Model T1213 Resaw Drift Bar Instructions

Total Page:16

File Type:pdf, Size:1020Kb

Model T1213 Resaw Drift Bar Instructions MODEL T1213 RESAW DRIFT BAR INSTRUCTIONS For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected] Introduction Recommended Tools The Model T1213 Resaw Drift Bar is designed Drill w/Guide or Drill Press ................................ 1 3 to help reduce blade lead (cut drift) by creating Drill Bit ⁄8" ......................................................... 1 a pivot point on the resaw fence that provides Center Punch..................................................... 1 more control during resaw operations. It can be Tape Measure .................................................... 1 7 installed on any resaw fence at least 5 ⁄8" tall. Installation NOTICE 1. DISCONNECT MACHINE FROM POWER! Installation of Model T1213 requires per- 2. Install a blade suitable for resaw operations. manent modification of your resaw fence! We suggest widest possible blade for your Before installing Model T1213, make sure machine with 2–4 TPI (hook or skip teeth) blade guides clear the top of resaw fence that is sharp and clean. 1 by at least ⁄2". 3. Install resaw fence and move it up to blade. If resaw fence is adjustable forward/back, make sure blade is centered lengthwise on resaw fence. 1 4. Mark top of resaw fence exactly ⁄4" forward of blade teeth (see Figure 2). 13 5. Mark a point exactly ⁄16" below mark made in Step 4 (see Figure 2). Center Mark 1 Figure 1. Model T1213 Resaw Drift Bar. ⁄4" Specifications 13 Weight .........................................................2 lbs. ⁄16" 1 1 Dimensions ......................................6 ⁄4"L x 1 ⁄4"D 7 Minimum Fence Height .................................5 ⁄8" Blade Resaw Drill Fence Here Figure 2. Location of center mark and hole point. COPYRIGHT © AUGUST, 2017 BY GRIZZLY INDUSTRIAL, INC. NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. #ES19023 PRINTED IN TAIWAN V1.10.17 6. Remove resaw fence from bandsaw. 6. If necessary for cutting operation, support ends of board with saw stand or roller stand. 7. Use center punch to score a point at mark 3 made in Step 5 and drill ⁄8" hole through 7. Turn bandsaw ON. resaw fence. 8. Slowly feed workpiece completely through Note: Use drill press or handheld drill with blade. Use drift bar as a pivot point to control guide to make sure hole is drilled perpendicu- cut, as shown in Figure 4. lar to resaw fence. Note: The drift bar allows you to steer your 8. Insert adjustable handle with fender wash- workpiece while cutting to quickly correct er through back of resaw fence (refer to blade lead and keep blade aligned with cut Parts Breakdown drawing). line. 9. Make sure drift bar is flat against resaw fence and straight up and down. Blade Operation Blade Guides 1. Install resaw fence with drift bar. Drift Cut Line Mark 2. Mark cut line from front to back on top of Bar workpiece (see Figure 3). Workpiece 3. Lower bandsaw blade guides as close to workpiece as possible (see Figure 3). 4. Adjust resaw fence so blade aligns with mark Figure 4. Resawing with drift bar. made in Step 2 and center of drift bar is set 1 ⁄4" forward of blade teeth (see Figure 3). Parts Breakdown & List 3 Blade Blade Drift Guides Bar Blade 1/4" Resaw Fence 2 1 Cut Line Drift Mark Bar Workpiece REF PART # DESCRIPTION Figure 3. Workpiece positioned to cut using 1 PT1213001 ADJ HANDLE 65L, M8-1.25 X 25 resaw fence with drift bar. 2 PT1213002 FENDER WASHER 8MM 3 PT1213003 RESAW DRIFT BAR 6-1/4" X 1-1/4" 5. Lock rip fence and resaw fence in position. -2- BUY PARTS ONLINE AT GRIZZLY.COM! Scan QR code to visit our Parts Store. π.
Recommended publications
  • Paul Sellers' Workbench Measurements and Cutting
    PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST NOTE When putting together the cutting list for my workbench, I worked in imperial, the system with which I am most comfortable. I was not happy, however, to then provide direct conversions to metric because to be accurate and ensure an exact fit this would involve providing measurements in fractions of millimetres. When I do work in metric I find it more comfortable to work with rounded numbers, therefore I have created two slightly different sets of measurements. This means that in places the imperial measurement given is not a direct conversion of the metric measurement given. Therefore, I suggest you choose one or other of the systems and follow it throughout. © 2017 – Paul Sellers v2 PAUL SELLERS’ WORKBENCH MEASUREMENTS AND CUTTING LIST WOOD QTY DESCRIPTION SIZE (IMPERIAL) SIZE (METRIC) (THICK X WIDE X LONG) (THICK X WIDE X LONG) 4 Leg 2 ¾” x 3 ¾” x 34 ⅜” 70 x 95 x 875mm 1 Benchtop 2 ⅜” x 12” x 66” 65 x 300 x 1680mm 2 Apron 1 ⅝” x 11 ½” x 66” 40 x 290 x 1680mm 1 Wellboard 1” x 12 ½” x 66” 25 x 320 x 1680mm 4 Rail 1 ½” x 6” x 26” 40 x 150 x 654mm 2 Bearer 1 ¼” x 3 ¾” x 25” 30 x 95 x 630mm 4 Wedge ⅝” x 1 ½” x 9” 16 x 40 x 228mm 4 Wedge retainer ⅝” x 1 ½” x 4” 16 x 40 x 100mm HARDWARE QTY DESCRIPTION SIZE (IMPERIAL) SIZE (METRIC) 1 Vise 9” 225mm Dome head bolts (including nuts and washers) for 4 ⅜” x 5” 10 x 130mm bolting legs to aprons 2 Lag screws (with washers) for underside of vise ½” x 2 ½” 12 x 65mm 2 Lag screws for face
    [Show full text]
  • Snap on On-Site Power Generation Tool Kit Price $ 3095 Sales Tax $185.70 Total $3280.70 Student Name Student ID Email
    Pennsylvania College of Technology Snap On On-Site Power Generation 1650 Pry bar, 16" 211FY Socket Set, Shallow, 12-Pt 3/8 Drive, (11 pc)(1/4" to 7/8") 211SFSY Socket Set, Deep, 6-Pt 3/8 drive, (11 pcs.) (1/4" to 7/8") 212SFSMY Socket Set, Metric, Deep, 6-Pt (12 pcs.) 3/8 drive (8 to 9 mm) 313SMYA Socket Set, Metric, Deep, 12-Pt (13 pcs.) 1/2 drive (12-24 mm) 313SWMYA Socket Set, Metric, Shallow, 12-Pt (13 pcs.) 1/2 drive (12-24 mm) 313SYA Socket Set, Deep, 12-Pt (13 pcs.) 1/2 drive (3/8" to 1 1/8") 317MPC General Set, Standard Shallow, 12-Pt (17 pcs.) 1/2 drive (3/8" to 1 1/8") AWP120 Adjustable Joint, Straight Serrated Jaws, 12 3/4" BP24B Hammer, Ball Peen, 24 oz. MAGM2A03H Flashlight ( was ECF2B discontinued) OEX709B Set, Wrench, Combination, 12-Pt (9 pcs. in tray) (3/8" to 7/8") OEXM710B Set, Wrench, Combination, Metric, 12-Pt (10 pcs. in tray) (10-19 mm) SHDX60R Set Screwdriver, Combination, Instinct Hard Handle, Red 6 pcs. QD3R250 Torque Wrench, Adj. Click-type, Fixed-Ratchet PPC710BK Punch and Chisel Set, 11 pc. (Center/Pin/Starter) FXK11 Extension, Knurled, Friction Ball, 11" 3/8 Drive PPB1226A Punch, Drift, Bronze, 13/16" point, 12 FXK3 Extension, Knurled, Friction Ball, 3" GLASS1BK Glasses, Safety, Clear Lens/Black Frames HBFE24 Hammer, Dead Blow, Soft Grip, 24 oz. OEX30B 15/16" Standard Combination Wrench OEX32B 1" Standard Combination Wrench OEX36B 1 1/8" Standard Combination Wrench OEX40B 1 1/4" Standard Combination Wrench OEXM80B 8mm Metric Combination Wrench PK23A Scraper PL300CF Set, Cutters/Pliers, 3 pcs.
    [Show full text]
  • Flowpath User's Guide
    FlowPATH User’s Guide M-320 Version 6.02 FLOWMASTER® FlowPATH User's Guide Due to continuing product improvement, the information contained in this document is subject to change without notice. Flow International Corporation shall not be held liable for technical or editorial omissions made herein, nor for any incidental or consequential damage resulting from the use of this material. This document contains information protected by copyright. The software described in this document is furnished under a license agreement. The software may be used or copied only in accordance with the terms of the license agreement. No part of this document shall be reproduced or transmitted in any manner without prior written consent from Flow International Corporation. DISCLAIMER All technical data and information provided in this software is done as a service to customers of Flow In- ternational Corporation (“Flow”) and consumers of our products. All names, designs, and model numbers of products are trademarks of their respective manufacturers. Specifications of products are subject to change without notice or obligation. Manufacturers may also change or discontinue models of their prod- ucts without notice or obligation. While Flow endeavors to provide accurate information and descriptions of products, accuracy and completeness cannot be guaranteed. Flow is not responsible for, nor does it have any liability for any incomplete information, inaccurate CAD files, mistakes or typographical errors, including liability for incidental, consequential, or special damages. All products should be inspected and measured promptly upon delivery and certainly before any improvements or alterations are done in antici- pation of or preparation for installation. Flow assumes no liability for the use of such information or for any damages incurred through its use or application.
    [Show full text]
  • Catalog Insert
    PRODUCT CATALOG Vol.12 KOMELON Corporation The world’s most vertically integrated measuring tape manufacturer. From our raw material manufacturing plant to global marketing and distribution, KOMELON handles it all with the most advanced and innovative KOMELON Corporation R & D technology. This assures our customers the highest quality products available. For over 50 years, Komelon has manufactured a full line of quality measuring tools with dedication and a passion for craftsmanship while supplying markets throughout the world. Komelon Corporation - Korea, Since 1963 KOMELON Steel This is the corporate headquarters housing all product design, engineering and research & development. This facility also manufactures the Meter-Man Measuring wheel line. Komelon Steel Corporation - Korea, Since 1995 Komelon manufacturers its own steel strip material for all blades and springs used in tape measure production. This ensures the highest quality tape KOMELON China measures on the market. Komelon China, Since 2002 This state-of-the art measuring tool manufacturing facility, located in Qingdao, China was recently built to better serve Komelon’s rapidly growing wordwide sales. KOMELON USA Division Komelon USA Division, Since 1997 This sales and distribution center for North America warehouses high inventory levels to ensure fast shipments and superior customer service. Komelon SAW - Korea, Since 2012 Komelon Saw manufacturing facility located in Daegu, S.Korea is an industry leading manufacturer of high end pruning saws KOMELON Saw - Korea Contents
    [Show full text]
  • Laying Instructions
    1 2 3 4 5 AREA OF USE SUBSTRATES INSTALLATION FIRST USE MAINTENANCE Residential use, temperature-regulated interior room + 8 < T < + 35°C. Loose laying is allowed as long as the ambient temperature is regulated and the floor temperature doesn’t exceed 60°C This floor covering cannot be laid on verandas. IMPORTANT: The information in this document is valid from: 01/06/2021 and is subject to change without notice. In the face of continuous technical improvements, before starting any work, our customers should check with us that this document is still in force. RESIDENTIAL FLOORING 1 2 3 4 5 AREA OF USE SUBSTRATES INSTALLATION FIRST USE MAINTENANCE 1. GENERAL The flooring must be laid on a flat, clean, sound, dry and solid The moisture content must not exceed 7% with a carbide substrate. moisture test. < 5 mm < 1 mm < 13/64" < 3/64" The flatness tolerance must be < 5 mm under a 2 meters The substrate must not have any uneven areas > 1 mm every straight edge. 20 cm. 2. RECOMMANDATIONS BY SUBSTRATE TYPE Substrate Conditions If joint < 5 mm width < 2 mm depth. Otherwise, apply a grouting product or levelling Ceramic Tiles compound to eliminate irregularities. Concrete Floor, Painted Concrete, Levelling Concrete, Substrate moisture content < 7%. liquid cement-based screed If necessary, apply a levelling compound to eliminate any surface irregularities. Anhydrite Substrate moisture content < 0,5 %. Compact Vinyl Removal mandatory. If necessary, apply a levelling compound to eliminate any Acoustic Vinyl , Carpet , Laminate surface irregularities. If not glued and nailed onto spaced battens. If glued, removal mandatory.
    [Show full text]
  • Measuring and Layout
    DRILLING DRILLING MEASURING AND LAYOUT TAPE MEASURES CHALK LINES/PLUMB BOBS DIGITAL MEASURING PRECISION MEASURING RULERS/SQUARES LEVELS PROTRACTORS MARKING TOOLS AND FLAGGING TAPES Measuring and Layout 1 TAPE MEASURES INDUSTRIAL TAPE MEASURES - SAE INDUSTRIAL TAPE MEASURES - SAE/METRIC • Durable nylon coated blade • Durable nylon coated blade • High contrast blade for easy reading • High contrast blade for easy reading • Impact resistant case with rubberized grip • Impact resistant case with rubberized grip • Easy slide lock in any position • Easy slide lock in any position Item # Size Item # Size 27904 1" x 16' 27902 5/8" x 10' (3M) 27906 1" x 25' 27908 1" x 25' (7.5M) NEW PROFESSIONAL TAPE MEASURES - SAE/ PROFESSIONAL TAPE MEASURES - SAE METRIC • Impact resistant rubberized case • Impact resistant rubberized case • Easy-to-read black and red markings • Easy-to-read black and red markings • Slide-down bar locks tape in any position • Slide-down bar locks tape in any position • Tru-zero hook and removable belt clip • Tru-zero hook and removable belt clip Item # Size Item # Size Item # Size Item # Size 27914 1" x 16' 27922 1-1/4" x 16' 27916 1" x 16' (5M) 27924 1-1/4" x 16' (5M) 27918 1" x 25' 27926 1-1/4" x 25' 27920 1" x 25' (7.5M) 27928 1-1/4" x 25' (7.5M) 2 Measuring and Layout Tape Measures/Long Tapes NEW 1" X 25' TAPE MEASURE FRACTIONAL 1" X 25' (7.5M) TAPE MEASURE MARKINGS - SAE DOUBLE SIDED - SAE/METRIC • Easy read fractional markings • Best when taking measurements at a height • Impact resistant rubberized case • Impact resistant
    [Show full text]
  • Measuring and Marking Timber
    Hand woodworking Hand woodworking on the end is a millimetre thick, then Checking the width using a the tabs should move by 1mm; this GemRed digital Vernier calliper is so you can measure either internal or external measurements. The offset between the movements in this tape measure should be set but if the tape is dropped or the tab is bent, then the accuracy has been lost. If we do need to measure a longer distance, we would try to hold the tape measure The Richter tape measure can to start on the 100mm mark and then also be used like a pair subtract 100mm after measuring. of compasses Whenever we are buying timber or are in our timber storeroom, we always use these tape measures. At this point strangely enough, we often talk in feet and inches. Once we take our timber into our machine shop, we naturally convert to working in millimetres and use more accurate measuring equipment! We find it easier to talk in feet and inches when buying timber and converting it, but we just find it is far more accurate to work in millimetres when reworking Above: Fat Max and Richter the timber. This is a strange anomaly of tape measures woodworking that is still present over Right: The Richter tape measure PHOTOGRAPHS BY PETER SEFTON 40 years after decimalisation – we also taking an internal measurement tend to buy 8’ × 4’ 18mm thick! using the viewing window MEASURING STEEL RULES These tape measures are great, but when it comes to accurate work we and will always use a solid steel rule.
    [Show full text]
  • Achieving Perfect Angles Is a Common Pursuit in Woodworking—Especially
    The Deal Square By Tim Snyder chieving perfect angles is a common pursuit in Awoodworking—especially E 90° angles. But there’s no such thing as the perfect layout tool to check for square. at’s because the square relationships that occur in woodworking B C D F are surprisingly variable. One moment you’re squaring a bandsaw’s blade to its table; the next, you’re squaring a line across a full sheet of plywood or testing the corners of a frame-and-panel assembly. Handling these layout, A assembly, and alignment tasks with accuracy and e ciency has spawned an amazing variety of tools. e selection featured here is far from complete, but there’s H I a good chance you’ll nd a tool or two that deserves to be added to your arsenal. Having a good selection of squares is only part of the square deal. It’s also important to store these tools correctly— so that they’re protected but easily accessible. Jim Downing designed and built the beautiful case shown here. Make the case. A Starrett 4" double square ($84.50) See p. 56 for Here’s a pocket-sized square that gets plenty directions on of use because of its accuracy and easy making your own adjustability. Unlike cheap versions, this one custom tool cabinet. is calibrated down to 64ths of an inch. 52 Get the right angle on equipping D Mechanical pencils ($7.00 - $10.00) These marvelous markers never need sharpening your workshop with these and always lay down a uniform line.
    [Show full text]
  • Handout 1.Tools
    HANDOUT 1.TOOLS: A tool is an object made to help the man constructing, repairing, or modifying other objects. E.g.: Wrench Drill Hammer Screwdriver L We can classify them in tools and power tools, power tools are those that have a motor (e.g.: a drill) All the different tools have different uses, we have to use them properly for the use they have been designed. 1. Draw a tool you know, find the name and the use of it in English and Catalan and write it under your drawing. Use the dictionary and the help of your classmates and the teacher. English Catalan Name: Nom: Operation: Acció: 2. Now write the name of all the tools all the class has found: English Català Name Operation Nom Acció Wrench Turn Clau fixa Cargolar Miquel Llaràs Lesson 1-TOOLS HANDOUT 2.TOOLS TABLE: Here’s a list of the most common tools in the workshop of the school: Rasp hacksaw Coping saw handsaw gimlet clamp C-clamp pliers Needle-nose pliers Round nose pliers Wire stripping pliers shears Hammer Ball-peen hammer Nilon mallet Riveting tool Rubber mallet Wrench (spanner) Flat head screwdriver Hot glue gun Torx screwdriver Flat Round file Bench vice file k Drill allen key Adjustable spanner Miquel Llaràs Lesson 1-TOOLS HANDOUT 3. EMPTY TABLE: 3. Now hide the page you have been using before and in groups try to write all the names Miquel Llaràs Lesson 1-TOOLS HANDOUT 4.OPERATIONS: 1. These are different operations we can do with the tools in the workshop.
    [Show full text]
  • A Tailored Suit Printable Tape Measure You Need
    A Tailored Suit Printable Tape Measure You Need • A Printer • Scissors • Clear Tape • A Crisp New US Dollar Bill (Any denomination) Assembly Instructions 1. Print the tape measure (see instructions below) 2. Ensure the printed tape measure is accurate by using it to measure a dollar note; a dollar (any denomination) is 6.125 inches in length (give or take 1/16 an inch). If you are off by .125 (1/8) inch or more, ensure you are printing true to size by checking your printing preferences (see below). If you continue to be off by .125 or more, contact us and we’ll ship you a free tape measure immediately. 3. Carefully cut out all 8 pieces of the tape measure. 4. Connect each strip in order as indicated using tape – tape both sides and ensure the overlap is behind the measurement side. Glue can be used in a pinch, but is not recommended. 5. Smaller men do not need to attach the last piece (64 to 72 inches). 6. If you have a ruler or yard stick, use it to check for accuracy. Otherwise, you want to spot check between taped pieces with a dollar note to ensure final accuracy. The measurement tape is ready for use. Adobe Acrobat Printing Instructions The goal here is to print this tape measure true to size. Depending on your version of Acrobat Reader, "Fit to page" or "Shrink oversized pages to paper size" should NOT be checked. If you have: Acrobat Reader 6, 7,or 8 select "none” in the drop down next to "Page Scaling" option.
    [Show full text]
  • 41-Stocked Shop Version 3.Indd
    Well-Stocked Shop Must-Have Measuring Tools Stanley 25' Fat Max Measurements you can count on Tape, The Home Depot, #655095, $19.97 By Matt hew Teague While good measuring Combinati on square tools don’t guarantee quality Place a quality square at the top but some prefer a 6" hook work, quality work is impossible of your list. You’ll use it to the set rule,A 6" because �lat rule it iscatches more versatile,the without them. Your shop a saw blade height and to adjust edges or ends of stock for easy should contain squares, rules, blade angles to 45° or 90°. The reference. Just make sure the and tapes that are intuitive to adjustable blade allows you check hook is removable–otherwise use, easy to read, and rugged the depth of mortises, grooves, or it can get in the way on certain enough to maintain accuracy offset parts. Also, the blade can tasks. To work as it should, even after years of use. serve as a ruler or straightedge. markings should start and Here’s a short list of tools Combination squares range needed to complete most any in size from 4" to 36", but a 12" with combination squares, opt furniture project and to make blade proves the most versatile. end �lush to the rule’s end. As precision machine setups. A quality square features a Considering the low cost of 24"for a satinor 36" �inished shop blade. rule some of the items, you might measurements–64ths if possible. A longer, stable, and reliable rule buy a few spares to ensure that Toblade ensure that’s that divided the blade into �inereads will come in handy for a variety the right tool is within easy well and stays that way, select of larger jobs.
    [Show full text]
  • How to Read a Tape Measure the “Complete” Full Inch Mark
    HOW TO READ A TAPE MEASURE THE “COMPLETE” FULL INCH MARK 1/ 16 3/ 16 5/ 16 7/ 16 9/ 16 11/ 16 13/ 16 15/ 16 1/ 8 3/ 8 5/ 8 7/ 8 1/ 4 3/ 4 1/ 2 0 1 THE "COMPLETE" FULL INCH MARK NOTE THAT THE TOP NUMBER (NUMERATOR) IS ALWAYS ODD. ( 1, 3, 5, 7, 9, 11, 13, 15 ) NOTE THAT THE BOTTOM NUMBER (DENOMINATOR) IS ALWAYS EVEN. ( 2, 4, 8, 16 ) THE “COMPLETE” FULL INCH MARK • It is vitally important that each of you are very proficient in reading a tape measure or rule. • We will now break the markings down into logical groups so that you can understand the pattern that makes reading the tape measure easy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
    [Show full text]