Custom Rolling, Bending, Forming Steel - Since 1984 Toll Free: 877-754-0900 Plate Bending, Sheet Metal Bending Press Brake Plate Bending - Sheet Metal Bending www.jorgensonrolling.com
Big bent plates on palette Formed Channels on forklift
Plate Bending Plate Bending
Aluminum Brackets Bent and Punched Thick Bent Plate 500 tons Press Brake
Plate Bending and Punching Plate Bending
This is 3/8” aluminum flat bar that has been bent in three places This is 5/8” thick plate that has been bent to 90 degrees at and punched at each end to be used as a bracket. These brackets multiple points. At Jorgenson Metal Rolling and Forming we were bent using our 500 ton 18 foot press brake, which allows us specialize in bending plate and rolling plate, we also do angle to bend steel plate up to ½” thick by 10 feet long, and 3/8” thick rolling, tube rolling and pipe rolling. We also have a Custom plate up to 18 feet long. Bending and Forming is our specialty Metal Fabrication department located in our facility, where we here at Jorgenson Metal Rolling and Forming. We also specialize do shearing, punching and welding. in structural steel rolling using most shapes such as beam rolling, angle rolling, pipe rolling and tube rolling.
1 Custom Rolling, Bending, Forming Steel - Since 1984 Toll Free: 877-754-0900 Plate Bending, Sheet Metal Bending Press Brake Plate Bending - Sheet Metal Bending www.jorgensonrolling.com
Bent and Punched Steel Brackets Bent Plate
Plate Bending Plate Bending This is 3/4” thick plate that has been bent to 90 degrees. This This is 3/8” thick plate that is 10 feet long and has been bent to plate was also sheared to size and punched. Plate shearing and 90 degrees. At Jorgenson Metal Rolling and Forming bending punching are a part of our full service custom metal fabrication plate as well as rolling plate is just one of our many capabilities; department, which is located in the facility. At Jorgenson Metal our shop also has the ability to do plate rolling up to 1.0” thick Rolling and Forming we can do heavy duty plate bending as well and up to 10 feet in width. We also specialize in angle rolling, as rolling, our shop also has the ability to do plate rolling up to channel rolling, beam rolling and pipe rolling. 1.0” thick and up to 10 feet in width.
Bent Steel Plate Formed Shapes Press Brake Bent Steel Plates
Plate Bending Plate Bending This is 1/2” thick plate bent at multiple points, to various de- This is 5/8” thick plate that has been bent to 90 degrees at two grees. At Jorgenson Metal Rolling and Forming bending plate, points to form a saddle. This plate was also punched in our cus- as well as plate rolling, are just two of our many capabilities, we tom metal fabrication department, which is located in our facil- can also do sheet metal bending, tube bending and pipe bending. ity. At Jorgenson Metal Rolling and Forming we can do heavy We also have a Custom Metal Fabrication department located duty plate bending as well as rolling, our shop also has the ability in our facility with capabilities such as shearing, punching and to do plate rolling up to 1.0” thick and up to 10 feet in width. welding.
2 Toll Free: 877-754-0900 Custom Rolling, Bending, Forming Steel - Since 1984 Toll Free: 877-754-0900 Plate Bending, Sheet Metal Bending Press Brake Plate Bending - Sheet Metal Bending www.jorgensonrolling.com
Formed Stainless Steel Plate Bent
Plate Bending This is 1/4” thick plate bent to various degrees. This plate was also sheared to size in our custom metal fabrication department, which is located in our facility. At Jorgenson Metal Rolling and Forming bending plate as well as rolling plate is just one of our many capabilities, we can also do sheet metal bending, tube bending and pipe bending.
3