Maxtrac 9917MR GM Truck Front and Rear Lowering Magneride

Total Page：16

File Type：pdf, Size：1020Kb

Maxtrac 9917MR GM Truck Front and Rear Lowering Magneride

9917MR 2014 + GM TRUCK FRONT AND REAR LOWERING MAGNERIDE KIT DESIGNED TO FIT OUR 2/4, 3/5 AND 4/6 DROP KITS PARTS LIST: (2) 9915MR front sensor rods (2) 9915MR2 rear sensor rod plates (2) M6-1.0 nylock nuts NOTE: This sensor rod components kit should be installed as the truck is being put back together after installing the lowering kit. NOTE: If you are only installing drop spindles, the rods will not need to be used. STEP 1: Separate the front sensor rod from both mounting points and remove. STEP 2: The plastic rod ends are held onto the sensor rod by a rib engaged into a retaining groove. To separate, tighten the rod into a vise and use a pair of pliers to pry the rod end off. Repeat for both rod ends. STEP STEP 2 2 STEP 2 STEP 3: If installing 1” drop coils, you will pop the rod ends onto the new rod as is and install it back onto the truck. IF NOT, PROCCED TO STEP 4. STEP 4: If you are installing 2” drop 2” DROP- coils, then you will need to cut off the CUT HERE end of the new rod, right where the first groove ends, then install the rod ends and install back onto the truck. STEP STEP 4 4 STEP 5: The rear sensor plate will need to be installed as soon as the axle is flipped and the U-bolts are ready to be installed. Remove the mounting ball from the original plate and re-attach it to the new plate using the provided 6mm nut. STEP STEP 5 5 NOTE: If installing a 4” or 6” drop, the ball will be installed in the fur- thest hole. NOTE: If installing a 5” drop, the ball will be installed in the closer hole. STEP 5 STEP STEP 5 5 4 inch drop STEP 6: Now place the new plate in-between the leaf spring and the axle relocator. NOTE: If installing a 4” flip kit, the new sensor plate will orient towards the front of the axle and upward. STEP 6 5 inch drop NOTE: If installing a 5” or 6” flip kit, the sensor plate will need to orient towards the front of the axle and downward. STEP 6 6 inch drop STEP 6 STEP 7: Once the plate is installed and the U-bolts are tight, attach the rod to the ball joint..

Copy Link

Recommended publications

Instructions for M-Xxxx-Xxxx
M-9602-M Spring and Stabilizer Bar Kit w/ MagneRide Calibration NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS Please visit www. performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS, PLEASE CALL THE FORD PERFORMANCE TECHLINE AT 1-800-367-3788 M-9602-M is designed for 2018+ Mustangs equipped with MagneRide and includes a unique MagneRide calibration that is loaded with the included Procal voucher and software. Please reference the instruction tab on the Procal and make sure you use version 3.9+ Kit Includes: Front Stabilizer Bar Front Springs Rear Stabilizer Bar Rear Springs MagneRide Tuning Calibration Front Stabilizer Bar Removal NOTICE: Suspension fasteners are critical parts that affect the performance of vital components and systems. Failure of these fasteners may result in major service expense. Use the same or equivalent parts if replacement is necessary. Do not use a replacement part of lesser quality or substitute design. Tighten fasteners as specified. 1. Remove all 4 wheels and tires and set aside. 2. On both sides. 1. NOTE: The stabilizer bar links are designed with low friction ball joints that have a low breakaway torque. NOTE: Use the hex-holding feature to prevent the ball stud from turning while removing the stabilizer bar link nut. Remove and the front stabilizer bar link lower nut. 2. Position aside the front stabilizer bar link. Factory Ford shop manuals are available from Helm Publications, 1-800-782-4356 Techline 1-800-367-3788 Page 1 of 41 IS-1850-0631 M-9602-M Spring and Stabilizer Bar Kit w/ MagneRide Calibration NO PART OF THIS DOCUMENT MAY BE REPRODUCED WITHOUT PRIOR AGREEMENT AND WRITTEN PERMISSION OF FORD PERFORMANCE PARTS 4.
[Show full text]
You Auto Know New for 2018
You Auto Know 2018 Mustang Key Mustang Messages Mustang is designed to appeal to current enthusiasts as well as a new generation of drivers. Impressive features include its sleek design, advanced technology and performance, with two powerful engines and features like MagneRide Damping System Two engines, including the 5.0L Ti-VCT V8 and a 2.3L EcoBoost An all-new 10-speed automatic transmission Available Active Valve Performance Exhaust provides throaty Mustang sound or more aggressive rumble with the ﬂip of a switch Available 12-inch LCD digital instrument cluster for customizable performance Impressive array of standard and available advanced technology features, including: ‒ SYNC Connect powered by FordPass and Wi-Fi® hotspot ‒ Light-emitting diode (LED) headlamps and foglamps ‒ Pre-collision Assist with Pedestrian Detection Several packages allow owners to add unique style to their Mustang Key Mustang Features 5.0L Ti-VCT V8 and 2.3L EcoBoost engines Active Valve Performace Exhaust 12" LCD digital instrument cluster Selectable drive modes MagneRide Damping System Launch control Innovative driver-assist technologies GT and EcoBoost Performance Packages NOTE: For product features, please see Models & Packages and/or the Dealer Ordering Guide for availability. New for 2018 New for 2018 2018 Mustang Features Performance/Handling Revised 2.3L EcoBoost and more powerful 5.0L Ti-VCT V8 All-new dual fuel delivery system, combines port fuel and direct injection to the 5.0 Ti-VCT V8 All-new 10-speed SelectShift automatic transmission Active
[Show full text]
Steeda S550 Mustang Magneride Dual Rate Ultimate Handling
Steeda S550 Mustang MagneRide Dual Rate Ultimate Handling Lowering Springs Instructions for 555-8243 • A qualified technician should be used if you are not confident with removing and installing the vehicles front struts & springs. • A suspension coil spring compressor must be used to allow for replacement of the mount and/or coil spring. • Caution: Coil springs store a tremendous amount of energy. 1 Failure to properly remove and install the springs can lead to severe injury. • The vehicle will require an alignment following installation. • Refer to a service manual for fastener torque specifications and make sure to torque suspension components at curb. Front Spring Installation 1. Lift the car, by the chassis, on a vehicle lift or with a jack, and supported by jack stands, to work on the front suspension of the car. 2 2. Remove the front wheels. 3. Remove the ABS harness from the strut. 4. Disconnect the sway bar end link from the strut. 5. Remove the four bolts securing the brake caliper to the spindle and the spindle to the strut. See image 2. 6. Disconnect the MagneRide plug on the bottom of the strut. Remove 7. From under the hood, remove the 3 nuts securing the strut to the strut tower. The strut can now be removed. 8. Using a coil spring compressor, compress the front spring until there is no tension on the upper strut mount. Once the spring is safely secured, remove the nut holding down the upper strut mount. Then, separate the strut from the spring and the upper strut mount.
[Show full text]
2016 GM 1500 Denali Pickup W/ Magneride & Stamped Steel Lower Control Arms 2.5”
921131500 2016 GM 1500 Denali Pickup w/ Magneride & Stamped Steel Lower Control Arms 2.5” Kit Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions, professional knowledge of disassemble/reassembly procedures as well as post installation checks must be known. Attempts to install this system without this knowledge and expertise may jeopardize the integrity and/or operating safety of the vehicle. Please read instructions before beginning installation. Check the kit hardware against the parts list on this page. Be sure you have all needed parts and know where they go. Also please review tools needed list and make sure you have needed tools. PRODUCT USE INFORMATION As a general rule, the taller a vehicle is, the easier it will roll. Seat belts and shoulder harnesses should be worn at all times. Avoid situations where a side rollover may occur. Generally, braking performance and capability are decreased when larger/heavier tires and wheels are used. Take this into consideration while driving. Do not add, alter, or fabricate any factory or after-market parts to increase vehicle height over the intended height of the Rough Country product purchased. Mixing component brands is not recommended. Rough Country makes no claims regarding lifting devices and excludes any and all implied claims. We will not be re- sponsible for any product that is altered. This suspension system was developed using a 285/70/17, tire with factory wheels. Note if wider tires are used, offset wheels will be required and trimming will be required.
[Show full text]
Steeda S550 Mustang Magneride Lowering Springs
Steeda S550 Mustang MagneRide Lowering Springs Instructions for 555-8242 • A qualified technician should be used if you are not confident with removing and installing the vehicles front struts & springs. • A suspension coil spring compressor must be used to allow for replacement of the mount and/or coil spring. • Caution: Coil springs store a tremendous amount of energy. 1 Failure to properly remove and install the springs can lead to severe injury. • The vehicle will require an alignment following installation. • Refer to a service manual for fastener torque specifications and make sure to torque suspension components at curb. Front Spring Installation 1. Lift the car, by the chassis, on a vehicle lift or with a jack, and supported by jack stands, to work on the front suspension of the car. 2 2. Remove the front wheels. 3. Remove the ABS harness from the strut. 4. Disconnect the sway bar end link from the strut. 5. Remove the four bolts securing the brake caliper to the spindle and the spindle to the strut. See image 2. 6. Disconnect the MagneRide plug on the bottom of the strut. Remove 7. From under the hood, remove the 3 nuts securing the strut to the strut tower. The strut can now be removed. 8. Using a coil spring compressor, compress the front spring until there is no tension on the upper strut mount. Once the spring is safely secured, remove the nut holding down the upper strut mount. Then, separate the strut from the spring and the upper strut mount. Carefully release the stock spring, and compress 3 the new Steeda front spring.
[Show full text]
IHS Automotive Sectoral Report Supplierbusiness the Advanced Chassis Systems Report
IHS Automotive Sectoral Report SupplierBusiness The Advanced Chassis Systems Report 2013 edition supplierbusiness.com IHS Automotive SupplierBusiness | The Advanced Chassis Systems Report Contents Introduction ..................................................................................................................................................................... 6 Electrification within the chassis .............................................................................................................................. 7 Chassis performance .................................................................................................................................................. 9 Design compromise ..................................................................................................................................................... 9 Manufacturing economics ........................................................................................................................................ 10 Platform development and component commonality ........................................................................................... 11 Noise vibration harshness ........................................................................................................................................ 13 Key Development drivers ............................................................................................................................................. 14 Greenhouse gas emissions and fuel efficiency
[Show full text]
The Automotive Suspension Systems Report Supplierbusiness
SupplierBusiness The Automotive Suspension Systems Report 2013 Edition The Automotive Suspension Systems Report CONTENTS Introduction ................................................................................................................ 7 Key market drivers .................................................................................................... 12 Fuel efficiency and CO2 emissions .......................................................................... 12 The United States ................................................................................................ 12 The European Union ........................................................................................... 13 Japan .................................................................................................................. 14 China .................................................................................................................. 14 Other countries .................................................................................................... 15 Materials considerations ......................................................................................... 15 Increasing electrification ......................................................................................... 20 Systems integration.............................................................................................. 20 Challenges and barriers ........................................................................................... 24 Chassis
[Show full text]
Magneride Performance and Challenges
MagneRide Performance and Challenges Vehicle Dynamics Expo 2008 06 May 2008 1 Delphi MagneRide System MagneRide Advantages • Wide range between minimum and maximum forces • High authority at low piston velocities • Fast and linear response to control input • No moving parts Yaw Body Control Stability and Handling Control – Reduces body motions – Improves vehicle stability, steering response, and directional control – Improves impact isolation – Controls transient pitch/roll motions – Improves ride quality and comfort – Improves handling Pitch Roll Wheel Control Adaptive Controls – Reduces wheel shake/resonance during – Driver Mode switch and after impacts Heave – Load compensation – Reduces tire normal load variation and improves road holding – Vehicle speed dependence – Improves feeling of safety – Special events management – Provide vehicle refinement Delphi is a leader in Controlled Damping Systems Technology 2 MagneRide Piston Principle of Operation F High Pressure Magnetic Field Low Pressure MR FLUID 3 Vehicle Performance Vehicle test and configuration Vehicle: • Type: Large European Luxury Car • Mass: 2100 kg (distribution of 57% / 43%) • Tyres: Bridgestone 255/45 ZR 18 Semi-active suspension systems compared: • Reference car : Production Semi-Active Suspension with levelling (Ref) • Delphi car : MagneRide system with levelling (MR) => Suspension modes : Two, Soft and Hard for each vehicle Vehicle Handling Tests: VDA ISO 7401 Acceleration to 90km/ Sweep ISO7401 Step steer ISO 7401 on referenced bumpy road Freq: 0. to 2.5 Hz 80kph,
[Show full text]
Application Guide Overload Springs? for Your Vehicle
POPULAR APPLICATIONS RideCONTROL™ LoadLifter LoadLifter Air Lift LoadLifter LoadLifter Air Lift ™ ™ ™ Year Model AIR LIFT 1000 5000 5000 ™ ProSeries 5000™ 7500 XL ProSeries TABLE OF CONTENTS AIR LIFT 1000HD™ Ultimate Ultimate Plus Ultimate CHEVROLET/GMC 2019-2021 Silverado/Sierra 1500 2WD & 4WD - Call for 2022 57288 88288 89288 93288 94288 2019-2021 Silverado/Sierra 1500 Trail Boss/AT4 4WD 57388 88388 89388 93388 94388 Popular Applications ............................................................ 3 2019 Silverado 1500 Legacy/Sierra 1500 Limited 57204 88204 89204 93204 94204 Silverado/Sierra 1500 2WD & 4WD 2007-2018 59565 57204 88204 89204 Why Air Springs? ............................................................... 4 Short & Standard Bed 2007-2018 Silverado/Sierra 1500 2WD & 4WD Long Bed 57211 88211 Why Air Lift? .................................................................. 5 2011-2019 Silverado/Sierra 2500HD & 3500HD 57338 88338 89338 57538 93338 94338 2020-2022 Silverado/Sierra 2500HD 57341 88341 89341 57541 93341 94341 2020-2021 Silverado/Sierra 3500HD - Call for 2022 57341 88341 89341 57541 93341 94341 Product Overview .............................................................. 6 2007-2022 GMC Acadia 60816 2007-2017 Buick Enclave 60816 Adjustable Load Support Applications: 2008-2017 Chevy Traverse 60816 LoadLifter 7500 XL, LoadLifter 5000 Ultimate Plus, LoadLifter 5000 Ultimate, LoadLifter 5000, 2000-2020 GMC Yukon & Yukon XL 1500 60769 RideControl, Air Lift 1000, Air Lift 1000 HD, ProSeries, ProSeries Ultimate ................... 8 2000-2020 Chevy Tahoe 4 Door Only/Suburban 1500 60769 1996-2021 Chevy Express G-2500 Heavy Duty - Call for 2022 57205 88205 1996-2021 Chevy Express G-3500 Passenger Van Only 57205 88205 SlamAir Applications Load support for lowered vehicles ......................................... 34 1996-2021 GMC Savana G-2500 & G-3500 - Call for 2022 57205 88205 2015-2021 Chevy Colorado/GMC Canyon 2WD & 4WD - Call for 2022 59533 Drag Bags Applications Air suspension for drag racing ........................................
[Show full text]
2015 Gmc Sierra 1500 Denali Vin: 3Gtu2wec2fg287055
13811 Poway Rd PEDDER CDJR Poway, CA, 92064 Stock: C18493A 2015 GMC SIERRA 1500 DENALI VIN: 3GTU2WEC2FG287055 Current Sale Price: $38,462 Your savings: $10,423 Iridium Metallic 56,756 miles 56,756 miles MPG: 16 City - 22 Hwy 6-Speed Automatic Electronic… 4x4 8 cylinders VEHICLE DETAILS Automatic 2WD 4X4 Transmission Heated Front Seat Navigation Brake Assist Keyless Entry 09/29/2021 14:12 https://www.powaycdjr.com/inventory/used-2015-GMC-Sierra+1500-Denali-3GTU2WEC2FG287055 Mon - Fri: 9:00am - 9:00pm 13811 Poway Rd Sat: 9:00am - 9:00pm Poway, CA, 92064 858-883-2700 Sun: 9:00am - 8:00pm 13811 Poway Rd PEDDER CDJR Poway, CA, 92064 Stock: C18493A 2015 GMC SIERRA 1500 DENALI VIN: 3GTU2WEC2FG287055 EXTERIOR Front Center Armrest w/Storage OnStar 6 Months Directions & Connections Plan Passenger door bin OnStar w/4G LTE Exterior Parking Camera Rear Power Adjustable Pedals Delay-off headlights Rear Vision Camera w/Dynamic Guide Lines MECHANICAL Front fog lights Ultrasonic Front & Rear Park Assist Fully automatic headlights Speed-sensing steering Perforated Leather Appointed Seat Trim Auto-dimming door mirrors 4-Wheel Disc Brakes Rear 60/40 Folding Bench Seat (Folds Up) Bodyside moldings Front anti-roll bar Front Frame-Mounted Black Recovery Hooks Bumpers: body-color Front wheel independent suspension Chrome wheels Heated door mirrors Electronic Stability Control Wheels: 20" x 9" Ultra Bright Machined Aluminum Power door mirrors Deep-Tinted Glass Rear step bumper SAFETY 3.42 Rear Axle Ratio Turn signal indicator mirrors LOW MILES
[Show full text]
Development of a Semi-Active Suspension System for Lightweight Automobiles
Development of a Semi-active Suspension System for Lightweight Automobiles Sheetanshu Tyagi Thesis submitted to the faculty of the Virginia Polytechnic Institute and State University in partial fulfillment of the requirements for the degree of Master of Science In Mechanical Engineering Saied Taheri (Chair) Mehdi Ahmadian Corina Sandu June 17th, 2016 Blacksburg, VA Keywords: semi-active, damper, testing, design, suspension Copyright 2016, Sheetanshu Tyagi Development of a Semi-active Suspension System for Lightweight Automobiles Sheetanshu Tyagi ABSTRACT Vehicle suspension systems play an integral role in influencing the overall performance of a vehicle. The suspension system of a vehicle performs multiple tasks, such as maintaining contact between the tires and the road and isolating the frame of the vehicle from road-induced vibration and shocks. A significant amount of research has been directed to improving the performance of the suspension system by varying the damping coefficient so as to alter the frequency response of the system. This study describes the development of such a damper. The goal of this research has been to design, model, fabricate and test a novel semi-active damper. The damper consists of two independent electronically controlled units placed in series with one another. The system was initially simulated using a 2 DOF quarter-car model and the performance characteristics of the damper were outlined. Following that, multiple design iterations of the damper were created and a MATLAB/Simulink model was used to simulate physical and flow characteristics of the damper. After the design and analysis was complete, the damper was fabricated and tested using a shock dyno at CenTiRe.
[Show full text]
Suspension Systems
SuperSprings® SuperSprings® are a unique and patented self-adjusting suspension stabilizing system for vehicles with rear leaf springs, designed to level loads and reduce body roll. SuperSprings® provide users extra load support and reduce body roll without compromising ride quality. They are manufactured using a variety of different sized springs to CHEVY/GMC SuperSprings support multiple applications. All SuperSprings® are manufactured in the 14-20 Silverado/Sierra 1500 (19 Old Body) SSPSSA28 U.S.A. from SAE5160H 99-13 Silverado/Sierra 1500 SSPSSA8 high grade, shot 11-20 Silverado/Sierra 2500/3500 (3400# Capacity) SSPSSA13 peened steel. 11-20 Silverado/Sierra 2500/3500 (1800# Capacity) SSPSSA16 01-10 Silverado/Sierra 2500/3500 SSPSSA15 01-20 Silverado/Sierra 3500 (2300# Capacity) SSPSSA23 91-00 Silverado/Sierra 3500 SSPSSA22 96-19 Express/Savana SSPSSA14 DODGE/RAM SuperSprings ▪ Sold as a pair (left and right) 03-13 Ram 2500/3500 SSPSSA15 ▪ Maintenance-free 03-07 Ram 25000/3500 (3500 03-19) SSPSSA23 ▪ Self-adjusting suspension 94-02 Ram 2500/3500 SSPSSA22 stabilizing system FORD SuperSprings ▪ 1500 (lb) Additional 04-20 F-150 SSPSSA28 Load-Leveling Ability 08-10 F-250/F-350 Super Duty SSPSSA15 ▪ Reduces body roll up to 30% without compromising ride quality 11-16 F-250/F-350 Super Duty SSPSSA16 ▪ Works in conjunction with original equipment leaf spring assembly 80-20 F-250/F-350 Super Duty SSPSSA22 ▪ Adjustable shackles allow installation to suit various needs ▪ Typical installation completed in approximately one hour 08-10 F-350 SSPSSA23
[Show full text]