Applicable Codes and Standards
Total Page:16
File Type:pdf, Size:1020Kb
September 2013 1 The following list of Codes and Standards is intended to be indicative only of the extent to which guidance should be taken from internationally available Codes. This list will not be taken to constitute a complete and exhaustive reference. CODES & STANDARDS FOR PIPELINE/PIPING / MECHANICAL Reference Description PED 97/23/EC Pressure Equipment Directive API RP 1102 Steel Pipelines: Crossings of Railroads and Highways ASME B 31.8 Gas Transmission and Distribution Piping Systems EN 287-1 Qualification on test of welders. Fusion welding. Steels EN 288-9 Approval of welding procedures for metallic materials. Non-destructive testing – Qualification and certification of NDT personnel – EN 473 General principles EN 571-1 Non – Destructive Testing – Penetrant testing – General Principles EN 970 Non-destructive examination of fusion welds-visual examination Flanges and their joints. Circular flanges for pipes, valves, fittings and EN 1092-1 accessories, PN designated. Steel flanges. Non-destructive examination of welds. Penetrant testing of welds – EN 1289 Acceptance levels Non-destructive examination of welds. Magnetic particle examination of EN 1290 welds Non-destructive examination of welds. Magnetic particle examination of EN 1291 welds - Acceptance levels Non – Destructive Examination of welds – Radiographic examination of weld EN 1435 joints Flanges and their joints – Dimensions of gaskets for PN designated flanges – EN 1514-1 & -2 Part 1: Non-metallic flat gaskets with or without inserts, Part 2: Spiral wound gaskets for use with steel flanges 2 Flanges and their joints – Bolting – Part 3: Classification of bolt materials for steel flanges, class EN 1515-3 designated EN 1594 Gas Supply Systems – Pipelines - Maximum operating pressure over 16 bar - Functional Requirements EN 1712 Non-destructive testing of welds – Ultrasonic testing of welded joints - Acceptance levels EN 10160 Ultrasonic testing of steel flat product of thickness equal to or greater than 6 mm (reflection method) EN 10204 Material Certification and Identification Steel pipes for pipelines for combustible fluids – Technical delivery conditions – Part:2 Pipes for requirement EN 10208-2 class B EN 10253-2 Butt-welding pipe fittings. Non alloy and ferritic alloy steels with specific inspection requirements. EN 10274 Metallic Materials-Drop Weight teat test Steel tubes and fittings for on and offshore pipelines-Internal coating for the reduction of friction for EN 10301 conveyance of non-corrosive gas EN ISO 10497 Testing of valves - Fire type testing requirements Steel tubes for onshore and offshore pipelines. External liquid applied polyurethane and polyurethane- EN 10290 modified coatings. Cathodic protection – External organic coatings for the corrosion protection of buried or immersed steel EN 12068 pipelines used in conjunction with cathodic protection - Tapes and shrinkable materials Welding consumables – Quality requirements for manufacture, supply and distribution of consumables for EN 12074 welding and allied processes Gas supply systems. Pressure testing, commissioning and decommissioning procedures. Functional EN 12327 requirements Non destructive testing of welds – Evaluation of welded welds in steel, nickel, titanium and their alloys by EN 12517-1 radiography Acceptance levels. Flanges and their joints – Gaskets for class-designated flanges – Part 2: Spiral wound gaskets for use with steel EN 12560-2 flanges. Industrial valves. Valves for chemical and petrochemical process industry. Requirements EN 12569 and tests EN 12732 Gas Supply Systems – Welding steel pipe work – Functional requirements EN 13445 Unfired Pressure Vessels 3 EN 13480 Metallic industrial piping EN 13942 Petroleum and natural gas industries. Pipeline transportation systems. Pipeline valves EN 14141 Valves for natural gas transportation in pipelines-Performance requirements and tests Petroleum and Natural Gas Industries. Induction bends, fittings and flanges for pipeline transportation systems- EN 14870-1:2004 Part 1: Induction Bends Petroleum and Natural Gas Industries. Induction bends, fittings and flanges for pipeline transportation systems- EN 14870-2:2004 Part 2: Fittings Petroleum and Natural Gas Industries. Induction bends, fittings and flanges for pipeline transportation systems- EN 14870-3:2006 Part 3: Flanges Specification and qualification of welding procedures for metallic materials – Qualification based on tested welding EN ISO 15610 consumables Specification and qualification of welding procedures for metallic materials. Qualification based on previous EN ISO 15611 welding experience. Specification and qualification of welding procedures for metallic materials. Qualification by adoption of a standard EN ISO 15612 welding procedure. Specification and qualification of welding procedures for metallic materials – Qualification based on pre-production EN ISO 15613 welding test EN 15614-1 Specification and qualification of welding procedures for metallic materials. Welding procedure test EN ISO 8501-1 Preparation for steel substrates before Application of Paints and related Products EN 1714 Non-destructive testing of welds – Ultrasonic testing of welded joints EN ISO 15609-1 Specification and Approval of Welding Procedures for metallic Materials (formerly EN 288- Part 2) Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts, screws and studs – Part 2: ISO 898-1 & -2 Nuts with specified proof load values; coarse thread. EN ISO 2808 Paints and Varnishes – Determination of Film Thickness EN ISO 9001 Quality Management Systems – Requirements ISO 13443 Natural Gas – Standard reference conditions 4 EU LEGISLATION ATEX 94/9/EC Equipment and Protective Systems intended for use in Potentially Explosive Atmospheres. ATEX 100A Directive Safety of Apparatus ATEX 99/92/EC Safety of Installation. (ATEX 137) PED (97/23/EC) Pressure Equipment Directive CODES AND STANDARDS AGA 12 Cryptographic Protection of SCADA Communications ASME A269 Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service ASME B1.20.1 Pipe Threads, General Purpose EIA -359 Standard Colours for Colour Identification and Coding EIA RS 232C Interface between data terminal equipment employing serial binary data interchange EIA /TIA -455 Test Procedures for Fibre Optic Fibres, Cables, Transducers, Connecting and Terminating Devices EIA / TIA-598 Standard for Colour Coding of Fibre Optic Cables EIC CCI P/1 Instrument Installation Testing Procedure EN 837-1 Pressure Gauges-Part 1: Bourdon Tube EN 1594 Gas supply systems EN ISO-5210 Industrial Valves – Multi-turn Valve Actuator attachments EN ISO-5211 Industrial Valves – Part-turn Valve Actuator attachments EN 10143 Specification for continuously Hot-Dip Zinc Coated and Iron - Zinc Alloy Coated Steel EN 50019 Electrical apparatus for potentially explosive atmospheres - Increased safety "e" EN 50020 Electrical apparatus for potentially explosive atmospheres - Intrinsic safety "i" EN 50028 Electrical apparatus for potentially explosive atmospheres - Encapsulation "m" EN 50039 Electrical apparatus for potentially explosive atmospheres - Intrinsically safe electrical systems "i" EN 50086 Specification for conduit systems for cable management. General requirements EN 50173 Information technology — Generic cabling systems EN 50262 Cable glands for electrical installations EN 50267 Common test methods for cables under fire conditions. EN 60079 Specification for Electrical Apparatus for Explosive Gas Atmospheres - Electrical Installations in Hazardous Areas. EN 60228 Conductors of Insulated Cables 5 EN 60269 Low Voltage Fuses EN 60332 Tests on electric and optical fibre cables under fire conditions EN 60529 Classification for degrees of protection provided by enclosures (IP rating) EN 60617 Graphical symbols for diagrams Boxes and enclosures for electrical accessories for household and similar fixed electrical installations. Particular EN 60670 requirements for connecting boxes and enclosures EN 60793-1-1 Generic Specification for Optical Fibres. EN 60793-2-12 Product Specification for Optical Fibres. EN 60794-1 General Specification for Optical Fibre Cables. EN 60794-2 Product Specifications for Optical Fibre Cables. EN 61000 Electromagnetic Compatibility Functional Safety of Electrical/Electronic/Programmable Electronic Safety-Related Systems-Part 1: General EN 61508-1 Requirements Functional Safety of Electrical/Electronic/Programmable Electronic Safety-Related Systems-Part 2: Requirements for EN 61508-2 Electrical/Electronic/Programmable Electronic Safety-Related Systems EN 61515 Mineral insulated thermocouple cables and thermocouples EN 62040 Uninterruptible power supply systems Commissioning of Electrical, Instrumentation and Control Systems in the Process Industry-Specific Phase and EN 62337 milestones IEEE 730 Software Quality Assurance Plan IEEE 830 Software Requirement Specification IEEE 802.3 Standard CSMA/CD Media Access Control (Ethernet) IEEE 829 Software Test Documentation IEC 255-5 Electrical Insulation lEC 1218 Fibre optic-Safety guide. IEC 60050 Earthing and Protection Against Electric Shock 6 IEC 60079-0 Electrical Apparatus for explosive gas atmosphere-Part 0: General Requirements; IEC 60079-1 Electrical Apparatus for explosive gas atmosphere-Part 1: Flameproof enclosures “d”; IEC 60079-7 Electrical Apparatus for explosive gas atmosphere-Part 7: Increased Safety “e”; IEC 60079-10 Electrical Apparatus for explosive gas atmosphere-Part 10: Classification of hazardous areas;