Creform Tools
Creform Pipe should always be cut using a pipe cutter, band saw or chopsaw — never use a hand saw to cut pipe as this will frequently result in pipe sections not cut to the required lengths and pipe ends out of square. These conditions can effect the fit and strength of your Creform structures.
EPC1 EPC1A Electric ø28 Pipe Cutter Electric Pipe Cutter Blade
EK-1 EK-1A Manual ø28 & ø32 Pipe Cutter Manual Pipe Cutter Blade Set
SV-22 ID/OD DEBUR I.D. Deburring Cutter I.D/O.D. Deburring Tool G SE CTI O N
SV-22A Replacement Blade
EK-6 I.D. Deburring Cutter for Drill Please read all instructions and familiarize yourself with proper procedures prior to using the Creform EPC Pipe Cutter or EK-1 Manual Pipe Cutter.
ALWAYS WEAR APPROPRIATE EYE PROTECTION.
When cutting, always hold the longest length of pipe.
EK-6A Replacement Blade
800-839-8823 www.creform.com G- Power Saw for Cutting Creform Pipe and Conveyor
● UL listed single phase motor Manufacturer: ● Jet Exclusive design heavy-duty 14 gauge stand ● Large diameter wheels and built-in handle allows Creform P/N: easy movement Bandsaw J1 ● Front legs have adjustable leveling pads ● Ball bearing supported blade wheel Our Price: ● Full adjustable ball bearing blade guides $445.00 ● Heat treated and ground steel worm gear with bronze drive gear ● Three blade speeds to choose from ● Automatic shut-off after cut Standard Equipment ● Vertical work table ● Carbon steel blade ● Adjustable material stop
Specifications Model HVBS-56M Stock Number 414458 Round Capacity at 90 degrees (in): 5 Round Capacity at 45 degrees (in): 3 Rectangle Capacity at 90 degrees (in):5 x 6 Rectangle Capacity at 45 degrees (in):5 x 3 Throat Depth (in): 6 Vertical Workable (in): 9-5/8 x 9-1/2 Vise Swivels: 45 degrees Blade Size (in) 1/2 x .025 x 64-1/2 Blade Wheel Diameter (in): 7-3/8 Blade Speeds (SFPM): 80, 120, 200 Blade Height (in): 25-1/2 Floor Space Required (in): 19 x 44 Motor: 1/2 HP, 1 Ph 115/230V Prewired 115V Net Weight (lbs): 115
Creform Corporation, PO Box 830, Greer, SC 29652-0830 www.Creform.com Phone:864-877-7405 Fax:964-877-3863 Creform Tools
In addition to the EPC Pipe Cutter and the EK-1 Manual Pipe cutter, the tools below are available from Creform, intended to make fabrication and construction of Creform Structures easier and faster.
EK-20 M5-L M5-T Caster Wrench for YGR Casters 5mm Hex Wrench 5mm Hex Wrench, T-Handle
NDL-1 EY-204 BELLOW Needle Spout, Adhesive Adhesive Bottle with Needle Adhesive Bellows with Needle
RTK1 Set: Ratchet Handle, RM-01 5MTM 13mm Socket, 5mm Hex Bit Rubber Mallet Metric Tape Measure G SE CTI O N RTK1A
RTK1B RTK1C
CW-32 M6-L M6-L Caster Wrench for ESC Casters 6mm Hex Wrench 6mm Hex Wrench, T-Handle
800-839-8823 www.creform.com G-
Creform STAINLESS STEEL PIPE - 27MM
Dimensions are in millimeters.
SU7-4000-SUS Notes: Stainless Steel Pipe • High temperature applications up to 300°F (140°C). • Higher chemical resistance uses since material is 304SS. • The pipe is grooved at joint locations to add strength. ø28 Length (mm)
Material: Polished 304 Stainless Steel. Used to Form: General Creform Structures. Carts, workstations, flow racks, etc. Note: ø27 pipe. Standard length 4M.
Creform Standard 27mm Pipe Strength
Experimental Conditions • The pipe rests freely at room temperature on two supports • A force is applied at 1/2 A at a speed of 50mm/min
A Dimension Proportional Limit 900mm (2'11") 97kg (213 lbs.) * Proportional Limit refers to the point where any further force would permanently deform the pipe.
EK-2 EK-2A EK-3 EK-3A Manual Pipe Cutter for Manual Pipe Cutter Manual Grooving Cutter for Manual Grooving Cutter SUS Pipe Blade Set SUS Pipe Blade Set
EK-4 EK-4A EK-4B EK-6 I Electric Pipe Cutter - Electric SUS Pipe Cutter Electric SUS Pipe Grooving ID Deburring Tool for
Groover for SUS Pipe Blade Set Cutter Blade Set Electric Drill sect i on
EK-6A Replacement Blade
ESD anti static 800-839-8823 I-7 www.creform.com