first optimization set, the optimal geometry for the rotors in the energy storage system is identified. This first process is repeated several times considering different alternatives for the rotors material, maximum rotational speed and basic geometry. Through the second optimization set, the ideal displacement and orientation of the rotors on the vehicle frame, as well as the total number of rotors, are investigated. Finally, three multi-rotor configurations for the energy storage system are proposed and described. The data collected after performing simulations on the dynamics of these systems are then studied. In conclusion, after presenting observations on the feasibility of such a technical solution, a set of future steps for the development of the flywheel energy storage technology for vehicle applications are proposed.
    [Show full text]
  • (Chapter Title on Righthand Pages) 1
    Innovative Perspective of Transport and Logistics BURNEWICZ Jan; BORKOWSKI Przemysław INNOVATIVE PERSPECTIVE OF TRANSPORT AND LOGISTICS BURNEWICZ Jan; University of Gdansk BORKOWSKI Przemyslaw, University of Gdansk ABSTRACT The need to create and implement innovation in transport results from the continuing low efficiency of many of its technical elements and processes, leading to unsatisfactory levels of productivity, capacity and reliability, waste of time and resources, and higher operating costs. The need for innovation exists both within entire transport systems (of a country or city) as well as within individual modes or forms of transport. Transport innovation processes are the main driving force behind technological progress and increase in service productivity, but they are accompanied by high risk. An innovation-oriented transport company takes a risk that innovations introduced may become a failure, or rejected by the market, or their cost will be higher than originally planned. To main directions of the innovative development of present transport systems belong: intelligent transport system management, carbon neutral transport solutions, alternative fuels and sources of energy, innovative ideas for reducing transport costs, city logistics ideas, new mobility strategies, liveability solutions. In every branch of transport there exist different conditions for the initiation and spreadings of innovations. Keywords: alternative fuels, disruptive technology, electric cars, innovation, innovation risk, innovative transport, new generation transport infrastructure, transport development, INTRODUCTION The motives for creating innovations are both the creative capabilities of scientific research centres and industry as well as pressure from consumers for a greater higher of products and services, and elimination of faults in things and processes commonly used.
    [Show full text]
  • Lrt's Key Role In
    THE INTERNATIONAL LIGHT RAIL MAGAZINE www.lrta.org www.tautonline.com OCTOBER 2019 NO. 982 LRT’S KEY ROLE IN A ‘bALTIC BIG BANG’ Creating a sustainable gateway to Estonia’s booming capital Hopes revived for Leeds tram network Ottawa opens Confederation LRT line Shanghai doubles Songjiang tramway South Wales Tampere £4.60 The urban rail Re-imagining a revolution begins... post-industrial city 2019 2 October 2019 – London Recognising excellence and innovation in the global light and urban rail sector. Book your place now! SUPPORTED BY ColTram www.lightrailawards.com CONTENTS 369 The official journal of the Light Rail Transit Association OCTOBER 2019 Vol. 82 No. 982 www.tautonline.com EDITORIAL EDITOR – Simon Johnston [email protected] ASSOCIATE EDITOr – Tony Streeter [email protected] WORLDWIDE EDITOR – Michael Taplin 375 [email protected] NewS EDITOr – John Symons [email protected] SenIOR CONTRIBUTOR – Neil Pulling WORLDWIDE CONTRIBUTORS Richard Felski, Ed Havens, Andrew Moglestue, Paul Nicholson, Herbert Pence, Mike Russell, Nikolai Semyonov, Alain Senut, Vic Simons, Witold Urbanowicz, Bill Vigrass, Francis Wagner, Thomas Wagner, Philip Webb, Rick Wilson ampere/Wille Nyyssönen ampere/Wille T PRODUCTION – Lanna Blyth 385 of ity Tel: +44 (0)1733 367604 C [email protected] NEWS 364 neXT-generation: luXembourg 382 DESIGN – Debbie Nolan Ottawa finally opens Confederation LRT line; With the initial tram service established, ADVertiSING Jerusalem win grows CAF by 25%; Shanghai Luxembourg City looks to expansion. COMMERCIAL ManageR – Geoff Butler opens latest Songjiang extension; Phoenix Tel: +44 (0)1733 367610 [email protected] votes for LRT; Bombardier wins in Dresden.
    [Show full text]
  • Technologies Des Transports Transport Des Personnes 2
    Technologies des transports Transport des personnes 2. Modes publics et privés | Modes sur rue CIV6707A Par Pierre-Léo Bourbonnais Référence principale: VUCHIC, Vukan R. Urban Transit Systems and Technology, 2007 Chapitres 2 & 5 à 10 Des extraits du livre VUCHIC, Vukan R. Urban Transit Systems and Technology, © 2007 John Wiley & Sons, Inc. sont insérés dans ce 1 document avec la permission de l’éditeur CIV6707A Technologies des transports • Transport des personnes | Modes publics et privés • Modes sur rue Modes sur rue Caractéristiques 3 types de lignes Avantages Bus conventionnel ‣ faible coût d’investissement ‣ catégorie C, circulation mixte/partagée ‣ peuvent rouler sur pratiquement n’importe quelle rue ‣ adéquat pour service local ‣ flexibilité (changements de routes, d’arrêts, detours...) ‣ non compétitif avec l’auto ‣ implantation rapide ‣ Amérique du Nord | souvent perception à ‣ les véhicules les plus économiques entre l’avant seulement et arrêts à chaque 15 et 60 passagers par unité intersection ‣ peuvent être améliorés par des ‣ embarquements plus lents traitements préférentiels ‣ vitesses commerciales ↓ Avantage ou inconvénient selon le contexte BHNS / BTS (Bus à haut niveau de service) ‣ faible influence sur l’aménagement ‣ catégorie C améliorée urbain ‣ optimisation et intégration des lignes Désavantages ‣ traitement préférentiel (voies réservées...) ‣ sensibles à la congestion (catégorie C) ‣ applicable presque partout ‣ faible identité (image) fréquente confusion SRB / BRT (Service rapide par bus) ‣ capacités limitées ‣ catégorie
    [Show full text]
  • City Research Online
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by City Research Online Dhand, A. & Pullen, K. R. (2015). Review of battery electric vehicle propulsion systems incorporating flywheel energy storage. International Journal of Automotive Technology, 16(3), pp. 487-500. doi: 10.1007/s12239-015-0051-0 City Research Online Original citation: Dhand, A. & Pullen, K. R. (2015). Review of battery electric vehicle propulsion systems incorporating flywheel energy storage. International Journal of Automotive Technology, 16(3), pp. 487-500. doi: 10.1007/s12239-015-0051-0 Permanent City Research Online URL: http://openaccess.city.ac.uk/8253/ Copyright & reuse City University London has developed City Research Online so that its users may access the research outputs of City University London's staff. Copyright © and Moral Rights for this paper are retained by the individual author(s) and/ or other copyright holders. All material in City Research Online is checked for eligibility for copyright before being made available in the live archive. URLs from City Research Online may be freely distributed and linked to from other web pages. Versions of research The version in City Research Online may differ from the final published version. Users are advised to check the Permanent City Research Online URL above for the status of the paper. Enquiries If you have any enquiries about any aspect of City Research Online, or if you wish to make contact with the author(s) of this paper, please email the team at [email protected]. Review of Battery Electric Vehicle Propulsion Systems incorporating Flywheel Energy Storage Aditya Dhand, Keith Pullen School of Engineering and Mathematical Sciences City University London London EC1V 0HB, UK Email: [email protected] Abstract The development of battery electric vehicles (BEV) must continue since this can lead us towards a zero emission transport system.
    [Show full text]
  • Bustransport.Pdf
    Bus travel is becoming a popular option for lots of people in our community. Using buses to travel to and from school reduces the number of car journeys. Taking the bus is cheaper, better for the environment and safer for students as the number of vehicles near schools is reduced. The main purpose of this study unit is for students to learn more about our bus transport system. Teachers should assist students to choose activities appropriate to their level and ability. Curriculum links are listed to help teachers track progress. The Taranaki Regional Council website www.trc.govt.nz can be used to download the unit and as a source for research to assist with some of the activities. The main areas covered by the unit are: Key Competencies • Managing self • Using language, symbols and text • Participating and contributing • Relating to others • Thinking Essential Skills • Communication • Numeracy • Information gathering • Problem solving • Self-management and competitive • Physical • Work and study Values • Excellence • Innovation • Equity • Community and participation • Respect 1 Activity 1: Background information Social Sciences – Identity, Culture and Organisation Key Competencies: Values: • Using language, symbols and text • Excellence • Relating to others • Innovation • Thinking • Equity • Community and participation Essential Skills: • Respect • Work and study • Information Questions: 1. Name the towns in Taranaki where bus services are available. 2. Explain the difference between a chartered bus, a school bus and one that operates regularly on a specific run. 3. What are the benefits to the community of an efficient public bus service? 4. Why is it important that bus services are reliable and run to time? 5.
    [Show full text]
  • City Research Online
    Dhand, Aditya (2015). Design of electric vehicle propulsion system incorporating flywheel energy storage. (Unpublished Doctoral thesis, City University London) City Research Online Original citation: Dhand, Aditya (2015). Design of electric vehicle propulsion system incorporating flywheel energy storage. (Unpublished Doctoral thesis, City University London) Permanent City Research Online URL: http://openaccess.city.ac.uk/13699/ Copyright & reuse City University London has developed City Research Online so that its users may access the research outputs of City University London's staff. Copyright © and Moral Rights for this paper are retained by the individual author(s) and/ or other copyright holders. All material in City Research Online is checked for eligibility for copyright before being made available in the live archive. URLs from City Research Online may be freely distributed and linked to from other web pages. Versions of research The version in City Research Online may differ from the final published version. Users are advised to check the Permanent City Research Online URL above for the status of the paper. Enquiries If you have any enquiries about any aspect of City Research Online, or if you wish to make contact with the author(s) of this paper, please email the team at [email protected]. School of Engineering and Mathematical Sciences Design of electric vehicle propulsion system incorporating flywheel energy storage PhD Thesis Aditya Dhand Submitted to City University London in partial fulfilment of the requirements for the degree of Doctor of Philosophy (PhD) May 2015 Abstract Battery electric vehicles are crucial for moving towards a zero emission transport system. Though battery electric vehicle technology has been rapidly improving, it is still not competitive to the conventional vehicles in terms of both cost and performance.
    [Show full text]
  • Technologies Des Transports Transport Des Personnes Résumé | Les Systèmes De Transport CIV6707A ! Par Pierre-Léo Bourbonnais Référence Principale: VUCHIC, Vukan R
    Technologies des transports Transport des personnes Résumé | Les systèmes de transport CIV6707A ! Par Pierre-Léo Bourbonnais Référence principale: VUCHIC, Vukan R. Urban Transit Systems and Technology, 2007 Chapitres 2 & 5 à 10 Des extraits du livre VUCHIC, Vukan R. Urban Transit Systems and Technology,1 © 2007 John Wiley & Sons, Inc. sont insérés dans ce document avec la permission de l’éditeur CIV6707A Technologies des transports • Transport des personnes | Modes publics et privés • Classification des systèmes de transport Contenu de la présentation • Priorités de passage et • Modes sur rail • Comment les évaluer? vitesses • Tramway (Streetcar) • Courtes distances • Évolution optimale d’une • SLR • Téléphériques ville • SRR / Métros • Bateaux et traversiers • Modes sur rue • Trains régionaux / Trains • Modes parallèles • Minibus de banlieue • Location de voitures et • Midibus • Tram-train covoiturage • Bus régulier • Véhicules et design • Semi-public • Bus articulé et bi-articulé • Impacts • Autopartage • Bus à impériale • Coûts • Taxi • Trolleybus • Tendance et rôles futurs • Transport à la demande • Bus guidé • TGV • Rôle des modes parallèles • Bus interurbain • Modes spécialisés • Choix des technologies et • Modes de propulsion AGT des modes et • comparaisons • Design • APM • Traitements préférentiels • Monorail • Tableau récapitulatif • SRB PRT • Conclusions et • perspectives 2 CIV6707A Technologies des transports • Transport des personnes | Modes publics et privés • Classification des systèmes de transport Systèmes de transport collectif
    [Show full text]
  • A Practical, 70-90% Electric Bus Without Overhead Wires
    EVS24 Stavanger, Norway, May 13-16, 2009 A Practical, 70-90% Electric Bus without Overhead Wires Roger Bedell Opbrid Transporte Sostenible S.L., Calle Tibero 7, Cenes de la Vega, Granada, Spain, +34 626-855-662 [email protected] Abstract Lithium titanate (Li4Ti5O12 or LTO) batteries have two properties that enable a new type of urban bus system: rapid charging and long cycle life. By placing a rapid charger at both ends of a bus route, LTO equipped hybrid buses can run most of the time (70-90%) in electric-only mode. A rapid charger fills the batteries each time a driver reaches the end of route. Existing hybrid diesel-electric buses with backup diesel generators are used to prevent stranding. This Rapid Charge Hybrid (RCH) approach requires virtually no changes to existing hybrid bus designs or fleet behavior, and requires little additional infrastructure. Keywords: bus, fast charge, public transport, series HEV, lithium battery 1 Introduction documented advantages compared to diesel bus fleets. These include fewer public health impacts, Recent advances in battery technology are less noise, less pollution, and improved enabling novel solutions to existing problems. A sustainability.[1] rapid charge hybrid (RCH) system which allows urban transit buses to substitute electricity for Combining the flexibility of diesel buses with the diesel in a practical manner using existing advantages of electric buses has long been an technologies with minimal changes to existing elusive goal with several attempts having been fleets is described here. If the electricity comes made in the past[2]. However, with the new nano from renewable sources such as wind and solar, technology lithium titanate (LTO) batteries, this then RCH is a sustainable transit system.
    [Show full text]