®

Power SolutionsTM since 1915 Test and Monitoring Equipment

Stationary Power

www.sbsbattery.com 1-800-554-2243 SBS’s Recommended Testing Schedule based on IEEE & NERC PRC-005 X - Meets the minimum requirements of NERC PRC-005-2* X or X meets IEEE Recommendations* IEEE450-2010 Vented / Flooded Lead Acid Batteries (VLA) Monthly Quarterly Yearly 5 Years Visually inspect batteries, rack, charger, room X X X Record battery system float voltage and current at battery terminals X X X Record charger output voltage and current. Correct if needed. X X X Check electrolyte levels. Fill with distilled water to 'max' line if necessary. X X X Record ambient/room temperature X X X Make sure ventilation system is operational X X X Inspect system for unintentional battery grounds X X X Record pilot cell(s) or block(s) voltage and electrolyte temperature X Record pilot cell(s) specific gravity (temp. corrected to 77º F) X Record voltage of ALL cells/blocks X Record specific gravity of 10% of the cells (temp. corrected to 77º F) X Record temperature of 10% of the cells X Record specific gravity of ALL cells (temp. corrected to 77º F) X Record the internal resistance value of ALL cells/blocks X X Record temperature of ALL cells/blocks X Record internal resistance value of ALL cell-to-cell and terminal connections X Conduct load test two years after installation and then every five years. When the system’s capacity falls below 90% load test annually. X

IEEE1106-2005 Nickel Cadmium Batteries Quarterly Semi-Yearly Yearly 5 Years Visually inspect batteries, rack, charger, room X X X Record battery system float voltage and current at battery terminals X X X Record charger output voltage and current. Correct if needed. X X X Check electrolyte levels. Fill with distilled water to 'max' line if necessary. X X X Record ambient/room temperature X X X Make sure ventilation system is operational X X X Inspect system for unintentional battery grounds X X X Record voltage of ALL cells/blocks X X Record temperature of 10% of the cells X X X Record the internal resistance value of ALL cells/blocks X Record temperature of ALL cells/blocks X Record internal resistance value of ALL cell-to-cell and terminal connections X Conduct load test two years after installation and then every five years. When excessive capacity loss is noticed load test annually. X

IEEE1188-2005 Valve Regulated Lead Acid Batteries (VRLA) Monthly Quarterly Yearly 2 Years Visually inspect batteries, rack, charger, room X X X Record battery system float voltage and current at battery terminals X X X Record charger output voltage and current. Correct if needed. X X X Record ambient/room temperature X X X Make sure ventilation system is operational X X X Inspect system for unintentional battery grounds X X X BATTERY TESTING SCHEDULE BATTERY Record voltage of ALL cells/blocks X X Record temperature of ALL cells/blocks at the negative terminal X X Record the internal resistance value of ALL cells/blocks X X Record internal resistance value of ALL cell-to-cell and terminal connections X Conduct load test after initial installation and then every two years or 25% of expected battery life. X *The above testing schedules are based on SBS’s interpretations of both IEEE and NERC PRC-005-2. This information should be used for guidance purposes only and SBS can’t be held responsible if the information is incorrect or if other parties interpret the information differently.

www.sbsbattery.com 1-800-554-2243 [email protected] Table of Contents

Hydrogen Gas Monitoring System

1-2 • SBS-H2

Pg. 1-2 Digital Hydrometers

3-4 • SBS-2002

5-6 • SBS-2003

7 • SBS-2500

8 • SBS-3500 Pg. 3-4 Pg. 4-5 TABLE CONTENTS OF

Internal Resistance Testing Kit

9-10 • SBS-6000

Pg. 9-10 Pg. 9-10

Constant Current DC Load Banks & Multimeters

11-14 • SBS-8400 & Modules

15-16 • SBS-4830S/1110S/1230S/2206S/2415S

• SBS-4815CT 17-18 Pg. 11-14 Pg. 15-16

19-20 • SBS-200CT

21-22 • SBS-600 Digital Multimeter

23-24 • SBS-700 Oscilloscope/Multimeter Pg. 17-18 Pg. 23-24 iv SBS-H2 Hydrogen Gas Detector Complete Hydrogen Monitoring System for Your Battery Room

The SBS-H2 Hydrogen Detector is a complete hydrogen monitoring system with visual and audible alarms. The system comes complete with the main display, a highly accurate hydrogen gas sensor and a 25 ft cable. This unit can be powered with either AC or DC power and can be mounted directly to a wall or to an electrical box making it extremely versatile and very user friendly. The SBS-H2 includes relays for remote connection to alarm/monitoring systems and for control of external relays or an exhaust fan.

Benefits •• The True Hydrogen Gas Detector - single gas detection to eliminate false positives from other gases such as butane, ethanol, and hydrocarbons in the air •• SBS exclusive •• Modular design detector does not require complete replacement for repairs •• Dual AC or DC power supply connections SBS-H2 Package Includes •• UL / CE Certified Hydrogen Sensor for installations & hazardous locations •• Ideal for remote locations •• Main body/display •• Provides coverage redundancy in large monitoring spaces •• Hydrogen sensor •• Protects life, property and company profits •• 25 ft cable

Features •• Universal power inputs: 110/220 Vac or 12-48 Vdc input •• Wall or 2-gang junction box mountable Applications •• Mechanical relays are easily accessible: · Max Switching voltage 28 Vdc, 277 Vac •• .Substations · Rated Current 10A @ 277 Vac, 15A @ 125 Vac •• Battery rooms •• Push button diagnostic test •• .Uninterruptible power supply (UPS) •• Hydrogen sensor is UL Class 1 Division 2, ATEX, and CE certified for hazardous locations •• Battery cabinet systems •• Sensor has a temperature rating of -4° F to 176° F •• .Battery charging areas •• SBS-H2 display allows for a second sensor input to increase coverage area •• .Hydrogen fueled back-up power •• Display can be calibrated in the field with p/n H2-CALKIT option systems •• Can operate in a wide range of temperatures and humidity •• Audible alarm

Available Accessories HYDROGEN GAS DETECTOR

Standard, 2-gang junction box Calibration kit Additional hydrogen sensor/25 ft cable and optional 50 ft and 100 ft cables (Hardwired AC or DC)

1 www.sbsbattery.com 1-800-554-2243 [email protected] HYDROGEN GAS DETECTOR GAS HYDROGEN

Warning Settings: When 1% hydrogen is present in the air the yellow warning light will come on and the warning relay contact will close allowing power to peripherals, such as a vent fan or other devices. Alarm Settings: When at least 2% hydrogen is present in the air the red warning light will come on and an audible alarm activates. In addition, a second alarm relay contact will close which can be used to shut down the system, or notify a building alarm system or other devices.

Ordering Information Main Body/Display: Part No. Description Mounting and Power Options SBS-H2 Hydrogen Detector Package

Accessory Ordering Information Wall-mountable Part No. Description H2-SENSOR Additional hydrogen sensor with 25 ft cable H2-CALKIT Calibration kit H2-JB 4 11/16" x 4 11/16" 2-gang junction box H2-50FT-CABLE 50 ft cable (no hydrogen sensor) Standard, 2-gang junction box H2-100FT-CABLE 100 ft cable (no hydrogen sensor) (Hardwired AC or DC) E190399 AC Cord 110V, 10A, 10 ft with plug

Specifications 1% Hydrogen Energizes a relay which can activate exhaust fan or SCADA system/alarm 18 AWG AC cord recommended 2% Hydrogen Sounds audible alarm and energizes relay which can be used on SCADA system (not included)

Power source 110 / 220 Vac, 50/60 Hz OR 12-48 Vdc (9-60 Vdc operating voltage) Size 4.75" L x 5.25" W x 1.4" D (main body/display)

2 SBS-2002 Digital Hydrometer / Density Meter Digital Specific Gravity Tester for Lead-Acid Batteries

The SBS-2002 is lightweight, durable and easy to use, making it suitable for use in all industrial environments. Simply insert the nozzle into the battery

and depress the finger pump which draws a few drops of sulfuric acid (H2S04) through the tube. Within three seconds the measured refractive index is converted into a temperature-compensated specific gravity reading and then both the specific gravity and temperature are displayed.

Features •• ±0.002 accuracy •• LED display •• For lead-acid batteries only •• IP64 water resistant •• Field calibrate with distilled water

Benefits •• Time savings — 5 times faster than conventional methods •• Measures specific gravity, ambient temperature and count •• Automatically temperature compensates to 77º ˚F (or 25º C)

How the SBS-2002 operates DIGITAL HYDROMETERS DIGITAL

3 www.sbsbattery.com 1-800-554-2243 [email protected] SBS-2002 Digital Hydrometer / Density Meter Digital Specific Gravity Tester for Lead-Acid Batteries

Example of Cost Savings Field studies show time savings of at least 5 times (500%) using a digital hydrometer over a standard glass hydrometer and thermometer. If you spend 60 minutes testing specific gravities every month in 20 sites, this total, 60 minutes x 20 sites x 12 months per year = 14,400 minutes divided by 60 minutes = 240 labor hours per year. Since we can reduce this time by 500%, 240 hours divided by 5 = 48 hours total time with the SBS�2002. That’s a savings of 192 hours per year. Multiplied by $45.00 per hour labor cost with benefits: 192 x $45.00 = $8,640.00 of savings per year.

5 hrs

4 hrs

3 hrs

2 hrs A time savings of over 500% 1 hr with the SBS-2002 0 hrs 5 Units 10 Units 15 Units 20 Units

Standard Glass SBS 2002 DIGITAL HYDROMETERS Hydrometer

Includes Applications •• Main unit •• Utility •• Three (3) silicone tubes •• UPS •• 9V battery •• Data Centers •• Adjustable hand strap •• Telecom •• Instruction manual •• Material Handling •• Case

Specifications Ordering Information Specific gravity of sulfuric acid temp. compensated to 77° F (25° C) Measured Items Part No. Description Temperature of sulfuric acid as electrolyte in lead-acid batteries SBS-2002 Digital specific gravity tester (Fahrenheit only) Display LCD; specific gravity and temperature SBS-2002C Digital specific gravity tester (Celsius only) Measuring Time Within 3 seconds after pushing “START” button Specific gravity: 1.000 to 1.300 Measurement Range Temperature: 41 to 104° F (5 to 40° C) Accessory Ordering Information Measurement Specific gravity: ±0.002 @ 50 to 86° F (10 to 30° C) Part No. Description Accuracy Temperature: ±1.8° F @ 50 to 86° F (±1° C @ 10 to 30° C) Specific gravity: 0.001 Spare parts kit includes: O-ring, sample Resolution 2002/3-SPR-PRT-KIT chamber w/ rubber pump, (3) 9" sample Temperature: ±1° F (±1° C) tubes Method of Detection Light refraction system 2002/3-HOL Holster w/ belt for SBS-2002 Size & Weight 2.75" x 1.75" x 8.25"; 0.66 lbs. Suction Nozzle 9.5"L x 1/8" dia. flexible silicone tube

4 NEW! SBS-2003 Digital Hydrometer / Density Meter Digital Specific Gravity Tester with Downloading Capabilities for Lead-Acid Batteries

Specific gravity testing has never been this easy. Simply insert the nozzle into the battery and

depress the finger pump which draws a few drops of sulfuric acid (H2S04) through the tube. Within three seconds the measured refractive index is converted into a temperature-compensated specific gravity reading and then the specific gravity, temperature and cell count are displayed. Then, you have the ability to transfer the data to your PC or laptop via Bluetooth and download results into Excel. Combining a light weight and durable design with easy maintenance, field�replaceable spare parts and a large data storage memory, the SBS�2003 is suitable for use in all industrial environments.

Benefits •• Via Bluetooth, wirelessly transfers testing data to supplied Excel template •• Time savings — 5 times faster than conventional methods •• Measures specific gravity, ambient temperature and count •• Automatically temperature compensates to 77º ˚F (or 25º C) •• Stores up to 1000 readings — can export raw data to Includes Excel from template •• Main unit •• Three (3) silicone tubes •• 9V battery Data Archive/ •• Adjustable hand strap Export into Excel •• Instruction manual Features •• Case •• Exclusive to Storage Battery Systems •• Bluetooth to USB adapter •• Able to record temp in Fahrenheit or Celsius w/software template •• ±0.002 accuracy •• LED display Applications •• IP64 water resistant •• Utility •• Field calibrate with distilled water •• UPS •• For lead�acid batteries only •• Data Centers •• Telecom •• Material Handling

5 hrs Example of Cost Savings

DIGITAL HYDROMETERS DIGITAL Field studies show time savings of at least 5 times (500%) using 4 hrs a digital hydrometer over a standard glass hydrometer and thermometer. 3 hrs A time savings If you spend 60 minutes testing specific gravities every month in 2 hrs of over 500% 20 sites, this total, 60 minutes x 20 sites x 12 months per year = with the 14,400 minutes divided by 60 minutes = 240 labor hours per year. 1 hr SBS�2003 Since we can reduce this time by 500%, 240 hours divided by 5 = 0 hrs 48 hours total time with the SBS�2003. 5 Units 10 Units 15 Units 20 Units That’s a savings of 192 hours per year. Multiplied by $45.00 per hour labor cost with benefits: 192 x $45.00 Standard Glass SBS�2003 = $8,640.00 of savings per year. Hydrometer

5 www.sbsbattery.com 1-800-554-2243 [email protected] SBS-2003 Hydrometer Data Transmission

Data Transmitted (in order): Instrument Features •• Counter #### (0001 through 1000) •• Measurement •• Converted Specific Gravity #.### •• With the display on, fill the sample chamber and press and •• Temperature ##.# (in either ℉ºF or ºC℃) release the sample pump. Press the START key. The reading will be displayed on the screen, the data will be recorded, and the counter will automatically advance to the next cell #. Transmission Standard •• Bluetooth one-way transmission of •• Allows user to cancel the last reading measured data from hydrometer to PC •• Transmit Readings (via included USB adaptor if necessary). •• Data Counter Reset •• Deleting the stored data resets the counter. •• Switch between F and C

Hydrometer/Resistance Tester Package 5 Steps for Easy Data Management & Storage When combined with our SBS�6000 battery diagnostic tester, the SBS�2003 provides an all�in�one solution for your battery testing needs. 1. Save the readings from the SBS�6000 into the Battery Test Manager Software 2. Open the SBS�6000/2003 data merge worksheet. 3. Select the desired data from the History Archive (The worksheet automatically formats the workbook) 4. Download the SBS-2003 data directly into the merge worksheet SBS�2003 SBS�6000 5. Save or Print Hydrometer Battery Analyzer DIGITAL HYDROMETERS

Data merge worksheet — contains data for SBS�6000 on left with Pass or Fail status.

Hydrometer readings are added directly into the worksheet, on the right. Now, all data for each battery is in one, easy�to�read spreadsheet.

Specifications Ordering Information Specific gravity of sulfuric acid temp. compensated to 77° F (25° C) Measured Items Part No. Description Temperature of sulfuric acid as electrolyte in lead-acid batteries SBS-2003 Digital specific gravity tester (ºF and ºC) Display LCD; specific gravity, temperature, and count Measuring Time Within 3 seconds after pushing “START” button Specific gravity: 1.000 to 1.300 Accessory Ordering Information Measurement Range Temperature: 41 to 104° F (5 to 40° C) Part No. Description Measurement Specific gravity: ±0.002 @ 50 to 86° F (10 to 30° C) Accuracy Spare parts kit includes: O-ring, sample Temperature: ±1.8° F @ 50 to 86° F (±1° C @ 10 to 30° C) 2002/3-SPR-PRT-KIT chamber w/ rubber pump, (3) 9" sample Method of Detection Light refraction system tubes Size & Weight 2.75" x 1.75" x 8.25"; 0.66 lbs. 2002/3-TUBE 9" sampler tube for SBS�2003 Suction Nozzle 9.5"L x 1/8" dia. flexible silicone tube 2002/3-HOL Holster w/ belt for SBS�2003

6 SBS-2500 Digital Hydrometer / Density Meter Digital Specific Gravity Tester With Downloading Capabilities for Ni-Cad or Lead-Acid Batteries

The SBS-2500 offers the ability to test both lead-acid and nickel-cadmium batteries within seconds. Our SBS-2500 compares the temperature of the sample fluid with the set value and makes the necessary adjustments automatically with the built-in thermostat. This unit will allow you to log up to 1,100 individual S.G. and temperature readings that can later be uploaded to a laptop or PC running the included software. When combined with our SBS-6000 battery diagnostic tester, it provides an all-in-one solution for your battery testing needs. Easy instructions to follow: immerse the sampling tube, pull the trigger and view your final results. Whether in a telecommunications central office, utility substation or critical data power battery room, the ability to spot-check the specific gravity of suspect cells is invaluable. Performing some or all of your own preventative maintenance on your entire flooded battery plant is greatly simplified when employing this digital hydrometer.

Features •• Time savings — 5 times faster than conventional methods SBS-2500 Includes •• ± 0.001 accuracy •• Tests Lead-Acid and Ni-Cad batteries •• Main unit •• Measures specific gravity and temperature •• CD-ROM software package •• Automatically temperature compensated to 77º F (25º C) •• IR computer link •• Stores 1,100 results internally •• 12" sample tube / washer •• Software package for downloading •• Protective rubber boot •• Carrying case •• Carrying case •• LED display •• Instruction manual •• CE compliant

Ordering Information Part No. Description SBS-2500 Digital specific gravity tester with downloading capabilities Applications •• Battery Accessory Ordering Information •• Petroleum Part No. Description •• Food 2500-SPR-PRT-KIT Spare parts kit includes: O-ring, sample pump, (1) sample tube & washer •• Alcohol 2500-TUBE/WASH Sample tube and washer for SBS-2500

Specifications DIGITAL HYDROMETERS DIGITAL Method of Detection Specific gravity; oscillating tube method Battery Cell SBS-2500 PC/laptop Temperature User-defined temperature correction Range 0.0000 – 2.0000 Indicator High resolution dot matrix display; specific gravity, temperature Measuring time Within 3 seconds Power supply (2) AAA batteries Calibration With dry air or pure water Accuracy ±0.001 Size 9"L x 4.5"W x 2.5"H; 12.7 oz. Battery Records Printer Suction Nozzle 11.8" x 1/8" dia.

7 www.sbsbattery.com 1-800-554-2243 [email protected] SBS-3500 Digital Hydrometer / Density Meter Digital Specific Gravity Tester with Downloading Capabilities

The SBS-3500 is a portable specific gravity meter that uses oscillating U-tube technology to measure the density of your sample, supplying results within seconds. With the ability to communicate wirelessly to a printer or PC via the integrated IrDA interface, it allows you to upload specific gravity test results to the included software. This is a great solution for battery systems, general industrial, and laboratory applications.

Features •• Compact, lightweight design enabling one-hand measurement •• Extremely user-friendly menu •• Large LCD screen with backlight for clear visibility of results •• ±0.001 accuracy •• Measures specific gravity and temperature •• Wireless infrared data interface for data exchange •• Tests both Lead-Acid or Ni-Cad batteries •• Automatically temperature compensates •• Stores up to 100 sample IDs for easy sample identification DIGITAL HYDROMETERS •• Stores up to 1024 measurement results including time stamp SBS-3500 Includes and sample ID features •• Main unit •• Easy and fast replacement of the entire pump assembly •• Instruction manual •• Filling tube: 7" •• Carrying case Ordering Information •• IR computer link Part No. Description Digital specific gravity tester with Applications SBS-3500 downloading capabilities •• Battery •• Food & Beverage Processing •• Cosmetic Accessory Ordering Information •• Medical Research •• Pharmacology Part No. Description •• Electronics 3500-TUBE 7" sampling tube for SBS-3500 •• Environmental Analysis 3500-PUMP Replacement Hand Pump for SBS-3500

Specifications Method of Detection Specific gravity; Density Meter Oscillating U-Tube Technology Temperature 0° to 40° C Range 0.0000 – 3.0000 Measuring Time Within seconds Power Supply (2) AA batteries Calibration With dry air or pure water Accuracy ±0.001 Size 5.5"L x 5.4"W x 1"H SBS-3500 density meter Filling Tube 7"

8 SBS-6000 Battery Analyzer Complete Battery Resistance Testing Kit Meets All IEEE/NERC Standards

Benefits The SBS-6000 analyzer is a powerful •• Very large data storage capacity: more than handheld storage battery tester. It is a 100,000 records multi-purpose resistance and voltage •• Large 3.5" LCD color backlit display testing kit for batteries from 1.2 to 48 Vdc. •• User-friendly and easy to navigate menu The SBS-6000 transmits test data •• Meets IEEE and NERC maintenance through RS232 or RJ45 ports. recommendations for stationary battery systems Features Applications •• Tests flooded lead-acid, VRLA & Ni-Cad batteries •• Voltage testing range is 0–60V for batteries from •• Telecommunications 1.2–48 Vdc •• .Utility •• Built-in rechargeable Li-Ion battery for •• .UPS approximately 5 hours run time •• Battery manufacturing •• Automatically measures and stores data through •• Industrial maintenance contact probes on the battery posts •• Critical power •• Software package for storing and analyzing results •• Data center and creating reports

Battery resistance testing Functions •• Communicates through RS232 or RJ45 ports •• Storage battery resistance testing: automatically switches within the test range 1 mΩ to 400 mΩ Specifications and resistance measurement resolution reaches 1 mΩ Size and Weight 4.25"W x 1.97"D x 7.5"H; 2.2 lbs. •• Resistance test each connection in under 5 seconds Storage 100,000 records •• Internally stores up to 100,000 parameters Ah Measurement Range 5 - 6000Ah, 0 to 60 Vdc •• Test results are compared to user-defined alarm setpoint values Resolution: 0.001V Voltage Measurement Accuracy: ±0.1% •• Generates and displays the battery string’s single cell test report and comparison data Range: 1 mΩ to 400Ω Resistance Measurement Resolution: 0.001 mΩ •• On-screen pass / warning / fail indication during testing Accuracy: ±1.0% Display 3.5" LCD color, 320 x 240 backlit screen User Programmable Alarms, Setpoints Communication Interface RS232 serial or RJ45 Ethernet cable

INTERNAL RESISTANCE TESTER RESISTANCE INTERNAL Software Battery Manager 6000 Software Format Windows XP/7 Built-in Battery Rechargeable Li-Ion battery Operation Time More than 5 hours Operation Temperature -14° F to 122° F Built-in handle/stand

9 www.sbsbattery.com 1-800-554-2243 [email protected] SBS-6000 Includes •• Main unit •• 4 point pin probes •• Clamp probes 4 Point Pin Probes •• Li-Ion battery & charger •• Heavy duty carrying case •• RJ45 and RS232 cables •• Instruction manual •• Battery Manager 6000 software

Clamp Probes

Hydrometer/Resistance Tester Package INTERNAL RESISTANCE TESTER Easy Data Management & Storage When combined with our SBS-2003 hydrometer, the SBS�6000 provides an all�in�one solution for your battery testing needs. See the SBS-2003 data sheet for more information.

SBS�2003 SBS�6000 Hydrometer Battery Analyzer

Battery Manager 6000 Software •• Analyzes battery function and efficiency •• Interface for loading string and alarm data to and from tester •• Direct export into Excel format for easy incorporation into custom reports •• Separate data archives for cell, battery, and intercell connector resistance records •• Self interpretation of data for clear, concise comparisons Track changes in battery resistance and battery deterioration trend

Ordering Information Accessory Ordering Information Part No. Description Part No. Description SBS-6000 Complete battery resistance testing kit 6000-CLAMP-PROBE Extra clamp probe leads 6000-PIN-PROBE Extra 4 point pin probe leads 6000-PIN Replacement pin for 6000-PIN-PROBE leads 6000-BATT Spare Li-Ion battery for SBS-6000

10 SBS-8400 Battery Capacity Tester with Monitoring 10–300 Vdc, 0–120 Amp Constant Current Load Bank with Wireless Data Logging

The SBS-8400 was designed as an improved version of the popular Torkel 840™ load tester. The SBS-8400 has similar discharging capabilities as the Megger Torkel 840™*, however it has the advantage of having a user-friendly touch screen menu and a built-in data monitoring/acquisition system complete with wireless modules and software.

Benefits •• Wireless modules are easy to hook up and eliminate hundreds of feet of signal wire •• Each module can record the real-time voltage of up to four individual cells or multi- cell blocks •• While testing, real-time data is visible on unit’s 5.7" color screen or through a laptop •• Unique because it has adjustable, automatic stop points - the unit can automatically stop the test if a cell or entire string falls below a user-set voltage •• Settings can be changed during a discharge test (current, stop time, stop voltage, etc.) without stopping the test •• Safety - tests can be done without a technician on site and without danger of over- discharging an individual cell or the entire system •• Download test results via USB flash drive and export reports, including individual cell voltages and graphs

Features •• Wide voltage and current range: 10-300 Vdc / 0-120 Amps •• Can be paralleled with other load bank to increase draw up to 600 Amps (optional 600 Amp DC clamp required for monitoring) •• 5.7 in. LCD touch screen for easy operation •• View test data in real time on screen or with laptop via RS232 •• Selectable discharge mode: constant current/power/resistance •• 4 adjustable stop points and multiple alarm designs to control the discharge process intelligently • Low system voltage: 0-250 Vdc • Discharge time: 0-99 Hour 99 Min Online monitoring function • Discharge capacity: 0-9999 Ah • Low cell voltage: 0-15.00 V •• Download data after discharge to USB drive •• PC software for capacity evaluation and report generation DC LOAD BANKS Applications •• Telecommunications •• .Utility •• .UPS •• Battery manufacturing •• Industrial maintenance •• Critical power •• Data center

Example of how the wireless modules would be installed on a 48 Vdc system consisting of qty. (24) 2 volt cells

*SBS is not related to, or affiliated with, Megger or the Torkel 840™ unit. 11 www.sbsbattery.com 1-800-554-2243 [email protected] Specifications DC Volt Range 10-300 Vdc Includes 10-15 / 150-300 Vdc: 0-60 Amps DC Current Range •• Main unit 15-150 Vdc: 0-120 Amps •• 6 ft DC cable set (pos & neg) Accuracy & Resolution ±1.0%, 0.1 Amp •• 3 ft AC cable Display 5.7" LCD Color Touch Screen •• RS232 wire Power Supply 110 Vac, 60 Hz •• 2GB USB disk Communications Port USB / RS232 •• Case for main unit Internal Memory 8MB Flash •• Software •• Instruction manual Size (main unit) 9.1" x 14.6" x 26.4"; 53 lbs. Portable packing case included Size (with case/acc.) 11.1" x 25.2" x 29.6"; 93 lbs.

Software The SBS-8400 utilizes a highly analytical software interface that allows for custom programming of discharge parameters. Its versatile user-interface makes set up and operation of tests an easy task with very little operator action required. Powerful analysis software collects discharge data and stores it, where it can then be generated into a variety of customized reports. Unlike basic load banks, the SBS-8400 is a high-tech solution to easy, efficient collection of data and generation of records for archiving. BANKS LOAD DC

DC Clamp Paralleling Load Banks The SBS-8400 has a 0-120amp current range; however it is possible to parallel additional load banks (almost all models will work) with the SBS-8400 to increase the current. With the optional P/N 8400-600A DC clamp the user can discharge up to 600 amps and the SBS-8400 will monitor the total DC current being drawn by both load banks combined.

Accessory Ordering Information Part No. Description 1.2/2V Wireless module kit w/ case MODULE-1.2/2-25 Qty. 25 (+2 spare)* 1.2/2V Wireless module kit w/ case MODULE-1.2/2-30 Qty. 30 (+2 spare)* SBS-8400 Slave load bank 2/6/12 Wireless module kit w/ case MODULE-2/6/12-15 Qty. 15 (+2 spare)* 2/6/12 Wireless module kit w/ case MODULE-2/6/12-30 Qty. 30 (+2 spare)* 8400-600A 600 DC Current Clamp Ordering Information BCT110/220 - 1000 1000 Watt Voltage Transformer 110/220 Part No. Description Vac 50/60 Hz For operating in parallel with load banks SBS-8400 0–300 Vdc, 0–120 Amp load bank 8400-SLAVE-CABLE of same voltage range *module details on page 14 12 SBS Wireless Modules Battery Voltage Logger (Accessory for SBS-8400 Battery Discharger / Capacity Tester)

The SBS wireless modules are a battery voltage measurement kit used in conjunction with the SBS-8400. During capacity testing, they measure each battery’s voltage and wirelessly send the data back to the SBS-8400. All voltage values are displayed on the SBS-8400 LCD screen and listed in the test report which is created with the PC software. You can then locate the failed batteries in the battery bank and estimate the actual capacity of each battery.

Features •• Real-time battery voltage measuring during discharge test •• Wireless communication between modules and load bank •• Wide range for 1.2/2/6/12V batteries •• One module supports voltage measurements for 4 batteries •• Supports monitoring up to 120 batteries in a single test (for testing strings in parallel)

Connection Each wireless module can connect to 4 cells or batteries. The SBS-8400 can work with up to 30 modules (monitoring 120 batteries) in single capacity test. Wireless communication makes connecting the modules to the batteries very convenient and time-saving. WIRELESS MODULES

Voltage bar chart on SBS-8400 LCD Voltage bar chart in PC Software

13 www.sbsbattery.com 1-800-554-2243 [email protected] Specifications Type Module-2V/6V/12V Module-1.2V/2V

Support Cell Voltage 2V/6V/12V 1.2V/2V Wires Six (1 Red, 1 Black, 4 Yellow) Five (4 Red, 1 Black) Red & Black Red No. 1 & Black Power Supply Wire Operating Voltage: 5V - 24V Operating Voltage: 3.5V - 20V Max. Voltage: <400V Max. Voltage: <60V Measure Voltage Range 0-16V for each channel 0-5V for each channel Accuracy & Resolution ≤±0.5%, 0.01 V ≤±0.5%, 0.01 V Default Frequency 433.0 MHz 433.0 MHz Connection Drawings WIRELESS MODULES WIRELESS

Weight 0.66 lbs. (0.3 kg) Dimensions 3.9 x 2.6 x 1.3 in. (100 x 65 x 32 mm) Operation Temperature 23° to 122° F (-5° to 50° C) Storage Temperature -40° to 158° F (-40° to 70° C) Humidity 5% - 95% RH Altitude below 13,100 ft. (below 4000 m)

Wireless Load Bank Module Kits Ordering Information DC Voltages of Systems Module Package(s) Qty. of Modules Battery Type to be Tested Required (Part No.) (+2 spares) 12 - 125 Vdc MODULE-2/6/12-15 15 Lead Acid Only (2, 6, 12V) 12 - 250 Vdc MODULE-2/6/12-30 30 12 - 125 Vdc MODULE-1.2/2-25 25 Ni-Cd / Single Cell Lead Acid Only (1.2/2V) 12 - 250 Vdc MODULE-1.2/2-30 30

14 Constant Current DC Load Banks For Discharge Testing 24 – 250 Vdc Battery Systems

The only way to know your stationary batteries will perform to specification is to test them regularly. NERC standard PRC-005-2 requires that Vented Lead-Acid and Features Nickel Cadmium systems be discharge tested every six years and Valve •• Constant current load bank holds the current set Regulated Lead-Acid (VRLA) batteries be tested every three years. throughout the test IEEE recommends load testing stationary flooded/vented lead-acid and •• LED screen displays real time voltage, discharge Ni-Cad stationary batteries every 5 years and VRLA batteries every current and Ah removed 12-18 months. •• Units can be paralleled with the SBS-8400 or The SBS constant current load banks are an affordable way to perform other load banks easy and accurate IEEE450 (Vented Lead-Acid), IEEE1106 (Ni-Cad) and •• Easily adjust settings electronically IEEE1188 (VRLA) load tests. •• 3 adjustable stop points These units are quick and easy to set up. They display the voltage, • End system voltage current and Ah removed during the test. Since this is a constant current • Discharge time load bank, the user also does not have to constantly adjust the current • Discharge capacity (Ah) during the test like many other load banks. These load banks come standard with multiple auto-stop settings and built-in protection to ensure that the batteries are never damaged due to over discharge.

LCD screen

Control buttons

Power switch

Parallel installation socket DC LOAD BANKS

External current measurement socket Built-in Protection •• Audible alarm •• Warning on LED screen •• High temperature shutdown Cooling fans •• High voltage shutdown •• Over load protection

SBS-4830S DC power cable sockets Includes •• Carrying case •• 9 ft DC cables •• Instruction manual

15 www.sbsbattery.com 1-800-554-2243 [email protected] Constant Current DC Load Banks (cont.) For Discharge Testing 24 – 250 Vdc Battery Systems

A load bank can be paralleled with another load bank (of the same unit, or the SBS-8400) to increase draw up to 600 Amps. Optional 600Amp DC clamp is required for monitoring.

DC Clamp Slave Cable P/N 8400-600A P/N 8400-SLAVE-CABLE

SBS-1110S DC LOAD BANKS LOAD DC SBS-1110S SBS-1110S

Technical Data Display LCD (128 x 64 pixels) During discharge: real time voltage / current / test time / Ah discharged Input User can set: end system voltage / test time / capacity discharged (Ah) Test Type Unit controls the current so it stays where it is set throughout the test Protection Over heat / Over load / Over voltage protection with audible alarm and screen warning SBS-4830S uses DC power supply (from tested battery) Power Supply 125 and 250 Vdc units use AC power supply (110 Vac 60 Hz) DC Cables Included - 9 ft long

Specifications Ordering Information DC Current Dimensions Part No. Description Part No. DC Voltage Range L x W x H Weight Range (Amps) (in.) (lbs.) 24 Vdc 0–150 Amp / 48 Vdc 0–300 Amp SBS-4830S Constant Current Load Bank 20-40 Vdc 0-150A SBS-4830S 26 x 9 x 16 40 SBS-1110S 125 Vdc 0-100Amp Constant Current Load Bank 40-60 Vdc 0-300A SBS-1230S 125 Vdc 0-300Amp Constant Current Load Bank SBS-1110S 90-150 Vdc 0-100A 25 x 9 x 15 44 SBS-2206S 250 Vdc 0-60Amp Constant Current Load Bank SBS-1230S 90-150 Vdc 0-300A 36 x 9 x 25 110 SBS-2415S 250 Vdc 0-150Amp Constant Current Load Bank SBS-2206S 190-265 Vdc 0-60A 26 x 9 x 16 40 SBS-2415S 196-300 Vdc 0-150A 36 x 9 x 25 110

16 SBS-4815CT Mini Battery Discharge / Capacity Tester For 24/48 Vdc Battery Systems

The SBS-4815CT is a fully programmable, constant current discharge load bank with detailed data acquisition and display capabilities. Built-in memory continuously records discharge data.

Features •• Provides 0–150A adjustable current for different load testing requirements and performs constant current discharges while testing •• 5.7 in. LCD touch screen for easy operation display of various parameters in real time •• 4 programmable stop points and multiple alarm settings to control the discharge automatically Applications •• Supports RS-232 real time monitoring with a PC or stores data internally for later •• Telecom transfer via a USB device •• Forklifts, Golf Carts & AGVs •• PC software included for detailed analysis of test results and generation of reports •• Power Plants & Oil Companies •• Wireless modules included for individual cell data collection during testing •• Can be powered from DC or AC power supply

Internal Memory •• Saves each test result automatically and protects data from unexpected termination of test •• Menu interface provides data management operations like test results review, deleting or downloading of results by RS-232 or USB device to the PC software

Analytical Software •• Powerful analytical software calculates test results and reports battery cell conditions and capacity DC LOAD BANKS •• Software interface displays detailed graphs and carts for all battery test data •• Features the ability to export raw data into Excel for the creation of customized reports

Preset Feature •• Can be programmed with up to 8 sets of test parameters, speeding up test setup and performance Adjustable test stop points to prevent excessive discharge Discharge Ranges Stop Point Setting Range Voltage Range Current Range Low System Voltage 0 - 60.0 V 20 - 40V 0-75A Discharge Time 0 - 99 Hour 99 Min. 40 - 60V 0-150A Cell Low Voltage 0 - 15.00 V

17 www.sbsbattery.com 1-800-554-2243 [email protected] Malfunction LCD Prompt Warning Beep Input Over Voltage   Reverse Polarity   Overload   Overheat  

Wireless Modules •• Wireless modules are included for collection of Parallel Operation individual cell/battery voltage data during discharge •• Incorporation of the Current Clamp accessory allows •• For 2V, 6V or 12V batteries (Optional 1.2V Ni-Cd the SBS-4815CT to be operated in parallel with other modules available) load banks of the same voltage range •• Each module is capable of monitoring up to 4 cells/ •• This allows for increasing the total discharge current batteries at a time capacity that can be monitored by the unit for larger •• Wireless technology eliminates having hundreds of feet AH rated batteries of signal cables lying underfoot while performing testing

Includes Specifications Current Measurement:

•• Main unit BANKS LOAD DC •• Wireless modules (qty. 6 +1 spare) Internal Current Range 0-150A •• PC analysis software Accuracy & Resolution

The SBS-200CT is a discharge cycler for batteries’ discharge and charge cycle. The voltage range of 2V – 96V covers all types of traction batteries (stationary, forklifts, automobile, golf cart, train, wheel chair, etc.). When equipped with an industrial charger (sold separately), the SBS-200CT can provide an unmanned discharge/ cycling solution for your material handling needs.

Features •• Wide voltage range battery discharge from 2V to 96V •• Automatically run multiple discharge/charge cycles •• 5.7 inch LCD touch screen for easy operation and showing various parameters real time •• Adjustable stop points and multiple alarm designs to control the discharge and charge process intelligently •• Supports RS232 real time monitoring by PC or USB download data after discharge •• PC software for capacity evaluation and report generation •• Can be used to test overall system voltage and individual cell voltages •• Wireless modules included (up to 40 cells) with other module package options available

Standalone Discharge

PC Analysis Software •• Data downloading and analyzing through real-time communication or USB memory devices •• The software interface includes: battery voltages curve and bar Or, use with any charger to automatically cycle the battery: chart, battery resistances bar chart, group voltage curve, current curve, capacities histogram, data form, etc. •• Powerful capacity estimating function; the software can predict Cycle the capacity of each battery in the tested group •• Automatically create Excel data report

Test Range Can support 2-96V battery groups;

Battery Nominal Voltage Max Discharge Current 2 V 60A

BATTERY DISCHARGE CYCLER BATTERY 4 V 120A 6/24 V 180A The SBS-200CT discharger will cycle through the 12/36/48 V 200A charge and discharge cycles of the batteries multiple times while recording cell data unattended. 72/80/96 V 200A

19 www.sbsbattery.com 1-800-554-2243 [email protected] Includes •• Main unit •• Wireless modules (qty. 10 +1 spare) •• PC analysis software •• DC test (power) cables Wireless Modules •• Instruction manual •• Wireless modules are included for collection of •• Carrying case Portable packing case included individual cell/battery voltage data during discharge •• For 2V, 6V or 12V batteries (Optional 1.2V Ni-Cd modules available) •• Each module is capable of monitoring up to 4 cells/ batteries at a time •• Wireless technology eliminates having hundreds of feet of signal cables lying underfoot while performing testing Specifications Current Measurement: Internal Current Range 0-200A Accuracy & Resolution

Discharge Ranges BATTERY CYCLER DISCHARGE External Current Range 0-600A (optional current clamp) Voltage Range Current Range Accuracy & Resolution

For operating in parallel with load banks Weight 121 lbs. (main tester only) 8400-SLAVE-CABLE of same voltage range 220 lbs. (tester, accessories, case)

For additional specifications and model details, please contact a Storage Battery Systems representative.

20 SBS-600 Graphical Digital Multimeter with USB PC Interface High Accuracy True RMS Digital Multimeter and Data Logger with Trend Analysis

The SBS-600 is an industrial graphical digital multimeter and data logger with trend analysis. It will quickly capture data with real-time logging and graphing capabilities and can store up to 10,000 readings with recall ability. This unit has a large, 50,000 count, 3.5" high resolution display with the ability to zoom on trends to view and analyze captured data. This means you don’t need to download the readings to a laptop or PC to detect a trend or recall past readings. PC integration software is included so you can download readings into the provided software or export to Excel.

Benefits •• 600V CAT III DMM / 1000V CAT IV Safety Rating •• Next generation, high performance, graphical digital multimeter •• Large 50,000 count, 3.5" high resolution LCD displays DC Voltage, True RMS AC V •• Efficiency measurement and ripple noise measurement •• Includes real-time PC connection/logging •• Multiple logging sessions possible without download

Power Efficiency Measurement •• Automatically displays efficiency without having to manually calculate •• Measures all power circuit efficiencies, including DC to DC converter and total instrument efficiency readouts •• Range for DC Voltage: 50mV ~ 1000V, DC Current: 500µA ~ 10A

Dual Mode Measurement (Ripple Noise Measurement) •• Measures ripple noise under 100 kHz •• DC voltage and AC voltage measurements displays separately from AC+DC measurement function •• Measures DC voltage and AC voltage in order •• DC voltage measurement range: 5V ~500mV •• Ripple noise frequency displays simultaneously

Data Logger with Trend Analysis •• Plots up to 10,000 recorded readings •• Man-Free Monitoring as well as Trend Capture and Analysis •• The data logger plots at real time stamping •• Internal storage memory can store up to 10,000 records and instantly recall •• Trend Capture and Trend Analysis are available from Complete Mode (Run/Stop, sampling time, accumulated sample qty, measured value scale (max)) GRAPHICAL MULTIMETER DIGITAL

Multimeter data logging screen shot Voltage data logging screen shot Resistance logging screen shot

21 www.sbsbattery.com 1-800-554-2243 [email protected] Technical Data DC/AC Voltage Range 50.000mV 500.00mV 5.0000V 50.000V 500.00V 1000.0V Accuracy 50mV (±0.05%+50) 500mV-50V (±0.025%+10) 500V-1000V (±0.030%+10) DC/AC Current Range 500.00µA 5.0000mA 50.000mA 500.00mA 10.000A Accuracy 500mA-5.0000mA (±0.05%+10) 50mA-500mA (±0.15%+10) 10A (±0.30%+10) Temperature (excluding probe) (-20.0° ~ 500.0° C, -20.0° ~ 1370.0° C) or (-4.0° ~ 500.0° F, -4.0° ~ 2498.0° F) Accuracy Dependent on optional temperature probe Resistance 50.000Ω 500.00Ω 5.0000kΩ 50.000kΩ 500.00kΩ 5.0000MΩ 50.000MΩ Accuracy 50Ω-500kΩ (±0.05% +10) 5MΩ (±0.15% +10) 50MΩ (±1.00% +10) Capacitance 5.0000nF 50.00nF 500.0nF 5.000uF 50.00uF 500.0uF 5.000mF Accuracy (±1% +10) > 50.00uF (±2% +10) Frequency 10.00Hz 100.0Hz 1kHz 10kHz 100kHz 1000kHz Accuracy 0.005% SBS-600 Fluke® 287* Fluke® 289* Multiple On-Screen Displays Yes Yes Yes dBV/dBm Yes Yes Yes DC mV Resolution 1 uV 1 uV 1 uV Megaohm Range Up to 500 MΩ Up to 500 MΩ Up to 500 MΩ Continuity Beep Yes Yes Yes Battery/Fuse Access Battery/Fuse Battery/Fuse Battery/Fuse Elapses Time Clock Real Time PC connection/logging Yes Yes Time of Day Clock Real Time PC connection/logging Yes Yes Min-Max-Avg Yes Yes Yes Duty Cycle 0.05 to 95.00% 0.01 to 99.99% 0.01 to 99.99%

Hold Yes Yes Yes DIGITAL MULTIMETERGRAPHICAL Decibels Yes No Yes Isolated Optical Input USB to PC Yes Yes Auto Touch/Hold Yes Yes Yes Reading Memory Yes Yes Yes Log to PC Yes Yes Yes Interval/Event Logging Yes Yes Yes Logging Memory 10,000 readings 10,000 readings 15,000 readings

SBS-600 Package Includes •• Main body/display Optional test lead •• Pinpoint probes accessory kit •• Software/USB cable •• Batteries •• Quick start guide

Specifications Maximum Voltage Terminal to Earth Ground 1000 Vac Battery Type 6 AA alkaline batteries Ordering Information Battery Life 80 hours continuous without backlight Part No. Description Digital multimeter with data logging Operating Temperature 32° F to 122° F SBS-600 and software Storage Temperature 32° F to 158° F Humidity 80% RH or less (non condensing) Accessory Ordering Information Dimensions 3.9" W x 8.6" H x 2.1" D Part No. Description Weight 20 oz. / 1.2 lbs. (meter only) 600/700-TEST-LEAD-KT Test lead accessory kit Display 3.5" 240 x 160 pixel graphic mono LCD 600/700-CASE Case for multimeter *SBS is not related to, or affiliated with, Fluke® or the Fluke® 287 or 289 units. Fluke® is a registered trademark and Fluke® 287/289 are trademarks of Fluke® or its subsidiaries. 22 SBS-700 Multi-Function Oscilloscope/Multimeter Oscilloscope and Digital Multimeter Including Data-Logging PC Software

The SBS-700 scope/meter helps minimize your project risk by providing reliable, accurate data or waveform capture and the complete view of Logic Tools. This comprehensive unit offers a highly accurate multimeter measurement function and additional function on Sig‑Out (Generator), Digital Debug (Logic, Serial Bus Protocol with Digital Pattern Generator). This unit includes a case and USB PC Integration software so that you can download your readings into your PC. You can also recall readings and graphs directly from the unit.

Oscilloscope Benefits •• 10 MHz bandwidth with max. 50 MS/s real •• 600 V CAT III & 1000 V CAT IV DMM / sampling rate 300 V CAT III O-Scope •• AC/DC coupling •• Large 50,000 count, 3.5” high resolution •• Wide direct input voltage – up to 100V/div in LCD, displays DC Voltage, True RMS AC V 1,2,5 steps •• Efficiency measurement and •• Multiple advanced programmable trigger modes ripple noise measurement •• Advanced auto-set functions automatically catch •• Includes real-time PC connection/logging and display waveform •• Multiple logging sessions possible without download

Graphical Digital Multimeter •• 50,000 count True RMS 3.5" high resolution display DC V, True RMS AC V, AC+ DC V, DC A, True RMS AC A •• Volts, currents, frequency, resistors, capacitance, diode, continuity, frequency - duty cycle - pulse width, signal out generation, dBm •• Temp., humidity, hi-current, pressure measurement through AUX (external adapters not included) •• Min/max, autorange, (manual) hold, auto hold, peak hold, bar graph display, REL, warning mode, simultaneous multiple display: present measurement, min/max/avg/dBm in real-time stamping Multimeter Data Logging Oscilloscope - Peak Detection Mode

Logic Analyzer Achieve the fastest logic analyzer control and analysis to maximize your analyzer’s usage. Sets up measurements quickly and easily. •• 8 input channels supported •• Sample rate: maximum 50 MHz per channel •• Peak detection and time measurements supported •• Trigger mode: pattern and duration supported Logic Analyzer - Duration Trigger Logic Analyzer - Pattern Trigger

Protocol Analyzer Digital Pattern Generator •• Sample Rate: maximum 50 MHz per channel An essential feature for digital system development. Digital pattern is automatically

OSCILLOSCOPE / MULTIMETER OSCILLOSCOPE •• Peak detection and time measurements supported displayed on protocol analyzer screen without connecting with the oscilloscope. •• Trigger Mode: CAN, LIN, I2C, UART, USB (low/full •• 2 channels (TX, RX) supported speed), I2S, SMBus, SPI, DMX512, 1-Wire supported •• Baud rate: up to 1 Mbps •• Supports trigger condition setup and speed selection •• Pattern format: UART, CAN, and user defined if needed •• Supports making and storage of up to 8 patterns including information like interval, repetition and idle condition •• Monitoring mode supported for watching pattern waveform or data transaction

23 www.sbsbattery.com 1-800-554-2243 [email protected] Technical Data DC/AC Voltage Ranges 50.000mV 500.00mV 5.0000V 50.000V 500.00V 1000.0V Accuracy 50mV (±0.05% +50) 500mV-50V (±0.025% +10) 500V-1000V (±0.030% +10) DC/AC Current Ranges 500.00µA 5.0000mA 50.000mA 500.00mA 10.000A Accuracy 500µA-5.0000mA (±0.05% +10) 50mA-500mA (±0.15% +10) 10A (±0.30% +10) Temperature (excluding probe) (-20.0° ~ 500.0° C, -20.0° ~ 1370.0° C) or (-4.0° ~ 500.0° F, -4.0° ~ 2498.0° F) Accuracy Dependent on optional temperature probe Resistance 50.000Ω 500.00Ω 5.0000kΩ 50.000kΩ 500.00kΩ 5.0000MΩ 50.000MΩ Accuracy 50Ω-500kΩ (±0.05% +10) 5MΩ (±0.15% +10) 50MΩ (±1.00% +10) Capacitance 5.0000nF 50.00nF 500.0nF 5.000uF 50.00uF 500.0uF 5.000mF Accuracy (±1% +10) > 50.00uF (±2% +10) Frequency 10.00Hz 100.0Hz 1kHz 10kHz 100kHz 1000kHz Accuracy 0.005% SBS-700 Fluke® 123* Display 9.5 cm 50,000 count 240 x 160 pixel FSTN 10.2 cm monochrome LCD Bandwidth 10 MHz 20 MHz Number of Inputs 1 2 True-RMS Multimeter 5000 counts DDM Dual fully featured 5000 counts DDM Dual Input Trend Plot Single Input Trend Plot Yes Safety Certified EN6101-1 600 V CAT III DMM 300V CAT III O-Scope 600 V CAT III Battery (Installed) 8 hours (7.2V NiMH) 7 hours NiMH PC and Printer Interface USB Optional USB or RS-232 VDC, VAC, VAC+VDC, OHMS, Amps AC, Amps DC, Hz, Continuity, Diode, Capacitance, F/C, VDC, VAC, VAC+VDC,Ohms,Continuity,Diode test, OSCILLOSCOPE / MULTIMETER Input True RMS Meter dBV, dBM, 8 Channel Logic, 8 Channel Protocol, C, F, Capacitance, dBV, dBM,Crest Factor,Touch Pattern Hold and Zero Set Automatic Vertical Scaling and time compression Trend Plot Recording Automatic; Displays Pk-Pk, Mean, +Width and Hz Displays the actual Min, Max, Avg Readings Real Time Sample 50 MS/s 25 MS/s Time Base Range 100 ns - 50 sec/Division 10 ns - 1 min/Division Input Sensitivity 20 mV to 100 V/Division 5 mV to 500 V/Division Auto/Normal / Single, Edge / Pulse, Rising / Connect & View, Free Run, Single Shot, Edge, Trigger Types Falling / Alternate Video, External Scope Measurements Automatic Automatic measurements: On top

SBS-700 Package Includes •• Main body/display •• Carrying case Optional test lead •• Pinpoint probes accessory kit •• Software/USB cable •• Quick start guide •• AC adaptor

Specifications Maximum Voltage Terminal to Earth Ground 1000 Vac Battery Type 7.2V rechargeable NiMH battery pack Ordering Information Battery Life 80 hours continuous without backlight Part No. Description Operating Temperature 32° F to 122° F SBS-700 Multi-function oscilloscope meter Storage Temperature 32° F to 158° F Humidity 80% RH or less (non condensing) Accessory Ordering Information Dimensions 3.9" W x 8.6" H x 2.1" D Part No. Description Weight 20 oz. / 1.2 lbs. (meter only) 600/700-TEST-LEAD-KT Test lead accessory kit

*SBS is not related to, or affiliated with, Fluke® or the Fluke® 123 unit. Fluke® is a registered trademark and Fluke® 123 is a trademark of Fluke® or its subsidiaries. 24 Rev. 07-14