Dye Stain-A UV Dye Stain-A UV (12,2 M2/L)

Dye Stain-A UV Dye Stain-A UV (12,2 m2/L). Recoating will intensify color.

COMPOSITION & PROPERTIES Dye Stain-A UV is a fast-drying, semi-transparent, acetone-based dye stain. It can be reduced with AceThin (acetone).

TYPES 1. Product Name Dye Stain-A UV is available from the factory in 28 colors. Dye Stain-A UV Dye Stain-A UV colors can be reduced or intermixed

to achieve a wide variety of custom 2. Manufacturer colors. electric moisture meter to test all wood WOOD KOTE PRODUCTS INC surfaces. Do not proceed if reading is 8000 NE 14th Pl (97211) SIZES higher than 15% without written permission from architect/specifier. PO Box 17192 Dye Stain-A UV is sold in 16-fl oz Portland OR 97217 (473ml), 32-fl oz (946ml), 1-Gal Surface Preparation Tel: (800) 843-7666 (USA & Canada) (3,8L) HDPE plastic containers, 5- Sand all wood surfaces in the direction Tel: (503) 285-8371 Gal (19L) and 55 Gallon (208,5 L) of the wood grain with the appropriate Fax: (503) 285-8374 metal containers. abrasive grit specified on the finish [email protected] schedules (usually between 150-220 www.woodkote.com 4. Technical Data grit). Sand all wood surfaces until all

PHYSICAL PROPERTIES machine marks and glue are removed 3. Product Description and each species has achieved a BASIC USE See table 1 uniform smoothness without rough or burnished areas. Remove all sanding Dye Stain-A UV is intended for in-shop 5. Installation professional use only. It is a dye wood dust from the surfaces to be finished DS stain formulated to change the color of Complete installation specifications and from the work area. interior wood surfaces such as furniture, and recommendations are available casework, doors, trim, paneling and from the manufacturer. APPLICATION cabinets. Dye Stain-A UV is fade- Dye Stain-A UV is intended for spray resistant and its color retention is far PREPARATORY WORK application in-shop with equipment that superior than aniline stains. It may be Applicator Qualifications is appropriate for that purpose. Dye applied to bare or bleached wood. It is All work shall be performed by skilled Stain-A UV should be sprayed onto the compatible with a variety of other Wood tradesmen experienced in surface of the wood with an even Kote products. Please refer to the performing work of this type and motion in the direction of the wood Wood Kote Schedule of Product under the direction of a capable grain. Extreme care should be Compatibility and Recommended Dry foreman. exercised to apply the product evenly Times. Dye Stain-A UV complies with across the surface. If a lighter the US Environmental Protection Samples appearance is desired, the product can Agency (EPA) Volatile Organic For each finish system indicated at least be reduced with AceThin. If more Compound (VOC) emission two 8-1/2”x11” (19x24,6 cm) pieces intense color is desired, subsequent requirements for Architectural and should be provided for approval. If it is applications can be made in the same Industrial Maintenance coatings apparent conditions may allow manner. The product should be applied (effective 13Sep99) and California substantial variations, a sufficient in a manner that the application is SCAQMD Rule 1113 (effective number of samples should be created uniform in color, must be free of streaks, 14May99). to indicate the parameters of the blotches or other defects detrimental to variations. Those samples marked appearance or performance. ADVANTAGES “approved” by architect/specifier shall • Fast-drying serve as the standard for similar work • Will not raise wood grain throughout the project. • Deep appearance Inspection • UV resistance Verify all surfaces to be finished will be maintained within a temperature range COVERAGE of 45-80ºF (7-27ºC) during application One application of Dye Stain-A UV and drying period. Verify all surfaces to will cover approximately 500 sq ft/gal be finished are clean and dry. Use an

been tested over this product. The specifications provided herein. Unless applicator is responsible for testing Wood Kote warranties, in writing, suitability and performance for the specific products on an identified specific application. In all cases, Wood project, Wood Kote’s liability is limited to Kote strongly recommends testing the the replacement cost of the product. entire finish system on an equivalent The information provided herein is substrate before applying to the project. accurate to the best of Wood Kote’s Dye Stain-A UV should only be applied knowledge or obtained by Wood Kote by qualified professionals who have from sources believed by Wood Kote to read and understood this information. be accurate. Wood Kote Products Inc Before using any chemical, read its does not assume any legal label and Safety Data Sheet (SDS). responsibility for use or reliance upon Dye Stain-A UV this information. CLEAN UP Clean tools and surfaces using an 8. Maintenance absorbent cloth and AceThin. STORAGE

6. Availability & Cost Keep in the original containers tightly closed when not in use and stored

AVAILABILITY away from direct light at PRECAUTIONS Dye Stain-A UV is available through temperatures between 32-110ºF (0- Be certain that conditions allow for recognized Wood Kote retailers or 43ºC). adequate ventilation and pose no threat directly from the manufacturer. A list of fire or other health hazards. Dye of stocking dealers is available from CLEANING & REPAIR Stain-A UV is a penetrating dye and is the manufacturer and can be found Dye Stain-A UV is intended to be extremely difficult to remove once on the manufacturer’s web site. top-coated, and therefore, cannot be applied. It contains UV inhibitors but it is directly cleaned or repaired. not light fast and will change color with COST exposure to light. Dye Stain-A UV is a DISPOSAL wood stain and must be properly top- Cost information is available from DS coated with lacquer or polyurethane to recognized Wood Kote retailers or Dispose of only in accordance with achieve a complete wood finish. DO from the manufacturer. local, state and federal regulations. NOT use on surfaces that are not 7. Warranty uniformly sanded. This product has 9. Technical Services been tested on a very limited number of Dye Stain-A UV is sold without warranty Additional information is available substrates (and coatings). In addition, a except that Wood Kote guarantees that directly from the manufacturer and very limited number of coatings have the product is manufactured within the from the manufacturer’s web site.

10. Filing Systems • Wood Kote–Product Catalog Physical Properties Table 1 • Additional product information is available from the manufacturer Mfr No COLOR VOC gm/L FLASH PT www.woodkote.com 441A Light Brown Mahogany Exempt 1ºF (-17,2ºC) • 442A Medium Brown Mahogany Exempt 1ºF (-17,2ºC) 443A Cordovan Mahogany Exempt 1ºF (-17,2ºC) 444A Cherry Exempt 1ºF (-17,2ºC) 445A Amber Fruitwood Exempt 1ºF (-17,2ºC) 446A Golden Fruitwood Exempt 1ºF (-17,2ºC) 447A Jet Black Exempt 1ºF (-17,2ºC) 448A Light Red Mahogany Exempt 1ºF (-17,2ºC) 449A Medium Red Mahogany Exempt 1ºF (-17,2ºC) 450A Hickory Exempt 1ºF (-17,2ºC) 452A American Walnut Exempt 1ºF (-17,2ºC) 453A Medium Brown Walnut Exempt 1ºF (-17,2ºC) 454A Nutmeg Brown Exempt 1ºF (-17,2ºC) 455A Van Dyke Brown Exempt 1ºF (-17,2ºC) 456A Sea Blue Exempt 1ºF (-17,2ºC) 457A Brown Maple Exempt 1ºF (-17,2ºC) 458A Yellow Maple Exempt 1ºF (-17,2ºC) 459A Medium Wheat Exempt 1ºF (-17,2ºC) 460A Dark Green Exempt 1ºF (-17,2ºC) 461A Blood Red Exempt 1ºF (-17,2ºC) 462A Bright Red Exempt 1ºF (-17,2ºC) 463A Lemon Yellow Exempt 1ºF (-17,2ºC) 464A Light Orange Yellow Exempt 1ºF (-17,2ºC) 465A Red Exempt 1ºF (-17,2ºC) 466A Yellow Exempt 1ºF (-17,2ºC) 467A Orange Exempt 1ºF (-17,2ºC) 468A Blue Exempt 1ºF (-17,2ºC) 469A Brown Exempt 1ºF (-17,2ºC)

Wood Kote, Lite-N-Up, WoodPerfect, WoodBuddy, W-F-C, SprayLaq, KatLaq, Trans Kote, Jel'd Stain, Liqwid Stain, Dye Stain, Glaze Kote, BrushLaq, Jel'd Poly Kote, Ultra Poly Kote, Flagship, FloorEver, Clear and Clean, X-Link-R, MacroTint & MiniTint, Korrect-O, Perfecto-O, LaqFlat, PolyFlat, LaqAdd, LaqThin, WashThin, AceThin, PolySolvent, Sta-Wax, Lin Soap, C-U-2 are registered trademarks or trade-names of Wood Kote Products Inc.