Design a 3-Input CMOS NAND Gate (PUN/PDN) with Fan-Out of 3. Total Output Load of the NAND Gate Is Equal to 15Ff and Μn/Μp = 2.5

Total Page:16

File Type:pdf, Size:1020Kb

Design a 3-Input CMOS NAND Gate (PUN/PDN) with Fan-Out of 3. Total Output Load of the NAND Gate Is Equal to 15Ff and Μn/Μp = 2.5 Tutorial on Transistor Sizing Problem #1 (Static CMOS logic): Design a 3-input CMOS NAND gate (PUN/PDN) with fan-out of 3. Total output load of the NAND gate is equal to 15fF and µn/µp = 2.5. For 0.35µm process technology tox = -9 -12 7.6*10 m, εox = 35*10 F/m. Compare the above design with that of a 3-input NOR (PUN/PDN) gate. State any benefits of one implementation over the other. For the sake of simplicity assume all capacitance is lumped and gate capacitance neglecting diffusion and wiring capacitance. Solution: Cox = εoxWL/ tox = 15fF. So W = 9.2µm. Leff = 0.35µm. Assuming output load is all gate capacitance. This is a simplifying assumption made for this problem. A more realistic approach would be to calculate the diffusion and wiring capacitances as well. Equivalent inverter for fan-out of 3 and µn/µp = 2.5 would result in: A B C 2.23 2.23 2.23 Wp = 2.5*Wn for equal rise and fall times. Also, Wp + Wn = 9.2/3 = 3.16µm for fan-out of 3. A 2.67 B Solving the above equations we have, 2.67 C 2.67 Wp = 2.23µm and Wn = 0.89µm. NAND implementation: NAND implementation Therefore, for the 3-ip NAND gate implementation, each PDN n-MOS transistor will be: 3*0.89µm = 2.67µm A and each p-MOS transistor in the PUN network will be: 2.23µm 6.69 B NOR implementation: 6.69 For a 3-ip NOR gate implementation, each PDN n-MOS transistor C will be: 0.89µm 6.69 A BC Each PUN p-MOS transistor will be 3*2.23µm = 6.69µm 0.89 0.89 0.89 Area comparison: NOR implementation Total gate area of NAND gate is: 3*(2.67+2.23)µm = 14.7µm Total gate area of NOR gate is: 3*(6.69+0.89) µm = 22.7µm Thus we infer that the NAND gate has less area and power compared to the NOR gate for identical loading and fan-out conditions and is the preferred implementation. Problem #2 (Dynamic Gate): Consider the following circuit: A 3 input n-MOS dynamic gate, driving an output inverter followed by a capacitive load. For the data in Problem #1 design the n-MOS dynamic gate and inverter for a fan-out of 3 between stages. Solution: The total load being driven is equivalent to a transistor width of 9.2um. The load is driven by a dynamic gate followed by an inverter. The inverter size for a fan-out of 3 is equal to that in the above problem and is given by p-MOS = 2.23um and n-MOS = 0.89um. So, the total load being driven by the dynamic gate is equal to 3.16um. For a fan-out of 3, the equivalent width for the inverter representing the dynamic stage should be equal to 3.16/3 = 1.05um. Applying the same equations as in Problem #1, we have: p-MOS + n-MOS = 1.05um. p-MOS = 2.5n-MOS. So, 3.5n-MOS = 1.05/3.5um. n-MOS = 0.3um and p-MOS = 2.5*0.3um = 0.75um For the 3-input dynamic gate there are 4 n-MOS transistors in series. So, each n-MOS transistor is 4*0.3um = 1.2um Problem #3 (Transmission Gate): Consider a circuit as follows: An inverter driving a transmission gate driving a capacitive load (all three in series). Design the transmission gate and inverter when the lumped capacitive load is equal 30fF. In addition, assume that there is wiring capacitance of 15fF as well. Design the inverter for a fan-out of 2 for high performance. Assume µn = 0.04m2/Vs, µp = 0.016m2/Vs, Vtn = |Vtp| = 0.7, Vdd = 3.3V. Size the TG to ensure the equivalent RC delay to be equal to 18ps. Solution: Total capacitance at output of TG = load capacitance + wiring capacitance = 45fF. RC delay = 18ps implies that R = 18*10-12/45*10-15 = 400 Ohm Req = 1/[(kn(Vdd-Vtn) + kp(Vdd-|Vtp|)] Where kn = µnWnCox/L Substituting the given values from above in the equation, we obtain n-MOS = 0.89um and p-MOS = 2.23um. The inverter driving the TG and capacitive load sees a load equal to the diffusion capacitance of the TG + the capacitive load (9.2um). We assume that the diffusion capacitance of a transistor is approximately equal to 1/3 of its gate capacitance. Hence, the capacitive load offered by the TG = (p-MOS + n-MOS)/3 = 3.16/3 = 1.05um. Thus the total load at the output of the inverter = load of TG (1.05um) + load of output capacitance (9.2um) = 10.25um. The driving inverter needs to be designed for a fan-out of 2 for a total output load of 10.25um. Thus the p-MOS + n-MOS width of the inverter = 10.25/2 = 5.13um For equal rise and fall times, p-MOS = 2.5n-MOS. So, 3.5n-MOS = 5.13um, n-MOS = 1.47 and p-MOS = 2.5*1.47 = 3.68um .
Recommended publications
  • Transistors and Logic Gates
    Introduction to Computer Engineering CS/ECE 252, Spring 2013 Prof. Mark D. Hill Computer Sciences Department University of Wisconsin – Madison Chapter 3 Digital Logic Structures Slides based on set prepared by Gregory T. Byrd, North Carolina State University Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. Transistor: Building Block of Computers Microprocessors contain millions of transistors • Intel Pentium II: 7 million • Compaq Alpha 21264: 15 million • Intel Pentium III: 28 million Logically, each transistor acts as a switch Combined to implement logic functions • AND, OR, NOT Combined to build higher-level structures • Adder, multiplexer, decoder, register, … Combined to build processor • LC-3 3-3 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. Simple Switch Circuit Switch open: • No current through circuit • Light is off • Vout is +2.9V Switch closed: • Short circuit across switch • Current flows • Light is on • Vout is 0V Switch-based circuits can easily represent two states: on/off, open/closed, voltage/no voltage. 3-4 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. N-type MOS Transistor MOS = Metal Oxide Semiconductor • two types: N-type and P-type N-type • when Gate has positive voltage, short circuit between #1 and #2 (switch closed) • when Gate has zero voltage, open circuit between #1 and #2 Gate = 1 (switch open) Gate = 0 Terminal #2 must be connected to GND (0V). 3-5 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. P-type MOS Transistor P-type is complementary to N-type • when Gate has positive voltage, open circuit between #1 and #2 (switch open) • when Gate has zero voltage, short circuit between #1 and #2 (switch closed) Gate = 1 Gate = 0 Terminal #1 must be connected to +2.9V.
    [Show full text]
  • Universal Gate - NAND Digital Electronics 2.2 Intro to NAND & NOR Logic
    Universal Gate - NAND Digital Electronics 2.2 Intro to NAND & NOR Logic Universal Gate – NAND This presentation will demonstrate • The basic function of the NAND gate. • How a NAND gate can be used to replace an AND gate, an OR gate, or an INVERTER gate. • How a logic circuit implemented with AOI logic gates can Universal Gate – NAND be re-implemented using only NAND gates. • That using a single gate type, in this case NAND, will reduce the number of integrated circuits (IC) required to implement a logic circuit. Digital Electronics AOI Logic NAND Logic 2 More ICs = More $$ Less ICs = Less $$ NAND Gate NAND Gate as an Inverter Gate X X X (Before Bubble) X Z X Y X Y X Z X Y X Y Z X Z 0 0 1 0 1 Equivalent to Inverter 0 1 1 1 0 1 0 1 1 1 0 3 4 Project Lead The Way, Inc Copyright 2009 1 Universal Gate - NAND Digital Electronics 2.2 Intro to NAND & NOR Logic NAND Gate as an AND Gate NAND Gate as an OR Gate X X Y Y X X Z X Y X Y Y Z X Y X Y X Y Y NAND Gate Inverter Inverters NAND Gate X Y Z X Y Z 0 0 0 0 0 0 0 1 0 0 1 1 Equivalent to AND Gate Equivalent to OR Gate 1 0 0 1 0 1 1 1 1 1 1 1 5 6 NAND Gate Equivalent to AOI Gates Process for NAND Implementation 1.
    [Show full text]
  • EE 434 Lecture 2
    EE 330 Lecture 6 • PU and PD Networks • Complex Logic Gates • Pass Transistor Logic • Improved Switch-Level Model • Propagation Delay Review from Last Time MOS Transistor Qualitative Discussion of n-channel Operation Source Gate Drain Drain Bulk Gate n-channel MOSFET Source Equivalent Circuit for n-channel MOSFET D D • Source assumed connected to (or close to) ground • VGS=0 denoted as Boolean gate voltage G=0 G = 0 G = 1 • VGS=VDD denoted as Boolean gate voltage G=1 • Boolean G is relative to ground potential S S This is the first model we have for the n-channel MOSFET ! Ideal switch-level model Review from Last Time MOS Transistor Qualitative Discussion of p-channel Operation Source Gate Drain Drain Bulk Gate Source p-channel MOSFET Equivalent Circuit for p-channel MOSFET D D • Source assumed connected to (or close to) positive G = 0 G = 1 VDD • VGS=0 denoted as Boolean gate voltage G=1 • VGS= -VDD denoted as Boolean gate voltage G=0 S S • Boolean G is relative to ground potential This is the first model we have for the p-channel MOSFET ! Review from Last Time Logic Circuits VDD Truth Table A B A B 0 1 1 0 Inverter Review from Last Time Logic Circuits VDD Truth Table A B C 0 0 1 0 1 0 A C 1 0 0 B 1 1 0 NOR Gate Review from Last Time Logic Circuits VDD Truth Table A B C A C 0 0 1 B 0 1 1 1 0 1 1 1 0 NAND Gate Logic Circuits Approach can be extended to arbitrary number of inputs n-input NOR n-input NAND gate gate VDD VDD A1 A1 A2 An A2 F A1 An F A2 A1 A2 An An A1 A 1 A2 F A2 F An An Complete Logic Family Family of n-input NOR gates forms
    [Show full text]
  • Digital IC Listing
    BELS Digital IC Report Package BELS Unit PartName Type Location ID # Price Type CMOS 74HC00, Quad 2-Input NAND Gate DIP-14 3 - A 500 0.24 74HCT00, Quad 2-Input NAND Gate DIP-14 3 - A 501 0.36 74HC02, Quad 2 Input NOR DIP-14 3 - A 417 0.24 74HC04, Hex Inverter, buffered DIP-14 3 - A 418 0.24 74HC04, Hex Inverter (buffered) DIP-14 3 - A 511 0.24 74HCT04, Hex Inverter (Open Collector) DIP-14 3 - A 512 0.36 74HC08, Quad 2 Input AND Gate DIP-14 3 - A 408 0.24 74HC10, Triple 3-Input NAND DIP-14 3 - A 419 0.31 74HC32, Quad OR DIP-14 3 - B 409 0.24 74HC32, Quad 2-Input OR Gates DIP-14 3 - B 543 0.24 74HC138, 3-line to 8-line decoder / demultiplexer DIP-16 3 - C 603 1.05 74HCT139, Dual 2-line to 4-line decoders / demultiplexers DIP-16 3 - C 605 0.86 74HC154, 4-16 line decoder/demulitplexer, 0.3 wide DIP - Small none 445 1.49 74HC154W, 4-16 line decoder/demultiplexer, 0.6wide DIP none 446 1.86 74HC190, Synchronous 4-Bit Up/Down Decade and Binary Counters DIP-16 3 - D 637 74HCT240, Octal Buffers and Line Drivers w/ 3-State outputs DIP-20 3 - D 643 1.04 74HC244, Octal Buffers And Line Drivers w/ 3-State outputs DIP-20 3 - D 647 1.43 74HCT245, Octal Bus Transceivers w/ 3-State outputs DIP-20 3 - D 649 1.13 74HCT273, Octal D-Type Flip-Flops w/ Clear DIP-20 3 - D 658 1.35 74HCT373, Octal Transparent D-Type Latches w/ 3-State outputs DIP-20 3 - E 666 1.35 74HCT377, Octal D-Type Flip-Flops w/ Clock Enable DIP-20 3 - E 669 1.50 74HCT573, Octal Transparent D-Type Latches w/ 3-State outputs DIP-20 3 - E 674 0.88 Type CMOS CD4000 Series CD4001, Quad 2-input
    [Show full text]
  • Additional Gates and Circuits, Other Gate Types, Exclusive-OR Operator and Gates, High-Impedance Outputs 5
    Introduction to Digital Logic Course Outline 1. Digital Computers, Number Systems, Arithmetic Operations, Decimal, Alphanumeric, and Gray Codes 2. Binary Logic, Gates, Boolean Algebra, Standard Forms 3. Circuit Optimization, Two-Level Optimization, Map Manipulation, Multi-Level Prof. Nizamettin AYDIN Circuit Optimization 4. Additional Gates and Circuits, Other Gate Types, Exclusive-OR Operator and Gates, High-Impedance Outputs 5. Implementation Technology and Logic Design, Design Concepts and Automation, The Design Space, Design Procedure, The major design steps [email protected] 6. Programmable Implementation Technologies: Read-Only Memories, Programmable Logic Arrays, Programmable Array Logic,Technology mapping to programmable [email protected] logic devices 7. Combinational Functions and Circuits 8. Arithmetic Functions and Circuits 9. Sequential Circuits Storage Elements and Sequential Circuit Analysis 10. Sequential Circuits, Sequential Circuit Design State Diagrams, State Tables 11. Counters, register cells, buses, & serial operations 12. Sequencing and Control, Datapath and Control, Algorithmic State Machines (ASM) 13. Memory Basics 1 2 Introduction to Digital Logic Other Gate Types • Why? – Implementation feasibility and low cost – Power in implementing Boolean functions Lecture 4 – Convenient conceptual representation Additional Gates and Circuits • Gate classifications – Primitive gate - a gate that can be described using a single – Other Gate Types primitive operation type (AND or OR) plus an optional – Exclusive -OR Operator and Gates inversion(s). – High -Impedance Outputs – Complex gate - a gate that requires more than one primitive operation type for its description • Primitive gates will be covered first 3 4 Buffer NAND Gate • A buffer is a gate with the function F = X: • The basic NAND gate has the following symbol, illustrated for three inputs: XF – AND-Invert (NAND) • In terms of Boolean function, a buffer is the X Y (F X, ,Y Z) === X ⋅⋅⋅ Y ⋅⋅⋅ Z same as a connection! Z • So why use it? • NAND represents NOT AND , i.
    [Show full text]
  • Static CMOS Circuits
    Static CMOS Circuits • Conventional (ratio-less) static CMOS – Covered so far • Ratio-ed logic (depletion load, pseudo nMOS) • Pass transistor logic ECE 261 Krish Chakrabarty 1 Example 1 module mux(input s, d0, d1, output y); assign y = s ? d1 : d0; endmodule 1) Sketch a design using AND, OR, and NOT gates. ECE 261 Krish Chakrabarty 2 1 Example 1 module mux(input s, d0, d1, output y); assign y = s ? d1 : d0; endmodule 1) Sketch a design using AND, OR, and NOT gates. ECE 261 Krish Chakrabarty 3 Example 2 2) Sketch a design using NAND, NOR, and NOT gates. Assume ~S is available. ECE 261 Krish Chakrabarty 4 2 Example 2 2) Sketch a design using NAND, NOR, and NOT gates. Assume ~S is available. ECE 261 Krish Chakrabarty 5 Bubble Pushing • Start with network of AND / OR gates • Convert to NAND / NOR + inverters • Push bubbles around to simplify logic – Remember DeMorgan’s Law ECE 261 Krish Chakrabarty 6 3 Example 3 3) Sketch a design using one compound gate and one NOT gate. Assume ~S is available. ECE 261 Krish Chakrabarty 7 Example 3 3) Sketch a design using one compound gate and one NOT gate. Assume ~S is available. ECE 261 Krish Chakrabarty 8 4 Compound Gates • Logical Effort of compound gates ECE 261 Krish Chakrabarty 9 Example 4 • The multiplexer has a maximum input capacitance of 16 units on each input. It must drive a load of 160 units. Estimate the delay of the NAND and compound gate designs. H = 160 / 16 = 10 B = 1 N = 2 ECE 261 Krish Chakrabarty 10 5 NAND Solution ECE 261 Krish Chakrabarty 11 NAND Solution ECE 261 Krish Chakrabarty 12 6 Compound Solution ECE 261 Krish Chakrabarty 13 Compound Solution ECE 261 Krish Chakrabarty 14 7 Example 5 • Annotate your designs with transistor sizes that achieve this delay.
    [Show full text]
  • Hardware Abstract the Logic Gates References Results Transistors Through the Years Acknowledgements
    The Practical Applications of Logic Gates in Computer Science Courses Presenters: Arash Mahmoudian, Ashley Moser Sponsored by Prof. Heda Samimi ABSTRACT THE LOGIC GATES Logic gates are binary operators used to simulate electronic gates for design of circuits virtually before building them with-real components. These gates are used as an instrumental foundation for digital computers; They help the user control a computer or similar device by controlling the decision making for the hardware. A gate takes in OR GATE AND GATE NOT GATE an input, then it produces an algorithm as to how The OR gate is a logic gate with at least two An AND gate is a consists of at least two A NOT gate, also known as an inverter, has to handle the output. This process prevents the inputs and only one output that performs what inputs and one output that performs what is just a single input with rather simple behavior. user from having to include a microprocessor for is known as logical disjunction, meaning that known as logical conjunction, meaning that A NOT gate performs what is known as logical negation, which means that if its input is true, decision this making. Six of the logic gates used the output of this gate is true when any of its the output of this gate is false if one or more of inputs are true. If all the inputs are false, the an AND gate's inputs are false. Otherwise, if then the output will be false. Likewise, are: the OR gate, AND gate, NOT gate, XOR gate, output of the gate will also be false.
    [Show full text]
  • Chapter 6 - Combinational Logic Systems GCSE Electronics – Component 1: Discovering Electronics
    Chapter 6 - Combinational logic systems GCSE Electronics – Component 1: Discovering Electronics Combinational logic systems Learners should be able to: (a) recognise 1/0 as two-state logic levels (b) identify and use NOT gates and 2-input AND, OR, NAND and NOR gates, singly and in combination (c) produce a suitable truth table from a given system specification and for a given logic circuit (d) use truth tables to analyse a system of gates (e) use Boolean algebra to represent the output of truth tables or logic gates and use the basic Boolean identities A.B = A+B and A+B = A.B (f) design processing systems consisting of logic gates to solve problems (g) simplify logic circuits using NAND gate redundancy (h) analyse and design systems from a given truth table to solve a given problem (i) use data sheets to select a logic IC for given applications and to identify pin connections (j) design and use switches and pull-up or pull-down resistors to provide correct logic level/edge-triggered signals for logic gates and timing circuits 180 © WJEC 2017 Chapter 6 - Combinational logic systems GCSE Electronics – Component 1: Discovering Electronics Introduction In this chapter we will be concentrating on the basics of digital logic circuits which will then be extended in Component 2. We should start by ensuring that you understand the difference between a digital signal and an analogue signal. An analogue signal Voltage (V) Max This is a signal that can have any value between the zero and maximum of the power supply. Changes between values can occur slowly or rapidly depending on the system involved.
    [Show full text]
  • Designing Combinational Logic Gates in Cmos
    CHAPTER 6 DESIGNING COMBINATIONAL LOGIC GATES IN CMOS In-depth discussion of logic families in CMOS—static and dynamic, pass-transistor, nonra- tioed and ratioed logic n Optimizing a logic gate for area, speed, energy, or robustness n Low-power and high-performance circuit-design techniques 6.1 Introduction 6.3.2 Speed and Power Dissipation of Dynamic Logic 6.2 Static CMOS Design 6.3.3 Issues in Dynamic Design 6.2.1 Complementary CMOS 6.3.4 Cascading Dynamic Gates 6.5 Leakage in Low Voltage Systems 6.2.2 Ratioed Logic 6.4 Perspective: How to Choose a Logic Style 6.2.3 Pass-Transistor Logic 6.6 Summary 6.3 Dynamic CMOS Design 6.7 To Probe Further 6.3.1 Dynamic Logic: Basic Principles 6.8 Exercises and Design Problems 197 198 DESIGNING COMBINATIONAL LOGIC GATES IN CMOS Chapter 6 6.1Introduction The design considerations for a simple inverter circuit were presented in the previous chapter. In this chapter, the design of the inverter will be extended to address the synthesis of arbitrary digital gates such as NOR, NAND and XOR. The focus will be on combina- tional logic (or non-regenerative) circuits that have the property that at any point in time, the output of the circuit is related to its current input signals by some Boolean expression (assuming that the transients through the logic gates have settled). No intentional connec- tion between outputs and inputs is present. In another class of circuits, known as sequential or regenerative circuits —to be dis- cussed in a later chapter—, the output is not only a function of the current input data, but also of previous values of the input signals (Figure 6.1).
    [Show full text]
  • Class 10: CMOS Gate Design
    Class 10: CMOS Gate Design Topics: 1. Exclusive OR Implementation 2. Exclusive OR Carry Circuit 3. PMOS Carry Circuit Equivalent 4. CMOS Full-Adder 5. NAND, NOR Gate Considerations 6. Logic Example 7. Logic Negation 8. Mapping Logic ‘0’ 9. Equivalent Circuits 10. Fan-In and Fan-Out 11. Rise Delay Time 12. Rise Delay Time 13. Rise Delay Time 14. Fall Delay Time 15. Equal Delays Joseph A. Elias, PhD 1 Class 10: CMOS Gate Design Exclusive OR Design (Martin c4.5) 3-input XOR Truth Table Similar to how one derives a 2-input XOR (Martin, p.183) using (a’+b’)=(ab)’ (a’b’)=(a+b)’ a XOR b = a’b + ab’ = a’a + a’b + ab’ + bb’ = a’(a+b) + b’(a+b) = (a’+b’)(a+b) = (ab)’(a+b) = (ab + (a’b’) )’ = (ab + (a + b)’ )’ Joseph A. Elias, PhD 2 Class 10: CMOS Gate Design Exclusive OR Carry Circuit (Martin c4.5) NMOS realization PMOS equivalent •A in parallel with B •A in series with B •A||B in series with C •AB in parallel with C •AB in parallel with (A||B)C •A||B in series with (AB)||C Vout = Joseph A. Elias, PhD 3 Class 10: CMOS Gate Design PMOS Carry Circuit Equivalent (Martin c4.5) •Martin indicates equivalency between these circuits •Is this true? (AB+C)(A+B) = (A+B)C + (AB) ABA + ABB + AC + BC = AC +BC +AB AB + AB + AC + BC = AC + BC + AB AB + AC + BC = AB + AC + BC equivalent Joseph A. Elias, PhD 4 Class 10: CMOS Gate Design CMOS Full-Adder (Martin c4.5) Sum: (A+B+C) Carry + ABC Carry: (A+B)C + AB Joseph A.
    [Show full text]
  • –Not –And –Or –Xor –Nand –Nor
    Gates Six types of gates –NOT –AND –OR –XOR –NAND –NOR 1 NOT Gate A NOT gate accepts one input signal (0 or 1) and returns the complementary (opposite) signal as output 2 AND Gate An AND gate accepts two input signals If both are 1, the output is 1; otherwise, the output is 0 3 OR Gate An OR gate accepts two input signals If both are 0, the output is 0; otherwise, the output is 1 4 XOR Gate An XOR gate accepts two input signals If both are the same, the output is 0; otherwise, the output is 1 5 XOR Gate Note the difference between the XOR gate and the OR gate; they differ only in one input situation When both input signals are 1, the OR gate produces a 1 and the XOR produces a 0 XOR is called the exclusive OR because its output is 1 if (and only if): • either one input or the other is 1, • excluding the case that they both are 6 NAND Gate The NAND (“NOT of AND”) gate accepts two input signals If both are 1, the output is 0; otherwise, the output is 1 NOR Gate The NOR (“NOT of OR”) gate accepts two inputs If both are 0, the output is 1; otherwise, the output is 0 8 AND OR XOR NAND NOR 9 Review of Gate Processing Gate Behavior NOT Inverts its single input AND Produces 1 if all input values are 1 OR Produces 0 if all input values are 0 XOR Produces 0 if both input values are the same NAND Produces 0 if all input values are 1 NOR Produces 1 if all input values are 0 10 Combinational Circuits Gates are combined into circuits by using the output of one gate as the input for another This same circuit using a Boolean expression is AB + AC 11 Combinational Circuits Three inputs require eight rows to describe all possible input combinations 12 Combinational Circuits Consider the following Boolean expression A(B + C) Does this truth table look familiar? Compare it with previous table 13.
    [Show full text]
  • Logic Gate - Wikipedia, the Free Encyclopedia 10-3-13 下午8:30
    Logic gate - Wikipedia, the free encyclopedia 10-3-13 下午8:30 Logic gate From Wikipedia, the free encyclopedia A logic gate performs a logical operation on one or more logic inputs and produces a single logic output. The logic normally performed is Boolean logic and is most commonly found in digital circuits. Logic gates are primarily implemented electronically using diodes or transistors, but can also be constructed using electromagnetic relays (relay logic), fluidic logic, pneumatic logic, optics, molecules, or even mechanical elements. In electronic logic, a logic level is represented by a voltage or current, (which depends on the type of electronic logic in use). Each logic gate requires power so that it can source and sink currents to achieve the correct output voltage. In logic circuit diagrams the power is not shown, but in a full electronic schematic, power connections are required. Contents 1 Truth table 2 Background 3 Logic gates 4 Symbols 5 De Morgan equivalent symbols 6 Storage of bits 7 Three-state logic gates 8 Miscellaneous 9 History and development 10 Implementations 11 See also 12 References 13 Further reading 14 External links Truth table Main article: Truth table A truth table is a table that describes the behaviour of a logic gate. It lists the value of the output for every possible combination of the inputs and can be used to simplify the number of logic gates and level of nesting in an electronic circuit. In general the truth table does not lead to an efficient implementation; a minimization procedure, using Karnaugh maps, the Quine–McCluskey algorithm or an heuristic algorithm is required for reducing the circuit complexity.
    [Show full text]