LAWN and GARDEN GREENHOUSE with Heavy Duty Aluminium Frame Let'sgrow Together!

MODEL# OGAL-466

OGrow Walk-in 6' x 4' LAWN AND GARDEN GREENHOUSE With Heavy Duty Aluminium Frame Let'sGrow Together!

Thank you for purchasing the OGROW™ greenhouse

Follow the assembly and safety instructions in this manual. If you have any questions, please contact our Customer Service Department

• Parts List...... 3-4 • Side Walls...... 8 • Back Wall...... 10 • Front Wall...... 12 • Door Frame...... 14 • Roof and Full Structure...... 15 • The Door...... 17 • The Vents...... 19 • The Panels...... 21

PAGE 2 PARTS LIST

PART# PART NAME PART QTY. PART# PART NAME PART QTY. IMAGE IMAGE

1 Corner Beam 4 17 Front Floor Bar 1

2 Front Right Roof Beam 1 18 Vent Stopper 4

3 Front Left Roof Beam 1 19 Vertical Door Rail Support 1

4 Rear Right Roof Beam 1 20 Left Door Support 1

5 Rear Left Roof Beam 1 21 Rear Horizontal Support 1

6 Right Doorway Support 1 22 Diagonal Support 4

7 Left Doorway Support 1 23 Front Horizontal Support 2

8 Rear Support Pole- Left 1 24 Top Door Bar 1

9 Rear Support Pole- Right 1 25 Front Diagonal Support 2

10 Side Support Pole 2 26 Center Door Bar 2

11 Roof Support Pole 2 27 Bottom Door Bar 1

12 Top Doorway Beam 1 28 Right Door Support 1

13 Corner Bracket 4 30 Vent Side Bar 4

14 Door Rail 1 31 Door Slider 1 (Including Rollers)

15 Vent Support Bar 2 32 Vent Bottom Bar 2

16 Rear Floor Bar 1 33 Vent Top Bar 2

PAGE 3 PARTS LIST

PART# PART NAME PART QTY. PART# PART NAME PART QTY. IMAGE IMAGE

34 Side Floor Bar 2 45 Vent Screw 12

35 Top Roof Bar 1 46 Panel Clip 92

36 Gutter Bar 2 47 Beam End Cap 8

38 Long Door Support Bolt 1 48 Gutter End Cap 4

39 Door Frame Spacer 1 49 Rail End Cap- Right 1

41 Spanner Wrench 2 50 Rail End Cap- Left 1

42 Rubber Seal 2 51 Vent Brace 2

43 Bolt 81 52 Nut 82

44 Door Screw 16 A-I Polycarbonate Panel 19 (See page 21)

PAGE 4 NOTICE:

Read the entire IMPORTANT SAFETY INFORMATION section ! at the beginning of this document – including all text under subheadings – before set up or use of this product.

PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. KEEP THEM IN A SAFE PLACE WHERE YOU CAN REFER TO THEM AS NEEDED. The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The user must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the user.

IMPORTANT SAFETY INFORMATION

Assembly/Installation Precautions 1. Assemble only according to these instructions. Improper assembly can create hazards. 2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly. We recommend that two people together assemble the greenhouse for a smooth and efficient assembly. 3. This unit contains pieces with sharp edges. The machined edges of the aluminium parts and the ends of the panel clips may be sharp. Handle all parts carefully. 4. Keep assembly area clean and well lit. 5. Keep bystanders out of the area during assembly. 6. Do not assemble when tired or when under the influence of alcohol, drugs or medication. 8. Build the Greenhouse on a flat and level surface. A concrete foundation is recommended for a high-quality installation. 9. WARNING: The brass bushings inside the Rollers of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety Code § 25249.5, et seq.)

Use/Service Precautions 1. This product is not a toy. Do not allow children to play in or climb on this product. Although this greenhouse does include protective covers, there are still some exposed sharp edges. In addi- tion, protective covers may fall off over time. Children must be supervised if allowed near the greenhouse. 2. SNOW/DEBRIS ACCUMULATION HAZARD. The heavy weight of accumulated snow or other debris can cause parts of this greenhouse to buckle suddenly. Do not allow debris to accumulate on top of the greenhouse. If snowfall is expected, place additional supports (not provided) under- neath the Crown (35). NEVER enter a greenhouse with accumulated debris on top. 3. Use as intended only. The product capabilities only apply to a properly and completely assembled product. 4. Inspect periodically; replace damaged parts immediately and do not enter greenhouse if parts are loose or damaged. PAGE 5 STARTING TO BUILD

IMPORTANT:

! READ THE FOLLOWING CAREFULLY BEFORE PROCEEDING:

• Before you assemble this greenhouse, you must build a proper foundation. You may use your own base of bricks, concrete blocks or treated wood. Whatever foundation you use, ensure that it is square – by checking that its diagonal measurements are equal – and level, and that the greenhouse is fastened to it securely. If you have made your own base, you will need to drill through the sill of the greenhouse. Your greenhouse needs the proper support of a foundation to help prevent property damage and injury in the event of strong winds or inclement weather. Wind and ground conditions vary from site to site, and the characteristics of your site may affect the practicality and effectiveness of anchoring methods substantially. If you have any doubt regarding the stability of the foundation you are to use, consult a professional. • It is always your responsibility to ensure that the greenhouse is properly anchored. Ogrow cannot be held responsible for personal injury, damage to the greenhouse, or other property damage that occurs as a result of improperly anchoring the greenhouse. • Check with local authorities to obtain all required building permits and to familiarize yourself with any building codes that may apply. • Decide on a location for the greenhouse. The location should optimally be a level, well lit area that is sheltered from the wind and free of overhanging branches. The door of the greenhouse should not open towards the prevailing wind, if possible. Try to locate your greenhouse near a convenient water source to aid you in watering your plants daily. Also, try to build your greenhouse in a location where the soil drains easily so that the greenhouse floor is pleasant to work on.

PAGE 6 GETTING READY

Construct a base first so that the greenhouse can be immediately mounted and secured when it is completed

Find someone to assist you in the assembly. The work is light and should suit any able-bodied person, who can speed up and ease assembly by assisting you.

Note that the construction takes time. Work slowly and methodically so that assembly is more accurate and with fewer errors; rushing only leads to needing to undo and repeat steps done erroneously. If this is your first time building a greenhouse it may take a good chunk of a day to complete the construction properly.

Prepare the tools you will need:

• A Drill • A Screwdriver • A Spanner – Part 41

Lay out all the greenhouse parts around the base to ensure that nothing is missing. (See image below.) If any parts are missing, contact us at once so that we can send you the missing parts right away.

VENTS BACK WALL ROOF DOOR

SIDE WALL FRONT WALL SIDE WALL

When you assemble the greenhouse, secure parts loosely where possible and then tighten only when everything is in place. This allows for easy minor adjustments during construction.

PAGE 7 ASSEMBLING THE GREENHOUSE

PART 1 – SIDE WALLS

Lay out all the parts needed for the side wall, following the layout shown below. The grooves in the support poles should be facing you. The oor bar and gutter bar should be perpendicular to the oor, with the wider end at the top.

Part# Part Name Part Image Qty.

10 Side Support Pole 2 22 Diagonal Support 2 34 Side Floor Bar 2 36 Gutter Bar 2 43 Bolt 10 52 Nut 10

36 STEP STEP 5 4 22 10

STEP 6

STEP STEP 2 3

PAGE 8 Follow the steps below to assemble the Side Walls.

NOTE:

Each step applies to both relevant wall supports.

10 22 43 52 43 52

34 34

STEP STEP STEP 1 10 2 3

Slide three bolts into the groove of Bolt the support poles to the Bolt the bottom of the diagonal the support poles part 10. outside of the floor bar. support poles to the inside of the floor bar.

22 10

36 36

43 52 43 52 43 52

STEP 10 STEP 22 STEP 4 5 6

Bolt the top of the side support Bolt the top of the diagonal Use the extra bolt in the outer poles to the outside of the gutter support poles to the inside of the support poles to attach the bar. gutter bar. diagonal support pole across the outer support poles.

Repeat the above steps to make the second side wall.

PAGE 9 ASSEMBLING THE GREENHOUSE

PART 2 – BACK WALL

Lay out all the parts needed for the back wall, following the layout shown below. Make sure that the roof beams are on the correct sides as the left and right di er; the grooves in the support poles are facing you; and that the oor bar is perpendicular to the oor, with the wider end at the top.

Part# Part Name Part Image Qty.

1 Corner Beam 2 4 Rear Right Roof Beam 1 5 Rear Left Roof Beam 1 8 Rear Support Pole- Left 1 9 Rear Support Pole- Right 1 13 Corner Bracket 2 21 Rear Horizontal Support 1 22 Diagonal Support 2 43 Bolt 16 52 Nut 16

STEP 05 STEP

13 6 04 4

21 13 STEP 22 1 & 5

22 1 8 9 STEP 1 STEP 3 2

PAGE 10 Follow the steps below to assemble the Back Wall.

NOTE:

Each step applies to both relevant corners/supports.

04 8 22 1

43 52 16 16 01 13 43 52 43 52 STEP STEP STEP 1 2 3

Attach the corner brackets to the Bolt the floor bar to the inside of Secure the support poles to the corner and roof beams. Lay the the corner beams, securing at outer side of the floor bar. Attach the bracket above the two beams and each corner. diagonal supports to the inside of secure loosely. the floor bar and support poles, all with the same bolt.

13 21

8 05 21 43 52 43 52 8 STEP STEP STEP 1 4 5 22 6

Slide an extra bolt into the groove On the inside of each corner bracket, Lastly, use the extra bolt in the of the support pole. Then bolt the attach the diagonal supports to the grooves of the support poles to top of the support poles to the lowest bolt and the horizontal secure the horizontal support outside of the roof beams using support to the second-to-lowest bolt. across the two support poles. another bolt. Open the bolts, position the supports, and refasten the bolts.

PAGE 11 ASSEMBLING THE GREENHOUSE PART 3 – FRONT WALL Lay out all the parts needed for the front wall, besides for parts 14 and 19. Follow the same layout as for the rear wall. (The image below is the outside view, so you must lay the pieces out in mirror image to start with.) Make sure that the roof beams are on the correct sides as the left and right di er; the oor bar is perpendicular to the oor, with the wider end at the top; and that the door frame parts are below the frame parts – on the outside.

Part# Part Name Part Image Qty. 1 Corner Beam 2 2 Front Right Roof Beam 1 3 Front Left Roof Beam 1 6 Right Doorway Support 1 7 Left Doorway Support 1 12 Top Doorway Beam 1 13 Corner Bracket 2 14 Door Rail 1 17 Front Floor Bar 1 19 Vertical Door Rail Support 1 23 Front Horizontal Support 2 25 Front Diagonal Support 2 38 Long Door Support Bolt 1 39 Door Frame Spacer 1 43 Bolt 22 52 Nut 23

03 12

02 STEP 14 STEP

4 19 23 7

STEP 06 25 STEP 07 01 6 01 1 & 5 25

STEP STEP 2 3 17 NOTE: PAGE 12 OUTSIDE VIEW Follow the steps below to assemble the Front Wall. NOTE:

Each step applies to both relevant corners/supports.

Note: 43 52 01

Steps 1 - 5 43 52 01 13 follow the same 17 steps used for the back wall. STEP STEP 1 2 Attach the corner brackets to the Bolt the floor bar to the inside of side and roof beams. Lay the the corner beams, securing at bracket above the two beams and each corner secure loosely.

03 07 25

17 07 43 52 03 23 07 43 52 STEP STEP STEP 1 3 4 5 25 Secure the support poles to the Slide an extra bolt into the groove On the inside of each corner bracket, outer side of the floor bar. Attach of the support pole. Then bolt the attach the diagonal supports to the the diagonal supports to the top of the support poles to the lowest bolt and the horizontal support inside of the floor bar and support outside of the top roof beams to the second-to-lowest bolt. Open the poles, all with the same bolt. using another bolt. bolts, position the supports, and refasten the bolts.

06 03

23 12

43 52 STEP STEP 07 6 7 Bolt the two short horizontal Attach the top doorway beam to the outside of the roof beams, using the supports to the insides of the top hole in the beam. Next insert a bolt from the outside into the lower support poles. hole at each end, securing loosely with a nut. PAGE 13 Follow the steps below to assemble the Door Frame.

Turn the assembled wall over so that the outside is now facing you, to make attaching the door frame easier.

02 02

14 12 12 14 06 STEP STEP 06 1 2

Slide the door rail onto the bolt heads, Insert a bolt into the hole at the end starting on the left until it reaches the of the door rail, securing with a nut. right end of the top doorway beam. This will act as a door stop. (Note: when you stand the wall up, the rail will extend on the left of the greenhouse.) When the rail is in place, tighten the two bolts.

43 52 14

03 19 19 38 39 52 STEP STEP 3 4

Attach the vertical door rail Secure the bottom of the vertical door support to the end of the door rail rail support to the outside of the roof that is jutting out of the structure. beam, using the long door support bolt. Slide the door spacer onto the bolt between the two poles, securing the joint with a nut on the inside of the roof beam.

PAGE 14 ASSEMBLING THE GREENHOUSE

PART 4 – FULL STRUCTURE AND ROOF

This section completes the greenhouse frame by joining the 4 walls and completing the roof. At this stage it is best if two people work together. Collect all the parts needed for the roof and keep on the side until necessary.

Part# Part Name Part Image Qty.

11 Roof Support Pole 2 35 Top Roof Bar 1 47 Beam End Cap 8 48 Gutter End Cap 4 43 Bolt 22 52 Nut 22

STEP 4 35 11 11 48 STEP 3 STEP 47 5

STEP 1 STEP 2

PAGE 15 Follow the steps below to assemble Full Structure and Roof.

NOTE:

Each step applies to all relevant corners/supports.

43 52 4

1 36 36 47 17 23 48 34 1

STEP 1 STEP STEP 43 52 1 2 3 25 Attach the gutter end and beam Lift the walls and bolt the side Attach the ends of the gutter bars end plastic caps to the ends of floor bars to the inside of the to the inside of the corner sections the appropriate poles, covering corner beams at each corner. on the adjoining walls. The four the exposed edges for your walls are now connected in a protection. rectangular formation.

11 43 52 35

36 43 52 2 3

STEP STEP STEP 10 4 5 6 Bolt the top roof bar to the Attach the roof support poles to the Lift the greenhouse structure onto underside of the roof beams, outside of the top roof bar and the the prepared base and secure securing with two bolts - one gutter bars. Slide an extra bolt into loosely. Check the frame is square through each of the roof beams. each pole before securing. by measuring the diagonals to be Repeat at the other end of the roof. equal. Tighten all nuts after making sure the greenhouse is sitting securely on the base.

PAGE 16 ASSEMBLING THE GREENHOUSE

PART 5 – THE DOOR

Lay out all the parts needed for constructing the door, following the layout shown. The open sides of parts 24, 26 and 27 should be facing down.

Part# Part Name Part Image Qty.

20 Left Door Support 1

24 Top Door Bar 1

26 Center Door Bar 2

27 Bottom Door Bar 1

28 Right Door Support 1

31 Door Slider (Including Rollers) 1

44 Door Screws 16

49 Rail End Cap- Right 1

50 Rail End Cap- Left 1

43 Bolt 2

52 Nut 2

24 26 26 27

PAGE 17 Follow the steps below to assemble the Door.

44 24 20 24 31 44 27 20

STEP STEP STEP 1 2 3 Screw through the door side Attach the bottom door bar as in Bolt the door slider to the outside supports into the top door bar, on step 1. Make sure that the double of the top door bar. The curved end each side. Repeat for the two edge of the bar is the lower edge. with the door rollers should stand center door bars. above the top door bar, with the rollers visible.

20 28 14 28 01 27 24 27 42 34 20 19 STEP STEP STEP 28 4 5 17 6 Make sure the door seals are in Lift the door into an upright position Slide the door slider onto the door place in the two door side support and ease the bottom bar onto the rail, sliding the rollers onto the bars, and trim any rubber that door track on the front floor bar. track. sticks out.

Right Left 49 50

14 19 06 STEP 7 Attach the plastic rail end caps on each end of the door rail. Tighten all the bolts in the door structure so that the door is held firmly and cannot wobble PAGE 18 ASSEMBLING THE GREENHOUSE

PART 6 – THE VENTS

Lay out all the parts needed for constructing the vents, following the layout shown. The greenhouse has two window vents, but instructions are for a singular vent as the procedure for installation is the same. Pay particular attention to the way that each bar should be laid, using the images for guidance.

Part# Part Name Part Image Qty.

15 Vent Support Bar 2 18 Vent Stopper 4 30 Vent Side Bar 4 32 Vent Bottom Bar 2 33 Vent Top Bar 2 A-I Vent Panels 2 45 Vent Screw 12 51 Vent Brace 2 43 Bolt 10 52 Nut 10

30 30

PAGE 19 Follow the steps below to assemble the Vents. 33 33 30 30 30 33 30 E 32 30 E

STEP STEP E STEP 30 32 1 2 30 3 Slide the vent top bar into the vent Insert bolts into the bottom of the Attach the vent bottom bar to the side bars, just over the outermost two vent side bars, securing loosely. outside of the vent side bars, using layer. The top bar should be Slide polycarbonate panel E into the bolts inserted in the previous positioned in the lower groove of the slot between the two narrow step. The top lip of the bottom bar the side bars. sheets of the bars, after removing should slide over the polycarbonate the protective film on both sides. panel, securing it in place.

33 33 30 35 18 51 30 15 32 45 03

STEP STEP STEP 45 4 5 6 Turn the vent over and attach the Check that the vent is square by Attach the two vent stoppers to the brace to the vent bottom bar, measuring that the diagonals are vent support bar, screwing into the screwing it into the pre-drilled the same, and then tighten the pre-drilled holes. Attach the stoppers holes. bolts in each corner. Slide the so that the projecting piece will stick completed vent into the top roof bar up into the space of the vent. to the space between the two roof support poles.

04 Repeat the above steps for the second 15 greenhouse vent. STEP 7 Attach the vent support bar under the vent, using the extra bolts in the roof support poles. Check that the bar is flushwith the vent before securing.

PAGE 20 ASSEMBLING THE GREENHOUSE

PART 17 – INSERTING THE PANELS

One at a time, place Remove the protective film Secure each panel with each transparent panel from each side of the panel panel clips, placing a clip in its place within the as you position it. wherever there is a marking greenhouse frame. on the diagrams below.

TO ATTACH THE PANEL CLIPS:

STEP STEP STEP 1 2 3 Using two fingers, apply Make sure the wide center Push the two ends of the pressure to the two portion of the clip remains clip into the groove in the rounded points of the clip, visibly on top of the panel. greenhouse frame. The positioning them under panel should now be the polycarbonate panel. securely in place. INSERTING THE PANELS

1) Start by inserting the roof panels, putting the panels in place on both sides of the roof before moving forward to the next row of roof panels.

36 35 32

Slide the panels into Slide the panels below Make sure the bottom of the lowest groove of the window vents into all the roof panels are the top roof bar. the groove of the vent positioned above the lip support bar. of the gutter bars.

2) Continue by inserting the side wall panels, securing each panel with clips before continuing to the next panel. Next insert the back and front panels, and lastly insert the panels of the door.

Your greenhouse is now fully secure and functional. Happy Planting!