5-Piece Junior Drum Kit Assembly Instruction

Total Page:16

File Type:pdf, Size:1020Kb

5-Piece Junior Drum Kit Assembly Instruction 5-Piece Junior Drum Kit Assembly Instruction Thank you for choosing this quality set from Cecilio. Use the instructions as a guide to help you assemble your new drum set. Please note that this manual is designed for a number of Cecilio drum sets. If you are unsure of what your drum set should be supplied with, please check with the Cecilio dealer you purchased the kit from. There are many parts that make up a drum set, but don’t worry, once you get started the process is very intuitive and fun. Bass Drum: 1. Lay the Bass drum Shell (A) on a flat surface with the front side up. You can identify the front side by the location of the Bass Drum leg mount (B). The leg mounts are closer to the front side of the bass drum (furthest from the playing position). 2. The “logo drumhead” should be fitted to the front of the bass drum and aligned straight. 3. Place the drum head (C) (same diameter as the drum) directly on the top of the drum shell followed by the hoop (D). 4. Gently hang the claws (E) over the edge of the hoop, and line them up with the lugs. Take the longest ten- sion screws (aka T-Rods), slip a washer on each, and insert them through the holes in the claws. 5. Tighten the screws into the lugs using your fingers two at a time, just enough so the hoops are secure, and no wrinkles are in the head. 6. Now you may use a drum key (F) to tighten the tension bolts in equal amounts (1 quarter turn each for example) until pitch and tone of the drum begin to sound. The tension bolts should be tightened in a star formation the same as when you change a wheel in a car (tighten the first bolt, then opposite bolt, etc). Repeat this process on the top and bottom of bass drum. 7. Insert the drum legs (G) into the leg mounts and secure. Sit the drum upright and adjust the height so that the front of the Bass Drum is elevated 1 inch off the floor and will not pivot. Be sure that the bass drum legs are secured and even. 8. To attach the bass drum pedal (H), place the pedal base under the bass drum hoop and make sure the clamp is over the hoop. Connect the footboard to the pedal frame. Tighten the pedal clamp by the wing nut under the footboard so that it is firmly attached to the hoop. 9. Insert the felt bass drum beater (I) and adjust so that the beater strikes the middle of the bass drum head (C). Tighten with the drum key. Tom Mounting: 10. Insert the rack tom holder (J) into the rack tom mount (K) on the bass drum and tighten the screw. Use this to adjust the height of the toms. 11. Slide each tom tom (L) on the left and right side of the rack tom mount. Cymbal Mounting: 12. Locate the cymbal stand (M). Insert into the cymbal mount (N) on the bass drum and secure. Unscrew cymbal topper (O) and one felt. 13. Place the cymbal (P) on the stand with one felt below the cymbal. Reattach the top felt and cymbal topper. Please note that the topper doesn’t need to be screwed down hard on the felt and cymbal and the cymbal should be free to move during play, its main operation is to prevent the cymbal from falling off the stand when struck. Floor Tom: 14. After placing the heads and rims on the floor tom (Q) in the same way as you have attached the bass drum, insert the long floor tom legs (R) that raise it off the floor. Snare Drum Stand: 15. Open the snare drum stand base (S) so that the three legs are flat on the floor. Align three cradle arms (T) provided, insert wing nut (U) into the hole and loosely tighten onto snare stand. 16. Place the snare (V) onto the cradle arms, adjust the cradle arms so it fits snugly against the lower hoop of the snare drum. Tighten the wing nut. When fitting the snare drum, the drum head with logo faces up. 5-Piece Junior Drum Kit Assembly Instruction Hi-Hat Stand: 17. Fold the Hi-Hat Pedal (W) down and loosen the hi-hat stand leg wing nut. Extend the 3 hi-hat stand legs (X) out so that the black pedal brace support (Y) is approximately 1 inch off of the floor. Unscrew the pedal holding peg (Z) from the bottom of the brace support, line up the holes from pedal base, reinsert the hold- ing peg and secure with the bolt. 18. Remove the Hi-Hat clutch (a) by loosening the wing nut and pulling it up off of the hi-hat stand drive shaft (b). Place 1 of the Hi-Hat cymbals, concave side up, on top of the felt pad, metal washer and saddle (c). The adjustment screw on the bottom of the saddle adjusts the tilt of the high hat. Drum Throne, AKA Stool: 19. Open the drum throne base (d) so that the three legs are extended fully and flat on the floor. Insert the seat post into the block underneath the throne top (e) and secure. Adjust sitting height and secure. 20. Once seated, you can now bring the set together and fully adjust any heights and angles of the drums, cymbal, and stands to your liking. Enjoy!.
Recommended publications
  • Nitro Drum Kit Assembly Guide
    Assembly Guide Guía de armado Guide de montage alesis.com Guida di montaggio Montageanleitung Manual Version 1.0 Note: Use the drum key (V) to loosen or 1 tighten the bolts of clamps when assembling 23 the kit or making adjustments. E F Nota: Use la llave (V) para aflojar o apretar F F los pernos de las abrazaderas cuando arme el kit o haga ajustes. Remarque : Utilisez la clé de batterie (V) E pour dévisser ou resserrer les boulons des bagues de fixation lors de l’assemblage de A B l'ensemble pour batterie ou pour faire des A B ajustements. CD G Nota bene: servirsi della chiave della batteria (V) per allentare o stringere i bulloni A/B dei morsetti al momento di montare il kit o di C/D apportare regolazioni. A Hinweis: Verwenden Sie den E/F Stimmschlüssel (V), um die Klemmen bei der Montage des Kits oder bei Anpassungen zu lockern oder festzuziehen. 4 5 H 6 8 I I H H I I I H H H 6 789 L M L/M M J J K Q ON Q J/K P O+N alesis.com Manual Version 1.0 Box Contents Connection Diagram Schema dei collegamenti A (1) B (1) C (1) Contenido de la caja Diagrama de conexión Anschlussübersicht Contenu de la boîte Schéma d’installation Contenuti della confezione Important: Use the cable snake (R) to connect the drum pads and cymbal pads to the module (Q) (as Lieferumfang shown in the Connection Diagram). Importante: Use el grupo de cables (R) para conectar D (1) E (1) F (2) G (1) los módulos de tambores y platillos al módulo (Q) (como se muestra en el diagrama de conexión).
    [Show full text]
  • TD-30 Data List
    Data List Preset Drum Kit List No. Name Pad pattern No. Name Pad pattern 1 Studio 41 RockGig 2 LA Metal 42 Hard BeBop 3 Swingin’ 43 Rock Solid 4 Burnin’ 44 2nd Line 5 Birch 45 ROBO TAP 6 Nashville 46 SATURATED 7 LoudRock 47 piccolo 8 JJ’s DnB 48 FAT 9 Djembe 49 BigHall 10 Stage 50 CoolGig LOOP 11 RockMaster 51 JazzSes LOOP 12 LoudJazz 52 7/4 Beat LOOP 13 Overhead 53 :neotype: 1SHOT, TAP 14 Looooose 54 FLA>n<GER 1SHOT, TAP 15 Fusion 55 CustomWood 16 Room 56 50s King 17 [RadioMIX] 57 BluesRock 18 R&B 58 2HH House 19 Brushes 59 TechFusion 20 Vision LOOP, TAP 60 BeBop 21 AstroNote 1SHOT 61 Crossover 22 acidfunk 62 Skanky 23 PunkRock 63 RoundBdge 24 OpenMaple 64 Metal\Core 25 70s Rock 65 JazzCombo 26 DrySound 66 Spark! 27 Flat&Shallow 67 80sMachine 28 Rvs!Trashy 68 =cosmic= 29 melodious TAP 69 1985 30 HARD n’BASS TAP 70 TR-808 31 BazzKicker 71 TR-909 32 FatPressed 72 LatinDrums 33 DrumnDubStep 73 Latin 34 ReMix-ulator 74 Brazil 35 Acoutronic 75 Cajon 36 HipHop 76 African 37 90sHouse 77 Ka-Rimba 38 D-N-B LOOP 78 Tabla TAP 39 SuperLoop TAP 79 Asian 40 >>process>>> 80 Orchestra TAP Copyright © 2012 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Roland and V-Drums are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.
    [Show full text]
  • Product Guide 2020
    Product Guide 2020 ZILDJIAN 2020 PRODUCT GUIDE CYMBAL FAMILIES 3 K FAMILY 5 A FAMILY 13 FX FAMILY 17 S FAMILY 19 I FAMILY 21 PLANET Z 23 L80 LOW VOLUME 25 CYMBAL PACKS 27 GEN16 29 BAND & ORCHESTRAL CYMBALS 31 GEAR & ACCESSORIES 57 DRUMSTICKS 41 PRODUCT LISTINGS 59 1 Product Guide 2 THE CYMBAL FAMILY 3 Product Guide 4 THE FAMILY K ZILDJIAN CYMBALS K Zildjian cymbals are known for their dark, warm sounds that harkens back to the original K cymbals developed by Zildjian in 19th Century Turkey. Instantly recognizable by their ˝vented K˝ logo, K cymbals capture the aura of original Ks but with far greater consistency, making them the choice of drummers from genres as diverse as Jazz, Country and Rock. RIDES SIZES CRASHES SIZES HIHATS SIZES EFFECTS SIZES Crash Ride 18˝ 20˝ 21˝ Splash 8˝ 10˝ 12˝ HiHats 13˝ 14˝ Mini China 14˝ Ride 20˝ 22˝ Dark Crash Thin 15˝ 16˝ 17˝ 18˝ 19˝ 20˝ K/Z Special HiHats 13˝ 14˝ EFX 16˝ 18˝ Heavy Ride 20˝ Dark Crash Medium Thin 16˝ 17˝ 18˝ Mastersound HiHats 14˝ China 17˝ 19˝ Light Ride 22˝ 24˝ Cluster Crash 16˝ 18˝ 20˝ Light HiHats 14˝ 15˝ 16˝ Dark Medium Ride 22˝ Sweet Crash 16˝ 17˝ 18˝ 19˝ 20˝ Sweet HiHats 14˝ 15˝ 16˝ Light Flat Ride 20˝ Sweet Ride 21˝ 23˝ DETAILS: Exclusive K Zildjian random hammering, traditional wide groove lathing, all Traditional except 21” Crash Ride 6 SPECIAL DRY K CUSTOM CYMBALS K Custom cymbals are based on the darker, dryer sounds of the legendary K line but have been customized with unique finishes, K CUSTOM SPECIAL DRY CYMBALS tonal modifications, and manufacturing techniques.
    [Show full text]
  • Percussion Primer / Triangle by Neil Grover
    Percussion Primer / Triangle by Neil Grover SELECTION The triangle should be the highest, non-pitched member of the percussion family. Sizes range from 4” to 10”, however, the best size for concert playing is between 6” and 9”. A larger triangle provides a bigger internal working area for easier execution, however, it is heavier and more difficult to control. Triangles are made from steel, brass or bronze, each producing a different sonority. SUSPENSION A triangle needs to be suspended so that it vibrates unencumbered and freely, al- lowing maximum overtone resonance to be produced. It is very important that the instrument be suspended using a very thin, yet strong, mono-filament line. Fishing line works great and is also inexpensive. The use of string, cable, shoelaces, etc. will effec- tively dampen the resonance of any triangle. Using a second “catch line” will pre- vent the triangle from falling to the floor, should the primary line break. A light “triangle clip” will allow the triangle to be mounted on a music stand when not in use. STROKE The triangle should never be played when mounted on a music stand. It should al- ways be held at eye level and struck on the bottom leg with a motion that “pushes away” the bottom leg. This method will produce the maximum overtone sonority. A triangle sound full of overtones will blend with other instruments. Remember, a tri- angle is a non-pitched instrument and should have a very lush array of overtones, it should not sound like a bell! BEATERS Beaters are available in a large variety of sizes (diameters), materials and shapes.
    [Show full text]
  • The Orchestra What Does an Orchestra Play?
    The Orchestra What does an orchestra play? But what is music? What is sound? Vibrations ♫ An instrument makes sound when it vibrates. Vibrations create sound waves. ♫ Big waves create low sounds and small waves create high sounds. Small wave = High Sounds Big wave = Low Sounds Instruments ♫ BIG instruments create _____BIG sound waves. ♫ This means BIG instruments create ______LOW sounds. ♫ SMALL instruments create ________SMALL sound waves. ♫ This means SMALL instruments create ______HIGH sounds. The Orchestra ♫ An orchestra is a large group of instruments. ♫ It is split up into four sections, these are called families. The Families Each family in the orchestra is made up of instruments with similar characteristics. These characteristics can be: ♫ What the instruments look like ♫ How they are played ♫ What they are made of It is when ALL FOUR families are playing together they create an orchestra. String Family The family of instruments which has strings. The sound is produced by dragging a bow across the strings or by plucking them with the fingers. Violin Cello Harp Viola Double Bass The Violin HEAD Scroll 4 Strings Finger Board Tuning Pegs NECK Bridge BODY ‘F’ Holes Tail Piece Chin Rest String Family String instruments can be played in lots of different ways!! Arco ~ Played with the bow Pizzicato ~ Plucked with the fingers Col Legno ~ Played with the wood of the bow Strumming ~ Using fingers or a plectrum to play notes String Family ♫ The _______violin is the smallest of the string family. It plays the _________highest sound. ♫ The _____________double bass is the ________biggest in the string family. It plays the lowest sound.
    [Show full text]
  • Drum Kit List
    DRUM KIT LIST LISTE DES KITS DE BATTERIE LISTA DE CONJUNTOS DE BATERÍA DRUM KIT-LISTE Drum Kit List / Liste des kits de batterie/ Lista de conjuntos de batería / Drum Kit-Liste • Same as Standard Kit 1 • Comme pour Standard Kit 1 • No Sound • Absence de son • Each percussion voice uses one note. • Chaque sonorité de percussion utilise une note unique. Voice No. 117 118 119 120 121 122 Keyboard Standard Kit 1 Standard Kit 1 Indian Kit Arabic Kit SE Kit 1 SE Kit 2 Note# Note + Chinese Percussion C1 36 C 1 Seq Click H Baya ge Khaligi Clap 1 Cutting Noise 1 Phone Call C#1 37 C# 1Brush Tap Baya ke Arabic Zalgouta Open Cutting Noise 2 Door Squeak D1 38 D 1 Brush Swirl Baya ghe Khaligi Clap 2 Door Slam D#1 39 D# 1Brush Slap Baya ka Arabic Zalgouta Close String Slap Scratch Cut E1 40 E 1 Brush Tap Swirl Tabla na Arabic Hand Clap Scratch F1 41 F 1 Snare Roll Tabla tin Tabel Tak 1 Wind Chime F#1 42 F# 1Castanet Tablabaya dha Sagat 1 Telephone Ring G1 43 G 1 Snare Soft Dhol 1 Open Tabel Dom G#1 44 G# 1Sticks Dhol 1 Slap Sagat 2 A1 45 A 1 Bass Drum Soft Dhol 1 Mute Tabel Tak 2 A#1 46 A# 1 Open Rim Shot Dhol 1 Open Slap Sagat 3 B1 47 B 1 Bass Drum Hard Dhol 1 Roll Riq Tik 3 C2 48 C 2 Bass Drum Dandia Short Riq Tik 2 C#2 49 C# 2 Side Stick Dandia Long Riq Tik Hard 1 D2 50 D 2 Snare Chutki Riq Tik 1 D#2 51 D# 2 Hand Clap Chipri Riq Tik Hard 2 E2 52 E 2 Snare Tight Khanjira Open Riq Tik Hard 3 Flute Key Click Car Engine Ignition F2 53 F 2 Floor Tom L Khanjira Slap Riq Tish Car Tires Squeal F#2 54 F# 2 Hi-Hat Closed Khanjira Mute Riq Snouj 2 Car Passing
    [Show full text]
  • NEW! We Have the Largest Selection of Hard to Find Items. Call
    410 DRUM & PERCUSSION PRODUCTS NEW! ALESIS DM7 USB 5-PIECE ALESIS PERFORMANCE PAD PRO MULTI- ELECTRONIC DRUMSET A 5-drum PAD This 8-pad multi-percussion instrument fea- and 3-cymbal drum kit featuring the tures over 500 sounds and has a 3-part sequencer DM7 USB-enabled drum module so you can play live, create loops and sequences, with more than 400 stereo sounds in or accompany yourself. It includes studio effects, 80 kits. The module features a flex- velocity-sensitive drum pads, large LCD display, a lightweight and durable enclosure, ible metronome and learning exer- 24-bit audio outputs, traditional 5-pin MIDI output jack, and a mix input for external cises, record feature, 1/4" line in/out, tracks, loops, and instruments. headphones out, USB connectivity, ITEM DESCRIPTION PRICE 30 custom drum kits with customi- KICK PEDAL PERFORMANCEPAD-PRO.......8-pad percussion instrument .......................................... 299.00 zable individual drum and cymbal NOT INCLUDED sounds with volume, pan, tuning, and reverb settings. It has 8 studio EQ settings to ALESIS PERCPAD COMPACT 4-PAD PERCUSSION create the perfect room, club, or stadium sound. It offers (1) large, triple-zone snare INSTRUMENT Has 4 velocity-sensitive pads, a kick pad, (3) single-zone 8" tom pads, (1) 8" Hi-hat and control pedal, (1) kick pad with input and high-quality internal sounds –in a compact stand, (1) 12" Crash with choke, and (1) 12" Ride. It has a pre-assembled, 4-post rack size. Mounts to standard snare stand, tabletop surface, for quick set up and stable support and includes rack clamps and mini-boom cymbal or use the optional Module Mount.
    [Show full text]
  • Make It Happen
    Make it Happen 1 Volume, 1 DVD 2 printed scores by Enrico Bertelli PhD Music University of York September 2012 Y3479621 PhD Enrico Bertelli Abstract Works for percussion are often neglected and underperformed because of instrumental unavailabil- ity, logistic limitations and notation issues. This research addresses these problems by delivering eight self-contained, adaptable and transportable multipercussion-based projects. The first three works solve these problems by using found objects, body percussion and imaginary instruments, revolving around the concept of interchangeable, if not transportable, instrumentation. The fol- lowing two projects look at the snare drum as a harmonious box (a resonant body), augmenting its timbre with extended techniques - such as mallets and hybrid hand/stick techniques- and live electronics. The audio processing starts with short and crisp sounds and looks at ways to gen- erate pitch via resonators, and how to control length with reverb. The remaining three projects focus exclusively on MIDI percussion, filling a wide gap in the repertory. These are the first works composed with this instrument in mind and not as a transcription or as a substitute for more common instruments. They cover, respectively, the areas of sampling, automated pitch randomizers and live MIDI scaling and shaping. Furthermore, the max4live MIDI patches serve as a link between the pitched and unpitched percussion, empowering the drum kit with harmonic and melodic controls. All the projects are designed to solve logistic problems and are developed as concerts-in-a-suitcase, a concept which is at the basis of my research Make it Happen. All the scores and types of notation put the performer’s needs first; this is why I produced performance editions, sometimes to the disadvantage of the original composition.
    [Show full text]
  • A Guide to Cymbals, Part 4 by Nick Petrella
    A Guide to Cymbals, Part 4 by Nick Petrella PLACEMENT The optimum place for cymbals in concert ensembles is either between the snare and bass drum or with the accessories between the snare drum and mallet keyboard instruments. The number of people covering parts and the instrumentation will be the deciding factor. In marching ensembles, the cymbals may be placed anywhere in the pit. Again, the number of people and instrumentation will be the deciding fac- tor. An important sound factor is removing the hand cymbal players from in front of the snare drummers as soon as the cymbal pattern is finished. If not, they will absorb a lot of sound, especially if there are sound scoops on the snare drums. Music and Tray Stand Placement The important consideration with music stand placement is to keep it high enough to see the music and the conduc- tor. Percussionists should place the music stand at an angle so the music is not blown away by the wind produced by playing the hand cymbals. Carpeted tray tables are more versatile than cymbal cradles because they are easy to use and can hold sticks, mallets and small instruments as well as cymbals (Figures 31 and 32). They are inexpensive to make. No noise oc- curs when setting the cymbals down because the straps touch the cymbals. A tiered tray stand works well too as it holds a collection of small instruments, sticks and mallets on stage. Whether a tray table or cymbal cradle is used, it should be placed between the percussionist and the conductor.
    [Show full text]
  • 10186 SPL D4420 D4522 Assembly Manual.Indd
    unity kit D4420&D4522DrumSetOwner’sManual 4-PieceShellPackPlus DrumKit(D4420) 5-PieceCompleteDrumKit (D4522) SoundPercussionLabs.com 10186 SPL D4420 D4522 Assembly Manual.indd 1 6/12/14 4:20 PM Thank you for purchasing this kit from Sound Percussion Labs’ outstanding line of drums, percussion and hardware. They offer unlimited enjoyment and will create a solid foundation for your playing. This owner’s manual includes two drum kit models. Be sure to locate the model number of your kit to follow the correct assembly instructions. These instructions should be used as only a general guide. Make adjustments for your comfort and playing style. Experimentation can lead to unique and great experiences in your playing and your music. So experiment with your setup and enjoy! Also, be sure to visit www.soundpercussionlabs.com for more information on Sound Percussion Labs products and support. Table of Contents D4420 Parts Index 2 D4522 Parts Index 3 Bass Drum Head Assembly 4 Bass Drum Leg Assembly 4 Floor Tom Head Assembly 4 Floor Tom Leg Assembly 5 Mounting the Toms to the Bass Drum 5 Cymbal Stand Assembly 6 Snare Drum Stand Assembly 6 Attaching the Bass Drum Pedal 6 Hi-Hat Cymbal Stand Assembly 7 Assembling the Drum Throne 8 Top View Drum Placement 8-9 unity kit Drum Set Owner’s Manual 10186 SPL D4420 D4522 Assembly Manual.indd 2 6/12/14 4:20 PM 4-Pieceunity kit PartsIndex D4420 E A F G B C D I J K N H M O L P Q R SET INCLUDES: L Hoops: Two Floor Tom Hoops Drums: Two Mounted Tom Hoops A 20”x16” Bass Drum Two Bass Drum Hoops B 14”x12” Floor Tom
    [Show full text]
  • Reason Drum Kits Operation Manual
    REASON DRUM KITS OPERATION MANUAL The information in this document is subject to change without notice and does not represent a commitment on the part of Propellerhead Software AB. The software described herein is subject to a License Agreement and may not be copied to any other media except as specifically allowed in the License Agreement. No part of this publication may be copied, reproduced or otherwise transmitted or recorded, for any purpose, without prior written permission by Propellerhead Software AB. ©2019 Propellerhead Software and its licensors. All specifications subject to change without notice. Reason, Reason Intro, Reason Lite and Rack Extension are trademarks of Propellerhead Software. All other commercial symbols are protected trademarks and trade names of their respective holders. All rights reserved. Reason Drum Kits Introduction The Reason Drum Kits instrument is a Rack Extension version of the mighty popular Reason Drum Kits ReFill. Anyone with experience in professional studio work will tell you that recording drums is the most difficult and demanding part of any project. Hands down. Drum recording is a craft which takes decades to learn, yet never gets any easier. It's exhausting. It's expensive. It can make or break an entire production. Due to these challenging demands, the means for capturing the ultimate drum sound have always been out of reach for everyone except those who never get cold sweats from the tick tock of the studio clock. Until now. We took care of the hard part, and the result is Reason Drum Kits - a powerful and versatile drum tool that tears down the last barrier between the virtual studio workspace and the real drum recording studio, and closes the quality gap between “merely” professional and world class! Be the drummer - and the engineer! Traditionally, the structure of computer based drum tools has been dictated by the anatomy of the drum kit.
    [Show full text]
  • Relationship with Percussion Instruments
    Multimedia Figure X. Building a Relationship with Percussion Instruments Bill Matney, Kalani Das, & Michael Marcionetti Materials used with permission by Sarsen Publishing and Kalani Das, 2017 Building a relationship with percussion instruments Going somewhere new can be exciting; it might also be a little intimidating or cause some anxiety. If I go to a party where I don’t know anybody except the person who invited me, how do I get to know anyone else? My host will probably be gracious enough to introduce me to others at the party. I will get to know their name, where they are from, and what they commonly do for work and play. In turn, they will get to know the same about me. We may decide to continue our relationship by learning more about each other and doing things together. As music therapy students, we develop relationships with music instruments. We begin by learning instrument names, and by getting to know a little about the instrument. We continue our relationship by learning technique and by playing music with them! Through our experiences and growth, we will be able to help clients develop their own relationships with instruments and music, and therefore be able to 1 strengthen the therapeutic process. Building a relationship with percussion instruments Recognize the Know what the instrument is Know where the Learn about what the instrument by made out of (materials), and instrument instrument is or was common name. its shape. originated traditionally used for. We begin by learning instrument names, and by getting to know a little about the instrument.
    [Show full text]