DOCSLIB.ORG

Centurion Low Pitch Tile & Window

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Centurion Low Pitch Tile & Window Centurion Low Pitch Tile & Window Key Limitations for use between 10˚ - 12.4˚ • Rafter length must not exceed 5 metres. • The roof should be located in a sheltered locations only - Not Coastal. • The roof should be single storey only. • The roof should have no penetrations or obstructions through the tile array. • Centurion vent tiles should not be installed below 20º. • Gutter pipes from higher level roofs should not discharge onto the lower Centurion roof. • Centurion tiles should all be clipped. • The Centurion Low Pitch Eave Pack must be used. For full list of clauses please refer to the Centurion literature. If any of the above clauses cannot be followed, Forticrete cannot guarantee the performance of Centurion as the primary weather covering. It may be possible to install a primary weather covering underneath the tiles. This means that the tiles would be for purely decorative purposes. One under tile system available is Ondutile, refer customer to Ondutile as a suggestion. Low Pitch Roof Window • The Low Pitch Roof Window System can be used down to pitches of 10˚. • Additional support rafters will be needed - Refer to example roof layout. • Underlay and battens cannot be installed until the Low Pitch Roof Window system has been received. This is because the trays must be installed underneath the battens. • If the window is ordered separately to the tiles the customer will not receive tile clips and verge clips unless they have been ordered separately. Window Specifications Window Size 550mm x 980mm One Size Only! Glazing Size 370mm x 825mm Window U-Value 1.4 W/m2K Glazing U-Value 1.1 W/m2K RW Coefficient 32 dB Finishes Available White / Pine Low Pitch System Contents LPS Box Tray Pack Eaves Pack (3m) Centurion Abutment (Pack D) (Pack C) (Pack B) Pack (3m) (Grey or Rustic) BUZ/7953/LRSD/-- BUZ/7953/LRSC/00 BUZ/7953/LRSB/00 BUZ/7951/CSA3/-- • Roof Window • Bottom Tray • Underlay Support Tray • Centurion Top Fillers • Flashings • Top Tray • Eaves Batten Blocks • Felt Spacers • Pitching Kerb • Sealing Tape (2m) • Eaves Filler Clips • Top Filler Clips • Brackets + Fixings • Foam Support Blocks • Eaves Filler Clip Screws 45mm • 45mm Screws + Washers • Eaves Filler Clip Screws 80mm • Tile Adhesive • Eaves Batten November 2019 Centurion Low Pitch Tile & Window Frequently asked questions Low pitch roofs and roof windows What is the minimum spacing between two Minimum 1800mm between window centres, battens must have 3 fixings into rafters windows? between trays. Can I use your trays with another window? No, the flashings have been specifically designed to fit with the Forticrete tray. No, the complete system is supplied by Forticete. The system can be ordered Can I buy the window through another supplier? through Centurion Tile stockists, for more information please contact our customer service department. Yes. Forticrete are unable to guarantee the system without the installation of Can I order the system without Centurion tiles? Centurion tiles. Do you offer other window sizes? Not at the moment, we may look to expand the range in the future. Can I use the Low Pitch Roof System with Yes. Forticrete are unable to guarantee the system without the installation of another suppliers tiles? Centurion tiles. You will need to provide your own eaves detail. Can I fit another suppliers window with Centurion? The minimum pitch for another suppliers window (i.e. Velux) with Centurion is 15º. Yes but it is impractical and will involve stripping off the all of the tiles and battens Can I retro fit the Low Pitch Window? and installing extra rafters. Do you stock them at Stretton? No. Can I collect? The roof window system can be collection from Leighton Buzzard only. November 2019.
Load more

Recommended publications
  • Installers' Handbook Preface
    HANDBOEK VOOR INSTALLATEURS Handboek voor de installatie van VELUX dakvensters Installers' handbook Preface The purpose of this handbook is to provide an overview of the installation of VELUX products. The handbook describes the various aspects of roof construction in association with VELUX roof windows and also provides advice and information on how to obtain the optimal installation. (Third edition, 2010) The VELUX system Chapter 1 2 3 4 5 6 7 8 Other products Chapter 9 Contents Planning Considerations before choosing roof window 5-13 1 Installation of a roof window Installation step by step 15-25 2 Integration – more windows Combination of more than one window 27-45 3 Special installation conditions Installation in various roof constructions 47-63 4 Special roofing materials Installation in various roof materials 65-81 5 Replacement / renovation Replacement of a roof window 83-93 6 Building physics Roof constructions (humidity, heat, sound etc) 95-109 7 Product information Short presentation of VELUX products 111-137 8 Other products Sun tunnel / Flat roof window / Solar hot water system 139-145 9 Contact VELUX Addresses / Advising / Service 146-147 List of telephone numbers 148 Size chart 151 Planning 1 The construction of the house 6-7 User requirements 8 Building regulations 9-13 VELUX 5 Planning 1 The construction of the house To be able to choose the right VELUX roof window for a given situ- ation, it is always recommended to start from the construction of the house, user requirements and current building regulations. Normally, a standard VELUX roof window can satisfy the basic requirements, but often choosing another window type or vari- ant and/or choosing accessories can optimise the function and increase the utility value of the window.
    [Show full text]
  • Katalog Produktow GB 2008.Indb
    ROOF WINDOWS INTRODUCTION Consultation with the architect helps make decision 8 www.fakro.com Loft Conversion-planning Building or renovation of a house is an investment which requires not only financial expenditure, but also considered decisions and solutions. Each matter should be discussed with professionals who will ad- vise the best way of solving problems. When deciding how and where to place roof windows you should consult an architect, who will help you to choose the right window type depending on the proposed use of the loft. He will also give you advice concerning the window’s glass surface area decided by the ratio to the total floor area and also where to place the win- dows to gain the maximum benefit. Nowadays roof windows are often an indispensable element of newly built structures. They create new, unique, individual possibilities. When adapting or con- The attic before conversion verting the loft and also installing roof windows your loft can be easily changed into a functional, stylish and elegant space. Depending on the client’s individ- ual requirements and the ingenuity of the architects, even the most exceptional ideas can be prepared in the form of computerised 3D visualisation of the project which helps your dreams come true. A completed conversion with two roof windows A completed conversion with four roof windows and blinds ROOF WINDOW 9 ROOF WINDOWS VERSUS DORMER When planning to develop the loft there are two options to get light in: building a dormer (until recently a very popular solution) or installing (becoming more and more popular ) modern roof windows.
    [Show full text]
  • Roof Window Size Comparison
    Roof Windows Roof Window Size Comparison keyliteroofwindows.com Comparison Chart Futuretherm Technology Height (mm) Width (mm) 550 660 780 940 1140 1340 01 03A 04A 07A 08A 09A Keylite CK02 N/A N/A N/A N/A N/A Velux 780 01 22 23 24 25 26 Fakro 02 03B 04 07B 08B 09 Keylite CK04 FK04 MK04 PK04 N/A UK04 Velux 980 02 03 05 15 N/A 12 Fakro 01C 03 05 07C 08 09C Keylite CK06 FK06 MK06 PK06 SK06 N/A Velux 1180 16 04 06 08 10 N/A Fakro 01F 03F 06 07F 08F 10 Keylite N/A FK08 MK08 PK08 SK08 UK08 Velux 1400 N/A N/A 07 09 11 N/A Fakro Keylite 1600 01G 03G 04G 07G 08G 09G Velux N/A N/A MK10 PK10 SK10 UK10 Fakro N/A N/A 13 N/A N/A N/A Centre Pivot Roof Windows Pine White Conservation Pine Conservation White Keylite CP WF-CP CW-CP CW-WF-CP Velux GGL GGU GGL SD5 GGU SD5 Fakro FTP-V FTU-V & PTP-V FTP-V/C PTP-V/C Top Hung / Fire Escape Pine White Conservation Pine Conservation White Keylite FE WF-FE CW-FE CW-WF-FE Velux GPL GPU GPL SD5 GPU SD5 FPP-V & FPU-V & FPP-V/C & FPU-V/C & Fakro FHP-V FHU-V FHP-V/C FHU-V/C Single Flashings Slate Tile Deep Plain Tile Conservation Conservation Conservation Conservation Corrugated Tile Slate Tile Plain Tie Deep Tile Keylite SRF TRF DTRF PTRF CWSRF CWTRF CWPTRF CWDTRF CRF (Recessed As Standard) Standard Recessed Standard Recessed Standard Recessed Standard Recessed Standard Recessed Standard Recessed Standard Recessed Standard Recessed Velux EDL/ EDN EDZ N/A EDW/ EDJ EDP/ N/A N/A EDN N/A N/A EDP N/A EDW EDJ ZWC EBL/ EBW/ EBP/ EKL EKW EKP Fakro EL N/A EZ N/A EH N/A EP N/A /C N/A /C N/A /C N/A /C N/A EE Combi Flashings 18mm
    [Show full text]
  • Tilcor-Installation-Manual-16-EN.Pdf
    INSTALLATION MANUAL BOND / CLASSIC / TUDOR / SHAKE / ROYAL / ANTICA These installation details are provided to demonstrate the recommended installation methods for Tilcor products and accessories. The details and information in this document reflect current roofing practices used in New Zealand. Consult with Tilcor Roofing Systems for additional information. Ross Roof Group Ltd +64 9 299 9498 faks +64 9 298 4114 1c Inlet Road, Takanini 2112, PO Box 72062, Papakura 2244, e-mail: [email protected] web: www.tilcor.com New Zealand 1. General Information ................................................................................. 3 2. Recommended Tools ............................................................................... 9 3. Profile and Flashing Specifications .......................................................... 10 4. Preparation of The Roof Surface for Installation ................................... 14 5. Tile (BOND, CLASSIC, TUDOR, ANTICA) Installation ............................... 16 6. Tile Installation (SHAKE, ROYAL) .............................................................. 19 7. Eaves Flashing ........................................................................................... 20 8. Box Barge Installation (Bond, Classic, Tudor, Shake, Royal) ................. 21 9. Installation of Barrels at The Ridge and Hip ............................................ 22 10. Roof Window Installation ........................................................................ 23 11. Roof Ventilation, Extractor and Sanitary
    [Show full text]
  • Influence of Roof Windows Area Changes on the Classroom
    sustainability Article Influence of Roof Windows Area Changes on the Classroom Indoor Climate in the Attic Space: A Case Study Erika Dolnikova * , Dusan Katunsky , Marian Vertal and Marek Zozulak Institute of Architectural Engineering, Faculty of Civil Engineering, Technical University of Kosice, 042 00 Kosice, Slovakia; [email protected] (D.K.); [email protected] (M.V.); [email protected] (M.Z.) * Correspondence: [email protected]; Tel.: +421-055-602-4162 Received: 28 April 2020; Accepted: 17 June 2020; Published: 20 June 2020 Abstract: Windows are a complex part of building design and provide a considerable benefit, including to school buildings. For the evaluation of the daylighting conditions prevailing in classrooms, the daylight factor (DF) was considered as the most appropriate parameter for indicating the quantity of admitted daylight. The DF values and CIE overcast sky were calculated using Velux Daylight Visualizer 3 software. The task of the paper is to compare various roof window openings in relation to the level of daylight in the attic, looking to optimize the use of the attic for teaching. The indoor air temperature has a general influence on comfort in the interior, in addition to daylight. In winter, the situation is not critical. The thermal insulation properties of packaging structures are sufficient. The situation is worse in summer, due to the fact that the heat-storage properties are undersized and there is excessive overheating of the indoor air. Four variants of roof windows and their influence on the overall microclimate in the attic are compared. The variant without roof windows is a suitable solution with regard to minimum overheating, but the worst situation for daylight.
    [Show full text]
  • Velux Catalog, Residential Products, Dist. by Best Materials®
    Distributed by: BEST MATERIALS ® Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014 www.BestMaterials.com Email: [email protected] Residential skylights Contents The VELUX House Why VELUX skylights The possibilities are endless Information 1 The VELUX House Roof windows are perfect for upper floor bonus rooms where 3 The logical choice for any skylight they will be within reach for installation easy opening. Features include 5 Choosing the right glass a sash that rotates inward for easy cleaning from the inside and a ventilation flap that allows for fresh air circulation when the window is closed. Products Pages 33-40 7 Solar Powered “Fresh Air” Skylights 11 Electric “Fresh Air” skylights Eligible for a 15 Manual “Fresh Air” skylights 19 Fixed skylights 30% Federal tax credit 25 Self-flashed skylights Receive an average of 29 Special order blinds $850* on product and installation with federal 33 Roof windows tax credit eligibility 41 Three layers of protection warranty The Solar Powered “Fresh Air” Skylight features a 43 Deck mounted flashing systems solar panel that charges an 44 Curb mounted flashing systems internal battery and control system. The skylight is remote 45 Skylight accessories controlled and solar powered, 47 SUN TUNNEL™ skylights which means it requires no additional wiring, making 53 SUN TUNNEL™ skylight accessories for easy and cost effective 55 Modular Skylights installation. An integrated 59 NEW Instant light shaft rain sensor closes the unit in case of rain and it is a No Leak Skylight, with our 3 layers of water protection, covered by our 10-year installation Testing data warranty.
    [Show full text]
  • Ekl + Fs, Vs, Vse, Ggl
    EKL + FS, VS, VSE, GGU, GPU, GXU ENGLISH: EKL Deck Mounted Skylight and Roof Window Flashing Installation Instructions ESPAÑOL: Instrucciones de instalación de tapajuntas EKL para tragaluz y ventana de tejado montados sobre tablero FRANÇAIS : Instructions d'installation du solin EKL pour puits de lumière et fenêtre de toit à cadre intégré montés directement sur la toiture 14°-85°15°-90° VAS 452233-2015-06 ENGLISH: Index ESPAÑOL: Índice FRANÇAIS : Index P. 2 Important installation requirements Pág. 2 Requisitos importantes de insta- P. 2 Spécifications d'installation impor- P. 4-8 Planning lación tantes P. 9-13 Installing underlayment Pág. 4-8 Planificación P. 4-8 Planification P. 13-33 Installing flashing Pág. 9-13 Instalación de la lámina de soporte P. 9-13 Installation de la membrane de toiture P. 34 GPU springs Pág. 13-33 Instalación del tapajuntas P. 13-33 Installation du solin Pág. 34 Resortes de GPU P. 34 Ressorts pour GPU ENGLISH: Important installation requirements ESPAÑOL: Requisitos importantes de instalación FRANÇAIS : Spécifications d'installation impor- Roof pitch and roofing material Inclinación del techo y material de cubierta tantes EKL is designed for roof pitches 14° - 85° EKL está diseñado para techos con inclinación Pente de toit et matériel de toiture (3:12 - 137:12) and for thin roofing materials (max de 14° - 85° (3:12 - 137:12) y para materiales de EKL est conçu pour les pentes de toit de 14° - 85° 5 5 thickness /16" (8 mm)). For roof pitches below 14° cubierta delgados (grosor máximo /16" (8 mm)). Para (3:12 - 137:12) avec matériel de toiture mince (épais- 5 (3:12) and for other roofing materials, please contact techos con inclinación inferior a 14° (3:12) y para seur maximale /16" (8 mm)).
    [Show full text]
  • Technical Data Sheet
    technical data 10 YEAR 3 YEAR WWAARRRRANTY WWAARRRRANTY onon ro ofskylights, windows, on blinds,on blinds accessories, GPL Roof Window flashings and glazing and accessories Pitched Roof GPL technical performance Code Mark is a voluntary certification scheme owned by the Commonwealth of Australia that provides legally binding evidence of compliance to the National Construction Code ® of Australia. One certificate replaces dozens of technical papers. Australia Available in 5 sizes Australia Main features 3008930090 Choice Australian Standards of blinds VELUX Skylights are tested and approved to the appropriate Australian Standards. AS4285 SKYLIGHTS** AS1288 OVERHEAD GLAZING Laminated Laminated inner pane double glazing NCC BOUNDARY SEPARATION†† Grey aluminium as standard Class 1 & Class 10 buildings: exterior cappings Within 900mm of a boundary wall Class 2 to Class 9 buildings: 3 metres from a boundary wall^^ Pre-painted VELUX Roof Windows are deemed non- pine frame combustible by CSIRO and thereby comply and sash with NCC boundary separation requirements. BASIX Selection Guide Timber, Low-E, Double glazed, Argon filled †† CSIRO assessment report available on request. VELUX recommends consultation with relevant authority before work commences. Roof Window assessed in closed position. Dual action: top-hung ^^ Roof Window cannot be closer than 3m unless the boundary is with base handle or adjoining a road or public place. Consult NCC for further details. centre-pivot ** Not for use in cyclonic regions. Not suitable for out-of-reach situations INSTALLATION PITCH* Construction Frame and sash: Nordic Pine timber. Factory VELUX GPL is an openable centre- The sash is frictioned to stay in a pivot lacquered with top coat of white paint (NCS colour: S 0500-N).
    [Show full text]
  • Step by Step Installers Guide
    TOOLS REQUIRED: STEP BY STEP 1. Handsaw/skill-saw 2. Battery Drill INSTALLERS 3. Tin Snips 4. Riveter GUIDE 5. Caulking Gun 6. Drill Bits For Roof Penetrations (no greater than 800mm in width) in accordance with the 7. Marker Pen MRM Code of Practise, Version 2.2/2012 8. Nut Setter MANUFACTURERS OF STEELFORM ROOFING WWW.STEELFORMERS.CO.NZ STAGE ONE We recommend a sub-frame be made out Provide additional support for traffic and flashings of 200mm x 45mm timber to be installed down either side of the opening, no greater than between trusses. This frame should be fixed 150mm from the edge of the sub-frame. to the trusses with 90mm x 3.55mm jolt At the lower edge of the sub-frame, provide additional head nails at no greater than 400 centres framing to allow for the fixing of a 200mm apron. and at 150mm from frame corners. Screws At the top of the roof opening sub-frame provide a of the same gauge and length can be used double purlin or H3 Ply to provide support for traffic in this situation if preferred. and additional fixing. Double purlin should be fitted at no less than 150mm above the sub-frame. 2 STAGE TWO Please note the safety from falling netting which must be used on openings greater than 450mm x 900mm. The roofing underlay is cut and folded up the sub-frame and the underlay is then stapled to the sub-frame pedestal. 3 STAGE THREE STAGE FOUR Flashing tape is then cut to length to cover Cut profile sheets around the sub-frame any visible timber on the sub-frame up- (pedestal) and make sure to turn up the stand as shown, minimum 400mm in length.
    [Show full text]
  • Flashing Systems 06
    ISSUE FLASHING 06 SYSTEMS Selection and Installation Handbook • Longrun Metal Roofs • Concrete, Slate and Tile roofs • Flues • Pipes • Ridges • Apron Flashings • Hip Flashings • Damp Proof Course • Silicone • Tape Email: [email protected] Web: www.dlmwallace.co.nz Auckland Wellington Christchurch Tel 09 622 9100 Tel 04 567 8125 Tel 03 365 6453 DLM Flashing Systems The versatile solution Time and money saving answers for every flashing situation Whatever your building and construction flashing requirements, you will find an innovative, practical answer in the DLM range of flashing systems. The unique features and high performance of any DLM flashing system symbolises the care and attention to design detail that goes into every DLM product. From the smallest cable penetration through to roof, window and door flashings or for an emergency repair in a hurry DLM will provide the ultimate weather tight seal. When you choose from the DLM flashing systems you will discover the advantages of doing it right with better performance and an easier, more cost effective installation. Contents Dektite Design features ................................................................................................................................................. Page 1 Dektite Premium The versatile solution ............................................................................................................. Page 2-3 Dektite Premium Solar Flashing Perfect for flashing pipes and cables on any roof type .................... Page 4 Dektite Shingle
    [Show full text]
  • Glazing Vision Guide to Rooflights and Roof Window
    guide to rooflights & roof windows We all have a predilection to well lit, airy and inviting spaces, so increasing the use of glazing products in the built environment can be an efficient way of improving an internal space. There are a number of products available that offer varying degrees of natural daylight and ventilation in the form of rooflights and roof windows. While most people will be familiar with these products, what are the key differences between them and which one should be specified in a given application? Rooflight or roof window? Roof windows are The simplest way to answer this question is to first consider the roof type that your product is going to be installed; is it a flat roof or a pitched roof? In most cases a rooflight will be installed usually installed on on a flat roof or terrace and fixed to an upstand or kerb with a minimum pitch of around 3-5° a pitched roof of Roof windows are usually installed on a pitched roof of 15° or 15° or more. more; normally these are designed to allow installation up to a maximum 60°, with some products being able to be fixed up to 90°. t. 01379 658300 Sawmills Road, Diss, e. [email protected] Norfolk, IP22 4RG rooflights.com is a division of Glazing Vision ltd, registered in England no. 2987024 Roof window types The most widely used roof windows are centre pivot and top hung units; these products provide reasonable levels of daylight and ventilation and are popular on new builds, having been adopted by most large housing developers.
    [Show full text]
  • 901 Monticello Avenue Parcel ID: 570060000 DHR Resourc
    DHR Resource Number: 104-5082-0164 901 MONTICELLO AVENUE Street Address: 901 Monticello Avenue Parcel ID: 570060000 DHR Resource Number: 104-5082-0164 Primary Resource: Single Dwelling (contributing) Secondary Resource: Garage (contributing) Date: 1946 Style: Minimal Traditional Property Description Site Description: Monticello Avenue (State Route 20) is the main thoroughfare through the Belmont neighborhood. The road winds into the south end of the neighborhood and extends to the west where it intersects with Avon Street. Development in Belmont first occurred north of Monticello Avenue with the southern section of the neighborhood developing in the mid- to late-twentieth century. The road was widened around 1960 (when the new Avon Street bridge was constructed) and today serves as a major tourism and commuter route into Downtown Charlottesville. This property is located at the northeast corner of the intersection of Monticello Avenue and Meridian Street. The front yard is enclosed by a chain link fence and a wooden fence encloses the rear yard. Large trees are planted in the front and back of the property. Primary Resource Description: This one-story, L-shaped dwelling is of concrete block construction with a brick veneer (stretcher bond). The house is covered by a side-facing gable roof of asphalt shingles with a projecting front-facing gable- roofed wing. A stout brick chimney is centrally located on the side-facing roof ridge line. The three-bay front elevation (south) of the side wing holds an entrance with a paneled wooden door and two six-over-six wooden sash windows. A single six-over-six window is present in the end of the projecting gable wing.
    [Show full text]