High Efficiency Moped a MQP Proposal Submitted to the Faculty Of

Total Page:16

File Type:pdf, Size:1020Kb

High Efficiency Moped a MQP Proposal Submitted to the Faculty Of High Efficiency Moped A MQP Proposal Submitted to the Faculty of the WORCESTER POLYTECHNIC INSTITUTE in partial fulfillment of the requirements for the Degree of Bachelor of Science in Mechanical Engineering by ___________________________________ Tim Ellsworth Date: 10/11/2012 Approved: Prof. Kenneth Stafford, Major Advisor Prof. Cosme Furlong-Vazquez Table of Contents List of Tables ................................................................................................................................................. 4 List of Figures ................................................................................................................................................ 5 Abstract ......................................................................................................................................................... 7 Executive Summary ....................................................................................................................................... 9 Introduction ................................................................................................................................................ 12 Objective ................................................................................................................................................. 12 History ..................................................................................................................................................... 13 Component Selection .................................................................................................................................. 16 Specifications .......................................................................................................................................... 16 Specifications Defined ............................................................................................................................. 16 Engine...................................................................................................................................................... 21 Gasoline (two-stroke vs. four-stroke) ................................................................................................. 21 Diesel ................................................................................................................................................... 21 Electric Motor ..................................................................................................................................... 22 Propane/Natural Gas .......................................................................................................................... 22 Selection .............................................................................................................................................. 23 Drive Train ............................................................................................................................................... 30 Harmonic Drive ................................................................................................................................... 31 Jack Shaft............................................................................................................................................. 33 Single Stage Spur gear and chain combination ................................................................................... 34 Compound reverted and chain ........................................................................................................... 34 Planetary Gear Train ........................................................................................................................... 35 Engine to Planetary ................................................................................................................................. 37 Dog Clutch Mechanism ........................................................................................................................... 38 Dog Clutch ........................................................................................................................................... 39 Belt ...................................................................................................................................................... 39 Friction Disc ......................................................................................................................................... 39 Basket .................................................................................................................................................. 40 Electronic ............................................................................................................................................ 40 Band Brake Planetary .......................................................................................................................... 40 Pneumatic ........................................................................................................................................... 40 1 Centrifugal ........................................................................................................................................... 40 Freewheels .............................................................................................................................................. 40 Bicycle ..................................................................................................................................................... 41 GMC Denali ......................................................................................................................................... 42 Roadmaster Granite Peak ................................................................................................................... 42 Design .......................................................................................................................................................... 44 Preliminary Designs................................................................................................................................. 44 Design Iteration 1 ................................................................................................................................ 44 Design Iteration 2 ................................................................................................................................ 46 Design Iteration 3 ................................................................................................................................ 48 Design Iteration 4 ................................................................................................................................ 51 Engine plate ........................................................................................................................................ 55 Final Design ............................................................................................................................................. 56 Controls ............................................................................................................................................... 56 Support Brackets ................................................................................................................................. 60 Engine to Gearbox Chain System ........................................................................................................ 64 Dog Clutch ........................................................................................................................................... 69 Manufacturing ............................................................................................................................................ 70 Manual .................................................................................................................................................... 71 CNC .......................................................................................................................................................... 76 Design for Manufacturability .................................................................................................................. 77 Results and Testing ..................................................................................................................................... 78 Robustness Testing ................................................................................................................................. 78 Motor mount movement .................................................................................................................... 78 Planetary output sprocket failure ....................................................................................................... 78 Motor to crank derailment and alignment problem .......................................................................... 79 Improperly installed 3/8 drive shafts .................................................................................................. 81 Engine to Planetary Issues .................................................................................................................. 81 Failure of #25 1:1 chain ....................................................................................................................... 82 Power Estimation ...................................................................................................................................
Recommended publications
  • Design of Continuously Variable Bicycle Transmission
    Innovative Bicycle Drivetrain Design of continuously variable bicycle transmission Author: Jean Kolb Supervisor: Dr Eng. Slawomir Kedziora Chain drive with derailleur change mechanism . 98.5% efficiency . Relatively low weight . The most common drivetrain . Not innovative NuVinci CVT hub . Continuously variable ratio . Torque transmitted by traction . Ball planets change the contact angle Source: https://www.fallbrooktech.com/nuvinci-technology CVT hub by Hiroyuki Urabe . Used as reference for own design . Upstream planetary gear train and roller train . Estimated efficiency of 90% . Patented, but not developed CVT hub by Hiroyuki Urabe Pros Cons . Different and innovative . Relatively heavy weight . Continuously variable . Lower transmission efficiency . Enhanced e-bike engine . More complex than the efficiency comparable design from . Protected in hub enclosure “NuVinci” . Clean look Presentation and explanation of the developed design CVT hub Developed CVT hub Autodesk Fusion 360 unites every development step Cloud computing Developed CVT hub Developed CVT hub Upstream planetary gear train Input Output Sprocket Input Input torque on ring gear Fixed carrier Developed CVT hub Planetary roller train Output Input Input torque on sun roller Non-rotatable but on axle displaceable carrier Preloaded spring Preloaded spring to guarantee enough traction Wave spring Preloaded spring Spline Radial bearing on slidable sleeve Needle bearings Axial bearing gets pushed Left handed thread Gap between roller and sun Left handed thread Changing
    [Show full text]
  • Basic Gear Systems
    Basic Gear Systems A number of gears connected together is called a “Gear Train”. The gear train is another mechanism for transmitting rotary motion and torque. Unlike a belt and pulley, or chain and sprocket, no linking device (belt or chain) is required. Gears have teeth which interlock (or mesh) directly with one another. Advantages The main advantages of gear train transmission systems are that because the teeth on any gear intermesh with the next gear in the train, the gears can't slip. (An exact ratio is maintained.) Large forces can be transmitted. The number of turns a gear makes can be easily controlled. High ratios between the input and the output are easily possible. Disadvantages The main disadvantage of a gear system is it usually needs a lubrication system to reduce wear to the teeth. Oil or grease is used to reduce friction and heat caused by the teeth rubbing together. Gear systems to increase and decrease rotational velocity Gears are used to increase or decrease the speed or power of rotary motion. The measure of how much the speed or power is changed by a gear train is called the gear ratio (velocity ratio). This is equal to the number of teeth on the driver gear divided by the number of teeth on the driven gear. To decrease the speed of the output the driver gear is smaller than the driven gear. (This will reduce the speed but increase the “torque”.) This diagram shows a small gear (A) driving a larger gear (B). Because there are more teeth on the driven gear there is a reduction in output speed.
    [Show full text]
  • HS Code Product Description 23012010 Fish Meal for Feed
    Note: All products that are classified in the 8‐digit subheadings of the Harmonized Tariff Schedule HS Code Product description 23012010 Fish meal for feed 26180010 Manganese slag produced by smelting steel 26190000 Slag, scum, scale and other waste generated from smelting steel 26209990 Mineral ash and residue containing other metals and compounds 27011100 Unformed anthracite, whether or not powdered 27011210 Unformed coking bituminous coal, whether or not powdered 27011290 Other bituminous coal not made, whether or not powdered 27011900 Other coal not made, whether or not powdered 27012000 Coal brick, briquettes and similar solid fuels made of coal 27021000 lignite 27022000 Finished brown coal 27030000 Peat (including peat for fertilizer) regardless of molding 27040010 Coal coke and semi-coke regardless of molding 27040090 Charcoal Gas, water gas, furnace gas and similar gases, except for petroleum gas and other hydrocarbon 27050000 gases Tar and mineral tar distilled from coal, lignite, or peat, whether or not dehydrated or partially 27060000 distillation, including reconstitution of tar 27071000 crude benzene 27072000 Crude toluene 27073000 Crude xylene 27074000 naphthalene Other aromatic mixtures, by volume of aromatics distilled at 250 ° C by volume (including loss) at 27075000 65% or more 27079100 creosote 27079910 phenol Other products obtained by distillation of coal tar; aromatics weighing more than non-aromatic 27079990 ingredients product 27081000 Asphalt from coal tar or other mineral tar 27082000 Bituminous coke derived
    [Show full text]
  • Motorcycle, Motorized Bicycle and Electric-Assisted Bicycle Manual
    Motorcycle, Motorized Bicycle and electric-assisted Bicycle Manual Minnesota Department of Public Safety Driver and Vehicle Services Division www.mndriveinfo.org Minnesota Motorcycle, Motorized Bicycle and Electric-Assisted Bicycle Manual The Minnesota Department of Public Safety Driver and Vehicle Services Division prepared this manual. Visit the Department of Public Safety Web site at www.mndriveinfo.org to access online versions of our driver’s manuals. PS30001-12 (2/11) About this Manual… This manual is about operating For more information on Minnesota motorcycles, motorized bicycles and driving laws and rules for all drivers, electric-assisted bicycles on Minnesota refer to the Minnesota Driver’s streets and highways. Manual. The first section concerns Minnesota This manual is printed by permission laws and requirements. For complete of the Minnesota Department of standards, consult Minnesota state Public Safety. statutes and rules. This document is This manual is prepared by the not a proper legal authority to cite Division of Driver and Vehicle Services in court. with permission of the Minnesota The second section (Operation Department of Public Safety. Manual) contains information on safe This information can be made motorcycling. The Operation Manual, available in alternative format to provided by the Motorcycle Safety individuals with disabilities. For Foundation, is not about Minnesota assistance, call 651-297-3298 or law — it is about riding smart and TTY 651-282-6555. staying safe. CONTENTS Preface Instruction Permit Process . .VI Rider Training..................I Skills Test ....................VI Duplicate Permits............. VII Motorcycles Vehicle Registration . VII License Endorsement and Permit . II Insurance Requirements ........ VII Permit Process . II Equipment Requirements ....... VII Skills Test ...................
    [Show full text]
  • Meeting Notice and Agenda
    Members Jim Desmond, Chair Mayor, City of San Marcos (Representing North County Inland) Bill Sandke, Vice Chair Councilmember, City of Coronado (Representing South County) Georgette Gomez, Councilmember TRANSPORTATION City of San Diego Ron Roberts, Supervisor COMMITTEE County of San Diego Bill Baber AGENDA Vice Mayor, City of La Mesa (Representing East County) Catherine Blakespear Mayor, City of Encinitas (Representing North County Coastal) Friday, June 16, 2017 Harry Mathis, Chair 9 a.m. to 12 noon Metropolitan Transit System SANDAG Board Room John Aguilera, Vice Chair North County Transit District 401 B Street, 7th Floor Jim Janney San Diego San Diego County Regional Airport Authority Alternates AGENDA HIGHLIGHTS Judy Ritter Mayor, City of Vista • ROSE CREEK BIKEWAY PROJECT: (Representing North County Inland) CONSTRUCTION MANAGER/GENERAL Mary Salas CONTRACTOR CONSTRUCTION SERVICES Mayor, City of Chula Vista (Representing South County) AGREEMENT SUPPLEMENT 7 Mark Kersey, Councilmember City of San Diego • FY 2018 CLAIMS FOR TRANSPORTATION Bill Horn, Supervisor DEVELOPMENT ACT AND STATE TRANSIT County of San Diego ASSISTANCE Greg Cox, Supervisor County of San Diego • FIRST TransNet TEN-YEAR COMPREHENSIVE Jennifer Mendoza Mayor Pro Tem, City of Lemon Grove PROGRAM REVIEW (Representing East County) Ellie Haviland Councilmember, City of Del Mar (Representing North County Coastal) PLEASE SILENCE ALL ELECTRONIC DEVICES DURING THE MEETING Lorie Bragg Metropolitan Transit System YOU CAN LISTEN TO THE TRANSPORTATION COMMITTEE Bill Horn / Mark Packard North County Transit District MEETING BY VISITING OUR WEBSITE AT SANDAG.ORG April Boling San Diego County Regional Airport Authority MISSION STATEMENT The 18 cities and county government are SANDAG serving as the forum for regional decision-making.
    [Show full text]
  • General Applications of Gears
    UNIT - III GEAR MANUFACTURING PROCESS SPRX1008 – PRODUCTION TECHNOLOGY - II Gears are widely used in various mechanisms and devices to transmit power and motion positively (without slip) between parallel, intersecting (axis) and non-intersecting non parallel shafts, •without change in the direction of rotation •with change in the direction of rotation •without change of speed (of rotation) •with change in speed at any desired ratio Often some gearing system (rack – and – pinion) is also used to transform Rotary motion into linear motion and vice-versa. Fig.1 Features of Spur Gear Gears are basically wheels having, on its periphery, equispaced teeth which are so designed that those wheels transmit, without slip, rotary motion smoothly and uniformly with minimum friction and wear at the mating tooth – profiles. To achieve those favorable conditions, most of the gears have their tooth form based on in volute curve, which can simply be defined as Locus of a point on a straight line which is rolled on the periphery of a circle or Locus of the end point of a stretched string while its unwinding over a cylinder as indicated in Fig. General Applications of Gears Gears of various type, size and material are widely used in several machines and systems requiring positive and stepped drive. The major applications are: • Speed gear box, feed gear box and some other kinematic units of machine tools • Speed drives in textile, jute and similar machineries • Gear boxes of automobiles • Speed and / or feed drives of several metal forming machines • Machineries for mining, tea processing etc. • Large and heavy duty gear boxes used in cement industries, sugar industries, cranes, conveyors etc.
    [Show full text]
  • Case Study on HYBRID VEHICLES Power Vehicle Type
    Case Study on HYBRID VEHICLES Power Power sources for hybrid vehicles include: Coal, wood or other solid combustibles Compressed or liquefied natural gas Electricity Electromagnetic fields, Radio waves Electric vehicle battery Human powered e.g. pedaling or rowing Hydrogen On-board or out-board rechargeable energy storage system (RESS) Petrol or Diesel fuel Solar Wind Vehicle type Two-wheeled and cycle-type vehicles Mopeds, electric bicycles, and even electric kick scooters are a simple form of a hybrid, as power is delivered both via an internal combustion engine or electric motor and the rider's muscles. Early prototypes of motorcycles in the late 19th century used the same principles to power it up. In a parallel hybrid bicycle human and motor power are mechanically coupled at the pedal drive train or at the rear or the front wheel, e.g. using a hub motor, a roller pressing onto a tire, or a connection to a wheel using a transmission element. Human and motor torques are added together. Almost all manufactured Motorized bicycles, Mopeds are of this type. In a series hybrid bicycle (SH) the user powers a generator using the pedals. This is converted into electricity and can be fed directly to the motor giving a chainless bicycle but also to charge a battery. The motor draws power from the battery and must be able to deliver the full mechanical torque required because none is available from the pedals. SH bicycles are commercially available, because they are very simple in theory and manufacturing. The first known prototype and publication of an SH bicycle is by Augustus Kinzel (US Patent 3'884'317) in 1975.
    [Show full text]
  • UNIT2.6-Mechanisms: Eng Notes
    EP@BHS-TOPIC 2: Energy, UNIT2.6: Mechanisms Page 1 UNIT 2.6 MECHANISMS: Concepts Addressed in Lesson: 1. Most mechanisms are composed of simple machines, interlocking gears, chain driven sprockets, and belt driven pulleys. 2. Mechanisms are used to transmit energy through a system by manipulating force, speed, and direction. 3. Mechanical advantages mathematically represent the ratio of the force output to the force input for mechanisms. Performance Objectives Addressed in Lesson: It is expected that students will: o Measure forces, speeds, and distances as related to the operation of mechanisms. o Distinguish between the six simple machines, their attributes, and components. o Calculate ideal mechanical advantages, gear ratios, and drive ratios for mechanisms. o Design, create, and test gear, belt-pulley, and/or chain-sprocket systems. o Calculate work, power, torque, and efficiency for mechanical systems. Assessment: Explanation • Students will explain the difference between engineering and engineering technology. • Students will explain the relationship between work and power in a mechanical system. • Students will explain the processes of calculating mechanical advantage. Interpretation • Students will make journal entries reflecting on their learning experiences. • Students will explain the importance and relevance of simple machines in everyday life. Application • Students will apply their knowledge of simple machines and calculate mechanical advantage of objects within the lab environment. • Students will apply their knowledge of system efficiency to calculate efficiency of a mechanical system. • Students will apply their knowledge of gear, sprocket, and pulley systems to calculate speed, distance, rotational direction, and mechanical advantage. Perspective • Students will select an engineering or engineering technology field of interest and prepare an interview with a professional within the field of interest.
    [Show full text]
  • Public Safety Committee Agenda
    PUBLIC SAFETY COMMITTEE AGENDA DATE: December 18, 2019 LOCATION: City Hall Conference Room TtrME: 4:00 P.M. I. CAIL TO ORDER II. ANNOUNCE MEMBERS IN A'|'TENDANCE (VERIFY QUORUM) II]. ADOP]'ION OF MINUTES: October 16.2019 IV. DEPARTMENT REPORTS I . Building & Codes Department: Monthly Reports 2. Police Department: Monlhly Reports 3. Fire Rescue: Monthly Reports COMMITTEE ACTION REQUIRED None VI. CITY COLTNCIL ACTION REQUIRED ORDINANCH 49-2019-20: AN ORDINANCH TO AMEND THE CITY CODE PERTAINING TO A PROHIBITION ON ELECTRIC MOTORIZED BICYCLES. SCOOTERS, AND SKATEBO ARDS (Councilman lkileman) VII. OTHER None VIli. ADJOTJRNMENT IX. PUBLIC COMMENTS 1) Recovery S;,raposium presentation by April Bames. RN, Director of Outreach at The Next Door Treatment Center (Councilman Richmond) PUBLIC SAFETY COMMITTEE MEETING MINUTES October 16,2019 - 4:00 p.m. City Hall Conference Room Attending Committee Members: Councilman Jeff Henley, Chairman; Councilman Erb, Councilman Travis Holleman; Councilman Vonde[1 Richmond: Councilwoman Wanda Smith Others Present: Mayor Joe Pitts, Fire Chief Freddie Montgomery, Police Chief Alonzo Ansley, Building & Codes Interim Director David Smith, Richard Stevens, Kathy Gray The meeting was called to order at 4:00 p.m. by Chairman Henley and it was noted there was a quorum. Minutes from the Scptember 18,2019 meeting were approved by the committee after a motion was made by Councilwoman Smith and seconded bv Councilman Richmond. BUILDING & CODES: -Mr. Smith stated that he would answer any questions regarding the monthly reports Commercial permits are tracking as usual. Permits are up on building, and are close in volume to two years ago. Codes has slowed down, probably due to a reduction in grass growing.
    [Show full text]
  • Electric Bikes and Scooters Snapshot of State Laws
    Electric Bikes and Scooters Snapshot of State Laws State legislators, including those in Montana, are examining state laws, analyzing the use of electronic bikes (e-bikes), and determining how best, if at all, to regulate their use on public streets and paths. According to the National Conference of State Legislature (NCSL), 33 states and the District of Columbia define e-bikes in law.1 Montana is included in that list. Montana law (61-8-102, MCA) defines e-bikes, or “electrically assisted bicycles” as a bicycle 61-8-602, MCA with two operational pedals with a motor attached propels the bicycle and a rider who weighs Traffic laws applicable to persons operating 170 pounds no faster than 20 miles an hour. Essentially, for the purposes of regulation and bicycles or mopeds. A person operating a bicycle or enforcement, an e-bike is treated as a bicycle. The state does not require license or moped is granted all of the rights and is subject to registration. And e-bikes may be ridden on roadways and bicycle paths. all of the duties applicable to the driver of any other vehicle by chapter 7, chapter 9, and this chapter Federal law provides guidance in terms of the manufacturing and sale of e-bikes in the nation. except for special regulations in this part or the Amendments to the Consumer Product Safety Commission passed by Congress in 2002 provide provisions of chapter 7, chapter 9, and this chapter a definition of e-bikes as “A two- or three-wheeled vehicle with fully operable pedals and an that by their nature cannot apply.
    [Show full text]
  • Week 4 Assignment 4 – Detailed Answers
    Week 4 Assignment 4 – detailed answers Due date for this assignment: 2017-08-23, 23:59 IST. Click only the correct answers. There is no negative marking. In all cases of gear Hobbing – assume (i) that the Hob is getting fed past the blank parallel to the axis of rotation of the blank. (ii) And in Helical Hobbing, in addition to the feed of the Hob past the blank along axis of blank, there is additional rotational motion of blank provided through differential mechanism. 1. On the gear hobbing machine, the speed ratio of the Hob and the blank is decided by Option (a) : The number of starts on the Hob and the number of teeth on the Hob Option (b) : The number of teeth on the Hob and the number of teeth to be cut on the part Option (c) : The number of teeth to be cut on the part and the number of starts on the Hob Option (d) : None of the others 1 point Ans : The hob and the gear blank are in reality having motion relation as the worm and worm gear. Hence their speed ratio is k/Z, where k = number of starts on the Hob and Z = number of teeth to be cut on the blank. Hence, option (c ) is the correct answer. 2. There is a right hand helical gear to be cut with helix angle of 150. The left handed hob is having an angle of 30 (Fig. 1). In order to cut the gear on the gear hobbing machine with this Hob, the following configuration is correct Option (a) : A Option (b) : B Option (c) : C Option (d) : D Option (e) : None of the others 1 point Ans : In order to have correct orientation for cutting, the helical thread of the Hob facing the blank should be aligned with (that is, in line with) the potential teeth on the blank.
    [Show full text]
  • Accessibility and Signage for Plug-In Electric Vehicle Charging Infrastructure
    ACCESSIBILITY AND SIGNAGE FOR PLUG-IN ELECTRIC VEHICLE CHARGING INFRASTRUCTURE Report and Recommendations May 2012 This report was developed by the California Plug-In Electric Vehicle Collaborative, a multi-stakeholder partnership working to ensure a strong and enduring transition to a plug-in electric vehicle marketplace. Members played a guiding and consulting role in developing the report, although individual organizations may not formally endorse every recommendation. The PEV Collaborative would like to thank Barbara Lee of the Northern Sonoma County Air Pollution Control District as the lead author of this report. The document was developed by volunteers of the Collaborative Working Groups and Collaborative staff. A special thanks to Dave Head of Sonoma County and Jim Helmer of LightMoves for their contributions. Accessibility & Signage Report www.PEVCollaborative.org 2 May 2012 California Plug-In Electric Vehicle Collaborative James Boyd, 2012 Chairman Diane Wittenberg, Executive Director California Plug-In Electric Vehicle Collaborative California Plug-In Electric Vehicle Collaborative Adrienne Alvord Bonnie Lowenthal Union of Concerned Scientists California State Assembly Robert Babik Richard Lowenthal General Motors Coulomb Technologies Forrest Beanum Ron Mahabir CODA Automotive Greenlots Janice Berman Marvin Moon Pacific Gas and Electric Company Los Angeles Department of Water and Power John Boesel Mary Nichols CALSTART California Air Resources Board Dan Bowermaster Diarmuid O’Connell Electric Power Research Institute Tesla Motors, Inc. Elisabeth Brinton Terry O'Day Sacramento Municipal Utility District NRG Energy Jack Broadbent Alex Padilla Bay Area Air Quality Management District California State Senate Dan Davids Colin Read Plug In America ECOtality Nancy Gioia Clifford Rechtschaffen Ford Motor Company Office of Governor Edmund G.
    [Show full text]