Owner's Manual Fashion Skirted Toilet with P & S Trap Dual Flush

DUAL FLUSH FASHION SKIRTED TOILET WITH P & S TRAP

ITM. / ART. 161018 OWNER’S MANUAL # QTA021 Table of Contents

Table of Contents ...... 2 Installation ...... 6 Important Information ...... 2 Seat Installation ...... 10 Warranty Troubleshooting ...... 10 One Year Limited Warranty ...... 3 Care and Cleaning ...... 10 Warranty Claim Procedure ...... 3 Service Parts ...... 11 Pre-Installation ENGLISH Package Contents ...... 4 Tools Required ...... 4 Specifications ...... 5

Information

BEFORE BEGINNING INSTALLATION, READ ALL INSTRUCTIONS FIRST . SAVE THESE INSTRUCTIONS FOR FUTURE USE .

If there are any problems with installation or operation, do not return to store. Please first call customer service at +61 2 87245218 (Monday to Friday, 6:30 am to 3 pm AEDT) .

- Observe all local plumbing and building codes. WARNING: Ensure that these installation instructions are left with the end user for future reference . It is - Carefully inspect the new toilet and components for damage . recommended that the toilet seat and cover be installed - If the existing toilet installation area does not have a supply after all trade-work is finished. shut-off valve below the tank, you will need to install one NOTE: before installing the new toilet . Check all measurements against the actual toilet before commencing - Ceramic toilets are very fragile, so please handle your new as variances do occur. toilet with extra care during installation . Once the toilet is removed from the packaging, always ensure that it is placed on a soft surface such as a towel or blanket before installation .

BRAND Westinghouse MODEL NO . QTA021 RECOMMENDED USE Domestic MATERIAL White Vitreous China WEIGHT Pan: 27 kg Cistern: 15 kg FIXING Toilet pan screwed and siliconed to floor / Cistern bolted directly to pan STANDARDS AS 1172.1 & AS 1172.2 CISTERN FIXING Bolt directly to pan using bolts provided. RIM OF PAN Boxed Rim to prevent splashing and direct water nore efficiently TRAP CONFIGURATIONS P Trap (Convert to S trap using approved plastic bend) S trap 80 mm to 210 mm depending on type plastic bend required FEATURES SET OUT P trap 180 mm fixed (height from floor to centre of outlet on pan, allow for 8mm fall to point in wall) SEAT Polypropylene seat, soft close, detachable with chrome hinges WATER INLET Bottom left or bottom right viia removable cap on the pan / WDI inlet WATER RATING Complies with Australian standards at 4.5L full flush and 3L half flush OUTLET VALUE Quality outlet valve for reliability and quiet operation (Easy quick release washer change feature saves time and money)

2 QTA021 Warranty

ONE YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported . We will not be liable for failures or ENGLISH damage that could have been discovered or avoided by proper inspection and testing prior to installation.

Conglom Kitchen & Bath warrants this product to be free from defects in materials or workmanship for one (1) year from the date of purchase . Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to Conglom Kitchen & Bath for all warranty claims .

This warranty is non-transferable and shall be voided if the unit is removed from its initial installation or if it is not installed following the manufacturer’s instructions. It does not apply in the event of product damage due to the use of other than genuine Conglom Kitchen & Bath replacement parts, (Replacement parts may be obtained by e-mail at [email protected] or by calling +61 2 87245218 between 6:30 am - 3:00 pm AEDT) installation error, abuse, misuse or improper care and maintenance (whether performed by a plumber, contractor, service provider or member of the purchaser’s household). The warranty xcludese damage due to aggressive air or water conditions, harsh or abrasive cleaners and/or materials .

Under no circumstance shall we be held liable for personal injury or property damage resulting from improper installation or use of this product. We will not be held liable for inconvenience caused by loss ofse u of this product, costs incurred for labour or materials, removal and installation of replacement units, or any other incidental or consequential damages . Costs relating to obtaining access for repair or replacement are the responsibility of the user .

Our obligation shall be limited to the repair or replacement of a unit (at our discretion) that may prove, by our sole examination, to be defective under normal use and service during the warranty period.

Any failure of this product that is not traceable to a defect in material or workmanship is not covered by this warranty. These non-warrantable items include, but are not limited to:

- Improper installation not in accordance with manufacturer’s instructions . - Dents and/or scratches incurred during shipping, handling, or installation . - Change in colour or finish due to chemical usage. - Damage caused by failure to follow care and cleaning guidelines, including damage caused by the use of abrasive cleaners. - Alterations made to the unit by the purchaser or installer . - Damage caused by accidental impact, fire, flood, freezing, and normal wear. - Bends and warping caused by forced connections, over-tightened fittings, and inadequate support during installation. - Use of any toilet cleaner that are applied in the toilet tank will void the warranty. In-tank cleaners can damage the rubber, metal and/or plastic components, causing leaks and reducing performance . WARRANTY CLAIM PROCEDURE If a claimable defect occurs or replacement parts are needed, please contact our customer service team at [email protected] or +61 2 87245218 (Service available Monday - Friday from 6:30 am - 3 pm AEDT). Before you make your call, please ensure that you have:

- Model number or description . - Proof of purchase . - Details regarding the defect and/or part number . - Name(s) and address(es) of the owner and/or installer .

3 CONGLOMKB .COM Please contact [email protected] or +61 2 87245218 for further assistance . Pre-Installation PACKAGE CONTENTS

C D

ENGLISH A B

H K J

P M

Part Description Quantity Part Description Quantity A Fashion Skirted Toilet 1 H Mounting Bracket Screws 2 B Seat 1 J Toilet Bowl Mounting Screws 2 C Mounting Brackets 2 K Covers 2 D Metal Washers 2 L Hinge Plates 2 E Washers 2 M Bolts and Washer 2 F Caps 2 N Expansion Nuts 2 G Anchors 2 P S Trap Adaptor 1

TOOLS REQUIRED (NOT SUPPLIED)

Adjustable Carpenter’s Safety Water Hacksaw wrench Level Goggles Supply Line

4 QTA021 Pre-Installation SPECIFICATIONS

NOTE: ENGLISH Ensure that the inlet water pressure does not exceed 500kPA as per AS/NZ35003.3.2.

38 cm

16 cm 43 cm

15 cm 83.5 cm

66 cm

42 cm 41.5 cm

18 cm

36.5 cm 20.5 cm

S TRAP INSTALLATION S TRAP INSTALLATION P TRAP INSTALLATION 80-150 MM SET OUT 150-210 MM SET OUT

83.5 cm 83.5 cm 83.5 cm

41.5 cm 41.5 cm 41.5 cm

Ø10 Ø10 Ø10

Fixing hole Fixing hole Fixing hole 32.5 cm 32.5 cm 32.5 cm

5 CONGLOMKB .COM Please contact [email protected] or +61 2 87245218 for further assistance . Installation

NOTE: Recommended to not install this toilet using an offset pan connector when using the uniconnector to install the pan as this may cause flushing problems.

1 . Rough-in position for the waste outlet and floor fixing bracket holes.

ENGLISH Ensure that the water inlet connection is not obstructed by the toilet .

180

2 . Assemble the cistern to the pan . Place the foam coupling seal into the pan recess (do not use sealant). Connect the flexible hose to the inlet valve at the base of the cistern. Position the fixing bolts into the base of the cistern ensuring that the black washers are on the inside of the cistern. Lift the cistern over the pan. Line up the fixing bolts with the holes in the pan. Using the nuts and washers provided, tighten down the cistern evenly to the pan. Do not overtighten.

6 QTA021 Installation (continued)

3 . For back inlet connection, connect the flexible stainless steel hose to the BSP thread in the back of the wall. Ensure the inlet valve filter is

installed onto the inlet valve. ENGLISH

P TRAP INSTALLATION

4 . Set up the waste pipe to that the end of the pan collar extends 240 mm from finished wall. 180

P TRAP INSTALLATION

5 . Make sure that the inlet hose is pushed through hole in the side of the pan . Align and push the fully assembled pan and cistern back to the wall, connecting the pan spigot to the pan collar. Bucket flush and check for leaks .

7 CONGLOMKB .COM Please contact [email protected] or +61 2 87245218 for further assistance . Installation (continued)

S TRAP INSTALLATION Screw fitting 6 . Lubricate the rubber fins of the pan bend and position this in the waste pipe at the correct height . Fix the pan connector back to the wall using the screw fitting and collar. (The screw fittings need to

ENGLISH be cut down to size so that the pan connector is fixed in the vertical position .)

180 Plastic Remove the plastic cover and rubber from the front of the pan Rubber Cover connector . Cut the front of the pan connector down to the required length. Take care to ensure the cut is even and straight. Lubricate the rubber then replace it and then the plastic cap onto the pan connector .

S TRAP INSTALLATION

7 . Make sure the inlet hose is pulled through the hole inside of the pan . Align and push the fully assembled pan and cistern back to the wall, connecting the pan spigot into the pan connector. Bucket flush and check for leaks .

8 . Connect the cistern to the stop tap using the appropriate plumbing fittings. Ensure the inlet valve filter (supplied) is installed onto the inlet valve. (Warranty will be voided if the filter is not installed.) Fill the cistern to the correct height .

8 QTA021 Installation (continued)

9 . Ensure that the pan is level and that the cistern aligns with the wall. ENGLISH Make minor adjustments if necessary . (Note: walls may be out of square with floors which may create a gap behind the cistern. This can be covered up by using a suitable flexible gap filler.)

INSTALLING THE TOILET TO THE FLOOR

1 . The toilet should be installed on the flat concrete floor. 2 . Drill holes in the floor and insert the anchors (G) (see below). Attach the mounting bracket (C) with the washer (D) and mounting bracket screw (H) . 3 . Put on the toilet bowl and insert the washer (E) in the anchor hole of the toilet bowl . Tighten the mounting screw (J) to secure the toilet bowl and mounting bracket (C), put on the cap (F) . 4 . Once finished installing it to the floor, double check to make sure the toiletowl b is stable.

Toilet

F F J H H E J E

DD CC

Concrete G G

9 CONGLOMKB .COM Please contact [email protected] or +61 2 87245218 for further assistance . Installation (continued)

SEAT INSTALLATION

1 . Insert the expansion nuts (E) into the ceramic fixing holes. 2 . Insert the bolts (D) through the hinge plates (B), and fix them

ENGLISH to the nuts (E) . 3 . Adjust the hinges to fit the seat. Do not tighten all the way. D B D B

E E

Troubleshooting

Flush volume If the push rods are too short and not fully connecting with the glush valves, this may result in low flush volume. Readjust push rod height and ensure the bottom of the push rod is flush with the top surface of the valve cylinder.

Flush valve leaking If the push rods are too long, this may result in the flush valve leaking. Shorten push rods with the adjustments nuts .

Tank leaking from the valve To clean the valve seal or replace the entire unit: 1 . Turn cylinder counter clockwise and lift off . 2 . Clean the bottom of the flush valve seal and the top of the flush valve seat. 3 . Reverse this procedure to attach flush valve cylinder.

Care and Cleaning

For general cleaning, use a mild, nonabrasive soap and warm water. Do not use abrasive cleaners (such as cleaners that contain sand or silica that will scratch the china surface) . Common bowl cleaners may be used on the china surface of the bowl . Do not use “in-tank” bowl cleaners because they contain aggressive chemicals that attack the tank components (see warranty exclusions).

10 QTA021 Service Parts

If you are missing parts or if you require replacement parts, please contact our customer service team at [email protected] or +61 2 87245218 (Service available in English and French, Monday - Friday from 6:30am - 3pm AEDT). Identify the required part(s) and have the part number(s) ready . ENGLISH

FGH A D

B JKL E

Part Description Code Quantity A Covers QHT139 2 B Hinge Plates QHT140 2 C Bolts and Washer QHT141 2 D Expansion Nuts QHT130 2 E Mounting Brackets QHT132 2 F Metal Washers QHT133 2 G Washers QHT134 2 H Caps QHT135 2 J Anchors QHT136 2 K Mounting Bracket Screws QHT137 2 L Toilet Bowl Mounting Screws QHT138 2 M S Trap Adaptor QHT142 1

** Our goods come with guarantees that cannot be excluded under the Australian Consumer Law . You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fil to be of acceptable quality and the failure does not amount to a major failure.

11 CONGLOMKB .COM Please contact [email protected] or +61 2 87245218 for further assistance . Imported by:

101B Dublin Airport Business Park Swords Road, Santry Dublin 9, IRELAND D09 H5R7 +61 2 87245218 | [email protected] (service available Monday - Friday from 6:30 am - 3 pm AEDT) www.conglomkb.com

Made in China