SDS Contains All of the Information Required by the CPR

Total Page:16

File Type:pdf, Size:1020Kb

SDS Contains All of the Information Required by the CPR SAFETY DATA SHEET Preparation Date: 08/25/2015 Revision Date: 08/25/2015 Revision Number: G1 1. IDENTIFICATION Product identifier Product code: S1666 Product Name: SODIUM AZIDE, REAGENT, ACS Other means of identification Synonyms: Azide Azium Sodium salt of hydrazoic acid CAS #: 26628-22-8 RTECS # VY8050000 CI#: Not available Recommended use of the chemical and restrictions on use Recommended use: Laboratory reagent. Preservative in diagnosis medicines and blood tests; propellant used for inflating automobile air bags. Herbicide. Fungicide. Soil fumigant. Uses advised against No information available Supplier: Spectrum Chemical Mfg. Corp 14422 South San Pedro St. Gardena, CA 90248 (310) 516-8000 Order Online At: https://www.spectrumchemical.com Emergency telephone number Chemtrec 1-800-424-9300 Contact Person: Martin LaBenz (West Coast) Contact Person: Ibad Tirmiz (East Coast) 2. HAZARDS IDENTIFICATION Classification This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200) Acute toxicity - Oral Category 2 Acute toxicity - Dermal Category 1 Acute toxicity - Inhalation (Dusts/Mists) Category 1 Serious eye damage/eye irritation Category 2A Specific target organ toxicity (single exposure) Category 2 Explosives Division 1.4 Label elements Product code: S1666 Product name: SODIUM AZIDE, 1 / 14 REAGENT, ACS Danger Hazard statements Fatal if swallowed Fatal in contact with skin Fatal if inhaled Causes serious eye irritation May cause damage to organs Fire or projection hazard Hazards not otherwise classified (HNOC) Not Applicable Other hazards Contact with acid liberates poisonous gas Reacts violently with water Precautionary Statements - Prevention Keep away from heat/sparks/open flames/hot surfaces. — No smoking Ground/bond container and receiving equipment Do not subject to grinding/shock/ .? /friction Do not eat, drink or smoke when using this product Wear respiratory protection Wear protective gloves/protective clothing/eye protection/face protection Do not get in eyes, on skin, or on clothing Do not breathe dust/fume/gas/mist/vapors/spray Use only outdoors or in a well-ventilated area Wash face, hands and any exposed skin thoroughly after handling Precautionary Statements - Response Specific treatment (see .? on this label) Specific measures (see .? on this label) Specific treatment is urgent (see .? on this label) IF exposed or if you feel unwell: Call a POISON CENTER or doctor/physician In case of fire: Evacuate area. DO NOT fight fire when fire reaches explosives. Fight fire with normal precautions from a reasonable distance. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. Product code: S1666 Product name: SODIUM AZIDE, 2 / 14 REAGENT, ACS Immediately call a POISON CENTER or doctor/physician IF ON SKIN: Gently wash with plenty of soap and water Remove/Take off immediately all contaminated clothing Wash contaminated clothing before reuse IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing. Immediately call a POISON CENTER or doctor/physician. IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician Rinse mouth Precautionary Statements - Storage Store locked up Store in a well-ventilated place. Keep container tightly closed Store in accordance with local regulations Precautionary Statements - Disposal Dispose of contents/container to an approved waste disposal plant 3. COMPOSITION/INFORMATION ON INGREDIENTS Components CAS-No. Weight % Trade Secret Sodium Azide 26628-22-8 100 * 26628-22-8 4. FIRST AID MEASURES First aid measures General Advice: Poison information centers in each State capital city can provide additional assistance for scheduled poisons (13 1126). Ensure that medical personnel are aware of the material(s) involved and take precautions to protect themselves. Skin Contact: Wash off immediately with soap and plenty of water. Continue flushing with plenty of water for at least 15 minutes. Remove and wash contaminated clothing before re-use. Immediate medical attention is required. Call a physician or Poison Control Centre immediately. Eye Contact: Flush eye with water for 15 minutes. Immediate medical attention is required. Call a physician or Poison Control Centre immediately. Inhalation: Move to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. WARNING! It may be hazardous to the person providing aid to give mouth-to-mouth resuscitation when the inhaled or ingested material is toxic, infectious or corrosive. Do not use mouth-to-mouth resuscitation if victim ingested or inhaled the substance; induce artificial respiration with the aid of a pocket mask equipped with a one-way valve or other proper respiratory medical device. Immediate medical attention is required. Ingestion: Fatal if swallowed. Do not induce vomiting without medical advice. Never give anything by mouth to an unconscious person. Immediate medical attention is required. Call a physician or Poison Control Center immediately. Most important symptoms and effects, both acute and delayed Symptoms Fatal if swallowed, in contact with skin or if inhaled. Causes serious eye irritation. May cause damage to organs. May cause headache. Coughing. May cause bronchitis. May cause abdominal pain, nausea, vomiting, diarrhea. May cause hypermotility, diarrhea. May cause anorexia. May affect behavior/central nervous system. Severe over-exposure can result in death. Indication of any immediate medical attention and special treatment needed Notes to Physician: Treat symptomatically Product code: S1666 Product name: SODIUM AZIDE, 3 / 14 REAGENT, ACS Protection of first-aiders First-Aid Providers: Avoid exposure to blood or body fluids. Wear gloves and other necessary protective clothing. Dispose of contaminated clothing and equipment as bio-hazardous waste 5. FIRE-FIGHTING MEASURES Extinguishing Media Suitable Extinguishing Media: Dry chemical. Carbon dioxide (CO2). Dry sand. Unsuitable Extinguishing Media: Water. Specific hazards arising from the chemical Hazardous Combustion Products: Nitrogen oxides. Sodium oxides Specific hazards: Combustible material It may burn, but does not readily ignite Not considered flammable unless heated above300 deg. C. When heated to decomposition it emits very toxic fumes of nitrogen oxides and disodium oxide. Containers may explode when heated Special Protective Actions for Firefighters Specific Methods: Water mist may be used to cool closed containers. Do not get water inside containers. Special Protective Equipment for Firefighters: As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full protective gear 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Personal Precautions: Ensure adequate ventilation. Keep people away from and upwind of spill/leak. Use personal protective equipment. Avoid contact with skin, eyes and clothing. Evacuate personnel to safe areas. Avoid breathing dust. Avoid dust formation. Do not get water inside containers. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Remove all sources of ignition. All equipment used when handling the product must be grounded. Use spark-proof tools and explosion-proof equipment. Take precautionary measures against static discharges. Environmental precautions Prevent further leakage or spillage if safe to do so. Do not let product enter drains. Prevent entry into waterways, sewers, basements or confined areas. Methods and material for containment and cleaning up Methods for containment Stop leak if you can do it without risk. Cover with plastic sheet to prevent spreading. Methods for cleaning up Use appropriate tools to put the spilled solid in a suitable waste disposal container. Use only non-sparking tools. Clean contaminated surface thoroughly. 7. HANDLING AND STORAGE Precautions for safe handling Technical Measures/Precautions: Provide sufficient air exchange and/or exhaust in work rooms. All equipment used when handling the product must be grounded. Avoid dust formation. Remove all sources of ignition. Keep away from incompatible materials. Product code: S1666 Product name: SODIUM AZIDE, 4 / 14 REAGENT, ACS Safe Handling Advice Wear personal protective equipment. Avoid contact with skin, eyes and clothing. Avoid dust formation. Avoid shock and friction. Do not breathe vapours/dust. Do not ingest. Do not smoke. Keep away from heat and sources of ignition. Handle in accordance with good industrial hygiene and safety practice. Never add water to this product. Use explosion-proof equipment. Conditions for safe storage, including any incompatibilities Technical Measures/Storage Conditions: Keep container tightly closed in a dry and well-ventilated place. Keep away from heat and sources of ignition. Store away from incompatible materials. Store in a segrated and approved area. Incompatible Materials: Acids. Metals. Water. Incompatible with Barium carbonate, Trifluoroacryloyl fluoride, carbon disulfide, nitrogen- diluted bromine vapor, with metals such as brass, lead, silver, mercury, and copper, Chromyl chloride, Dimethyl sulfate, Dibromomalononitrile, Sulfuric acid, ammonium chloride + trichloroacetonitrile, Phosgene, Cyanuric chloride, 2,5-Dinitro-3-methylbenzoic acid + Oleum. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Control parameters
Recommended publications
  • Chemical Chemical Hazard and Compatibility Information
    Chemical Chemical Hazard and Compatibility Information Acetic Acid HAZARDS & STORAGE: Corrosive and combustible liquid. Serious health hazard. Reacts with oxidizing and alkali materials. Keep above freezing point (62 degrees F) to avoid rupture of carboys and glass containers.. INCOMPATIBILITIES: 2-amino-ethanol, Acetaldehyde, Acetic anhydride, Acids, Alcohol, Amines, 2-Amino-ethanol, Ammonia, Ammonium nitrate, 5-Azidotetrazole, Bases, Bromine pentafluoride, Caustics (strong), Chlorosulfonic acid, Chromic Acid, Chromium trioxide, Chlorine trifluoride, Ethylene imine, Ethylene glycol, Ethylene diamine, Hydrogen cyanide, Hydrogen peroxide, Hydrogen sulfide, Hydroxyl compounds, Ketones, Nitric Acid, Oleum, Oxidizers (strong), P(OCN)3, Perchloric acid, Permanganates, Peroxides, Phenols, Phosphorus isocyanate, Phosphorus trichloride, Potassium hydroxide, Potassium permanganate, Potassium-tert-butoxide, Sodium hydroxide, Sodium peroxide, Sulfuric acid, n-Xylene. Acetone HAZARDS & STORAGE: Store in a cool, dry, well ventilated place. INCOMPATIBILITIES: Acids, Bromine trifluoride, Bromine, Bromoform, Carbon, Chloroform, Chromium oxide, Chromium trioxide, Chromyl chloride, Dioxygen difluoride, Fluorine oxide, Hydrogen peroxide, 2-Methyl-1,2-butadiene, NaOBr, Nitric acid, Nitrosyl chloride, Nitrosyl perchlorate, Nitryl perchlorate, NOCl, Oxidizing materials, Permonosulfuric acid, Peroxomonosulfuric acid, Potassium-tert-butoxide, Sulfur dichloride, Sulfuric acid, thio-Diglycol, Thiotrithiazyl perchlorate, Trichloromelamine, 2,4,6-Trichloro-1,3,5-triazine
    [Show full text]
  • Potentially Explosive Chemicals*
    Potentially Explosive Chemicals* Chemical Name CAS # Not 1,1’-Diazoaminonaphthalene Assigned 1,1-Dinitroethane 000600-40-8 1,2,4-Butanetriol trinitrate 006659-60-5 1,2-Diazidoethane 000629-13-0 1,3,5-trimethyl-2,4,6-trinitrobenzene 000602-96-0 1,3-Diazopropane 005239-06-5 Not 1,3-Dinitro-4,5-dinitrosobenzene Assigned Not 1,3-dinitro-5,5-dimethyl hydantoin Assigned Not 1,4-Dinitro-1,1,4,4-tetramethylolbutanetetranitrate Assigned Not 1,7-Octadiene-3,5-Diyne-1,8-Dimethoxy-9-Octadecynoic acid Assigned 1,8 –dihydroxy 2,4,5,7-tetranitroanthraquinone 000517-92-0 Not 1,9-Dinitroxy pentamethylene-2,4,6,8-tetramine Assigned 1-Bromo-3-nitrobenzene 000585-79-5 Not 2,2',4,4',6,6'-Hexanitro-3,3'-dihydroxyazobenzene Assigned 2,2-di-(4,4,-di-tert-butylperoxycyclohexyl)propane 001705-60-8 2,2-Dinitrostilbene 006275-02-1 2,3,4,6- tetranitrophenol 000641-16-7 Not 2,3,4,6-tetranitrophenyl methyl nitramine Assigned Not 2,3,4,6-tetranitrophenyl nitramine Assigned Not 2,3,5,6- tetranitroso nitrobenzene Assigned Not 2,3,5,6- tetranitroso-1,4-dinitrobenzene Assigned 2,4,6-Trinitro-1,3,5-triazo benzene 029306-57-8 Not 2,4,6-trinitro-1,3-diazabenzene Assigned Not 2,4,6-Trinitrophenyl trimethylol methyl nitramine trinitrate Assigned Not 2,4,6-Trinitroso-3-methyl nitraminoanisole Assigned 2,4-Dinitro-1,3,5-trimethyl-benzene 000608-50-4 2,4-Dinitrophenylhydrazine 000119-26-6 2,4-Dinitroresorcinol 000519-44-8 2,5-dimethyl-2,5-diydroperoxy hexane 2-Nitro-2-methylpropanol nitrate 024884-69-3 3,5-Dinitrosalicylic acid 000609-99-4 Not 3-Azido-1,2-propylene glycol dinitrate
    [Show full text]
  • Addition Reactions and Photoisomerization of Cis,Trans-1,5-Cyclodecadiene
    Louisiana State University LSU Digital Commons LSU Historical Dissertations and Theses Graduate School 1970 Addition Reactions and Photoisomerization of Cis,trans-1,5-Cyclodecadiene. Hsin-hsiong Hsieh Louisiana State University and Agricultural & Mechanical College Follow this and additional works at: https://digitalcommons.lsu.edu/gradschool_disstheses Recommended Citation Hsieh, Hsin-hsiong, "Addition Reactions and Photoisomerization of Cis,trans-1,5-Cyclodecadiene." (1970). LSU Historical Dissertations and Theses. 1859. https://digitalcommons.lsu.edu/gradschool_disstheses/1859 This Dissertation is brought to you for free and open access by the Graduate School at LSU Digital Commons. It has been accepted for inclusion in LSU Historical Dissertations and Theses by an authorized administrator of LSU Digital Commons. For more information, please contact [email protected]. 71-6579 HSIEH, Hsin-Hsiong, 1936- ADDITION REACTIONS AND PHOTOISOMERIZATION OF CIS,TRANS-1,5-CYCLODECADIENE. The Louisiana State University and Agricultural and Mechanical College, Ph.D., 1970 Chemistry, organic University Microfilms, Inc., Ann Arbor, Michigan ADDITION REACTIONS AND PHOTOISOMERIZATION OF CIS,TRANS-1,5“CYCLODECADIENE A Dissertation Submitted to the Graduate Faculty of the Louisiana State University and Agricultural and Mechanical College in partial fulfillment of the requirements for the degree of Doctor of Philosophy in The Department of Chemistry by Hsin-Hsiong Hsieh B.S., Taiwan Provincial Chung-Hsing University, i960 M.S., Louisiana State University,
    [Show full text]
  • Chemical Names and CAS Numbers Final
    Chemical Abstract Chemical Formula Chemical Name Service (CAS) Number C3H8O 1‐propanol C4H7BrO2 2‐bromobutyric acid 80‐58‐0 GeH3COOH 2‐germaacetic acid C4H10 2‐methylpropane 75‐28‐5 C3H8O 2‐propanol 67‐63‐0 C6H10O3 4‐acetylbutyric acid 448671 C4H7BrO2 4‐bromobutyric acid 2623‐87‐2 CH3CHO acetaldehyde CH3CONH2 acetamide C8H9NO2 acetaminophen 103‐90‐2 − C2H3O2 acetate ion − CH3COO acetate ion C2H4O2 acetic acid 64‐19‐7 CH3COOH acetic acid (CH3)2CO acetone CH3COCl acetyl chloride C2H2 acetylene 74‐86‐2 HCCH acetylene C9H8O4 acetylsalicylic acid 50‐78‐2 H2C(CH)CN acrylonitrile C3H7NO2 Ala C3H7NO2 alanine 56‐41‐7 NaAlSi3O3 albite AlSb aluminium antimonide 25152‐52‐7 AlAs aluminium arsenide 22831‐42‐1 AlBO2 aluminium borate 61279‐70‐7 AlBO aluminium boron oxide 12041‐48‐4 AlBr3 aluminium bromide 7727‐15‐3 AlBr3•6H2O aluminium bromide hexahydrate 2149397 AlCl4Cs aluminium caesium tetrachloride 17992‐03‐9 AlCl3 aluminium chloride (anhydrous) 7446‐70‐0 AlCl3•6H2O aluminium chloride hexahydrate 7784‐13‐6 AlClO aluminium chloride oxide 13596‐11‐7 AlB2 aluminium diboride 12041‐50‐8 AlF2 aluminium difluoride 13569‐23‐8 AlF2O aluminium difluoride oxide 38344‐66‐0 AlB12 aluminium dodecaboride 12041‐54‐2 Al2F6 aluminium fluoride 17949‐86‐9 AlF3 aluminium fluoride 7784‐18‐1 Al(CHO2)3 aluminium formate 7360‐53‐4 1 of 75 Chemical Abstract Chemical Formula Chemical Name Service (CAS) Number Al(OH)3 aluminium hydroxide 21645‐51‐2 Al2I6 aluminium iodide 18898‐35‐6 AlI3 aluminium iodide 7784‐23‐8 AlBr aluminium monobromide 22359‐97‐3 AlCl aluminium monochloride
    [Show full text]
  • CHEM Safety Manual
    Department of Chemistry Safety Manual October 2018 Safety Committee Department of Chemistry Hong Kong University of Science and Technology Table of Contents 1.0 Introduction 2.0 Safety Policy and Responsibility for Safety 2.1 Department Head 2.2 Department of Chemistry Safety Committee 2.3 Laboratory Supervisors 2.4 Researchers 2.5 HSEO 3.0 Information, Training, Safety Clearance, and Safety Clearance at Termination 3.1 Initial Training 3.2 Information on Hazardous Substances 3.3 Additional Safety Information 3.4 Safety Clearance at Termination 4.0 Personal Protective Equipment and Safety Engineering Controls 4.1 Eye Protection 4.2 Protective Apparel 4.3 Respirators 4.4 Laboratory Fume Cupboards 4.5 Fire Extinguishers, Safety Showers, and Eyewash Facilities 5.0 Standard Operating Procedures for Work with Hazardous Substances 5.1 Classes of Hazardous Substances 5.2 General Procedures for Work with Toxic Substances 5.3 General Procedures for Work with Flammable and Explosive Substances 6.0 Procedures for Work with Particularly Hazardous Substances 6.1 Identification and Classification of Particularly Hazardous Substances 6.2 Designated Areas 6.3 General Procedures for Work with Substances of Moderate to High Chronic or High Acute Toxicity 6.4 Additional Procedures for Work with Substances of Known High Chronic Toxicity 6.5 Specific Handling Procedures for Some Common Particularly Hazardous Substances 7.0 Proper Planning of Laboratory Work 7.1 Recognition and Assessment 7.2 Planning for the Unexpected: What Could Go Wrong? 7.3 Site Selection
    [Show full text]
  • Linee Guida Operative Per La Corretta Gestione Dei Rifiuti Speciali EN
    OPERATIONAL GUIDELINES FOR THE MANAGEMENT OF SPECIAL HAZARDOUS WASTE October 2019 OPERATIONAL GUIDELINES FOR THE MANAGEMENT OF SPECIAL HAZARDOUS WASTE This document describes the types of waste produced by the Unicam teachinG and research acHviHes, the methods of collecHon and management, the procedures for the delivery of special hazardous and sanitary waste, infecHous and non-infecHous, to Temporary Waste Storage. AIMS The purpose of the followinG Guidelines is to provide instrucHons on conduct, to ensure that: • All the waste produced is not dispersed in the environment; • The current leGislaHon on waste is respected; • The waste management methods are homoGeneous in all Unicam structures; • The waste is transferred in a substanHally and formally correct way to the Temporary Waste Storage present in every facility in which special hazardous waste is produced, in order to protect the health of employees, with respect for the environment and compliance with the current leGislaHon. SCOPE OF APPLICATION These Guidelines reGulate the management of hazardous waste, medical waste, waste consisHnG of recyclable substances, packaginG and packaginG waste, not includinG: • radioacHve waste, as it is beinG reGulated by specific leGislaHon; • liquids free of danGerous chemical and / or bioloGical substances, introduced into the sewer system; • management of special waste derivinG from intervenHons on the technoloGical systems present in the University buildinGs and areas, since it is the responsibility of the company in charGe of runninG and managinG those systems, as well as carryinG out ordinary maintenance and extraordinary maintenance. COMPLIANCE All University staff, includinG students and their equivalents, are required to comply with and apply the provisions of the followinG Guidelines.
    [Show full text]
  • Safety Data Sheet Valve Regulated Lead Acid Battery, Non-Spillable
    SAFETY DATA SHEET VALVE REGULATED LEAD ACID BATTERY, NON-SPILLABLE SECTION 1: PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: NON-SPILLABLE Battery OTHER PRODUCT Valve Regulated Lead Acid Battery (gel/absorbed electrolyte), Electric Storage Battery NAMES: Battery Non-Spillable 49 CFR 173.159a MANUFACTURER: East Penn Manufacturing Company ADDRESS: Deka Road Lyon Station, PA 19536 USA EMERGENCY TELEPHONE NUMBERS: US/CN: CHEMTREC 1-800-424-9300 Outside US/CN: CHEMTREC 1-703-527-3887 NON-EMERGENCY HEALTH/SAFETY INFORMATION: 610-682-6361 CHEMICAL FAMILY: This product is a gel/absorbed electrolyte type lead acid storage battery. PRODUCT USE: Consumer/Industrial/Commercial electrical storage batteries. SECTION 2: HAZARDS IDENTIFICATION GHS Classification: Health Environmental Physical Acute Toxicity – Category 4 Aquatic Chronic – 1 Explosive Chemical, Division 1.3 Skin Corrosion – Category 1A Aquatic Acute – 1 Eye Damage – Category 1 Reproductive – Category 1A Carcinogenicity (lead)– Category 1B Carcinogenicity (arsenic)– Category 1A Carcinogenicity(acid mist)–Category1A Specific Target Organ Toxicity (repeated exposure) –Category 2 GHS Label: Signal Word: DANGER ! PAGE 1 OF 9 East Penn Manufacturing Co. SAFETY DATA SHEET VALVE REGULATED LEAD ACID BATTERY, NON-SPILLABLE Hazard Statements Precautionary Statements Health Prevention Harmful if swallowed, inhaled, or in contact with skin. Wash thoroughly after handling. Causes severe skin burns and eye damage. Do not eat, drink or smoke when using this product. Causes serious eye damage. Wear protective gloves/protective clothing, eye protection/face May damage fertility or the unborn child if ingested or protection. inhaled. Avoid breathing dust/fume/gas/mist/vapors/spray. May cause cancer if ingested or inhaled. Use only outdoors or in a well-ventilated area.
    [Show full text]
  • AGENDA Eau Claire County • LOCAL EMERGENCY PLANNING COMMITTEE • Date: Thursday, May 13, 2021 Time: 4:00 P.M
    AGENDA Eau Claire County • LOCAL EMERGENCY PLANNING COMMITTEE • Date: Thursday, May 13, 2021 Time: 4:00 p.m. *In-Person OR Remote Access* In-Person (COVID-19 safety protocols will be in place) Washington Town Hall 5750 Old Town Hall Road Eau Claire, Wisconsin 54701 Remote Access *Event link below can be used to connect to meeting and interact (by the chair) from computer or through the WebEx Meeting smartphone app. Join WebEx Meeting: https://eauclairecounty.webex.com Meeting ID: 145 435 7828 Password: zpFXJtKD474 *Meeting audio can be listened to using this Audio conference dial in information. Audio conference: 1-415-655-0001 Access Code: 1454357828## For those wishing to make public comment, you must e-mail Sam Simmons at [email protected] at least 30 minutes prior to the start of the meeting. You will be called on during the public comment period to make your comments. *Please mute personal devices upon entry 1. Call to Order and confirmation of meeting notice 2. Public Comment (15 minute maximum) 3. Review – Approval of the February 11, 2021 Minutes / Discussion – Action PAGES 2 - 4 4. Review/Approval of Off-Site Response Plans / Discussion – Action a. AT&T PK0116 – Tabled from 02/11/2021 PAGES 5 - 25 b. AT&T PK0106 – Tabled from 02/11/2021 PAGES 26 - 48 c. Cleghorn Micro-PK9608 PAGES 49 - 50 d. Great Lakes Coca-Cola PAGES 51 - 72 e. Hutchinson Technology, Inc. PAGES 73 - 132 5. Emergency Management Overview and Updates / Discussion 6. Local Hazardous Materials Spill Response Team Report / Discussion 7.
    [Show full text]
  • BNL CHEMICAL STORAGE and COMPATIBILITY TABLE Revision Date: 07-24-07 the Only Official Copy of This Document Is On-Line at the SHSD Website
    BNL CHEMICAL STORAGE AND COMPATIBILITY TABLE Revision Date: 07-24-07 The only official copy of this document is on-line at the SHSD website. Before using a printed copy, verify that it is current by checking the document issue date on the website. http://www.bnl.gov/esh/shsd/Programs/Program_Area_Chemicals_Compatibility.asp Information contained in this table was compiled from the following sources: Academic Laboratory Chemical Hazards Guidebook by William J. Mahn, Published by Van Nostrand, Reinhold, 1991; Fire Protection Guide to Hazardous Materials 11th edition, National Fire Protection Association, 1994; Hazardtext® Hazard Managements Database; INFOTEXT® Documents Database; Better Science Through Safety by Jack A. Gerlovich and Gary E. Downs, © 1981 by the Iowa State University Press. Document Revision Date 07-24-07 Ken Erickson CHO Chemical Chemical Hazard and Compatibility Information Acetic Acid HAZARDS & STORAGE: Corrosive and combustible liquid. Serious health hazard. Reacts with oxidizing and alkali materials. Keep above freezing point (62 ºF) to avoid rupture of carboys and glass containers. INCOMPATIBILITIES: 2-amino-ethanol, Acetaldehyde, Acetic anhydride, Acids, Alcohol, Amines, 2-Amino- ethanol, Ammonia, Ammonium nitrate, 5-Azidotetrazole, Bases, Bromine pentafluoride, Caustics (strong), Chlorosulfonic acid, Chromic Acid, Chromium trioxide, Chlorine trifluoride, Ethylene imine, Ethylene glycol, Ethylene diamine, Hydrogen cyanide, Hydrogen peroxide, Hydrogen sulfide, Hydroxyl compounds, Ketones, Nitric Acid, Oleum, Oxidizers
    [Show full text]
  • Organic & Biomolecular Chemistry
    Organic & Biomolecular Chemistry Accepted Manuscript This is an Accepted Manuscript, which has been through the Royal Society of Chemistry peer review process and has been accepted for publication. Accepted Manuscripts are published online shortly after acceptance, before technical editing, formatting and proof reading. Using this free service, authors can make their results available to the community, in citable form, before we publish the edited article. We will replace this Accepted Manuscript with the edited and formatted Advance Article as soon as it is available. You can find more information about Accepted Manuscripts in the Information for Authors. Please note that technical editing may introduce minor changes to the text and/or graphics, which may alter content. The journal’s standard Terms & Conditions and the Ethical guidelines still apply. In no event shall the Royal Society of Chemistry be held responsible for any errors or omissions in this Accepted Manuscript or any consequences arising from the use of any information it contains. www.rsc.org/obc Page 1 of 5 OrganicPlease & doBiomolecular not adjust margins Chemistry Journal Name COMMUNICATION Safe generation and use of bromine azide under continuous flow conditions ̶ selective 1,2-bromoazidation of olefins Received 00th January 20xx, Accepted 00th January 20xx David Cantillo, Bernhard Gutmann and C. Oliver Kappe* Manuscript DOI: 10.1039/x0xx00000x www.rsc.org/ Bromine azide (BrN3), a useful but extremely toxic and explosive halogen azides was systematically explored by the group of reagent for the preparation of vicinal 1,2-bromine azide Hassner.4 Hassner and co-workers for the first time compounds, was safely generated and reacted in situ with alkenes demonstrated the direct addition of halogen azides to olefins in a continuous flow photoreactor.
    [Show full text]
  • Safe Generation and Use of Bromine Azide Under Continuous Flow
    Electronic Supplementary Material (ESI) for Organic & Biomolecular Chemistry. This journal is © The Royal Society of Chemistry 2015 S1 Electronic Supplementary Information Safe generation and use of bromine azide under continuous flow conditions ̶ selective 1,2- bromoazidation of olefins David Cantillo, Bernhard Gutmann, and C. Oliver Kappe* Institute of Chemistry, University of Graz, NAWI Graz, Heinrichstrasse 28, 8010 Graz (Austria) E-mail: [email protected] Contents: General Remarks ........................................................................................... S2 Experimental Procedures and Characterization Data .................................... S2-S5 Continuous Flow Setup for the 1,2-Bromo Azidations ................................. S6 Schematic View of the Continuous Photochemical Reactor ......................... S7 GC-MS and HPLC Chromatograms of crude reactions for 2a and 2b ......... S8 Mechanism of the Hemetsberger-Knittel Indolization .................................. S9-S11 NMR Spectra for all Prepared Compounds ................................................... S12-S24 S2 General remarks. 1H-NMR spectra were recorded on a Bruker 300 MHz instrument. Chemical shifts () are expressed in ppm downfield from TMS as internal standard. The letters s, d, t, q, and m are used to indicate singlet, doublet, triplet, quadruplet, and multiplet. Analytical HPLC analysis was carried out on a C18 reversed-phase (RP) analytical column (150 4.6 mm, particle size 5 mm) at 25 °C using a mobile phase A (water/acetonitrile 90:10 (v/v) + 0.1% TFA) and B (MeCN + 0.1% TFA) at a flow rate of 1.0 mL min-1. The following gradient was applied: linear increase from solution 30% B to 100% B in 8 min, hold at 100% solution B for 2 min. GC/MS (FOCUS-GC/DSQ II MS, ThermoFisher) monitoring was based on electron impact ionization (70 eV) using a HP/5MS column (30 m×0.250 mm×0.025 μm).
    [Show full text]
  • UPS Chemical Table - ICAO/IATA Version (U.S
    UPS Chemical Table - ICAO/IATA Version (U.S. Air Packages) "PASSENGER AIRCRAFT" QUANTITIES HAZARD CLASS HAZARDOUS MATERIALS DESCRIPTIONS OR DIVISION LTD QTY PASSENGER AIR CARGO AIR ▲ AND PROPER SHIPPING NAMES (Subsidiary if PACKING LABEL(S) REQUIRED OR EXEMPTION, PACKING LTD QTY PACKING PASSENGER AIR PACKING CARGO SPECIAL UNID (ALSO MARK ON PACKAGE) applicable) GROUP SPECIAL PERMIT OR EXCEPTION INSTRUCTION MAX INSTRUCTION MAX ** INSTRUCTION AIR MAX *** PROVISIONS (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) Accellerene - see p-Nitrosodimethylaniline (UN 1369) Accumulators, electric - see Batteries, etc. (UN 2794, UN 2795, UN 2800, UN 3028, UN 3292) Accumulators, pressurized, hydraulic/pneumatic (containing non-flammable gas) - see Articles, pressurized, etc. (UN 3164) UN1088 Acetal 3 II FLAMMABLE LIQUID Y341 1 L 353 5 L 364 30 L UN1089 Acetaldehyde 3 I FLAMMABLE LIQUID Forbidden Forbidden 361 30 L A1 UN1841 Acetaldehyde ammonia 9 III MISCELLANEOUS Forbidden 956 30 kg 956 30 kg UN2332 Acetaldehyde oxime 3 III FLAMMABLE LIQUID Y344 10 L 355 25 L 366 30 L CORROSIVE & UN2789 Acetic acid, glacial 8 (3) II FLAMMABLE LIQUID Y840 0.5 L 851 1 L 855 30 L CORROSIVE & UN2789 Acetic acid solution with > 80% acid, by mass 8 (3) II FLAMMABLE LIQUID Y840 0.5 L 851 1 L 855 30 L Acetic acid solution with >= 50% and <= 80% acid, by UN2790 mass 8 II CORROSIVE Y840 0.5 L 851 1 L 855 30 L Acetic acid solution with > 10% and < 50% acid, by UN2790 mass 8 III CORROSIVE Y841 1 L 852 5 L 856 30 L A803 CORROSIVE & UN1715 Acetic anhydride 8 (3) II FLAMMABLE
    [Show full text]