Echlin DigitalBelden Fuel Injector Flow Bench and Ultrasonic Cleaning System
IMPORTANT - INJECTOR SERVICE INFORMATION
QUALIFY THE INJECTORS TO BE SERVICED BY PART NUMBER AND APPLICATION.
CORROSION OR RUST CONTAMINATION IN INJECTOR INLET CANNOT BE PROPERLY CLEANED. CLEANING INJECTOR WILL NOT RESOLVE PROBLEM AND INJECTORS MUST BE REPLACED.
INJECTORS WITH BROKEN OR DAMAGED PINTLE TIPS CANNOT BE REPAIRED. INJECTORS MUST BE REPLACED.
BEFORE DISASSEMBLING THE INJECTOR, MAKE SURE YOU HAVE THE NECESSARY REPAIR COMPONENTS. SOME INJECTOR COMPONENTS CANNOT BE REPLACED OR ARE NOT AVAILABLE FROM ASNU. REFER TO THE INJECTOR INDEX.
ADAPTER APPLICATIONS: WE ARE NOT ABLE TO IDENTIFY EVERY APPLICATION THIS IS
ONLY A GUIDE, PLEASE REPER TO PAGES TO THE INJECTOR INDEX.
ACCESSORY INFORMATION: REFER TO PAGES
FOR THE BEST PERFORMANCE, CLEANED INJECTORS SHOULD BE INSTALLED IN VEHICLE IMMEDIATELY AFTER SERVICING WITH ASNU.
SHELF LIFE: SERVICED INJECTORS THAT WILL NOT BE RE-INSTALLED TO A VEHICLE ENGINE MUST BE TREATED WITH AN INHIBITER AND FITTED WITH EITHER 2-15110 OR 2-15114 DUST PROTECTION CAPS. FAILURE TO FOLLOW RECOMENDATIONS COULD RESULT IN SEIZURE OF INTERNAL COMPONENTS. REFER TO ASNU OPERATION MANUAL FOR PROPER PROCEDURE.
DUST PROTECTION CAPS MUST BE INSTALLED TO PREVENT CONTAMINATION & PRE- SURVE INJECTOR SHELF LIFE. SEE INJECTOR INDEX TO SELECT PROPER PROTECTIVE CAPS. IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 222
Copyright 2009 ASNU Corporation All Rights Reserved
Machine Warranty
All repairs or replacements of machines will be handled NAPA Echlin DSM.
All questions regarding inoperative machines will be conducted through your local NAPA Echlin DSM.
If a machine breaks down and repairs cannot be determined in the field, the NAPA Echlin DSM will get authorization to ship the machine back to the factory for repairs or replacement for up to one year after purchase. The customer will be instructed where to ship the machine prepaid and then all freight charges will be re-reimbursed.
If the customer is able to determine the problem causing an inoperative machine, upon approval of the NAPA Echlin DSM, the necessary parts will be shipped on a no charge basis for up to one year after purchase. The customer will perform the replacement of these parts. No labor will be paid for customer installed components.
In instances where the machine has been damaged due to user neglect, we will ship parts for a charge, plus freight. If repairs are done at the ASNU repair center, all freight, parts and labor are the responsibility of the user.
After the 12 month warranty period, the user may continue to have the machine serviced at the ASNU Repair Center, on a labor, materials and freight cost basis.
The ASNU Repair Center will not be responsible for any damage which occurs during the shipment of a machine back to the user.
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 333
Copyright 2009 ASNU Corporation All Rights Reserved
Machine Warranty
BOSCH ROCHESTER LUCAS WEBER Various GM MULTEC DISC MPI Page Page Page Page
DENSO HONDA BOSCH DELPHI Ford/Mazda/Kia KEIHIN STYLE Various Page Page Page Page
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 1 Page 111
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
BOSCH BOSCH BOSCH BOSCH D-JET Trumpet Cap Type Ford/Mazda Page Page Page Page
BOSCH K-JET BOSCH DENSO BOSCH D-JET Various Types Toyota/Mitsubushi Chrysler/Mitsubishi Page Page Page Page
JECS BOSCH BOSCH SIEMENS GDI Nissan Chrysler Ford CFI Citroen/Peugeot Page Page Page Page
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 222
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
HITACHI GDI BOSCH GDI BOSCH GDI BOSCH Mitsubushi VW Ford Ford Page Page Page Page
WEBER SIEMENS SIEMENS BOSCH Fiat/PSA VW/Audi VW/Audi Ford Page Page Page Page
SIEMENS SAGEM AIR ASSISTED Chysler BMW/KIIA Page Page 40
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 333
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
DENSO ROCHESTER/WEBER ROCHESTER/WEBER BOSCH / HOLLY Nissan /Subaru Page Page Page Page
BOSCH BOSCH/WEBER JECS JECS Chrysler DENSO/SIEMENS Nissan/Toyota Nissan Page Page Page Page
JECS JECS DENSO DENSO Toyota Nissan Mazda Nissan Page Page Page Page
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 444
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
KEIHIN KEIHIN BOSCH BOSCH Honda Honda Ford Nissan Page Page Page Page
BOSCH DENSO GM EARLY VORTEC SYSTEMS Chrysler Susuki Page Page Page
GM LATE VORTEC SYSTEMS GM LATE VORTEC SYSTEMS Page Page
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 555
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15004 2-15114 O-RING-BROWN 2-15001 DUST CAP TOP & BOTTOM FILTER
2-15038 2-15662 PINTLE CAP 2-15012 SPACER-1mm MULTIHOLE 3mm SPACER 2mm HOLE
2-15671 2-15663 2-15035 PINTLE CAP PINTLE CAP PINTLE CAP MULTIHOLE FOR BMW 3mm HOLE OPEN ENDED 3mm HOLE GM / BMW MERCEDES (16V & 24V ENGINES) BOSCH MULTI HOLE TYPE 2-15536 with filter in.
2-15511 2-15536 2-15502 Test Adapter for Test Adapter for Universal Injector injectors with injectors with Wire Harness filter removed filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 1
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15001 2-15004 O-RING-BROWN FILTER TOP & BOTTOM
2-15114 2-15109 CAP (2 REQ) SPACER
GM ROCHESTER MULTEC Use Adapter 2-15536 with filter in.
2-15511 2-15536 2-15502 Test Adapter for Test Adapter for Universal Injector injectors with injectors with Wire Harness filter removed filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 222
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
Warning Use only ASNU 02 with these 2-15013 Injectors O-RING TOP AND BOTTOM
NA 2-15110 FILTER CAP (2 REQ)
ROVER / BMW SAAB / PSA LUCAS IDISC Use Test Adapter 2-15536 with filter in.
2-15511 2-15536 2-15502 Test Adapter for Test Adapter for Universal Injector injectors with injectors with Wire Harness filter removed filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 333
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
NA NA FILTER PINTLE CAP
2-15012 2-15004 SPACER O-RING
2-15114 CAP (2 REQ)
FORD / FIAT PSA (EUROPE)
Weber
Use Test Adapter 2-15536 with filter in. 2-15511 2-15536 Test Adapter for Test Adapter for 2-15502 injectors with injectors with Universal Injector filter removed filter installed Wire Harness
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 444
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15001 2-15019 FILTER PINTLE CAP
2-15009 2-15007 O-RING DUST SEAL
2-15114 2-15008 2-15110 DUST CAP HEAD SEAL DUST CAP
FORD / FIAT PSA (EUROPE) Weber Use Test Adapter 2-15536 with filter in.
2-15511 Test Adapter 2-15538 2-15502 Test Adapter for test injectors with Universal Injector injectors with filter installed Wire Harness filter removed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 555
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15014 2-15015 2-15041 GREEN SEAL O-RING HEAD SEAL
PINTLE CAP CANNOT BE REPLACED. DO NOT REMOVE FOR INJECTOR CLEANING OR TESTING 2-15016 GROMMET
2-15064 2-15114 2-15110 FILTER CAP CAP
HONDA KEIHIN STYLE Use Test Adapter 2-15538 with filter in.
2-15511 2-15538 2-15502 Test Adapter for Test Adapter for Universal Injector injectors with injectors with Wire Harness filter removed filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 666
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15013 2-15001 O-RING FILTER (TOP & BOTTOM)
USE 2-15640 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS
PLASTIC O'RING RETAINING WASHER NOT YET AVAILABLE, REMOVE CAREFULLY AND RE-USE OLD WASHER
VARIOUS VEHICLES BOSCH EV6 MULTIPOINT
Use Test Adapter 2-15538 use Adapter 2-15640 plate in fuel rail for testing 2-15511 2-15536 2-15502 Test Adapter for Test Adapter for Universal Injector injectors with injectors with Wire Harness filter removed filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 777
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2- 2- 2-15001 O-RING O-RING FILTER (LOWER) (UPPER)
USE ASNU 89 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS
PINTLE CAP NOT YET AVAILABLE DO NOT REMOVE
BUICK Delphi production Use Injector Adapter 2-15536 Use custom harness 2-15637
INJECTOR ADAPTER 2-15536 DELPHI WIRING HARNESS 2-15637 (Tests Injectors with filter installed)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 888
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15020 2-15019 2-15006 PINTLE CAP PINTLE CAP O-RING
2-15001 2-15110 2-15114 FILTER CAP CAP
2-15010 2-15024 2-15011 O-RING FERRULE SEAL
GM / JAGUAR FIAT-ALFA Use Adapter 2-15537 with hose and filter installed 2-15511 2-15537 2-15502 Test Adapter for Tests injectors with hose Universal Injector injectors with & filter installed Wire Harness filter removed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 999
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15019 2-15001 2-15006 PINTLE CAP FILTER O-RING
2-15011 2-15110 2-15114 SEAL CAP CAP
2-15006 2-15024
HEAD SEAL FERRULE
MERCEDES JAGUAR / VOLVO BOSCH D-JETRONIC Use Adapter 2-15537 with hose installed Use Adapter 2-15511 without hose and filter installed
Connect Injectors with 2-15502
Universal Harness
2-15511 2-15537 2-15502
(ASNU 51) (ASNU 58) (ASNU 70) Test Adapter for Tests injectors with hose Universal Injector injectors with & filter installed Wire Harness filter removed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 101010
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15012 ASNU 14 2-15001 WASHER O-RING (2 REQ) FILTER
2-15017 ASNU 23 PLASTIC PINTLE CAP BOTTOM O'RING RENAULT RENAULT CLIO ONLY CLIO ONLY
2-15110 2-15114
CAP CAP
GM / SAAB Chimney Style Aliminium Pintle Cap 2-15536 with filter in
Replacement cap not available, remove and replace with 2-15672
2-15511 2-15536 2-15502 Test Adapter for Tests injectors with hose & Universal Injector injectors with filter installed Wire Harness filter removed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 111111
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15096 2-15097 2-15098 2-15099 2-15067 PINTLE CAP PINTLE CAP PINTLE CAP PINTLE CAP PINTLE CAP BLACK - BLACK - BLACK - 10 DEG 18 DEG 3 DEG
2-15070 2-15001 2-15110 2-15114 2-15007 PINTLE CAP FILTER CAP CAP bushing 18 SPRAYS
2-15009 2-15102 2-15008
O'RING O'RING HEAD SEAL FORD / HYUNDAI MAZDA / PROTON Pintle type with SINGLE SPRAY exit hole. For Multi Hole Spray See page 25
Use Test Adapter 2-15538 with filter in
2-15511 2-15538 2-15502 Test Adapter for Tests injectors with filter in- Universal Injector injectors with stalled Wire Harness filter removed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 121212
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 240 2-15019 2-15001 COPPER PINTLE CAP FILTER WASHER
2-15107 2-15110 2-15006 BLEEDER CAP HEAD SEAL O-RING
CADILLAC 2-15302 Use Test Adapter 2-15511 O-RING Connect Injectors with 2-15502
Universal Harness
Test Adapter 2-15511 2015502 tests injectors with hose Universal Injector & filter removed Wire Harness
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 131313
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15109 2-15002 2-15114 0-RING O-RING CAP AUDI APPLICATIONS
2-15108 2-15101 2-15110 MOUNTING SEAL MOUNTING SEAL CAP VARIOUS BMW
K-JETRONIC BOSCH MECHANICAL FUEL INJECTOR & COLD START VALVES
Use Adapter 2-15535 or 2-15514 or 2-15515
Test Adapter Test Adapter 2-15514 Test Adapter 2-15515 2-15535 10mm Female 8mm Male 12mm Female Coupling Coupling For Male Coupling for Female K-Jet for Male K-Jet K-Jet & Cold Start & Cold Start
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 141414
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15009 2-15008 2-15106 O-RING HEAD SEAL BUSHING
2-15019 2-15001
PINTLE CAP FILTER
2-15110 2-15114
CAP CAP
MAZDA Use Test Adapter 2-15538 with filter in
Test Adapter 2-15538 tests 2-15502 Test Adapter 2-15511 test s injectors with filter Universal Injector injectors with filter removed installed Wire Harness
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 151515
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15009 2-15008 2-15007 ASNU 241 O-RING HEAD SEAL DUST SEAL O-RING
2-15055 ASNU 243 2-15062 2-15001 SEALING O-RING HOUSING SEAL HOUSING RING FILTER
2-15021 2-15019 2-15110 2-15114 PINTLE CAP PINTLE CAP DUST CAP DUST CAP
TOYOTA MAZDA Use test Adapter 2-15538 with filter in
Test Adapter 2-15511 Test Adapter 2-15538 2-15502 tests injectors with filter tests injectors with Universal Injector removed filter installed Wire Harness
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 161616
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15009 2-15033 O-RING COLLAR
2-15094 2-15110 INSULATOR SEAL DUST CAP
CHRYSLER NISSAN Use Test Adapter 2-15538 with filter in
Connect Injectors w/ 2-15502 Universal Harness 2-15114 Test Adapter 2-15511tests DUST CAP injectors with filter removed
2-15502 Test Adapter 2-15538 tests Universal Injector injectors with filter installed Wire Harness
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 171717
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15001 2-15019
FILTER PINTLE CAP
2-15006 2-15009 2-15051 O-RING O-RING BUSHING
2-15110 2-15114
NISSAN DUST CAP DUST CAP Use Test Adapter 2-15538 with filter in Connect injectors w/ 2-15502 Universal Harness
2-15511 2-15538 2-15502 Test Adapter for Test Adapter for Universal Injector injectors with injectors with Wire Harness filter removed filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 181818
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15001 2-15110 FILTER DUST CAP BOTTOM
2-15114 2-15004 DUST CAP TOP TOP O-RING
2-15011 ASNU 273 BODY CLAMPING SEAL LOWER BODY O'RING SEAL
CHRYSLER TBI SINGLE UNIT
Use Test Adapter 2-15536 with filter in
2-15536 2-15502 INJECTOR ADAPTER Universal Injector Tests injectors with filter installed Wire Harness
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 191919
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
2-15501 2-15312 2-15068 2-15069 FILTER FILTER CFI PINTLE CAP PINTLE CAP
2-15304 2-15302 2-15114 2-15110 LOWER O-RING UPPER O-RING DUST CAP TOP DUST CAP BOTTOM
FORD CFI DUAL UNIT Use Test Adapter 2-15511
2-15511 2-15502 INJECTOR ADAPTER Universal Injector Wire Harness Tests injectors with filter removed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 202020
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 262 ASNU 264 O-RING (TOP) FILTER
ASNU 263 ASNU 265 SPLIT SPACER NYLON SEALING BUSH
CITROEN PEUGEOT- GDI SIEMENS Gasoline Direct Injection Use Test Adapter ASNU 56 with filter in
INJECTOR ADAPTER WIRING HARNESS ASNU 56 2-15502 Tests injectors with Universal Injector filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 212121
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
TO TEST: REMOVE TOP O'RING & SPLIT WASHER. REPLACE WITH 2 x 2-15004 & USE 2-15536 COUPLING
ASNU 234 ASNU 20 O-RING FILTER
MITSUBUSHI HITACHI - GDI Gasoline Direct Injection Use Test Adapter 2-15536 with filter in
INJECTOR ADAPTER WIRING HARNESS 2-15536 2-15502 Test injectors with Universal Injector filter installed
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 222222
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 2-15001 O-RING (TOP) FILTER
ASNU 265 NYLON SEALING BUSH
FORD - GDI BOSCH Gasoline Direct Injection Use Test Adapter 2-15536 with filter in
WIRING HARNESS INJECTOR ADAPTER 2-15536 2-15502 (Tests injectors with filter installed) Universal Injector
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 232323
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 2-15001 0-RING (TOP & BOTTOM) FILTER
ASNU 265 NYLON SEALING BUSH
VW - GDI Bosch Gasoline Direct Injection Use Test Adapter 2-15536 with filter in
WIRING HARNESS INJECTOR ADAPTER 2-15536 2-15502 (Tests injectors with filter installed) Universal Injector
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 242424
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 2-15001 BOTTOM O-RING FILTER
USE 2-15640 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS
ASNU 239 BOTTOM 0-RING
FORD - USA BOSCH Use Test Adapter 2-15536 with filter in Use 2-15640 Adapter Plate in fuel rail for testing
INJECTOR ADAPTER 2-15536 WIRING HARNESS Test Adapter 2-15511 tests injectors (Tests injectors with 2-15502 with hose & filter removed filter installed) Universal Injector
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 252525
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 ASNU 04 O-RING (TOP & BOTTOM) FILTER
USE 2-15640 - INJECTOR MOUNTING PLATE IN FUEL RAIL TO HOLD INJECTORS
CITROEN PEUGEOT RENAULT FIAT Weber & Siemens Use Test Adapter 2-15536 with filter in Use 2-15640 Adapter Plate in fuel rail for testing
INJECTOR ADAPTER Test Adapter 2-15511 tests WIRING HARNESS 2-15536 injectors with hose & filter re- 2-15502 (Tests injectors with moved Universal Injector filter installed)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 262626
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 ASNU 03 O-RING (TOP & BOTTOM) FILTER
PINTLE CAPS ARE NOT REMOVABLE
VW / AUDI SIEMENS Use Test Adapter 2-15536 with filter in
INJECTOR ADAPTER WIRING HARNESS Test Adapter 2-15511 tests injectors 2-15536 2-15502 with hose & filter removed (Tests injectors with Universal Injector filter installed)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 272727
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 2-15001 O-RING (TOP & BOTTOM) FILTER
PINTLE CAPS ARE NOT REMOVABLE
VW / AUDI SIEMENS Use Test 2-15536 with filter in
INJECTOR ADAPTER 2-15536 WIRING HANESS 2-15502 Test Adapter 2-15511 tests injectors (Tests injectors with with hose & filter removed filter installed) Universal Injector
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 282828
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 2-15001 0-RING (TOP & BOTTOM) FILTER
PINTLE CAPS ARE NOT REMOVABLE
FORD USA SIEMENS Use Test Adapter 2-15536 with filter in
INJECTOR ADAPTER WIRING HARNESS 2-15536 2-15502 (Tests injectors with filter installed) Universal Injector
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 292929
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 2-15001 0-RING (TOP & BOTTOM) FILTER
PINTLE CAPS ARE NOT REMOVABLE
CHRYSLER USA SIEMENS Use Test Adapter 2-15536 with filter in
INJECTOR ADAPTER WIRING HARNESS 2-15536 2-15502 (Tests injectors with filter installed) Universal Injector
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 303030
Copyright 2009 ASNU Corporation All Rights Reserved
Top Feed Injectors
ASNU 14 2-15001 O-RING (TOP) FILTER
Test Adapter 2-15511 tests injectors ASNU 21 with hose & filter removed O-RING (BOTTOM)
BMW / KIA Air Assisted Sagem Use Tests Adapter 2-15536 with filter in
INJECTOR ADAPTER WIRING HARNESS 2-15536 2-15502 (Tests injectors with filter installed) Universal Injector
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 3 Page 313131
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15031 ASNU 60F 2-15110 SIDE FEED FILTER HOUSING WASHER DUST CAP
ASNU 60C 2-15301 2-15320 WEBER FILTER ROCHESTER FILTER HOUSING O-RING
WEBER / ROCHESTER LARGE MONO POINT / SINGLE POINT TBI (USA) Use Test Adapter 2-15518
(single injector block includes custom harness) ASNU 60B 2-15319 or WEBER BOTTOM O-RING ROCHESTER BOTTOM O-RING ASNU 60J Use Test Adapter 2-15598 DUST SEAL (twin injector block includes custom harness)
2-15518 2-15598
ADAPTER BLOCK ADAPTER BLOCK
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 111
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15307 2-15110 O-RING (ROCHESTER) CAP
2-15093 ASNU 64C WEBER FILTER WEBER FILTER ASNU 64F ASNU 64E ROCHESTER FLTER ROCHESTER FILTER
ASNU 64B O-RING
VARIOUS APPLICATIONS WEBER / ROCHESTER SMALL MONO POINT / SINGLE POINT TBI (USA)
Use Test Adapter 2-15519 (single injector block includes custom harness) or Use Test Adapter 2-15632 4 injector block (includes custom har- ness)
2-15632 2-15519 ADAPTER BLOCK & HARNESS ADAPTER BLOCK GM TBI MULTEC 700
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 222
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15065 2-15321
FILTER O-RING (LOWER)
2-15669
CHRYSLER CFI SINGLE UNIT BOSCH (LONG VERSION) Use Test Adapter 2-15597 (single block)
or Test Adapter 2-15528(twin block)
2-15528 2-15597
(twin block w/harness) (single block w/harness)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 333
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15048 2-15077 2-15019 SEAL FILTER PINTLE CAP (Nissan)
2-15049 2-15673 2-15635 PLASTIC WASHER O-RING CAP
2-15674
LOWER O-RING
NISSAN / SUBARU SINGLE POINT Use Test Adapter 2-15523 (single block) MULTI POINT
Use Adapter 2-15608 (6 inj. block) Connect injectors with universal harness 2-15502 2-15523 Use 2-15608 2-15608 SINGLE BLOCK 4 INJ. BLOCK 6 INJ. BLOCK
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 444
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15032 2-15043 2-15066 O-RING (UPPER) O-RING (LOWER) CLIP (UPPER)
2-15672 2-15065 2-15093 FILTER (NEW TYPE) (UPPER) FILTER (UPPER) FILTER (LOWER)
VARIOUS APPLICATIONS BOSCH MONOPOINT / SINGLE POINT TBI (USA)
Use Test Adapter 2-15524 (single block includes custom harness)
2-15524 2-15110 2-15671 ADAPTER BLOCK WITH CUSTOM DUST CAP PINTLE CAP HARNESS
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 555
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15032 2-15679 2-15065 O-RING TOP O-RING BOTTOM FILTER
WEBER & SIEMENS INJECTORS HAVE NO REMOVABLE PINTLE CAPS
2-15070 2-15659 TWIN SPRAY SINGLE SPRAY PINTLE CAP PINTLE CAP BOSCH DENSO VARIOUS APPLICATIONS BOSCH, WEBER, DENSO, SIEMENS Use Test Adapter 2-15530 (block holds 4 injectors) or Test Adapter 2-15635 (block holds 6 injectors for Chrysler 3.5L)
Connect injectors with universal harness 2-15502
2-15635 2-15530 ADAPTER BLOCK ADAPTER BLOCK (Holds 6 injectors - Jaguar & (Holds 4 injectors - Ford Zeta Chrysler 3.5L)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 666
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15682 2-15114 O-RING (UPPER) CAP
2-15612 ASNU 102C O-RING (LOWER) FILTER
NISSAN & TOYOTA Use Test Adapter 2-15598 (block holds 2 injectors, includes custom harness)
2-15607 ADAPTER BLOCK
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 777
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15039 2-15613 2-15685 TOP O-RING BOTTOM O-RING NISSAN BOTTOM O-RING TOYOTA
2-15053 2-15050 2-15052 TOP O-RING Nissan / Toyota Housing TOP O-RING Nissan / TOP O-RING Nissan / Toyota seal (large) Toyota Housing seal (small) Housing seal (medium)
NISSAN JECS Use Test Adapter 2-15609 ASNU 103C ASNU 103E 2-15685 (block holds 6 injectors) FILTER PINTLE CAP FILTER / SPACER Connect injectors with universal harness 2-15502
2-15609 2-15613 2-15110 ADAPTER BLOCK BLANKING OFF PLUG DUST CAP
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 888
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2- 15060 2-15058 2-15687 O-RING O-RING O-RING
REPLACEMENT FILTER CURRENTLY NOT AVAILABLE DO NOT REMOVE FILTER
2-15059 2-15110 INSULATOR CAP
TOYOTA JECS Use Test Adapter 2-15606 (block holds 4 injectors) Connect injectors with universal harness 2-15502
2-15606 2-15502 TWIN ADAPTER BLOCK UNIVERSAL INJECTOR WIRE HARNESS
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 999
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15029 2-15689 O-RING (UPPER) O-RING (LOWER)
REPLACEMENT FILTER NOT CURRENTLY AVAILABLE DO NOT REMOVE FILTER
2-15114 CAP NISSAN JECS Use Test Adapter 2-15529 (block holds 4 injectors) Connect injectors with universal harness 2-15502
2-15529 ADAPTER BLOCK 2-15502 UNIVERSAL INJECTOR WITH HARNESS
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 101010
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15690 2-15004 TOP O-RING BOTTOM O-RING
REPLACEMENT FILTER CURRENTLY NOT AVAILABLE DO NOT REMOVE
FILTER 2-15659 SINGLE SPRAY PINTLE 2-15070 CAP BOSCH TWIN SPRAY PINTLE CAP DENSO
MAZDA NIPPON DENSO Use Test Adapter 2-15634 (Injector block) Connect injectors with universal harness 2-15502
2-15634 6 INJ. BLOCK 2-15613 BLANKING OFF PLUG
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 111111
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15692 2-15693 TOP O-RING BOTTOM O-RING
REPLACEMENT FILTER CURRENTLY NOT AVAILABLE DO NOT REMOVE FILTER
NISSAN JECS Use Test Adapter 2-15661 (4 Injector block) Connect injectors with universal harness 2-15502
2-15661 4 INJ. BLOCK 2-15502 UNIVERSAL INJECTOR WIRE HARNESS
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 121212
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15029 2-15030 TOP O-RING MIDDLE O-RING
2-15040 2-15110 UPPER SEAL CAP
HONDA CIVIC KEIHIN Use Test Adapter 2-15636 (double block) Connect injectors with universal harness
2-15502
2-15636 2-15502 TWIN ADAPTER BLOCK UNIVERSAL INJECTOR WIRE HARNESS
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 131313
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15029 2-15030 TOP O-RING MIDDLE O-RING
2-15036 2-15040 2-15110 BOTTOM O-RING UPPER SEAL CAP
HONDA CIVIC KEIHIN Use Test Adapter 2-15636 (double block) Connect injectors with universal harness 2-15502
2-15502 2-15636 UNIVERSAL INJECTOR WIRE TWIN ADAPTER BLOCK HARNESS
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 141414
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15309 2-15314 O-RING (LOWER) O-RING (UPPER)
ASNU 61C FILTER
FORD CFI SINGLE UNIT BOSCH Use Test Adapter 2-15597 (single block) or Test Adapter 2-15528 (block)
2-15597 2-15528 ADAPTER BLOCK ADAPTER BLOCK (Includes Custom Harness) (Includes Custom Harness)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 151515
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15322 2-15306 2-15321 O-RING (UPPER) FILTER O-RING (LOWER)
222-2---1566915669 CUP (Bosch Style Only)
NISSAN CFI SINGLE UNIT BOSCH Use Test Adapter 2 2-15597 (single block) or Test Adapter 2-15528 (twin block)
2-15597 2-15528 (single block w/harness) (twin block w/harness)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 161616
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15065 2-15322 2-15321 FILTER O-RING (UPPER) O-RING (LOWER)
222-2---1566915669 CUP (Bosch Style Only)
2-15669
CHRYSLER CFI SINGLE UNIT BOSCH (LONG VERSION) 2-15597 (single block) or Test Adapter 2-15528 (twin block)
2-15597 2-15528 (single block w/harness) (twin block w/harness)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 171717
Copyright 2009 ASNU Corporation All Rights Reserved
Side Feed Injectors
2-15027 2-15026 O-RING O-RING
REPLACEMENT FILTER CURRENTLY
NOT AVAILABLE DO NOT REMOVE FILTER
2-15114 DUST CAP
SUZUKI MONOPOINT DENSO Use Test Adapter 2-15525 (single block)
2-15525 ADAPTER BLOCK WITH CUSTOM HARNESS
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 4 Page 181818
Copyright 2009 ASNU Corporation All Rights Reserved
Vortec Injectors
SPRAYING SECURING FLOWING
2-15631 Test Adapter Kit Includes plastic cleaning tray (see below) for ultrasonic cleaning of individual injector coils & frame mount shown below. Injector components not available at this time
Use Test Adapter 2-15631 (tests & cleans complete assembly ) Connect injectors with 2-15629 Universal Harness GM VORTEC 4.3L V-6 & 5.7L CPI
2-15631 2-15660 2-15629 Test Adapter Stainless Steel Frame in Anodized Aluminum Cleaning Tray Vortec Harness Rail Complete with cleaning tray
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 5 Page 111
Copyright 2009 ASNU Corporation All Rights Reserved
Vortec Injectors
ASNU 108A ASNU 108B ASNU 108C O-RING Early style GM Vor- O-RING Early style GM Vor- O-RING Early style GM tex 4.3L tex 4.3L Vortex 4.3L
ASNU 108D ASNU 108E O-RING Early style GM Vor- O-RING Early style GM tex 4.3L Vortex 4.3L
GM VORTEC 4.3L V-6 CPI MODELS 92-95
Use Test Adapter 2-15630 (tests complete assembly)
2-15630 ASNU 108T Test Adapter Kit Cleaning Tray (optional)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 5 Page 222
Copyright 2009 ASNU Corporation All Rights Reserved
Accessories, Components and Adaptors
2-15593 2-15627 ASNU 46 FLOW-RITE BIO-CLEAN ULTRASONIC CLEANING FLUID ADAPTER COUPLING HITACHI INJECTORS CALIBRATION FLUID 5 LITER BOTTLE USED ON AUDI QUATTRO 5 LITER BOTTLE
2-15533 2-15532 2-15534 10MM MALE ADAPTER COUPLING 8MM FEMALE ADAPTER COUPLING FOR ADAPTER COUPLING COLD START FOR 10MM FEMALE COLD START 8MM MALE COLD START INJECTOR INJECTOR HOSE TYPE (12-13MM) INJECTOR
2-15535 2-15511 2-15512 10MM FEMALE ADAPTER COUPLING ADAPTER COUPLING TOP FEED MULTI- FOR 10MM MALE COLD START PORT INJECTORS WITH FILTER INJECTOR BASKET REMOVED SMALL O-RING FOR 2-15511 COUPLING
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 111
Copyright 2009 ASNU Corporation All Rights Reserved
Accessories, Components and Adaptors
2-15513 2-15514 2-15515 LARGE (TOP) O-RING FOR ASNU ADAPTER 8MM MALE ADAPTER COUPLING FOR 10MM 12MM FEMALE ADAPTER COUPLING COUPLING FEMALE CIS (K-JET) FOR 12MM MALE CIS (K-JET)
NOT AVAILABLE
2-15536 ASNU 56 2-15537 ADAPTER COUPLING BOSCH, LUCAS, ADAPTER COUPLING FOR SLIM TOP ADAPTER COUPLING TESTS WEBER, MARELLI, SIEMENS TESTS SIEMENS GDI INJECTORS TESTS INJEC- MULTIPORT INJECTORS WITH FUEL INJECTORS WITHOUT REMOVING INLET TORS WITHOUT REMOVING INLET FILTER HOSE INSTALLED FILTER
2-15538 2-15502 2-15610 ADAPTER COUPLING SLIM TYPE DENSO UNIVERSAL INJECTOR HARNESS REPAIR KIT FOR MAIN ASNU TESTS INJECTORS WITHOUT REMOVING CONNECTS MOST MULTIPORT INJECTORS INJECTOR HARNESS INLET FILTER
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 222
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
2-15526 2-15518 2-15519 ADAPTER BLOCK ADAPTER BLOCK ADAPTER BLOCK FORD CFI - HOLLEY SPI CHRYSLER & GM TBI MAXI WITH CUSTOM HARNESS GM TBI MULTEC WITH CUSTOM HARNESS BOSCH WITH CUSTOM HARNESS (single block - use 2-15598 for double (single block - use 2-15632 for Quad (single block - use 2-15528 for double block) Block) block)
2-15522 2-15529 2-15524 ADAPTER KIT ADAPTER BLOCK ADAPTER BLOCK MITSUBISHI MPI WITH CUSTOM HAR- NISSAN / SUBARU SPI BOSCH SPI NESS (Tests 4 injectors) (Tests 1 injector) (Tests 2 injectors)
2-15530 2-15525 ADAPTER BLOCK ADAPTER BLOCK ADAPTER BLOCK FORD ZETA MPI / SPI SUZUKI SPI NISSAN / SUBARU SPI (BOSCH / WEBER / SIEMENS / DENSO) (Tests 1 injector) (Tests 1 injector) (Tests 4 injectors)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 333
Copyright 2009 ASNU Corporation All Rights Reserved
Accessories, Components and Adaptors
DISCONTINUED DISCONTINUED
2-15638 NLA FILTER BASKET CUSTOM NYLON COVER "FOAMEX" REMOVAL TOOL FOR ASNU MACHINE WEATHERPROOF SIGN T-HANDLE TYPE
COMPONENT ASSTS 2-15594 2-15100 / FILTERS & CAPS 2-15639 PINTLE CAP 2-15200 /O'RINGS-SEALS PINTLEPINTLE CAP CAP & & FILTER FILTER BASKET BASKET REMOVAL TOOL 2-15300 /MONOPOINT KIT ASSEMBLY TOOL GUN TYPE
2-15595 2-15521 2-15510 FILTER REMOVAL TOOL PLASTIC RUBBER BENCH MAT GUN TYPE RAIL HOLDER
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 444
Copyright 2009 ASNU Corporation All Rights Reserved
Accessories, Components and Adaptors
2-15640 2-15605 2-15531 WEBER / SIEMENS INJECTOR SERVICE TBI ADAPTER RING TOP FEED MULTIPOINT REPORT PAD USE W/ 2-15507 CRADLE "MINI PECO INJECTOR" 50 SELF CARBON LARGE TBI INJECTORS ADAPTER PLATE (ENGLISH ONLY) (GM MAXI)
2-15641 2-15601 SIDE FEED INJECTOR CLEANING TBI ADAPTER RING 2-15520 TRAY USE W/ 2-15507 CRADLE SMALL TBI IN- CIS (K-JET) INJECTOR (SHALLOW) JECTORS CLEANING TRAY ASNU 1992 onward GM MULTEC / DAEWOO 2-15600 ASNU UPTO 1992 (DEEP)
2-15607 2-15598 2-15642 ADAPTER BLOCK ADAPTER BLOCK CLEANING TRAY NISSAN / TOYOTA 2 WIRE GM TBI MAXI PECO INJECTOR (Tests 2 injectors, includes blanking off (Tests 2 injectors, includes custom harness) plug & custom harness
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 555
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
2-15606 2-15609 ASNU 105 ADAPTER BLOCK ADAPTER BLOCK ADAPTER BLOCK TOYOTA JECS MPI NISSAN JECS NISSAN PATHFINDER / NAVARA PREVIA / TARAGO (Tests 6 injectors) (Tests 4 injectors) (Tests 6 injectors)
2-15608 2-15634 2-15630 ADAPTER BLOCK ADAPTER BLOCK ADAPTER GM VORTEC 4.3 EARLY VERSION NISSAN / SUBARU SPI MAZDA / DENSO (Tests complete assembly) (Tests 6 injectors) (Tests 6 injectors)
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 666
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
2-15631 ADAPTER KIT GM VORTEC 4.3L & 5.7L LATE VERSION (Tests complete assembly includes cleaning tray)
SPRAYING SECURING FLOWING
Echlin Part Numbers 2-15630 and 2-15631 Adapters comes complete with 2-15629 harness and plastic cleaning tray for ultrasonic cleaning of individual injector coils. 2-15629 Harness assembly is a available separately.
The later GM Vortec (late) system is a Multi Point operation with 6 or 8 individual injectors mounted in the housing, allowing either a simultaneous or sequential injection delivery. The fuel is pressurized into the injector housing and as the injector is electronically opened, the fuel is pressure fed into a nylon delivery tube. At the end of the tube is a pressure poppet valve. The poppet valve sits in the inlet manifold and can be subject to extremely harsh conditions that may affect the per- formance of the valve. The opening and closing of the poppet valve is controlled by pressure and deter- mines the fuel distribution, fuel atomization and the fuel delivery to each cylinder. The is therefore very important to examine the performance of this system, both before servicing (to un- derstand the cause of the engine problem) and after, to ensure the cause of the problem had been elimi- nated and that the system is working properly.
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 777
Copyright 2009 ASNU Corporation All Rights Reserved
Injector Index
2-15631 ADAPTER KIT GM VORTEC 4.3L & 5.7L LATE VERSION (Tests complete assembly includes cleaning tray)
2-15635 ADAPTER BLOCK FORD ZETA / SIEMENS CHRYSLER 3.5L (Tests 6 injectors)
2-15636 ADAPTER BLOCK HONDA CIVIC NIKI KEIHIN (Tests 2 injectors
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 888
Copyright 2009 ASNU Corporation All Rights Reserved
Accessories, Components and Adaptors
2-15637
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 999
Copyright 2009 ASNU Corporation All Rights Reserved
Accessories, Components and Adaptors
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 6 Page 101010
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing Echlin # DESCRIPTION 2-15001 Standard Injector Filter Basket with Brass Collar 2-15002 K-Jetronic (CIS) Injector O'Ring 2-15003 BMW Finned Pintle Insulator Cap - Yellow 2-15004 Standard L-Jetronic O'Ring - 15mm - Black 2-15006 L-Jetronic / Nissan / GM Injector Head Seal - Medium 2-15007 Nippon Denso Injector Rail Dust Seal (50) 2-15008 O'Ring Toyota Bottom Small Flat 2-15009 Toyota / Mazda / Nippon Denso Top O'Ring Seal 2-15010 D-Jetronic Injector O'Ring Head Seal - Small 2-15011 DUST SEAL OD 27MM ID22MM WIDTH 8MM 2-15012 Bosch L-Jetronic Injector Spacer - 2mm 2-15014 Nikki Injector Head Seal 2-15015 Nikki Injector Top O'Ring 2-15016 Honda Injector Grommet 2-15017 Bosch Trumpet End Pintle Cap 2-15018 Bosch/Nippon Denso Standard Pintle Insulator Cap 2-15019 L-Jetronic Standard Pintle Insulator Cap-Black 2-15020 D-Jetronic Pintle Insulator Cap-Black 18mm 2-15021 CAP, PKG TOYOTA PINTLE 2-15022 24 Compartment tray 2-15024 FERRULE, PKG 2-15026 O-RING, PKG INJECT LOW 2-15027 O-RING, PKG INJECT UPP 2-15029 NA FROM ACE 2-15029 O-RING, PKG INJECT UPP 2-15030 O-RING, PKG INJECT LOW 2-15031 SIDE FEED FILTER, PMAXI TBI INJ 2-15032 2-15032 O-RING, PKG INJECT UPP IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Section 7 Page 111
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing 2-15033 COLLAR, PKG INJECTOR 2-15035 Pintle Cap 2-15036 O-RING, PKG AUX INJECT 2-15039 Nissan/Toyota Side Feed Injector - Top- O-Ring 2-15040 SEAL, PKG INJECT UPPER 2-15041 SEAL, PKG INJECTOR 2-15042 CLIP, PKG INJECTOR 2-15043 O-RING, PKG INJECT LOW 2-15048 SEAL, PKG INJECTOR 2-15049 SEAL, PKG INJECTOR 2-15050 SEAL, PKG INJECTOR 2-15051 SEAL, PKG INJECTOR 2-15052 SEAL, PKG INJECTOR 2-15053 SEAL, PKG INJECTOR 2-15055 INSULATOR, PKG TOYOTA 2-15056 INSULATOR, PKG TOYOTA 2-15058 INSULATOR, PKG TOYOTA 2-15059 INSULATOR, PKG TOYOTA 2-15060 O-RING, PKG INJECTOR 2-15061 O-RING, PKG INJECTOR 2-15062 O-RING, PKG INJECTOR 2-15064 FILTER, HONDA INJECTOR 2-15065 2-15065 Screen Filter 25pk 2-15066 CLIP, SPI BOSCH 2-15067 CAP, MAZDA PINTLE 2-15068 CAP, FORD LRG PINTLE 2-15069 CAP, FORD SMALL PINTLE 2-15070 CAP, FORD 2HOLE PINTLE
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 222
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing 2-15071 O-RING, TOYOTA 2-15072 CAP, WEBER PINTLE 2-15074 Fuel Injector Pintle Cap 2-15075 SPACER, NISSAN INJECTOR 2-15076 2-15076 Fuel Injector Filter Screen 2-15077 Fuel Injector Filter Screen 2-15091 FUEL INJECTOR HOSE 2-15092 SPACER, ROCH INJECTOR 2-15093 FILTER, TBI INJECT LOW 2-15094 Inj. O-Ring 25pk 2-15095 CAP, PINTLE L-JET 2-15096 VAPOR CAP 2-HOLE 2-15097 CAP, DENSO 2HOLE VAPOR 2-15098 CAP, 2HOLE INSULATOR 2-15099 CAP, FORD INSULATOR
2-15100 Multipoint Fuel Injection Kit 2 - O'Rings, Rubber Seals & Dust Caps. 2-15101 BMW CIS (K-Jetronic) Injector O'Ring 2-15102 Mazda Injector O'Ring - Lower Mazda Injector Head Seal 2-15103 Rail Washer 100pk 2-15104 Mazda Injector O'Ring - Lower Mazda Injector Head Seal 2-15106 Mazda Grommet 2-15107 Mazda Air Bleed Socket O'Ring 2-15108 Cadillac Fuel Rail Grommet 2-15109 Audi CIS (K-Jetronic) Injector Seal 2-15110 Injector Protective Cap - Small
2-15111 Injector Protective Cap Rail Fitted Injector Protective Dust Cap 2-15112 Injector Protective Cap
2-15113 Injector Protective Cap Hose Fitted Injector Protective Dust Cap 2-15114 Injector Protective Cap - Large IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 333
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing
2-15300 Singlepoint/Monopoint Fuel Injection Kit 3 - Fiter Baskets, O'Rings & Seals. 2-15301 Rochester bottom filter basket 2-15302 Ford Injector O'Ring - Upper 2-15304 Ford Injector Mounting - Lower O'Ring 2-15305 Hitachi InjectorO'Ring - Small 2-15306 Hitachi Injector Filter Screen 2-15306 Bosch/Chrysler / Hitachi Tbi Filter Screen 2-15307 Rochester TBI Model 700 Injector O'Ring - Upper 2-15308 Inj. Washer 25pk 2-15309 Holley Tbi Injector O'ring - Lower 2-15310 Nissan Injector O'Ring 2-15311 Rochester TBI Larger Filter Screen (50) 2-15312 Ford Injector Filter Screen 2-15313 Bosch Injector O'Ring BLACK (50) 2-15314 Holley Tbi Upper O'ring 2-15315 Rochester Injector Housing Dust Seal 2-15316 2-15316 Niisan Single Point Injector 2-15317 Injector Body Support Rubber - Thick(SQUARE CORNERS) 2-15318 Bosch Injector O'Ring 2-15319 Rochester TBI Large - Lower O'Ring 2-15320 Rochester/Bendix/Weber small TBI O'Ring - Upper 2-15321 Bosch/Chrysler / Hitachi Tbi O'ring - Lower 2-15322 Bosch/Chrysler / Hitachi Tbi O'ring - Upper 2-15323 Chrysler / Hitachi Injector O'Ring 2-15500 ASNU Ultrasonic Injector Cleaner & Flow Bench 2-15502 Universal Injector Harness - Connects most multiport Injectors 2-15503 Plastic Moulded Flow Display Window 2-15504 Calibration Fluid Tank Cover 2-15506 Power Cord USA - 3metre IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 444
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing 2-15507 Ultrasonic Bath Injector Cradle 2-15508 Steel Braided Fuel Hose Complete with Quick Coupler 2-15509 Glass Measuring Cylinder - MM 2-15510 Rubber Bench Mat 2-15511 Adaptor Coupling Top Feed Multiport Injectors w/filter basker removed 2-15512 Small O-Ring for 2-15511 Coupling 2-15513 Large(TOP) O-Ring for 2-15511 Adaptor Coupling 2-15514 8mm Male Adaptor for 10MM Female CIS (K-Jet) 2-15515 12mm Female Adaptor Coupling for 12MM Male CIS (K-Jet) Adaptor Black GM TBI Maxi with Custom Harness (single block / use 2-15598 2-15518 for double block) 2-15519 GM TBI Multec w/Custom Harness (single block / use 2-15632 for Quad block) 2-15520 CIS K-Jet Cleaning Tray 2-15521 Plastic Fuel Rail Holder
2-15522 Adaptor Kit Mitsubishi MPI w/Custom Harness(Tests two injectors) ECI Two 2-15523 Adaptor Block Nissan / Subaru SPI (tests 1 injector) 2-15524 Adaptor Block Bosch SPI (tests 1 injector) 2-15525 Adaptor Block Suzuki SPI (tests 1 injector) Adaptor Block Ford CFI - Holly SPI Chrysler & Bosch w/Custom Harness 2-15526 (single block / use 2-15528 for double block) 2-15527 Adaptor Block Bosch / Holly / Nissan / Ford (tests 2 injectors) 2-15528 Adaptor Block Bosch / Holly / Nissan / Ford (tests 2 injectors) 2-15529 Adaptor Block Subaru / Nissan SPI (tests 4 Injectors) adaptor Block Ford Zeta MPI /SPI (Bosch / Weber / Siemens / Denso) (tests 4 2-15530 injectors) 2-15531 TBI Adaptor Ring - use w/2-15507 Cradle large TBI Injectors (GM Maxi) 2-15532 8mm Female Adaptor For 8mm Male Cold Start Injector 2-15533 10mm Male Adaptor for 10mm Female Cold Start Injector 2-15534 Adaptor Coupling Cold Start Injector Hose Type 12-13MM 2-15535 10mm Female Adaptor Coupling for 10MM Male Cold Start Injector
2-15536 Adaptor Coupling Bosch, Lucas, Weber, Marelli, Siemens - Tests Injector w/o 2-15537 Adaptor Coupling Tests Multiport Injectors with Hose Attached 2-15538 Adzaptor Coupling Slim Tyope Denso - Tests Injectors w/o removing inlet filter IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 555
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing 2-15539 Calibration Fluid In-Line Fuel Filter 2-15540 Calibration Fluid In-Tank Pre-pump Filter 2-15562 Ultrasonic Tank Complete Assembly 2-15593 Flow Rite calibration fluid 2-15594 Pintle Cap Removal Tool - Hand Gun Type 2-15595 Filter Basket Removal Tool - Hand Gun Type Adaptor Block Ford CFI - Holly SPI Chrysler & Bosch w/Custom Harness (single 2-15597 block / use 2-15528 for double block) 2-15598 GM-TBI Large (TBI) Dual Injector Manifold and Harness Kit 2-15599 ASNU Main Board-Service Exchange ($750 Core) 2-15600 Side Feed Injector Cleaning Tray (Deep) TBI Adaptor Ring - use w/2-15507 Cradle Small TBI Injectors (GM Multec / Dae- 2-15601 woo) 2-15602 2-15603 Quick Reference Wall Chart - English 2-15604 Instruction Manual 2-15605 Injector Service Report Pad (50 Pages per Pad) 2-15606 Toyota Tarago/Previa Quad Injector Manifold Kit 2-15607 Nissan / Toyota 2 Wire Dual Injector Manifold and Harness Kit 2-15608 Subaru / Nissan Maxima 6 Injector Manifold Kit 2-15609 Nissan Navara Multipoint Six Injector Manifold Kit 2-15610 Repair Lits for Main Injector Harness 2-15612 Injector Blank - Nissan / Toyota 2 Wire 2-15613 Injector Blank - Nissan Navara Multipoint 2-15627 Bio-Clean Ultrasonic Cleaneing Fluid 2-15629 Universal Injector Harness for Vortec System 2-15629 Wiring Harness for Vortec 2-15630 Adaptor Block GM Vortec 4.3 - Early Version 2-15631 Adaptor Kit GM Vortec - 4.3 & 5.7 Later Version 2-15632 Adaptor Block GM TBI Multec 700 ( tests 4 injectors) includes harness 2-15634 Adaptor Block Mazda / Denso (tests 6 injectors) 2-15635 Adaptor Block Ford Zeta / Siemens Chrysler 3.5 (tests 6 injectors) IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 666
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing 2-15636 Adaptor Block Honda Civic / Nikki Keihen (tests 2 injectors) 2-15637 Custom Harness Delphi Pin Type Connectors (tests up to 8 injectors) 2-15638 Injector Nylon Cover for 2-15500 ASNU Machine 2-15639 Injector Filter Basket & Pintle Cap Assembly Tool 2-15640 Adaptor Plate for Weber / Siemens (Mini Peco Injector) Side Feed Injector Cleaning Tray (Shallow) 1992 onward / 2-15600 up to 2-15641 1992 (Deep) 2-15642 Perspex cleaning tray for K-jet & Weber/Sieman Mini Peco injectors 2-15643 Magnetically Couples Electric High Performance Pump High Performance Fuel Rail Top Feed Injectors (tests 8 injectors) includes 2-15644 extension bolts for long GDI injectors 2-15645 Lid for ultra-sonic tank 2-15646 GDI injector Drive box 2-15647 Mercury Optimax 2-15648 Filter removal tool replacement bit 2-15649 Late Bosch Pintle 2-15650 Late Bosch Pintle 2-15651 Late Bosch Pintle 2-15652 Late GM Pencil Pintle 2-15653 Top O-Ring Retainer 2-15654 GM Vortex 4.3L V5 CPI Filter 2-15655 Pintle Cap Holden 2-15656 Pintle Cap Ford AU 2-15660 2-15660 NA FROM ACE 2-15661 NA FROM ACE 2-15662 1MM Spacer 2-15663 Pintle Cap; Ribbed for BNW w/4MM hole for 24V engine 2-15669 SPI/TBI Plastic Clip Cover 2-15671 Pintle Cap 2-15671 Pintle Cap- Bosch Cone Type Single Point Injector 2-15672 IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 777
Copyright 2009 ASNU Corporation All Rights Reserved
Numerical Parts Listing
2-15672 NA FROM ACE 2-15673 Upper O-Ring - Nissan SPI / MPI 2-15674 O-RING, PKG INJECTOR 2-15679 14.5 MM O-RING Brown
2-15682 Hitachi InjectorO'Ring Seal - Upper Large 2-15685 O-RING, PKG INJECTOR 2-15687 NA FROM ACE 2-15689 O-RING, PKG
2-15690 Top O-Ring for Mazda Side Feed Injectors 2-15692 NA FROM ACE 2-15693 NA FROM ACE 2-15698 Pintle Cap - Large Hole Type for "V" Spray Injectors TBA Brass / Plastic Filter Basket for Lucas Injectors TBA Brass / Wire Filter Basket for Weber Injectors
IMPORTANT Many injectors look alike. The illustrations shown in this catalogue are the best possible representations & should be used only as a guide. Prior to selecting injector components & before disassembling, always inspect the injector to be serviced. Match & select the components with the injector. Ensuring they are suitable for use.
Page 888
Copyright 2009 ASNU Corporation All Rights Reserved