130 Gr Glue: PVA

The Naro-1, previously designated Korea Space Launch Vehicle or KSLV, is South Korea's first carrier rocket, which made its maiden flight on 25 August 2009. It is built by KARI, the national space agency of South Korea along with Korean Air and Khrunichev State Research and Production Space Center (Russia) provided first stage and was launched into space from the country's new spaceport, the Naro Space Center. The official name of the first KSLV rocket, KSLV-I is Naro, which is the name of the region in which Naro Space Center is located.

The KSLV-I launch vehicle is based on the first stage of the Russian Angara rocket combined with a solid-fueled second stage built by South Korea. This configuration is reportedly capable of launching a satellite weighing 100 kilograms into low elliptic orbit.

(from http://en.wikipedia.org/wiki/Naro-1)

H ~ 350 mm Paper used: 0,26 mm - 200 gr ("cardstock") 0,15 mm - 130 gr Glue: PVA

A2 F3a F3 F3 r o t

F2 c 3 e F n

r n o o f c

F1 F3e F3 F3d F3 white ball d = 3,5 mm A1b connector connector for F2 for A2 A1a A2 A1a A1 A3a A3 A3 A1 A2b A2b A2c A2c first glue top of A2c on A1 then glue bottom of A2c on A2

A3b B3b

B2b

B2d A3d c 3 A F3b 3 A

r o f

o A4a t c e

n F3c n o c

A4d A2a

A3e A3 A4

Page 2 print on cardstock © 2010 Designed by L.Cherkashyn This cardmodel is only for personal and not for commercial use slots A4 g g 4 4 2 2 A A P P f f f f f f f f 4 4 4 4 4 4 4 4 A A A A A A A A r 1 o b t P 4 c A 4 e A n

r n o o f c

3 P 3 P h h 4 4 A A

A4c A4

A3f A4h A4e A4e-1 A4e-1

slots glue onto cardstock A4f for A4h-1 A4h-1

spare

B2a B2 B1 B3a B2

B3 A3c cuts for B2c connector B2 for B2 P2 B3 B4

after glue of B4 P1 B2c connector A3c/A4b paint back side P2 to black color two black balls d = 3,5 mm A4b

N1 connector N1 / N2

nozzle P3 insertion N2 P3

A2b A4g

Assembly diagram F3a F3b Fairing F3e F3 Engine F3c of Stage 2 (option) F3d ~5,5 mm B1 A1b B2a A1 A1a B2c A2c Interstage Fairing + engine of Stage 2* A2a A2b B2 B2b A2 B3a B2d 1 - assembly engine of Stage 2 A3a 2 - glue cylinder part of Fairing A3f B3 (F3+F3a+F3b+F3e+F3c) B4 B3b then glue and assembly cone F2 A3b 3 - glue engine into F3 then A3 glue F3d A3c Interstage 1 - glue cone A2 2 - glue cylinder A1 by strip A1a then glue cylinder A1b into A1a 3 - assembly these with cone A2 and glue A2a

______

* engine of Stage 2 is option Stage 1

A3d

A3e A4g

P2 A4a Oxidizer pipe A4f 1 - glue P3 onto A4 A4b A4 2 - glue tube P1 3 - glue P1 into P3 P1 4 - glue P2

A4h A4c A4d A4h-1 1 mm