SATEL LITE MOTOR SM3D22 PAGE 2
nction for nction
antenna switch antenna
SM3D22 SM3D22
SATELLITE MOTOR MOTOR SATELLITE
YOUR LOCAL SUPPLIER LOCAL YOUR
INSTRUCTIONS FOR THE THE FOR INSTRUCTIONS USE AND INSTALLATION
FOR HELP WITH THE INSTALLATION, CALL CALL INSTALLATION, THE WITH HELP FOR
with a DiSEqC 1.2/2.2DiSEqC fu a and with »GoToX« the positioner
automatic motor built-in and 1.0DiSEqCrotation,a automatic
. .
nts: (shown in the figure below) figure the in (shown nts: able preparation preparation able
ing on an erected an mast: on ing
KIT KIT CONTENTS INSTALLATION AND TOOLS REQUIRED bracket Mounting FOR U-bolt THE bracket Fixing M8 Washer M8 Nut motor SM3D22 (1 pc) Washer M8x20 Bolt Manual User's (1 pc) (4 pcs) (2 pcs) (1 pc) (4 pcs) (1 (4 pc) pcs) (4 pcs) Meter mm 13 size wrench, Fork c coaxial pliers for cutting combination and Knife, tape insulating Quality set TV and kit Satellite level Spirit too are recommended, finder satellite a and Compass
1. 3. 5. 6. 8. 9. A) compone the following contains kit motor SM3D22 The 2. 4. 7. mount dish for the required are tools following The 1. 2. 3. 4. 5. 6. 7. SATEL LITE MOTOR SM3D22 PAGE 4
SATEL LITE MOTOR SM3D22 PAGE 3
Ω
°W)
limit
h around the centre-of- the around h hour)
±25% 14V) 1.02 mm R=22 Ω/km R=22 1.02 mm Ω/km R=18 1.13 mm 155 (H) mm 155
1.7°/s (V-14V) ±25% (V-14V) 1.7°/s
two buttons on the motor for easier easier for motor on the buttons two .2/2.2 and "GoToX" compatible positioner positioner compatible "GoToX" and .2/2.2
having to program it it program to having
over two different LNBs (Ku, C, H/V, R/L) R/L) H/V, C, (Ku, LNBs different two over orbit geostationary a in of satellites TV cking iameter
1.2/2.2 compatible level and the "GoToX" function "GoToX" the and level compatible 1.2/2.2
TM
is a trademark of the Eutelsat Company Company Eutelsat the of trademark a is
TM
°
DiSEqC DiSEqC
A professional new-generation motor with a DiSEqC 1 DiSEqC a with motor new-generation professional A operation automatic for without the motor setting for function "GoToX" The reception for switch DiSEqC 1.0 antenna built-in A indication communication DiSEqC cable coaxial single a via Controlled via and programming control motor manual of Option installation tra ideal the for structure "polarmount" powerful A d 1.4m in ofto up dishes all aluminum for Suitable rotation Fast operation Silent to 99 up rotation Motor climate tropical in used be Can (EU) Slovenia in Made
SM3D22SATELLITE MOTOR FEATURES specifications: Technical protocol Operating rotation Horizontal elevation) (motor Inclination diameter antenna Maximum available positions Programmable mass antenna Maximum point gravity length support Antenna DiSEqC pole diameter motor Bent (unloaded) speed Rotation 75° satellites 50 dish) 85-cm a (with speed Rotation aluminum 140 cm, cable coaxial a via Powered 95° max.) (99° typically mode stand-by in consumption Power mode operating in consumption Power dis the rotating when 12 kg, dish) 85-cm a (with (H-18V) 2.3°/s (80 ms) consumption movement Starting 40 mm 120 mm ±25% 15 mA temperature Operating (V- 2°/s (H-18V) 2.5°/s humidity Operating 350 mA Connectors VDC 18/ 14 Connection 30 to m up cable Connection 100m to up cable Connection limits EAST-WEST step tuning Fine box with Mass ±25% mA 95-150 speed wind permissible Maximum +70°C to -25°C dish 85-cm/140-cm a for rotation during ø CU torque conductor permissible inner Maximum 100% 35% to ø CU conductor inner idle on torque permissible Maximum Nm 15 buttons Control box into packed of Dimensions min. Lifetime 7 mm F type, 75 of impedance an with cable coaxial 150 Nm programmable no fixed, hardware 0.36° per (km km/h 140 km/h/80 2.7 kg (W) x 132 x 295 (L) east-store) and (west-call two 90 + (90°E 180° over cycles 50,000 , ,
Naturally, Naturally, the
Satellites circle in a
that is the closest to WEST
that that is the closest to your place
ELEVATION
ies ies to passers-by, should the dish SUREMAKE THE DISH AHAS CLEARLINE OF y y find a vertical line SIGHT TOSIGHT SATELLITEA ALSOWHEN ROTATING
ees, roof tiles, etc.). THE DISHEAST OR WEST orizontal orizontal line
ave a line of sight (clear shot) to a satellite ave to a satellite a shot) line of (clear sight SOUTH
ended that you mount it under a roof. Rain nput reduces the quality. reception and,
a precision of at least 0.5 at degree. of precision a 40 Ankara 40.5, 42, Rome Madrid 46, s 49, Ljubljana degree. one least at of precision a with rmined bit of the sun at the equinoxes (figure below). (figure at the equinoxes sun the of bit ver.
NORTH H
AZIMUT
- on a detailed map of your country, region or cit
: on a map of your country, region or city find a h EAST SELECTING THE INSTALLATION LOCATIONINSTALLATION SELECTING THE
transfer via a coaxial cable to the satellite recei the satellite to cable coaxial a via transfer Longitude with determined be to has latitude The place. your Latitude 48, Pari Munich 52.5, 51.5, Berlin 60, (Oslo London dete be to has longitude The 30). 37, Cairo Algiers E) to has h dish -of parabolic Thethe surface entire (the path must be clear of obstructions, such or the below slightly is which orbit, as geostationary tr Make sure to prevent down. fall accidentally a possibility of causing injur The motor is watertight; nevertheless, it is recomm snow moreover, on the dish surface and at the LNB i satellite. the of sight the obstruct not roof must SATEL LITE MOTOR SM3D22 PAGE 6
t t d d h SATEL LITE MOTOR SM3D22 PAGE 5
lly sh . tter rom from from do it do he he
!
ic ic dish; it has to be located
otation otation axis is parallel to the
r r is not mounted
fall from the mast, n location as not to ays ays call an authorized
ort ort bracket get loose or dish might slide off the
In addition to secure bolt to secure bolt In addition int.
, , make sure that it is not too heavy, that its horizon. horizon. s tilted relative to the geostationary orbit at
y y (offset) dish of up to 85 cm in diameter. If the er LNB on the same dish for the reception of thin thin 95° minimum hat you call For a qualified buttechnician; if you rea the precise alignment d d for rotating a dish; satellite the motor has a fu all as possible, or else the dish will be too far f oX" commands of the satellite receiver. receiver. satellite the of commands oX" advantages s several ” alignment, which allows full tracking of all TV the la In bracket. wall a on or aerials, TV assical or by using different polarization. You can also will be too big. For a 99-degree rotation, the mas le, and that the dish rotates around the center-of- tly and so does the reception quality. Do not
a a maximum rotation angle; you can also follow them osed to hurricane winds or heavy snow, a bigger dis or operation will be error-free with an aluminum di onverts received signals received a into onverts suitable form for t where precision requirements are even less exacting less even are requirements precision where are a can you with skills, person basic mechanical way are you provided with fast access to a picture
g of all TV satellites, except for inclined ones. ones. inclined for except satellites, TV all g of
est. est.
W
ast andast
E
– a device receiving signals collected by a parabol
the the mounting mode of a rotating dish, whereby the r
– – old satellites circle in an inclined orbit that i mounting. dish for used shaft rotating – bent a
the above satellite of the altitude angular – the – an angle to the east and west of the southern po southern the and of west east the to –angle an - abbreviations for for abbreviations - DESCRIPTION PRECAUTIONS SAFETY GLOSSARY
Do Do not open and "repair" the motor on your own; alw service center. An unskillfully dish. the with together assembled motor can Be very careful when securely or the mounting mounting structure is too the weak, the dish. might be out. pulled wall theor anchors pole motor If the moto tightening, make sure to endanger passers-by choose or objects should the dish supp such an installatio out. pulled be anchors wall the B) You a bought have small, but powerful motor designe "GoT and DiSEqC 1.2/2.2 the using control automatic ha motor the SM3D22 design, innovative its to Owing - Precise installation guarantees ideal satellites “polarmount within the over (positioning) such a motor wide range we recommend t rotation angle, and carefully, if you instructions and these follow i.e. wi yourself. These instructions apply to the positioning within angle, rotation smaller a within alignment the for cl for mast on an existing mounted be can motor The case, the motor should be mounted as close to the w the wall, and the force exerted on the wall anchors (±0.5°) plumb vertically be to has Under normal circumstances, the motor works with an dish is not too heavy (up to 12 kg), and is not exp can be mounted as well. When mounting a bigger parabolic surface dish is as close to the mast as possib gravity point. If these conditions are met, the mot diameter. in cm 140 as much as - A built-in antenna switch allows additional you channels to broadcast use in anoth a different an antenna fixed additional connect to it. In this range, wait. to having without satellites two C) D) Polarmount trackin ideal virtually a provides It axis. earth's Elevation Azimuth Inclination certain angle; thus, their elevation satellites. to such dish your varies position constan W E in pole Motor LNB (Low Noise Block) in the focusprecisely of point the dish. The LNB c
Motor pole pole Motor dish with holes fixing
figure below. First assemble all the components components the all assemble First below. figure ly onto the motor. the motor. onto ly
MOTOR ASSEMBLY MOTOR
G) the in shown the steps following motor the Assemble assemb the put then and bracket, motor the to fixed this: like looks motor the assembled, When SATEL LITE MOTOR SM3D22 PAGE 8
t t SATEL LITE MOTOR SM3D22 PAGE 7
must
=
S J
LATITUDE OF YOUR LOCATION YOUR OF LATITUDE down) it (put MAP - A FROM READ IT PARALLELS SEE THE
ding, ding, while too big may get loose. Prepare the nsulating nsulating tape. In the beginning, the tape should nterconnect nterconnect the LNBs, the motor and the satellite CONENCTORASSSEMBLY he cables (F connectors) to the receiver, the motor t slightly, or else the tape will unwind or will no ch the F connectors to them. to F connectors the ch Make sure that the F connectors match the cable - motor, the motor, second one the LNB2 and the motor, and F
. . All connectors that might be exposed to moisture V
fix fix them by hand
you can only LONGITUDE OF YOUR YOUR OF LONGITUDE = LOCATION down) it (put MAP - A FROM READ IT MERIDIANS SEE THE
CONNECTING CABLE ASSEMBLY CONNECTINGCABLEASSEMBLY Z
F) You need three cables fitted with F connectors to The cable first connects receiver. the LNB1 i and the the third one the motor and the satellite receiver. diameter. Too small connectors may damage the shiel atta then and below, diagram the in shown as cables No tools whatsoever should be used for connecting t or the LNB: be protected. We recommend that you use a quality i be tightened firmly; at the end you should loosen protection. watertight provide i
Align the dish with with dish the Align bolt right-hand the line edge
Motor and dish dish and Motor assembly
SATEL LITE MOTOR SM3D22 PAGE 10
e e SATEL LITE MOTOR SM3D22 PAGE 9 of
h h
ite on
Standard metal metal Standard with bolts, metal standard inside nuts
CENTERLINE THE DISH
rresponds rresponds to your latitude. The latitude given in
set a dish adapted for the motor. motor. the for adapted dish a set
motor motor clamp (X°). Example: for Paris at a latitude de de of 46° the angle will be 46°. You can tighten th motor. the de ix it with the U-bolt (enclosed to the dish) throug
nding (please nding see the the satell Installing section
from from the
:
SETTING THE SCALE ON THE MOTOR YOURSCALETHE CLAMP TO ON THE SETTING LATITUDE ON DISHMOTOR THE THE POLE MOUNTING
ON THE MOTOR MOTOR THE ON THE SET CLAMP READ OUT LATITUDE to has edge Clamp the latitude to point value H) You have to set the motor clamp at an angle that degrees directly corresponds co to the setting on the 49° the angle will be 49°, for Slovenia at a latitu insi nuts metal standard are there as screws firmly I) dish Ordinary pole as the dish Mount the motor clamp onto shown in the figure below. The label and the point marked on the motor pole adjustment make of the dish easier. the The middle of the clamp has to be lined up precisely with the centerline on the label. clamp. dish the on dish the Finally, mount Fix the dish clamp at least bottom in 1 cm order to reduce the force exerted on the motor. Make sure the dish does not it. Secure pole. the off slide The setting of the dish elevation depends on the type instructions attached of to the dish. Most easily dish will angle be the elevation set later, at fi signal – please signal). satellite the for searching and mast, a follow the dishes: adapted Specially If you have a dish specially adapted for a motor, f pole. motor the on holes the and assemble how show to figures two following The
st
or ses ses ing
iSEqC iSEqC angle hich is hich is
as long as the button is as long as the button is
(E) (W) LED indicator of of indicator LED receipt communication 1 LNB of view Detailed F-connectors attachment 2 LNB
long or short (_------)= movement LNB input is in use in is input LNB
nd
commands receiver the Normally, ceiver.
the E/W buttons on the motor motor the on buttons E/W the ill ill be executed immediately. The result is the the fitting. All the satellites that you wish to W switch, or DiSEqC 1.0 positions 1 and 2. The
tor has not recognized it, and has not executed andexecuted not it. has it, recognized not tor has ver (switch, LNB, etc.). When the LED indicator and recognized been has Command executed and recognized, been not has Command executed been not has 2 – the Glows r), and it also provides power for the LNB. The rotating W rotating eceiver eceiver commands. A green LED denotes that the common output can electrically connect to the 1
→ a command, or the command has been intended for t; also a you to have provide for fitting the mount LNB-B. others the and LNB-A, e.g., eceiver , , etc.). To enable this, the rotation by a default dicator dicator (see the table above). The active input pas th th two LNBs different (e.g., a Ku and a C band LNB, t t an internal setting. A red LED indicates that a D w for a angle, will rotate the motor default -over,
LNB input is in use. in is input LNB ← nd
button pressed rotates the motor west button pressed rotates the motor east E E rotating W use in
Does not glow – the 1st LNB input is is input 1st LNB – glow the not Does command DiSEqC a sent has Receiver command DiSEqC a sent has Receiver
E
LNB input, depending on a command sent from the re the from sent on command a depending input, LNB
nd
THE MEANING OF OF MEANING THEFUNCTIONS THE MOTOR red MOTORIN SWITCH ANTENNATHE INTERNAL
green the buttons of view Detiled rotation motor manual for (W) west (E) and east RECEIVER SATELLITE orange at a switch-over (typically 6 at (typically a degrees) switch-over has to be se of two LNBs on a rotating dish. Mount r the at marked be should LNB first the via receive both LNBs on
K) using by motor the to control how of explanation An W-West) (E-East, E=(_------) Keeping the pressed. E=(_------) Keeping the pressed. or short (_------)= movement long indicator: LED a of meaning The The LED on the motor indicates the receipt of the r motor has recognized a sent DiSEqC command, which w rotation of the motor to a certain position, or jus but the mo sent the receiver, from been has command The reason can be disturbances that interfere with another device that might be connected to the 2 the that means it steadily, orange glows recei L) The motor has a built-in DiSEqC antenna switch. The 2 the or are defined as commands for the LNB-A and the LNB-B currently selected input is indicated by the LED in the entire signal to the common output (the input. At applies to a the inactive opposite switch receive 6 degrees. The purpose of this is from reception wisatellites a LNB with linear H/V and circular R/L polarization SATEL LITE MOTOR SM3D22 PAGE 12
SATEL LITE MOTOR SM3D22 PAGE 11
!
or or pole, thus causing
Make Make sure that the dish
LNB 2 LNB 1 LNB
can mount the assembly on the mast. See the the See mast. the on the assembly mount can RECEIVER SATELLITE rn the receiver on, enable the DiSEqC 1,2 mode or or 1,2 mode DiSEqC the on, enable receiver rn the read you When supply. power the LNB and motor e
CONNECTING THE RECEIVERCONNECTING MOTOR THE THE AND
CAUTION: A dish not tightened material securely damage, injuries can to people slide or even off. off slide possibly cannot death. the mot IT. SECURE J) tu Then, figure. the in shown as cables the Connect th enable and receiver, the on function "GoToX" the you works, the motor how learn and instructions the section. following le lly
iver
have a a mast, a
- SIGN -
TELLITE TELLITE SETTING ON THE
re than 5° east (E) or west (W) of
re the satellite position in a program tellite HOT BIRD (see the table below); HOT
g. See the table below. table the See g. eiver eiver so that you will know how to rotate x 1.15 = Setting on the motor. motor. the on Setting = 1.15 x e e table below. You will search for and store the e that is the closest to your location's south.
rmula rmula given below for the southern-most satellite; figure). the In the receiver, the satellite positions are norma rrow rrow points precisely at the value on the motor sca te. te. Proceed as follows: by using the satellite rece pole at 1.15°W (west). 1.15°W at (west). pole recommendable to follow some logical sequence. sequence. logical some follow to recommendable orbit. satellite the track already will ntenna s given in the section »Installing the satellite on the satellite »Installing section in the s given ivers, ivers, therefore follow the receiver manual if you
ew of ew of
: if your mounting location is 14° E, choose the sa
Detailed vi Detailed at set motor the (west) 1.15°W PROGRAMMING PROGRAMMING THE SOUTHERN-MOST SATELLITE ON A THE WITH MOTOR DiSEqC1.2/2.2 RECEIVER
O) Please read the instructions for the use of the rec the motor to the left channel. a or (E), satellite a change and location, or to the right (W), sto The setting of positions satellite varies with rece receiver that supports the DiSEqC 1.2/2.2 protocol. is it so 50); 1 to from (e.g., numbers under stored First, select and program the southern-most satelli rotate first commands, the motor pole so that the a (ring) that has been calculated according to the fo then store the position under a number chosen in th instruction with the accordance in satellites other a the because signal« satellite a for searching and On your site, the southern-most CAUTION: the satellite southern-most satellite must is not be the mo wron be might setting the on or south, your location's FORMULA FOR THE CALCULATION OF THE SOUTHERN-MOST SA MOTOR: location) your of Longitude – longitude (Satellite SIGN + the use (W) For west EXAMPLE motor the set to have will you so 13°E, at is BIRD (see +1.15 1.15 = x +1 = (-14) – (-13) means: This the use (E) For east SATEL LITE MOTOR SM3D22 PAGE 14 r r C C of of SATEL LITE MOTOR SM3D22 PAGE 13 he irst irst low s to ome ome cks. cks. If tenna.
ever ever you byting 6
1
) OR OR THE SATELLITE SIGNAL). This will uthernmost uthernmost satellite (see the section ME«, call satellite 00, go to 0, etc. 00, to go satellite ME«, call
otor. otor. The motor, in turn, rotates so that it
TRA) TRA) on the basis of your location latitude and e e changed by internal settings according to the erates in the following manner: the receiver sends this computed value by using DiSEqC o o your favorite satellite, or a satellite outside t motion. in ports ports it, too. There exist other names, e.g., DiSEq switch way: is the f in the following connect used 1 ase of satellites, which is usually provided with marked LNB-A is selected at the receiver, the moto n from several satellites, and the other input to s receiver. to the section. the following ignore can you , your your location on the Earth. This will work on one he he other LNB. In this case the LED indicator will g om the LNB1 input to the receiver, the satellite ha sho and interferences electric to external due tion a the other LNB. other the a antenna should be set to LNB-B for the connection signed, the motor will rotate inwill rotate shif the motor signed, its direction except for your favorite satellite from a fixed an "O". section lowing rest rest to your longitude (e.g., Hotbird). BE CAREFUL. the satellite focus will be on the first LNB. When
power supply is disconnected while the motor is in in is motor the while disconnected is power supply
1 1
Rotate East East Rotate West Rotate GotoX function) (the degrees by satellite a Call the NN by location satellite a Call NN for satellite position current the Store east movement the Limit west movement the Limit range (full movement limitations movement the Clear motor the stop – unconditionally Stop LNB other the to Switch ² reset – motor position starting the to Go
»HO are: names Other cable). coaxial the out (plug
MOTOR CONTROL BY USING THE DiSEqC THE BYUSING CONTROL COMMANDS MOTOR 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) FUNCTIONTHE BYUSING CONTROL»GoToX« MOTOR
The The operation is as follows: whenever the satellite will rotate in the direction of this satellite, and to which a select the other, satellite is LNB-B, as degrees, so that the satellite will be focused on t will vi be satellite the from Now reception orange. The default shift setting is supplier. your six with check – wish please customer's degrees, and can b the can The angle Then, shift also zero be degrees. input to the LNB of a rotating antenna for receptio other – a fixed antenna for the quick motor range. switch-over In this case, to connect t the signal fr be set to LNB-A; this applies to all the satellites On the receiver, your favorite satellite on a fixed antenna fixed the from signal – the input LNB2 the M) commands: DiSEqC following the recognizes motor The Notes: is motor the while executed not is command The ¹ - posi a of the state loses motor the when it Use ² - the motor's if achieved is effect same The motion N) You can only use this function is your receiver sup functions of these one have you If etc. 1.3, USALS, This function requires no programming at all. computes the It coordinates for any SATELLITE (e.g. AS op longitude that you have previously entered; then communication via it the coaxial cable to the SM3D22 points m precisely at such a satellite, depending on condition, i.e., that the receiver contains a receivers. modern datab When setting the INSTALLING antenna THE SATELLITE ON A MAST, AND SEARCHING dish F you be a satellite in will the receiver list that is the nea need your fol the receiver, skip the on function this use you so
n st st by by he ing the The The can
lf.
You can also
.
ption ption quality are
under a number different and and not by changing the motor tilt.
you should not be satisfied with the fore, check up at web pages satellite. each for equencies or in a the "rough" setting. But if you use the e basis of which you will know which the following additional steps: steps: additional following the most satellite signal. satellite most
nd west satellites. First point the receiver at at the receiver First satellites. point west nd a minimum dish rotating east/west. If – on rotating – east/west. If on dish minimum a rotating ition ition via the receiver under the number indicated i ion ion angle, fac the input LNB (over of h in the paper) front or direction. west the in same do the Then limit. ion you have set the elevation in the beginning (again f signal reception (the picture is sparkling). You tellites by the longitude from the easternmost to t ill ill be easier. Horizontal alignment should be made h an analog receiver we recommend that you decrease you that we recommend receiver analog an h easier. alignment optimal making
. . A digital receiver and its indicator of the rece (LNB1) (LNB1)
PRIMARY LNB LNB PRIMARY and not by rotating the motor pole or the dish itse SIGNAL SET TO TO SET SIGNAL
do not forget do forget not that you tohave each store satellite TO SET THE THE TO SET SOUTHERN YOU SATELLITE, ONLY SHOULD MOTOR THE ROTATE POLE THE ON SOUTH THE TOWARD
very useful tools for the precise dish setting; wit dish setting; the precise for tools useful very or increase the dish elevation angle to the limit o an clot (a by damp obstacle a do placing trick also deteriorates, reception the dish);result, a as the Caution: it is the satellite program schedule on th satellite (channel) you are actually viewing. fr and schedules program all There contains that magazine If you use the function, »GoToX« you have finished to take have you control, location 2.2 1.2 / DiSEqC a east both programming and for searching start You next east satellite (see the table, and sort the sa by strength signal for the check and westernmost), the dish – the signal deteriorates, program the pos rotat motor reachyou the until Continue table. the CAUTION: numbers. satellite the change
If If you have a dish specially adapted for the motor, a value on the motor scale), so satellite finding w rotating the motor on the mast, elevation is corrected by adjusting the dish elevat southern- the is received signal the that Make sure The accuracy of the alignment is very important and first picture you get on your TV set SATEL LITE MOTOR SM3D22 PAGE 16
SATEL LITE MOTOR SM3D22 PAGE 15
Position
Thor Thor 0,8W PAS PAS 43W 58W Amos Amos 4W Nilesat Nilesat 7W Satellite Eutelsat Intelsat Eutelsat 12.5W 31.5W Intelsat 36E Intelsat 50W Intelsat 53W 4/7 PAS 62E 68.5E
25 26 27 28 29 30 No. receiver
mewhere mewhere in e mounting atellite atellite (see
h elevation up- h elevation orbit. p of Position and search for gnal. When you hten hten the screws arter arter of a degree e e deviations due to make sure make the mast gnal meter on their satellite numbers, assign them in accordance with e e numbers at all, in which case satellite names are
setting easier for you.
table below and the following section. section. the following and below table .
PAS 1PAS 45W Telstar Telstar 37.5W 2 Astra Telstar 28.2E 15W Satellite Hispasat 30W Arabsat 3A Arabsat 26E 2B Arabsat 1B Turksat 30.5E 1C Turksat 31.3E 42E Intelsat 803 Intelsat 27.5W 601 Intelsat 34.5W Kopernicus 3 Kopernicus 23.5E
13 14 15 16 17 18 19 20 21 22 23 24 No.
13E
Position
Sirius Sirius 5E Astra 1 Astra 19.2E Satellite Bird Hot Eutelsat F3 Eutelsat F2 Eutelsat F4 Eutelsat 16E 10E 7E Telecom 2C Telecom 707 Intelsat 3E 2A Telecom 1W 705 Intelsat 8W 18W Telecom 2BD 2BD Telecom 5W NSSK, Intelsat Intelsat NSSK, 21.5W
INSTALLING INSTALLING THE THEFORSIGNAL SEARCHING SATELLITE SATELLITE ON A MAST, AND
1 2 3 4 5 6 7 8 9 10 11 12 To search for and program other satellites, see the see satellites, other program and for search To No. If the receiver is not provided with pre-programmed the table above. Some receivers do not use satellit irrelevant is above table the and positions as used P) the motor mounting and the Before a dish onto mast, is vertically plumb. Even (inclination of a 0.5 cm deviation at a of height of only 1 required. be will corrections which m) a may caus qu Using a satellite finder/signal meter will make the Anyway, the latest receivers are provided with menu. a si First, using your receiver call your the previous two southernmost sections). When the motor s stops so the middle, hold the motor, loosen the screws of bracket, look th in the receive direction of the dish, dis and left-right, system the theby moving signal down. The movement should be VERY slow because the requires a few to tens of a process milliseconds si find a signal, set it to optimum reception, and tig to to the reception the set you have Now carefully. he
have have
There can be five five be can There
ft ft (east), viewing from the rear (even ght ght (west), viewing from the rear (even way). this it and fix it lean now way). this it and fix it lean now an obstruction while being sent to the ncrease ncrease the dish elevation – set a bigger reduce the dish elevation – set a smaller or or the motor does not get loose, thus disabled the DiSEqC 1.2/2.2 mode. mode. 1.2/2.2 DiSEqC the disabled a new outermost point, and all the satellites on. move not does and point same the at nmost satellite as well. as satellite nmost might be broken, or there is a short circuit in e positions persist. The reason might be an first step to be taken is is taken be to step first have occurred in the satellite receiver as wellas – receiver satellite in the occurred have motor the rotated or has the wind point, ermost rotate to the outermost position. Remove the or the mast itself has rotated. Do not correct t likely, these satellite positions have been re- outermost satellites until you get satisfactory ew point. le; everything seems all right with regard to the t move. move. t not fall down. The set-up of isyour system receiver out of the mains for a minute, and then motor to a satellite position not having been
cted outermost (HOME) point. (HOME) point. outermost cted turning the motor to its original position. If you position. its the motor original to turning when leaning the mast or dish back (away from the them. used have you if or cloth paper the ove 4. item at described as do tor, - - when leaning the mast or the dish forth (toward t is too high. high. too is low. too is own. your on problem the remedy to pt
Lean Lean the mast with the motor slightly toward the ri must you plumb, vertically been has mast the though Lean the mast with the motor slightly toward must you plumb, vertically the been has mast the though le job. excellent an done have You Congratulations!
obstruction preventing the dish rotation to out to the rotation the dish preventing obstruction together with the dish. When outermost point, the the motor recognizes the dish point as is halted n by to this relative but more, once to positioned are All the satellite positions deviate by an equal ang above. item the see – please scale motor Certain satellite positions only are incorrect. Mos mistake. by programmed satellites. positioned wrongly the Re-program - stopping keeps it manually, motor the rotating When
TROUBLESHOOTING the correctly, operate not does motor the Whenever sele the to it sending i.e., motor, the resetting - - If the motor does not respond, plug the satellite again. in it plug no will 1, the motor item from steps taking Despite - between The connection the receiver and the motor may error An F connectors. one of or the LNB in the or supply power the LNB off switched have you maybe Even after you have reset the motor, wrong satellit
- - Reset the motor again and mo the check rotated has wind the any; if if obstruction, to see if it can 4.) - Obviously, the motor has been rotated on the mast by re but programming, by satellites to positioning already "corrected" any of the position. motor optimum an get to yet "corrected" positions, align the 5.) 6.) 3.) 3.) Repeat steps from items 1 and 2 with the wester the with and 2 1 items from steps 3.) Repeat combinations. result basic A) The dish is "too low" at both outermost points - improves. reception the satellite), angle. B) The dish is "too high" at both points outermost improves. reception the satellite), Reduce the motor tilt – set a smaller angle, and i angle. one west and the low, too is satellite east C) The Increase the motor tilt – set a bigger angle, and one west the and high, too is satellite east D) The reception. optimum have points outermost E) Both Correct and repeat the procedure of to rem forget not do completed, tuning The checking results. up the Remember: firmly secure the bolts so that the dish losing the signal and or the thatsettings, it does finished. now R) attem first operation, the in occur error an Should 1.) 2.) SATEL LITE MOTOR SM3D22 PAGE 18
o o e n. n. SATEL LITE MOTOR SM3D22 PAGE 17 to ed will
- by
tes the the tes et, the
The easiest easiest The
. .
This This is a satellite as close as
atellite. atellite.
W 35° 35° 35° on for the aligned east satellite. aligned for the on
nger nger signal. Never choose an obsolete inclined W W W e them with those described below. those with described them e deviations deviations will be slightly bigger, so fine tuning h h toward the satellite or - if this is not possible ore use the tricks described in the previous sectio uck, positioning uck, to positioning the south was precise enough, s This is a high-precision job for a person with som If the outermost satellite has a weak signal, we
instrument or a reception quality indicator provid is nothing detached moved; or actually all haveyou
error affects the outermost (east and west) satelli and (east outermost the affects error finder. atellite rop rop in the quality of analog reception on your TV s not causing a permanent deformation a permanent not causing
0° 0° 0° 0° 35° E E E E A C B D 35° 35° 35° 35°
FINE TUNING TUNING FINE On the satellite receiver, select the easternmost s
Q) If you followed the instructions and you had some l the major part of the job is now done. Otherwise, longer. take Any all the angles. of setting the up check First most, and results in a wrong dish elevation angle. s simple least a at with equipped skills, technical 1.) possible to the outermost motorrecommend that you rotation select limit. a nearer one, GLOSSARY). with the see (please satellite a stro up the elevati to dish check is 2.) Thestep second way to do this is by leaning the mast back and fort the dish leaning itself. With leaning this minimum dish, mast or the of bending minimum a is do This job will be difficult to accomplish without an with virtually all digital receivers. To notice a d mast or the dish has to be leant a long way, theref compar to obtained results the memorize or down Put
SATRACER_SW_SM3D22-V3-ENG_210205 SATRACER_SW_SM3D22-V3-ENG_210205
85 3831063911
SATEL LITE MOTOR SM3D22 PAGE 20
al al 3 3 SATEL LITE MOTOR SM3D22 PAGE 19 .... 11 ...... 9 ...... 12 ...... 12 ...... 6 ...... 7 ...... 1 ...... 5 ...... 18 ...... 19 ...... 8 ...... 5 ...... 17 ...... 5 ...... WITH WITH THE DiSEqC 1.2/2.2
...... 14 E...... 9 DE...... 4 N...... OR THE SATELLITE SIGNAL SATELLITE OR THE ...... 15 ...... 1 ...... 1 ......
ellite ellite receiver does not supply the same ......
...... time. time. eset eset the motor (send it to the outermost – HOME ...... on on or have problems installing it, call the Technic last pages. We will be pleased to provide you with ......
on, we congratulate you. you. we congratulate on, ......
......
Due Due to horizontal or vertical polarization, condition normal a is this so times, all at voltage the sat THE MEANING OF THE MOTOR FUNCTIONS...... MOTOR THE OF THE MEANING TROUBLESHOOTING ...... TABLE OF CONTENTS...... OF TABLE KIT CONTENTS AND TOOLS REQUIRED FOR THE INSTALLATIO FOR THE REQUIRED TOOLS AND CONTENTS KIT DESCRIPTION...... SAFETY PRECAUTIONS...... SAFETY GLOSSARY...... LOCATION INSTALLATION THE SELECTING ...... ASSEMBLY CABLE CONNECTING ...... ASSEMBLY...... MOTOR SETTING THE SCALE ON THE MOTOR CLAMP TO YOUR LATITU YOUR TO CLAMP MOTOR THE ON SCALE THE SETTING POLE MOTOR THE ON THE DISH MOUNTING ...... MOTOR THE AND RECEIVER THE CONNECTING ...... INTERNAL ANTENNA SWITCH IN THE MOTOR...... IN SWITCH ANTENNA INTERNAL COMMANDSDiSEqC THE USING BY CONTROL MOTOR ...... MOTOR CONTROL BY USING THE »GoToX« FUNCTION»GoToX« THE USING BY CONTROL MOTOR ...... PROGRAMMING THE SOUTHERN-MOST SATELLITE ON A MOTOR F SEARCHING AND MAST, A ON THE SATELLITE INSTALLING TUNING...... FINE
- - Most likely, there is a micro-controller error; r point). the all speed the same at rotate not does dish The - CONTENTS OF TABLE
A) B) C) D) E) F) G) H) I) J) K) L) M) N) O) RECEIVER...... P) Q) R) S) 7.) End. customer, Dear If you were not able to put the system into operati Assistance phone as indicated on the first and the information. further satisfacti to your system the installed have you If supplier. Your S) MOTOR SATELLITE