APPENDIX 1D Satellite Dish Specifications

ROVER PIPELINE PROJECT Resource Report 1 – Project Description

APPENDIX 1D

Satellite Dish Specifications

February 2015 Receive/Transmit Series 1134

1.2M KU-BAND RX/TX SERIES 1134

Prodelin Corporation is the world’s largest manufacturer of Key Features Rx/Tx VSAT antennas. We have the broadest product line in the · IntelSat approval number industry including Receive Only, IAO45A00 Rx/Tx and Rural Telephony · AsiaSat approved antenna systems. Prodelin offers nineteen antenna sizes, 47cm to · EutelSat VSAT type 4.5M. Prodelin is the leader in approval obtaining type certifications and Back View approvals for Intelsat, AsiaSat 1.2M Rx/Tx · ETSI Certification and Eutelsat. Prodelin antennas provide the best quality in the · New optics for low cross-pol market due to the sophisticated, compliance precision SMC compression molding process technology. · Precision compression molded offset reflector Prodelin provides the best value antenna solution to the market · Low cost shipping & easy with competitive prices, the Option local handling highest quality products and Feed Horn w/ OMT & superb engineering support. Transmit Reject Filter · Simplified one-man Prodelin is ISO registered, installation - less than one KEMA # 70022.01. Prodelin - hour assembly The Market Leader in VSAT Antennas. Receive/Transmit Series 1134

Electrical Series 1134 Ku-Band Antenna Size 1.2 M (47 in.) Operating Frequency (GHz) Receive 10.95 - 12.75 GHz Transmit 13.75 - 14.5 GHz 1.2M KU-BAND Midband Gain ( + .2dB) Receive 41.5 dBi Transmit 43.0 dBi Antenna Noise Temperature 20° elevation 46 K RX/TX 30° elevation 43 K Sidelobe Envelope, Co-Pol (dBi) 1° < θ < 20° 29-25 Log θ dBi 20° < θ < 26.3° - 3.5 dBi SERIES 26.3° < θ < 48° 32 -25 Log θ dBi 48° < θ -10 dBi (averaged) Cross-Polarization Within 1 dB contour -30 dB Max. Any Angle off Axis -25 dB Max. 1134 VSWR 1.3:1 Max. Mechanical Reflector Material Glass Fiber Reinforced Polyester SMC Antenna Optics Prime Focus, Offset Feed Mast Pipe Size 2 1/2" SCH 40 Pipe (2.88" OD) 73.2 mm. Elevation Adjustment Range 5° to 90° Continuous Fine Adjustment Azimuth Adjustment Range + 20° Fine, 360° Continuous Mount Type Elevation over Azimuth Shipping Specifications 90 lbs. (41 kg.) Environmental Performance Wind Loading Operational 50 mph (80 km/h) Survival 125 mph (201 km/h) Temperature Operational -40° to 140° F (-40° to 60° C) Survival -50° to 160° F (-46° to 71° C) Rain Operational 1/2" /hr Survival 2" /hr Ice Operational ------Survival 1/2" radial Atmospheric Conditions Salt, Pollutants and Contaminants as Encountered in Coastal and Industrial Areas Solar Radiation 360 BTU/h/ft2

© Copyright 2000 Prodelin, a TriPoint Global Company. All product specifications subject to change without notice. 5002-354 (5-2000) The Prodelin logo is a trademark of TriPoint Global. Assembly Instructions 8001014-01S

1.2 m Rear Brace Installation This instruction sheet supplements the feed leg for Type 125 Antenna Systems assembly notes that are in Manual 8001014-01

Important: Perform these steps prior to completing feed leg installation (page 4 of 8001014-01)

1) Install Left Hand and Right Hand rear braces between the az/el cap mount and the sides of the reflector as shown. Secure the slotted end of each brace to the az/el mount with M6 x 16 mm screw, star washer, flat washer, lock washer, and nut. With this hardware loose, temporarily secure the reflector end of brace to the rim of the dish with M6 x 20 mm screw and nut. Tighten the reflector end hardware (snug tight only), and then tighten the az/el hardware fully at this time.

2) Proceed to feed leg installation as described in the main manual. Install the side legs first, by removing the nut and attaching the leg and securing with lock washer and nut.

Reflector

Side Feed Leg

Right Rear Brace

M6 Flat M6 Lock Bottom Feed Leg Washer Washer Side (2 Places) (2 Place4-- M6 Hex Nut Feed Leg (2 Places)

N — Right Rear Brace

M6 x 20 mm Screw (2 Places)

Left Rear Brace Az/E1 Cap Mount

Left Rear Brace M6 Lock M6 Hex Nut Washer (2 Places) (2 Places)

M6 Star Washer (2 Places) M6 x 16 mm Hex Bolt (2 Places)

Sky Global Telephone: +1-919-934-9711 Printed in the U.S.A. 1315 Industrial Park Drive Smithfield, NC 27577 Internet: www.skywareglobal.com 04/11 8001014-01S Rev D EC-01063 Fcl :k•111g VAIN k

Pier Foundations Deep Frost Line Foundations

Ground Pole Must Be 73 cm or 7.6 cm Vertical in All Directions 73 cm or 76 cm (2.88" or 3.00" O.D.) -Is- -4- (2.88" or 3.00" O.D.) at Top

25 mm to 51 mm (1" to 2") t slope For water run-off Bubble I 91.4 cm max. Level (36") to 51 mm 182.9 cm (1" to 2") slope t 91.4 cm max. (72" Grade for water run-off (361 NOTE: 182.9 cm 127 cm (50") may (721 Grade be increased to frost I line. Concrete and length of rebar will increase accordingly.

#3 rebar x .46 m (18") Insert through 51 mm hole in tube and center. Minimum (2 ") Below #3 rebar Diameter Frost Line x diameter Milum Below #3 rebar x .6 m (241 of pier. Insert through Diameter Frost Line at 60- apart (See note) hole in tube and center.

Bottom View

Pier Foundations Deep Frost Line Foundations EXPOSURE B EXPOSURE C EXPOSURE B EXPOSURE C WIND VEL DIME D CONC VOL DIM D CONC VOL DIM D CONC VOL D CONC VOL GROUND km/h (mph) cm (in) m3 (ft3) cm (in) m3 (ft3) cm (in) m3 (ft3) cm (in) m3 (PI POLE 96 cm 161 (100) 25 (10) 0.05 (1.8) 38 (15) 0.11 (4.0) 18(7) 0.03(1.2) 25 (10) 0.07 (2.4) A, B or C Antenna 201 (125) 36 (14) 0.10 (3.5) 51 (20) 0.20 (72) 23 (9) 0.05 (1.9) 36 (14) 0.13 (4.7) A, B or C 1.2 m 161 (100) 30 (12) 0.08 (2.9) 46 (18) 0.18 (6.5) 20 (8) 0.05 (1.6) 33 (13) 0.12 (4.2) A ,B orC Antenna 201 (125) 43 (17) 0.17 (5.9) 61 (24) 0.33 (11.5) 30 (12) 0.10 (3.6) 48 (19) 0.25 (9.0)

POLE SPECIFICATIONS: Ground Pole "A" 2-1/2 Schedule 40 Steel ASTM A53 Pipe (73 mm x 5 mm Wall/2.88" OD x .203" Wall) Ground Pole "B" 3.0" OD x 9 Gauge (.148" Wall) Steel ASTM A501 Pipe (76 mm OD x 3.8 mm Wall) Ground Pole "C" 2-1/2 Schedule 80 Steel ASTM A53 Pipe (73 mm x 7 mm Wall/2.88" OD x .276" Wall)

NOTE: 1. 'Poles are not supplied (purchase locally to above specifications) and must be field drilled 5/8" diameter for M10 #3 rebar, drilled 5.55 mm (.218") for 1/4-20 self tapping grounding screw and galvanized or painted for protection. 2. Pole and foundation design based on the following criteria: a. Uniform building code Exposure B or C wind loading. b. Vertical soil pressure of 13790 kPa (2000 pounds per square foot). c. Lateral soil pressure of 2758 kPa (400 pounds per square foot). d. Concrete compressive strength of 17.2 MPa (2500 pounds per square inch) in 28 days. 3. See page 6 for grounding recommendations.

CAUTION: The foundation design shown does not represent an appropriate design for any specific locality. Soil conditions vary and may not meet design criteria given in Note 2. Consult a local professional engineer to determine your soil conditions and appropriate foundation.

3 ASSEMBLY AND INSTALLATION

Back View Bottom View Open Open Installing Az/EI Cap Mount Onto Pole Side Side of Square Nut (Factory Preset) of Pipe Inner The az/el cap is factory pre assembled. No Clamp Sleeve assembly is required. Before installing az/el cap Azimuth Azimuth Locking Locking onto pole, installation mount should be in place. Hex Nut Hex Nut Loosen (3) az/el locking nuts on pipe clamp. fl Install az/el cap onto pole. If using 2 7/8" ground pole, ensure that the inner sleeve is inserted and that the open side is aligned with -- -- the open side of the pipe clamp (see Bottom View). If using 3.00" ground pole, remove inner sleeve on pipe clamp and discard it. Position the az/el cap in approximate azimuth setting and Detail of Pipe Clamp equally tighten (3) clamp nuts so that cap is held Hex and Inner Sleeve stationary on pole, but can be swiveled with Clamp Nut Azimuth Note: Pipe Clamp and slight pressure. Tighten to approximately (3 Places) Square Nut Locking Inner Sleeve Should 2.7 N-m (2 ft-lb ). (Factory Preset) Hex Nut be Aligned as Shown

(19 0 a° 0 Hex Nut (4 Places) Lock Washer (4 Places) Assembling Reflector Onto Az/EI Cap Mount lk• Install four M8 x 60 mm plow bolts into holes in reflector face. Lift reflector and insert exposed portion of bolt into holes into Az/EI mount flange. Install 4 lock washers and hex nuts on bolts. Tighten and torque to 15 N-m (11 ft-lb). Do not over tighten. Overtightening M8 x 60 mm a me) bolts may damage reflector. Press fit hole plugs in remaining four Plow Bolts unused holes of the reflector. (4 Places) IMPORTANT: Note orientation of feed leg holes in reflector rim. Top of —Hole Plugs Az/E) reflector does NOT have feed leg hole. Cap Mount (4 Places) Installation 0 ° 0 Reflector Pole

Feed Leg Installation NOTE: long formed end of side feed leg attaches to the reflector rim, short formed end to side of feed support junction block. Assemble bottom feed leg to bottom of reflector rim. From the inside of reflector rim, assemble flat washer to the M6 x 16 mm hex bolt. Insert bolt through hole in rim and attach bottom feed leg. Secure with lock washer and hex nut. NOTE: Bottom feed leg is the one with a slight bend and a lance on one end. It is shorter than the side feed legs. Leave all hardware loose. Insert bottom feed leg end with lance into socket hole in center of feed support terminal. Twist to engage lances. Attach left and right feed support legs to feed support junction block, securing with M6 x 16 mm hex bolts and lock washers. Refer to instruction to assemble feed assembly and outdoor electronics to junction block. Tighten and torque all hardware to junction block and reflector to 5.4 N-m (4 ft-lb). Tighten two screws in junction block socket equally.

Flat Washer Flat Washer Hex Nut M6 x 16 mm Lock Washer M6 x 16 mm Hex Bolt Hex Bolt M6 x 16 mm Lock Washer Hex Bolt o Lock Washer Hex Nut Lock Washer

M6 x 16 mm Hex Bolt 4%141&O Flat Junction Washer Block

Bottom Lock Hex Nut Feed Leg 4 Washer TENNA ALIGNMENT PROCEDURE

Satellite Alignment Alignment with the satellite is obtained by setting polarization, elevation, and azimuth. Charts are provided in this manual to determine the values for your earth station antenna site. "AL" is the difference between the earth station antenna site longitude and the satellite longitude. Use "AL" and your earth station latitude to obtain polarization, elevation or azimuth setting.

Polarization of Feed Loosen feed Horn clamp bolts and turn feed clockwise or counterclockwise, depending on being east or west of the satellite as shown on Chart 1. For coarse Clamp setting, align marks-on the horn scale. Polarization chart assumes antenna system Bolt polarization is transmit vertical and satellite vertical Pol is perpendicular to plane of geostationary arc. For horizontal transmit of antenna, feed must be rotated 90° from values shown. (Starting point for polarization adjustment is 0°, as shown. Use Alignment a signal strength measuring device for final polarization setting and tighten horn Mark clamp bolts to 5.4 N-m (4 ft-lb).

Elevation - Initial Setting Elevation Alignment Arrow Use Chart 2 and determine your elevation setting. Loosen elevation locking bolts, located in curved slots, on both sides. Turn elevation adjustment bolt clockwise to decrease elevation or counterclockwise to increase elevation. Position the elevation alignment arrow with the appropriate mark on the housing at the desired elevation reading. Scale is in 1 degree increments. This Elevation will be an approximate setting. Snug tighten elevation locking Adjustment bolts. (Finger tighten only). Bolt Elevation Locking Bolts (Both Sides)

Azimuth - Initial Setting Square Nut (Factory Preset) Refer to the azimuth value determined on Azimuth Compass Ll Azimuth chart 3. Values in chart must be adjusted Locking Hex Nut \`-./ Locking for magnetic deviation for your location Hex Nut for correct compass reading. Rotate the reflector and az/el mount, on the pipe, Azimuth pointing it to the compass reading for Locking Hex Nut your location and satellite. Sweep in • Rotate Antenna azimuth for signal. If desired signal is not On Ground Tube located, increase or decrease elevation setting and repeat the azimuth sweep. Tighten progressively (1/8 turn each) all Azimuth three pipe clamp nuts. Repeat until 24 Square Nut N-m (18 ft-lb) torque is reached. (Factory Preset)

Az/EI Cap Mount Example Depicts Azimuth Heading To 171 . Bottom View (Azimuth ± Magnetic Deviation)

Elevation and Azimuth Fine Tuning Loosen (3) azimuth locking nuts. Note that the square Elevation nuts are factory preset, and should not be loosened or Fine Tuning tightened. Turn the azimuth fine tune bolt clockwise or counterclockwise for azimuth fine tuning. Do Use a signal strength measuring device to obtain the most accurate alignment and maximum antenna performance. Alternate between elevation and azimuth fine tuning to reach maximum signal strength, until Azimuth no improvement can be detected. Tighten and torque Fine Tuning all hardware, alternating sequence, until all bolts are equally torqued to 24 N-m (18 ft-lb). 5 GROUNDING PROCEDURE

INSTALLATION POLE MOUNT

Note: Grounding wire and hardware are not supplied for pole mount, trimast wall mount or non penetrating roof mount. Installation mount and associated hardware are not supplied. Ground Wire

Ground Wire with Ring Clip

Tooth 1/4" Washer Drilling Screw

Ground Lug

Coaxial Cables (To IDU) TRIMAST WALL MOUNT

Ground Wire with Ring Clip Ground Wire Ground Block (NEC Section .111, Ground M6 810-20) Secure M6 x 16 mm / Lug Lock Grounding Rod Clamp Hex Head Nut iet Screw Tooth Coaxial Washer TO GROUNDING Ground Wire Cables ROD (NEC Section (From ODU) 810-20)

Non Penetrating Roof Mount Note: Ground wire, secure clamp, grounding rod, coaxial cables and ground block are not supplied.

Ground Wire with Ring Clip IMPORTANT: All antenna sytems must be properly grounded. Refer to NEC (National Electric Code) Article 810, 820 and local M6 x 16 mm building codes for specific requirements. Typical grounding Tooth Self Tapping methods are shown as examples. Tighten all hardware securely to Washer Screw assure good continuity. Ground Lug

4sod 6uyunow Jo ig6!ag •xow „9E uo pasog au!! Japap papnpu! ION ain apoo 6u!pfinq wiopun way siopoj ainsodxa puo 4y6!aj_j c• apnpu! puo uoyDaiip puinn (uo Jo} sapioj wnwpcow pasaida, umoys sanion •uuatuo jo au!! Ja4uaD jo apojins 6ugunow way (u! jzE) ww gpa uo paspq Ow

ivawow 6u!tunpano = OW ivawow puo!sioi = lW

1016'0 g8gZ (811) LPZ (Z92-) O6£'£' (gLg) 16Z'Z LS OZ ODJOd 11339.13A = AA be esez (ze) cte (986.1 1807- (9891 190'E 11 09 01104 INUOZIJOH = H4 Icss'd SSVE loo) soy 1EV6-1 S61'17- IZZ8) 9g9'E 19 OS (oz6'z) V96E (LSE) V8V (6431 zie'c- (EV6) g61‘17 19 OV (9ZE'd LOSI izs (ILL-) e91'e- (110'1) 179L'17 LV oc (u9'e) 696V 47914 6Z9 (zotd asz's LE 7 108L'El Sttc 18814 Z99 etq' (ztti) cir's zz 01 (166T) 1017g (009) 819 (cc-) 95'1 - lgsz'il 911'g II 0 1/I ow Ai H A UMG9 .42aW H i (sounod-booj) w-N (sPunod) N quawow 03.110j saal6a0 uouonaig dty

kipoiaA Lidw SZL 40 spool puvAIDNAins ouualuy W Z'L

asod 6uyunow jo 4y6py .xow „92 uo pasoci au!! Ja4uaD papnpu!ION aio apop 6u!pfinci uuopun way vapoj ainsodxa puo .416taH Si g• apnpu! pun uotpaqp puim (uo ioj saaloj wnw!xow ivasaidad umoys gen/DA Duuquo jo aull Ja4uaD jo apojins. 6ullunow wolf (Li! 6.90 ww ZC6 uo 13°g°cl OW

4uaLuow 6u!turipano = OW WOWOW IOW:4510j = 101 (1t6) (17g) EL (EVV-) 1662) NCI. co OZ 03J0d 10D9 .10A —= A A (9ZZ'L) 099'1 (OL) co (ELS-) 617g'Z- (86E) OLL'l S8 09 apioA iNuozuoii = HA 6661 (06) ZZL scv'z- (8114 9Z i'z SL OS (u! 6 9E) (689'1) 98tZ (L01) grL leop-) siz'z- len) ser' 99 OV ww 106 (916' 1) Zog'Z (9z ILL lcii7-1 as' (z69) L9L'L 917 OE (91. rz) E98'L 881 6E-1 98Z'L - 1189) 9g0'E SE OZ alit (Ivi) 661 10g1 -1 L99- (101) sr Ce gZ 01 /711'E foci) coz (0Z-) 68- (LPL) ezeT SI 0 Ai H ow lw i Woos '1PoW (spunod--4004) W-N (sPunoci) N sivawow alloj SaaJ6a0.U01.10Aal3

44P° 19A tidw SZL 40 spool pum impuns ouuatuy LLD 96

CIVO1 GNIM 1VAIAZIfIS PARTS UST

NO. DESCRIPTION QTY.

96 cm Reflector or 1.2 m Reflector 2 Azimuth/Elevation Assembly 3 M8 x 60 mm Plow Bolt 4 4 M8 Stainless Steel Lock Washer -4__0:-.....r7"saVglIZ-,:=,—,r; Z 4 5 M8 x 1.25 Hex Head Nut 4 Plug Cap 4 7 96 cm or 1.2 m Side Feed Leg 2 8 96 cm or 1.2 m Bottom Feed leg 9 M6 x 16 Stainless Steel Hex Head Bolt 7 10 M6 Stainless Steel Lock Washer 5 11 M6 x 1 Hex Head Nut 3 12 Junction Block 13 Mounting Block Clamp 14 Feed Assembly 15 M6 Flat Washer 5