sign in sign up
<<
Home , Dot crawl

20-Series High Resolution Color Monitors TM20-20RH/RP, TM14-20RH/RP 20-Series Color Monitors

The 20-Series color monitors are Auto Setup broadcast !In-line gun CRT with fine dot pitch shadow mask. monitors designed to meet today’s demanding professional needs with state-of-the-art digital !Auto setup module are standard. technology. With optional plug-in decoder borads, the 20-Series !Beam Feedback System (BFS) will accept different TV standards (NTSC, PAL-B, SECAM, PAL-M, D1, D2, D3) which can be selected !Infrared Remote Controller (Option) (NTSC, PAL-B, SECAM, PAL-M: automatically selected) !Optional adaptive comb filter

!BLUE GUN ON/OFF !RGB BACKGROUND Features !H. PHASE !HUE High Performance Cathode Ray Tube !GB GAIN !HEIGHT !Fine Dot Pitch Shadow Mask results in high resolution. Dot trio pitch !CHROMA !SYNC INT/EXT 0.31mm for TM14-20RH/RP and 0.43mm for TM20-20RH/RP. !WIDTH !CONTRAST !In-line Self Converging Electron Gun assures convergence stability. !H. CENT !BRIGHTNESS !Controlled Phosphors to ABS or EBU Standards provide consistent and !V. CENT known colorimetry. !Black Matrix surrounding Phosphor Dots assures high contrast under Beam Feedback System(BFS) bright ambient lighting. To insure long-term stability, the 20-series monitor incorporates !13V and 19V units available. Beam Feedback System(BFS) which detects CRT cathode current deviation and Digital Control System (DCS) eliminates brightness changes due to changes in CRT emission. The preset control system is completely digitized with the 8 bit MPU and the 10 bit D/A converter. It enables several status indications, and auto Adaptive Comb Decoder* setup capability with an optional PROBE (ASP-15C). Since a rotary By incorporating a CCD 1H delayline into the standard comb filter, cross encoder for preset controls and variable resistors for manual controls luminance and cross color are improved over conventional monitors. In (CONTRAST,, BRIGHTNESS, CHROMA, HUE) are provided, the 20- addition, by replacing it with an optional Adaptive Comb Filter Decoder* series monitors can be adjusted in the same manner as conventional (NTSC only), performances of 20-Series are significantly improved for analog-controlled monitors. precision color monitoring or graphics display. Auto Setup System Improvements include: By using an optional Auto Setup Prove (ASP-15C), the following !Chroma edges are greatly improved by patented process based on use of functions can be automatically setup at a reference level or stored in less luminance transitions. than 50 seconds. !Dot crawl at chroma transitions is eliminated. !CONTRAST !CHROMA !RGB BACKGROUND (* Under license from Faroudja laboratories) !BRIGHTNESS !HUE(NTSC) !GB GAIN Remote Control Operation Wide Range of Input Capabilities An infrared remote controller (RCT-20) is provided as an option. With The 20-Series can accept 3 inputs and an RGB or a component each of them, the following functions can be remotely controlled for up (Y, R-Y, B-Y) input as standard. Optional plug-in decoder boards are available to 99 monitors. for Digital (D1, D2, D3), PAL-B, SECAM, PAL-M TV standard systems. !DEGAUSS !DEALY SELECT !VIDEO SELECT !APERTURE ON/OFF Modular Concept !COLOR/MONO !RED GUN ON/OFF The 20-Series provides modular construction for ease of repair and adjustment. !WIDE/NORMAL/UNDERSCAN The boards of video system are plug-in, and many of the boards can be removed !GREEN GUN ON/OFF !MENU with the monitor mounted in a rack. !SAFE TITLE !Brightness/Contrast Specifications *Preset Contrast Input Voltage 100~120, 200~240VAC+/-10%(Auto select)50/60Hz 35Ft-L at factory setting(100% window signal) Input Power 160W *Max brightness Standard Accessory Remote connector, Power cable,Operation Manual TM14-20RH/RP:More than 70Ft-L w/window signal Input Facilities TM20-20RH/RP:More than 70Ft-L w/window signal !Input Signals *Encoded video !Resolution (at 35Ft-L) NTSC or PAL-B or PAL/SECAM or PAL-M 3ch TM14-20RH/RP: 700TV Lines (at center) TM20/14-20RH….. NTSC Decoder standard TM20-20RH/RP: 700TV Lines (at center) TM20/14-20RP….. PAL Decoder standard Output Facilities (option) Other decoders are options. Y0.7Vp-p (*Two of them can be installed simultaneously R-Y 0.525Vp-p -two slots construction) B-Y 0.525Vp-p *R/G/B or Y,R-Y,B-Y (100/0/75/0 Color bar) (MII or BETA switchable internally) 1ch Video Signal System *D1(4:2:2), D2(D3) –Option !RGB Response 50 ~ 10MHz +1, -3dB PARALLEL input 1ch !Luminance SERIAL input 2ch *Frequency Response SERIAL output 1ch(monitor OUT) w/o Notch: +/-1dB at 50Hz to 7MHz *Y/C (option) 1ch w/Notch: -30dB at 3.58MHz !Input Level *Encoded Video w/comb: +/-1dB at 50Hz tttto 7MHz Composite 1Vp-p Non Composite 0.7Vp-p (w/o Notch) (w/Notch) (w/Comb) *RGB 0.7Vp-p Non Composite *2T pulse <+/-1% <+/-2% <+/-1% Sync on Green to base line No Sync on Red + Blue or *2T pulse <+/-1% <+/-2% <+/-1% Sync Red Green Blue or External Sync to Bar *Analog Component (Y, R-Y, B-Y) *T step <1% <1% <1% MII Y signal White level 700mVp-p *Distortion <1% <1% <1% (N10) Setup level 0mVp-p *Square <1% <1% <1% (SMPTE) Sync level 300mVp-p wave response R-Y signal p-p level 525mVp-p B-Y signal p-p level 525mVp-p !Linearity less than 2% (100/0/75/0 Color bar) !Black level varies: less than 1% (APL 10% ~ 90%) Beta Y signal White level 714mVp-p !Color temperature stabilities: less than 1% for 500hours, Setup level 53.6mVp-p +10’C ~ +40’C Sync level 286mVp-p !Aperature correction R-Y signal p-p level 700mVp-p *Correction characteristics B-Y signal p-p level 700mVp-p Waveform of overshoot of 2T pulse appears (100/7.5/75/7.5 Color bar) symmetrically with TRAP ON. *Y/C Y signal 1Vp-p *Frequency response C signal 0.286Vp-p (burst level) 60Hz to 100KHz: less than +/-1dB !Connection Bridging BNC connectors, high impedance, 1MHz: less than +2dB isolated from chassis ground. 2.5MHz less than +6dB !Return loss Less than 46dB (up to 10MHz) 3.58MHz(NTSC): less than –15dB !Crosstalk between adjacent channel 4.43MHz(PAL): less than –15dB Less than 50dB (up to 6MHz) ! (at each RGB in active scan period) !Hum suppression 60dB with 4V RMS common mode rejection Coherent Noise less than –46dB !Remote control (via 10 pin connector) Hum Noise less than –55dB Video input selector (A/B/C) Other less than –55dB AUX (RGB, Y/R-Y/B-Y) Sync (COLOR/MONO) Tally (ON/OFF) Display Device In-line gun, shadow mask high resolution CRT TM14-20RH/RP: 0.31mm TM20-20RH/RP: 0.43mm !Chromaticity *ASP standard X Y R 0.630 0.340 G 0.310 0.595 B 0.155 0.070 *EBU standard X Y R 0.640 0.330 G 0.290 0.600 B 0.150 0.060 *Tolerance +/-0.005 20-Series Color Monitors

Video A/B Split (reference & variable vertical position) Specifications Color/Mono Split (reference & variable vertical position) Color Signal System w/COMB w/TRAP Beam Feedback System Suppression in >24dB >30dB Menu Assist *Contrast, Brightness, Chroma, Hue, G. Gain, Luminance at 4.43 or 3.58MHz at 4.43 or 3.58MHz B. Gain, R.BLG, G.BLG, B.BLG, Aperture Level, Luminance Suppression in >20dB ------Height, Width, V.Cent, H.Cent, Rotation, F.Focus, Chrominance at 4.43 or 3.58MHz at 4.43 or 3.58MHz H.Phase Chroma/ Delay <20nsec. <20nsec. *Safe Title Setup *Split Setup Chroma Signal Response *System Setup NTSC 2.3MHz to 4.9MHz: +1, -3dB Decoder Select (NTSC/PAL-B/PAL-M/SECAM) (reference 3.58MHz) Test Signal ON/OFF PAL-B 3.1MHz to 5.7MHz: +1, -3dB *Mode Setup (reference 4.43MHz) User Display ON/OFF Demodulator Axis Aux RGB/Y,R-Y,B-Y R-Y VS B-Y 90 degree CH C / Y/C Oscillator Performance Level Display ON/OFF Subcarrier Lock-in Control Lock Setup +/-200Hz (NTSC/PAL-M) Front Control +/-300Hz (PAL-B) Outside of Drawer *Power ON/OFF Phase Error Less than 2 degree for each of following individual *Degauss ON conditions: *Color/Mono a)Burst frequency: +/-10Hz *Sync INT/EXT b)Burst level change: +6dB, -12dB *Video Select (A/B/C/Aux/Digital/Test/A-B split) c)Ambient temperature change by +10’C *Delay (H Delay, V Delay, HV Delay) d)Sync-blanking within FCC requirement *Scan (UNDER. Normal, OVER) Color Killer Automatic operation when burst level is less than 5 *Aperture ON/OFF +/-1 IRE. *Screens (R/G/B ON/OFF) Adjustments *Chroma amplitude: +/-6dB *Safe Title ON/OFF *Subcarrier phase: +/-15 degree *Contrast, Brightness, Chroma, Hue Preset/Manual Raster + Deflection Inside of Drawer *Setup ON/OFF Scan *Normal scan *AUTO/FORCED COLOR Aspect ratio 4:3 with blanked raster 1% *AFC Normal/Fast/Slow *Under scan *Residual Subcarrier Aspect ratio 4:3 approx. –7.5% *File Control (adjustable 90% of normal scan) *Rotary Encoder *Over scan *Preset Change 105% of normal scan Contrast, Brightness, Chroma, Hue, Stability of Raster Size RGB Background, GB Gain,, Rotation, 1% of picture height 0 ~ 100% APL at 35Ft-L Aperture Level, Fine Focus, Height, reference Width, H Center, V Center, H Phase Linearity H + V line Dimensions TM14-20RH/RP: 0.5% of picture height 450(W) x 265(H) x 515(D) mm Geometry Entire Screen 17.72(W) x 10.43(H) x 20.28(D) inches 0.5% of picture center TM20-20RH/RP: AFC Time Constant 450(W) x 399(H) x 515(D) mm Normal: 2msec 17.72(W) x 15.71(H) x 20.28(D) inches Fast: 0.5msec Weight TM14-20RH/RP: 26kg (57.3 lbs) approx. Slow: 7msec TM20-20RH/RP: 38kg (83.8 lbs) approx. Retrace Time Horizontal: 0.9usec. Vertical: 0.8msec. High Voltage *Tolerance: TM14-20RH/RP 25kV+/-0.5kV TM20-20RH/RP 25kV+/-0.5kV *Regulation: within +/-1% at 0 to 450uA Convergence Center: <0.3mm(within circle of 80% of picture height) Corners: <0.5mm(outside area of picture center) Functions Adaptive Comb Decoder (option) Safe Title Generator (100,95,90,85,80%, 100+90+80%, 5 CROSS HATCH, 10 CROSS HATCH selectable) Auto Setup (with an optional probe) Infrared Remote Control (with an optional remote control box) Test Signals *Cross Hatch, * Flat Field(50%), *Window (100%), *10step stair signal with plugs as standard, Design and specifications are subject to change without notice. *Character