GA-AB350-Gaming 3
User's Manual Rev. 1002 12ME-AB35GM3-1002R
For more product details, please visit GIGABYTE's website.
To reduce the impacts on global warming, the packaging materials of this product are recyclable and reusable. GIGABYTE works with you to protect the environment. Motherboard GA-AB350-Gaming 3
Motherboard GA-AB350-Gaming 3
Feb. 6, 2017
Feb. 6, 2017
Copyright © 2017 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission. For quick set-up of the product, read the Quick Installation Guide included with the product. In order to assist in the use of this product, carefully read the User's Manual. For product-related information, check on our website at: http://www.gigabyte.com Identifying Your Motherboard Revision The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information. Example: Table of Contents
GA-AB350-Gaming 3 Motherboard Layout...... 4
Chapter 1 Hardware Installation...... 5 1-1 Installation Precautions...... 5 1-2 Product Specifications...... 6 1-3 Installing the CPU...... 9 1-4 Installing the Memory...... 9 1-5 Installing an Expansion Card...... 10 1-6 Back Panel Connectors...... 10 1-7 Internal Connectors...... 12
Chapter 2 BIOS Setup...... 20 2-1 Startup Screen...... 21 2-2 M.I.T...... 21 2-3 System...... 25 2-4 BIOS...... 26 2-5 Peripherals...... 29 2-6 Chipset...... 31 2-7 Power...... 32 2-8 Save & Exit...... 34
Chapter 3 Appendix...... 35 3-1 Configuring a RAID Set...... 35 3-2 Drivers Installation...... 37
Regulatory Statements...... 38 Contact Us...... 40
- 3 - GA-AB350-Gaming 3 Motherboard Layout
ATX_12V CPU_FAN CPU_OPT KB_MS_USB3
DVI HDMI
Socket AM4 SYS_FAN2
USB_DAC ATX
R_USB31
USB30_LAN
AUDIO SYS_FAN1 LED_C1 M_BIOS 0 1 B_BIOS PCIEX1_1 GA-AB350-Gaming 3 DDR4_2 DDR4_3 DDR4_1 DDR4_4 ASATA3 Realtek® PCIEX16 GbE LAN
110 80 60 42 M2F_32G
AMD B350 BAT 2 3 PCIEX4 CODEC SATA3
PCIEX1_2 iTE® Super I/O SATA3 1 0 PCIEX1_3
SYS_FAN3_PUMP CLR_CMOS SPDIF_O CPU DRAM VGA BOOT
F_AUDIO LED_C2 TPM F_USB1 F_USB2 F_USB30 F_PANEL Box Contents 55 GA-AB350-Gaming 3 motherboard 55 Four SATA cables 55 Motherboard driver disk 55 I/O Shield 55 User's Manual 55 One G Connector 55 Quick Installation Guide 55 One RGB (RGBW) LED strip extension cable
* The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.
- 4 - Chapter 1 Hardware Installation 1-1 Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures: •• Prior to installation, make sure the chassis is suitable for the motherboard. •• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation. •• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components. •• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely. •• When handling the motherboard, avoid touching any metal leads or connectors. •• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity. •• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container. •• Before connecting or unplugging the power supply cable from the motherboard, make sure the power supply has been turned off. •• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard. •• Before using the product, please verify that all cables and power connectors of your hardware components are connected. •• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components. •• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing. •• Do not place the computer system on an uneven surface. •• Do not place the computer system in a high-temperature or wet environment. •• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user. •• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician. •• If you use an adapter, extension power cable, or power strip, ensure to consult with its installation and/or grounding instructions.
- 5 - 1-2 Product Specifications
CPU AM4 Socket: - AMD Ryzen™ processor - AMD 7th Generation A-series/Athlon™ processors (Go to GIGABYTE's website for the latest CPU support list.) Chipset AMD B350 Memory 4 x DDR4 DIMM sockets supporting up to 64 GB of system memory * Due to a Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than the size of the physical memory installed. Dual channel memory architecture Support for DDR4 2667(Note)/2400/2133 MHz memory modules Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in non-ECC mode) Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules Support for Extreme Memory Profile (XMP) memory modules (Go to GIGABYTE's website for the latest supported memory speeds and memory modules.) Onboard Integrated Graphics Processor: Graphics - 1 x DVI-D port, supporting a maximum resolution of 1920x1200@60 Hz * The DVI-D port does not support D-Sub connection by adapter. - 1 x HDMI port, supporting a maximum resolution of 4096x2160@24 Hz * Support for HDMI 1.4 version. - Maximum shared memory of 2 GB Audio Realtek® ALC1220 codec High Definition Audio 2/4/5.1/7.1-channel Support for S/PDIF Out LAN Realtek® GbE LAN chip (10/100/1000 Mbit) Expansion Slots 1 x PCI Express x16 slot, running at x16 (PCIEX16)(Note) * For optimum performance, if only one PCI Express graphics card is to be installed, be sure to install it in the PCIEX16 slot. (The PCIEX16 slot conforms to PCI Express 3.0 standard.) 1 x PCI Express x16 slot, running at x4 (PCIEX4) * The PCIEX4 slot shares bandwidth with the PCIEX1_2 and PCIEX1_3 slots. The PCIEX4 slot operates at up to x2 mode when the PCIEX1_2/PCIEX1_3 slot is populated. The PCIEX4 slot operates at up to x4 mode when both of the PCIEX1_2 and PCIEX1_3 slots are empty. 1 x PCI Express x16 slot, running at x1 (PCIEX1_3) 2 x PCI Express x1 slots (The PCIEX4 and PCI Express x1 slots conform to PCI Express 2.0 standard.)) Multi-Graphics Support for AMD Quad-GPU CrossFire™ and 2-Way AMD CrossFire™ technologies Technology Storage Interface 1 x M.2 connector (Socket 3, M key, type 2242/2260/2280/22110 SATA and PCIe x4 (Note)/x2 SSD support) 6 x SATA 6Gb/s connectors Support for RAID 0, RAID 1, and RAID 10 * Refer to "1-7 Internal Connectors," for the installation notices for the M.2 and SATA connectors. (Note) Actual support may vary by CPU. - 6 - USB Chipset: - 2 x USB 3.1 Gen 2 Type-A ports (red) on the back panel - 2 x USB 3.1 Gen 1 ports (available through the internal USB header) - 5 x USB 2.0/1.1 ports (1 port on the back panel, 4 ports available through the internal USB headers) CPU: - 4 x USB 3.1 Gen 1 ports on the back panel Internal 1 x 24-pin ATX main power connector Connectors 1 x 8-pin ATX 12V power connector 1 x M.2 Socket 3 connector 6 x SATA 6Gb/s connectors 1 x CPU fan header 1 x water cooling CPU fan header 2 x system fan headers 1 x system fan/water cooling pump header 1 x front panel header 1 x front panel audio header 1 x S/PDIF Out header 1 x USB 3.1 Gen 1 header 2 x USB 2.0/1.1 headers 1 x Trusted Platform Module (TPM) header 1 x CPU cooler LED strip/RGB LED strip extension cable header 1 x RGB (RGBW) LED strip extension cable header 1 x Clear CMOS jumper Back Panel 1 x PS/2 keyboard/mouse port Connectors 1 x DVI-D port 1 x HDMI port 4 x USB 3.1 Gen 1 ports 2 x USB 3.1 Gen 2 Type-A ports (red) 1 x USB 2.0/1.1 port 1 x RJ-45 port 1 x optical S/PDIF Out connector 5 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Line In, Line Out, Mic In) I/O Controller iTE® I/O Controller Chip Hardware Voltage detection Monitor Temperature detection Fan speed detection Overheating warning Fan fail warning Fan speed control * Whether the fan (pump) speed control function is supported will depend on the fan (pump) you install.
- 7 - BIOS 2 x 128 Mbit flash Use of licensed AMI UEFI BIOS Support for DualBIOS™ PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0 Unique Features Support for APP Center * Available applications in APP Center may vary by motherboard model. Supported functions of each application may also vary depending on motherboard specifications. - @BIOS - 3D OSD - AutoGreen - BIOS Setup - Cloud Station - Color Temperature - EasyTune - Fast Boot - Game Boost - ON/OFF Charge - RGB Fusion - Smart Backup - Smart Keyboard - Smart TimeLock - System Information Viewer - USB Blocker - USB DAC UP 2 - V-Tuner Support for Q-Flash Support for Xpress Install Bundled Norton® Internet Security (OEM version) Software cFosSpeed Operating Support for Windows 10 64-bit System Support for Windows 7 64-bit * Please download the "Windows USB Installation Tool" from GIGABYTE's website and install it before installing Windows 7. Form Factor ATX Form Factor; 30.5cm x 23.0cm
* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.
Please visit GIGABYTE's website Please visit the Support\Utility List for support lists of CPU, memory page on GIGABYTE's website to modules, SSDs, and M.2 devices.. download the latest version of apps.
- 8 - 1-3 Installing the CPU Read the following guidelines before you begin to install the CPU: •• Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest CPU support list.) •• Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage. •• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket.) •• Apply an even and thin layer of thermal grease on the surface of the CPU. •• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage of the CPU may occur. •• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals. If you wish to set the frequency beyond the standard specifications, please do so according to your hardware specifications including the CPU, graphics card, memory, hard drive, etc. Installing the CPU Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU. A Small Triangle Marking A Small Triangle Marking Denotes Pin One of the AM4 Socket AM4 CPU Socket Denotes CPU Pin One
1-4 Installing the Memory Read the following guidelines before you begin to install the memory: •• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest supported memory speeds and memory modules.) •• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage. •• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual Channel memory mode will double the original memory bandwidth. The four memory sockets are divided into two channels and each channel has two memory sockets as following: Channel A: DDR4_2, DDR4_4 Channel B: DDR4_1, DDR4_3
Please visit GIGABYTE's website for details on hardware installation.
- 9 - Dual Channel Memory Configurations Table DDR4_4 DDR4_2 DDR4_3 DDR4_1 Two Modules - - DS/SS - - DS/SS DS/SS - - DS/SS - - Four Modules DS/SS DS/SS DS/SS DS/SS (SS=Single-Sided, DS=Double-Sided, "- -"=No Memory) Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode. 1. Dual Channel mode cannot be enabled if only one memory module is installed. 2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used. For optimum performance, when enabling Dual Channel mode with two memory modules, we recommend that you install them in the DDR4_1 and DDR4_2 sockets.
1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: •• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card. •• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.
1-6 Back Panel Connectors
PS/2 Keyboard/Mouse Port Use this port to connect a PS/2 mouse or keyboard. USB 3.1 Gen 1 Port The USB 3.1 Gen 1 port supports the USB 3.1 Gen 1 specification and is compatible to the USB 2.0 specification. Use this port for USB devices. DVI-D Port (Note) The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200@60 Hz (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports DVI-D connection to this port. HDMI Port The HDMI port is HDCP compliant and supports Dolby TrueHD and DTS HD Master Audio formats. It also supports up to 192 KHz/24bit 8-channel LPCM audio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096x2160@24 Hz, but the actual resolutions supported are dependent on the monitor being used.
After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The item name may differ depending on your operating system.)
(Note) The DVI-D port does not support D-Sub connection by adapter. - 10 - USB 2.0/1.1 Port The USB port supports the USB 2.0/1.1 specification. You can connect a USB DAC to this port or use this port for USB devices. USB 3.1 Gen 2 Type-A Port (Red) The USB 3.1 Gen 2 Type-A port supports the USB 3.1 Gen 2 specification and is compatible to the USB 3.1 Gen 1 and USB 2.0 specification. Use this port for USB devices. RJ-45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.
Connection/ Connection/Speed LED: Activity LED: Speed LED Activity LED State Description State Description Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring Green 100 Mbps data rate Off No data transmission or receiving is occurring Off 10 Mbps data rate LAN Port Center/Subwoofer Speaker Out Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio configuration. Rear Speaker Out This jack can be used to connect rear speakers in a 4/5.1/7.1-channel audio configuration. Optical S/PDIF Out Connector This connector provides digital audio out to an external audio system that supports digital optical audio. Before using this feature, ensure that your audio system provides an optical digital audio in connector. Line In The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc. Line Out The line out jack. This jack supports audio amplifying function. For better sound quality, it is recommended that you connect your headphone/speaker to this jack (actual effects may vary by the device being used). Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers in a 4/5.1/7.1-channel audio configuration. Mic In The Mic in jack.
•• To enable or configure the audio amplifying function for the Line out jack, please access the HD Audio Manager application. •• If you want to install a Side Speaker, you need to retask either the Line in or Mic in jack to be Side Speaker out using the HD Audio Manager application. •• Please visit GIGABYTE's website for more audio software information. •• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard. •• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.
- 11 - 1-7 Internal Connectors
1 3 5
4
2 19
4 7
9 13
8 8 14
12 10 20 17 16 6 15 11 18
1) ATX_12V 11) F_PANEL 2) ATX 12) F_AUDIO 3) CPU_FAN 13) BAT 4) SYS_FAN1/2 14) CLR_CMOS 5) CPU_OPT 15) F_USB30 6) SYS_FAN3_PUMP 16) F_USB1/F_USB2 7) ASATA3 0/1 17) TPM 8) SATA3 0/1/2/3 18) CPU/VGA/DRAM/BOOT 9) M2F_32G 19) LED_C1 10) SPDIF_O 20) LED_C2
Read the following guidelines before connecting external devices: •• First make sure your devices are compliant with the connectors you wish to connect. •• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices. •• After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.
- 12 - G.QBOFM
G.QBOFM DEBUG PORT
DEBUG PORT G.QBOFM
G.QBOFM
1/2) ATX_12V/ATX (2x4 12V Power Connector and 2x12 Main Power Connector) With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned DEBUG off and all devices are properly installed. The power connector possesses a foolproof design. Connect the PORT power supply cable to the power connector in the correct orientation.
DEBUG PO RT The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start. To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.
ATX_12V: Pin No. Definition Pin No. Definition 1 GND (Only for 2x4-pin 12V) 5 +12V (Only for 2x4-pin 12V) 5 8 2 GND (Only for 2x4-pin 12V) 6 +12V (Only for 2x4-pin 12V) 1 4 3 GND 7 +12V ATX_12V 4 GND 8 +12V
ATX: 12 24 Pin No. Definition Pin No. Definition 1 3.3V 13 3.3V 2 3.3V 14 -12V 3 GND 15 GND 4 +5V 16 PS_ON (soft On/Off) 5 GND 17 GND 6 +5V 18 GND 7 GND 19 GND 8 Power Good 20 NC 9 5VSB (stand by +5V) 21 +5V 10 +12V 22 +5V 11 +12V (Only for 2x12-pin 23 +5V (Only for 2x12-pin ATX) 1 13 ATX) 12 3.3V (Only for 2x12-pin 24 GND (Only for 2x12-pin ATX) ATX) ATX
3/4) CPU_FAN/SYS_FAN1/2 (Fan Headers) All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.
1 Pin No. Definition 1 GND 2 Voltage Speed Control 1 1 3 Sense CPU_FAN SYS_FAN1 SYS_FAN2 4 PWM Speed Control •• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang. •• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.
- 13 -
RT PO
DEBUG DEBUG G.QBOFM G.QBOFM
G.QBOFM
DEBUG PORT
DEBUG PORT
5) CPU_OPT (Water Cooling CPU Fan Header) The fan header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design.
Pin No. Definition 1 1 GND 2 Voltage Speed Control 3 Sense 4 PWM Speed Control
6) SYS_FAN3_PUMP (System Fan/Water Cooling Pump Headers) G.QBOFM G.QBOFM The fan/pump headers are 4-pin. Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis. The headers also provides speed control for a water cooling pump, refer to Chapter 2, "BIOS Setup," "M.I.T.," for more information
Pin No. Definition 1 1 GND 2 Voltage Speed Control 3 Sense 4 PWM Speed Control
7/8) ASATA3 0/1, SATA3 0/1/2/3 (SATA 6Gb/s Connectors) The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connectorDEBUG supportsDEBUG a single SATA device. The SATA connectors support RAID 0, RAID 1, and RAID 10. ReferPORT to ChapterPO 3,RT "Configuring a RAID Set," for instructions on configuring a RAID array.
1 Pin No. Definition 1 GND
0 2 TXP ASATA3 3 TXN 1 G.QBOFM 4 GND 5 RXN 7 6 RXP 2 7 1
SATA3 7 GND PO RT DEBUG 3 7 1
1 7 SATA3 1 0 PO RT DEBUG
- 14 -
DEBUG PORT G.QBOFM G.QBOFM S S U
F_USB30 F_ U F_ F_