Honey Brown Ale 4 Oz
Total Page:16
File Type:pdf, Size:1020Kb
Contents Ingredients • Ingredients • Priming Sugar FERMENTABLES • Grain Bag(s) • Bottle Caps 3 lb. Light DME ® • Brewing Procedures 2 lb. Brewer’s Best Wildflower Honey Hops may vary due to availability. SPECIALTY GRAINS Honey Brown Ale 4 oz. Chocolate Barley Glossary 4 oz. Honey Refreshing yet flavorful, this Honey Brown Ale yields 4 oz. Munich Light OG DME 4 oz. Carapils® a malty sweet profile, finishing crisp and almost Original Gravity Dried Malt Extract HOPS lager-like, while the selected hops create a light SG LME 2 packs 1 oz. UK Fuggle Specific Gravity Liquid Malt Extract bitterness for balance. This beer is a perfect choice YEAST FG IBU 1 Sachet any time of the year. Enjoy! Final Gravity International Bittering CO2 Units (Tinseth) IBUs: 19 - 23 OG: 1.042 - 1.046 FG: 1.006 - 1.010 Carbon Dioxide ABV Alcohol by Volume ABV: 4.7% - 5.2% Difficulty: Easy Color: Dark Amber Recommended Procedures Recommended Brew Day Equipment • 4 Gallon Brew Pot (or larger) • Hydrometer BREW DAY (DATE / / ) • 6.5 Gallon Fermenter • Thermometer 1. READ • Airlock • No-Rinse Sanitizer Read all of the recommended procedures before you begin. • Long Spoon or Paddle • Cleanser 2. SANITIZE Thoroughly clean and sanitize ALL brewing equipment and utensils Brew Tips that will come in contact with any ingredients, wort or beer with a 1We suggest doing a 2.5 gallon boil at minimum. If you have the certified sanitizer, e.g., Star San or IO Star. equipment to boil more than 2.5 gallons feel free to do so. There is no need to change the amount of any of the ingredients. 3. STEEP GRAINS 2The grains should not be compacted inside the bag. Grains Pour 2.5 gallons of clean water into your brew pot and begin to heat1. should steep loosely allowing the hot water to soak into all of the Pour crushed grains into grain bag and tie a loose knot at the top of the grain evenly. bag2. When the water is within an appropriate steeping temperature 3Pay careful attention not to let your steeping water exceed 170ºF (150º - 165ºF) place the grain bag into the brew pot3. Steep grains for which leeches tannins into the wort. 4 approximately 20 minutes. Remove grain bag and without squeezing, Run canisters of LME under hot water to allow the extract to pour allow liquid to drain back into brew pot. Your water is now wort. easier. 5Pay careful attention that the extract does not accumulate and caramelize on the bottom of your brew pot. 4. START BOIL 6When consumed, hops can cause malignant hyperthermia in Bring your wort to a gentle, rolling boil. Add all of the included DME dogs, sometimes with fatal results. Even small amounts, including 4 only to the boiling wort . Continuously stir the extract into the wort as “spent” hops from brewing, can trigger a deadly reaction. it returns to a gentle, rolling boil5. 5. FOLLOW SCHEDULE6 As directed on the BREW DAY SCHEDULE (right), slowly sprinkle the BREW DAY SCHEDULE hops into the boiling wort. Be careful not to let the wort boil over the 1. Add one 1 oz. pack of UK Fuggle hops : (time) pot. Using the provided BREW DAY SCHEDULE, note the time the 2. Boil 20 minutes hops were added to help keep your brew on schedule. Continue the 3. Add last 1 oz. pack of UK Fuggle hops : (time) gentle, rolling boil until the boil is complete. 4. Boil 25 minutes 5. Add 2 lb. Brewer’s Best® Wildflower Honey : (time) 6. Boil final 15 minutes 7. Terminate boil Total Boil Time: 60 Minutes Continue to Step #6 Recommended Procedures (continued) Brew Tips 7To avoid bacteria growth do this as rapidly as possible. Do not add ice directly to the wort. 6. COOL WORT & TRANSFER Alternatively, you can use a brewing accessory Cool the wort down to approximately 70ºF by placing the brew pot in a sink filled with ice like a Wort Chiller. 7 water . Pour or siphon wort into a sanitized fermenter. Avoid transferring the heavy sedi- 8Be careful not to add a volume of water that ment (trub) from the brew pot to the fermenter. will cause the wort to fall outside of the OG range specified in the BREW STATS. 9 7. ADD WATER Within 4 - 6 days the bubbling will slow down Add enough clean water (approx. 64º - 72ºF) to the fermenter to bring your wort to until you see no more CO2 being released 10Consider transferring your beer to a second- approximately 5 gallons8. Thoroughly stir the water into the wort. Using a sanitized ary carboy, see “Two-Stage (Secondary) Fer- hydrometer take an Original Gravity (OG) reading. Once you are satisfied your wort is at mentation” sidebar below. the proper volume and within the OG range, record the OG in the ABV% CALCULATOR 11Use standard crown bottles, preferably amber (right). color. Make sure bottles are thoroughly clean. Use a bottle brush if necessary to remove stubborn deposits. Bottles should be sanitized 8. PITCH YEAST prior to filling. Sprinkle the contents of the yeast sachet over top of the entire wort surface (DO NOT REHYDRATE) and stir well with sanitized spoon or paddle. Firmly secure the lid onto the fermenter. Fill your airlock halfway with water and gently twist the airlock into the grommeted lid. Move fermenter to a dark, warm, temperature-stable area (approx. 64º - 72ºF). Two-Stage (Secondary) Fermentation ® FERMENTATION Brewer’s Best recommends home brewers employ the practice of a two-stage fermenta- 9. MONITOR & RECORD tion. This will allow your finished beer to have The wort will begin to ferment within 24 - 48 hours and you may notice CO2 releasing more clarity and an overall better, purer flavor. (bubbling) out of the airlock9. If no bubbling is evident on day two of fermentation, take a All you need is a 5-gallon carboy, drilled stop- gravity reading with a sanitized hydrometer. If gravity has dropped below your OG reading per, airlock and siphon setup to transfer the then fermentation is taking place. Take a gravity reading again in 4 - 6 days10 and confirm beer. You will also need to monitor and record fermentation has completed by comparing the gravity reading to the FG range listed at the SG with your hydrometer when the beer is the top of the instructions. If gravity is not in the FG range, continue fermentation until it in the ‘primary’. When the fermentation slows reaches the FG range. Record your FG reading in the ABV% CALCULATOR (right). (5-7 days), but before it completes, simply transfer the beer into the carboy and allow fer- BOTTLING DAY (DATE / / ) mentation to finish in the ‘secondary’. Leave the beer for about two weeks and then proceed 10. READ to Bottling Day. Consult your local retailer to Read all of the recommended procedures before you begin. learn more about this technique. (SECONDARY RACK DATE / / ) 11. SANITIZE Thoroughly clean and sanitize ALL brewing equipment, utensils, and bottles that will come in contact with any ingredients, wort or beer with a certified sanitizer, e.g., Star San or IO Star. Recommended Bottling Day Equipment 12. PREPARE PRIMING SUGAR • 6.5 Gallon Bottling Bucket • Bottle Brush In a small saucepan dissolve 3.5 oz. of priming sugar into 2 cups of boiling water for 5 • Siphon Setup • Capper minutes. Pour this mixture into a clean bottling bucket. Carefully siphon beer from the • Bottle Filling Wand • Sanitizer fermenter to a bottling bucket. Avoid transferring any sediment. Stir gently for about a • 12 oz. Bottles (approx. 53) minute. 1 oz. of priming sugar is equal to approx. 2.5 tablespoons • Crown Caps 13. BOTTLE Using your siphon setup and bottling wand, fill the bottles11 to within approximately one ABV% Calculator inch of the top of the bottle. Use a bottle capper to apply sanitized crown caps. (OG - FG) x 131.25 = ABV% (_____* - _____**) x 131.25 = ____% 14. BOTTLE CONDITION Move the bottles to a dark, warm, temperature-stable area (approx. 64º - 72ºF). Over the *OG from Step #7 next two weeks the bottles will naturally carbonate. Carbonation times vary depending on **FG from Step #9 the temperature and beer style, so be patient if it takes a week or so longer. CHILL & ENJOY YOUR TASTY BREW AND THANK YOU FOR CHOOSING BREWER’S BEST® PRODUCTS. Brewer’s Best is a registered trademark of the LD Carlson Co..