DOCSLIB.ORG

Construction of a Simple Gas- Delivery Apparatus SCIENTIFIC Demonstration Procedure

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Construction of a Simple Gas- Delivery Apparatus SCIENTIFIC Demonstration Procedure Construction of a Simple Gas- Delivery Apparatus SCIENTIFIC Demonstration Procedure Introduction Collect gases for classroom study using this simple, inexpensive gas-delivery apparatus. Concepts • Generation of gases • Pressure and vacuum Materials Bent glass tubing Medicine dropper, glass piece only Cork borer, 12–20 mm diameter One-hole rubber stopper, size 10 Gas generator bottle or flask Pinch clamp Glycerin Plastic freezer bag, quart size Hydrochloric acid, 3 M (optional) Thistle tube Latex or rubber tubing, ~ 24 inches Two-hole rubber stopper, size 10 Marble chips, calcium carbonate, CaCO3 (optional) Vacuum pump or aspirator Safety Precautions Check all connections and carefully follow directions—generating gases in a closed system can be very hazardous. Wear chemical splash goggles, chemical-resistant gloves, and a chemical-resistant apron. Please review current Material Safety Data Sheets for additional safety, handling, and disposal information for all chemicals used to generate gases. Procedure Construct the Gas-Delivery Apparatus 1. Use a large, sharpened cork borer to cut a large hole (12–20 mm) in a size 10, one-hole rubber stopper. The result is a stopper with a plug that can be removed (the plug has the original single hole in it). 2. Remove the plug from the stopper and push the plastic freezer bag through the hole in the stopper, leaving about 1 inch of the bag sticking out of the opening. Push the bag through the hole so the bag opening is on the larger side of the stopper (Figure 1). 3. Place the smaller, one-hole stopper “plug” into the freezer bag opening. The freezer bag should now be held tightly between the walls of the two stoppers (Figure 2). 4. Carefully insert the tapered end of a medicine dropper through the small hole in the stopper plug. To do this, place a drop or two of glycerin in the hole and carefully work the dropper back and forth until the tip is inside the bag (Figure 3). #10 Stopper Medicine dropper Freezer bag Freezer bag opening Freezer bag Stopper plug One-hole stopper plug Figure 1. Side View Figure 2. Top View Figure 3. Gas-Delivery Apparatus © 2016 Flinn Scientific, Inc. All Rights Reserved. Publication No. 10527 1 061616 Construction of a Simple Gas-Delivery Apparatus continued 5. Attach a short piece of latex tubing over the top end of the medicine dropper and place the pinch clamp on the latex tubing. 6. Evacuate the gas-delivery apparatus: Remove the pinch clamp and attach the latex tubing to either a vacuum pump or an aspirator. When the bag has been evacuated, replace the pinch clamp on the tubing. Generating a Gas Gases are available in convenient lecture bottle and refillable cylinder sizes. Consult your current Flinn Scientific Catalog/ Reference Manual for a complete listing of gas sources and supplies, including regulator valves. Alternatively, assemble the fol- lowing apparatus for generating carbon dioxide gas. 7. Set up a gas generator using a “gas generation bottle” or a flask equipped with a gas delivery tube, as shown in Figure 4. Note: The “Gas Generation Bottle” available from Flinn Scientific (Catalog No. AP1558) includes the bottle, two-hole stopper, thistle tube, and bent glass tubing. 8. Place marble chips in the gas generator bottle. 9. Carefully pour 3 M hydrochloric acid through the thistle tube until the acid level in the flask is at least 1 cm above the bot- tom of the thistle tube stem. A vigorous reaction will begin immediately. 10. Purge the air from the gas generator system: Allow the gas to escape into the atmosphere or under water for 1–2 minutes before filling the gas-delivery apparatus with carbon dioxide (steps 11–13). Filling the Gas-Delivery Apparatus 11. Attach the end of the latex tubing to a gas source or to the bent glass tubing on the gas generator bottle. Quickly remove the pinch clamp. 12. Slowly and carefully, fill the gas-delivery apparatus with gas. The bag should be taut when filled, but not ready to burst. 13. Remove the latex tubing from the gas source and quickly replace the pinch clamp. The gas-delivery apparatus now contains a slightly pressurized sample of gas. 14. The gas-delivery apparatus may be used to fill syringes with gas for various gas-law and equilibrium experiments. Disposal Save all materials for future use. Connecting to the National Standards This laboratory activity relates to the following National Science Education Standards (1996): Unifying Concepts and Processes: Grades K–12 Systems, order, and organization Constancy, change, and measurement Content Standards: Grades 9–12 Content Standard B: Physical Science, structure and properties of matter, chemical reactions Materials for Construction of a Simple Gas-Delivery Apparatus are available from Flinn Scientific, Inc. Catalog No. Description AP1558 Gas Generation Bottle Consult your Flinn Scientific Catalog/Reference Manual for current prices. 2 © 2016 Flinn Scientific, Inc. All Rights Reserved. .
Load more

Recommended publications
  • Oil Analysis Handbook Third Edition Copyright © 2017 Spectro Scientific
    Predictive Equipment Maintenance Oil Analysis Handbook Third Edition Copyright © 2017 Spectro Scientific. All rights reserved. FluidScan® and LaserNet Fines® are registered trademarks of Spectro Scientific Inc. While every effort is made to assure the information in this document ois accurate, Spectro Scientific does not accept liability for any errors or mistakes that may arise. Specifications are subject to change without notice. | 3 Preface Welcome to the third edition of the In-service Oil Analysis Handbook. It has been a few years since the publication of the first edition of Spectro Scientific’s In-Service Oil Analysis Handbook. Our original goal was to compile a comprehensive reference book of common in-service oil analysis techniques to help readers understand and choose the right technique and instrumentation for their needs. We had to limit the scope in the first two editions because of the amount of effort needed to cover all the topics. In-service oil analysis for condition based maintenance covers a wide array of topics. I am pleased to say that in this third edition, we are much closer to our goal. We reorganized the structure of the content for better clarity and we added articles to cover more topics and instruments associated with oil analysis. Also, we rewrote several articles including the latest developments on the market. As we learned more from our customers about their successes using on site oil analysis, we developed case studies that you can find in this edition. This work is not possible without the time and effort from the contributing authors: Patrick Henning, Daniel Walsh, Robert Yurko, Ken Caldwell, Thomas Barraclough, Maria Bartus, Randi Price, John Morgan, Aifeng Shi and Yuegang Zhao from Spectro Scientific and Ray Garvey from Emerson Process Management.
    [Show full text]
  • Chemical Hygiene and Lab Safety Manual
    CHEMICAL HYGIENE AND LAB SAFETY MANUAL SOUTH DAKOTA SCHOOL OF MINES & TECHNOLOGY Created: 01/12/05 Revision Date: 11/29/2018 FOR OFFICIAL USE ONLY Table of Contents CHEMICAL HYGIENE AND LAB SAFETY MANUAL ...................................................................................................................... 1 1. PURPOSE ...................................................................................................................................................................... 4 2. SCOPE ............................................................................................................................................................................ 4 3. DEFINITIONS (As excerpted from 29 CFR 1910.1450) .......................................................................................... 4 4. EMPLOYEE RIGHTS and RESPONSIBILITIES ....................................................................................................... 6 4.1 EMPLOYEE RIGHTS .......................................................................................................................................... 6 4.1 EMPLOYEE RESPONSIBILITIES ..................................................................................................................... 6 5. ENFORCEMENT ........................................................................................................................................................... 7 6. MEDICAL PROGRAM .................................................................................................................................................
    [Show full text]
  • Gas Generator Bottle Introduction SCIENTIFIC This Gas Generator Setup Provides an Easy Way to Generate and Collect Gas
    Gas Generator Bottle Introduction SCIENTIFIC This gas generator setup provides an easy way to generate and collect gas. Specific instructions are provided for the generation of hydrogen gas using zinc and acid. Concepts • Generation of gases • Water displacement Materials Hydrochloric acid solution, HCl, 3 M Glass plates or Sulfuric acid solution, H2SO4, 3 M Glass tubing Mossy zinc, Zn, 6 g Pneumatic trough Water, tap Rubber tubing Bent glass tubing* Silicone grease packet* Gas collecting bottles or tubes, 3 or 4 Thistle tube* Gas generator bottle* Two-hole rubber stopper* *Materials included. Safety Precautions Hydrochloric acid solution is toxic by ingestion and inhalation and is severely corrosive to skin, eyes and other tissues, as is sulfuric acid solu- tion. Hydrogen gas is a highly flammable gas and a severe fire hazard. Exercise extreme caution when testing the gas and keep the gas generator away from flames. Wear chemical splash goggles, chemical-resistant gloves, and a chemical-resistant apron. This activity requires the use of hazardous components and/or has the potential for hazardous reactions. Please review current Material Safety Data Sheets for additional safety, handling, and disposal information. Procedure 1. Set up the apparatus as shown in the figure to the right. Lubricate the glass tubing and thistle tube with silicone grease before inserting into the stopper. Make sure Thistle tube the water level is above the platform. Prepare bottles for collecting gas by water Two-hole rubber stopper displacement. To do this, fill each gas collecting bottle (or tube) over the brim with tap water, and then cover each with a flat glass plate.
    [Show full text]
  • Flinn Scientific 2019 Purchase Guide a Quick and Easy Checklist of Science Essentials
    Flinn Scientific 2019 Purchase Guide A Quick and Easy Checklist of Science Essentials Use this Purchase Guide as a handy tool for: • Taking Inventory • Order Preparation • Budget Management • Future Planning See your Flinn Scientific Catalog/Reference Manual SCIENTIFIC or visit www.flinnsci.com for product details. It’s Easy to Order Tom Trapp from Flinn Scientific! National Account Development Consultant [email protected] www.flinnsci.com/tom-trapp/sa1001 Online 402-960-5578 (mobile) www.flinnsci.com Offering personal assistance to help meet your science curriculum, supply, and lab safety needs. Email [email protected] Quality Products, Fast Delivery, Fax and Low Prices Guaranteed 1-866-452-1436 (toll free) Mail Flinn Scientific, Inc. P.O. Box 219 Batavia, IL 60510-0219 Phone 1-800-452-1261 7:30 am to 5:00 pm CT Monday through Friday Our Guarantee Flinn Scientific, Inc. guarantees that no sale is complete unless the customer is satisfied. Every item we furnish will either conform to the catalog specification, or we will ask your permission, prior to shipment, to ship an alternative product. If you find a lower published nationally advertised catalog price for an identical item, Flinn will “meet or beat” that price. Use this purchase guide containing popular product recommendations ©2019 Flinn Scientific, Inc. All Rights Reserved. to prepare your order, take inventory, and manage your budget. 1 www.flinnsci.com Flinn Scientific 2019 Purchase Guide 1 Item Rec. Item Rec. Product / Item Name Qty 2019 Price Total Product / Item Name Qty 2019 Price Total No. Qty No. Qty Safety & Personal Protection Equipment Aspirator, Water, Polypropylene AP1203 1 $ 19.30 $ - Apron, rubberized, 27" W X 36" L AP7125 30 $ 15.00 $ - Autoclave, Electric, Portable AP1004 1 $ 865.20 $ - Apron, plastic, 30" W x 36" L AP7120 30 $ 7.25 $ - ♦ Balance, Flinn Triple Beam OB2181 $ 115.00 $ - Gloves, Butyl rubber for conc.
    [Show full text]
  • Sampling and Test Protocols MSHE.003 1997
    Sampling and test protocols MSHE.003 1997 Prepared by: Victorian Institute of Animal Science Published: December 1997 ISBN: 1 74036 626 2 ©1998 This publication is published by Meat & Livestock Australia Limited ACN 081678364 (MLA). Where possible, care is taken to ensure the accuracy of information in the publication. Reproduction in whole or in part of this publication is prohibited without the prior written consent of MLA. Meat & Livestock Australia acknowledges the matching funds provided by the Australian Government and contributions from the Australian Meat Processor Corporation to support the research and development detailed in this publication. MEAT & LIVESTOCK AUSTRALIA Table of Contents Summary report ................................................................................................................................ I Research Summary ....................................................................................................................... 1 Introduction .................................................................................................................................. I Objectives ..................................................................................................................................... I Major Research Findings ............................................................................. : ................................. ! Introduction .....................................................................................................................................
    [Show full text]
  • High School Chemistry
    RECOMMENDED MINIMUM CORE INVENTORY TO SUPPORT STANDARDS-BASED INSTRUCTION HIGH SCHOOL GRADES SCIENCES High School Chemistry Quantity per Quantity per lab classroom/ Description group adjacent work area SAFETY EQUIPMENT 2 Acid storage cabinet (one reserved exclusively for nitric acid) 1 Chemical spill kit 1 Chemical storage reference book 5 Chemical waste containers (Categories: corrosives, flammables, oxidizers, air/water reactive, toxic) 1 Emergency shower 1 Eye wash station 1 Fire blanket 1 Fire extinguisher 1 First aid kit 1 Flammables cabinet 1 Fume hood 1/student Goggles 1 Goggles sanitizer (holds 36 pairs of goggles) 1/student Lab aprons COMPUTER ASSISTED LEARNING 1 Television or digital projector 1 VGA Adapters for various digital devices EQUIPMENT/SUPPLIES 1 box Aluminum foil 100 Assorted rubber stoppers 1 Balance, analytical (0.001g precision) 5 Balance, electronic or manual (0.01g precision) 1 pkg of 50 Balloons, latex 4 Beakers, 50 mL 4 Beakers, 100 mL 2 Beakers, 250 mL Developed by California Science Teachers Association to support the implementation of the California Next Generation Science Standards. Approved by the CSTA Board of Directors November 17, 2015. Quantity per Quantity per lab classroom/ Description group adjacent work area 2 Beakers, 400 or 600 mL 1 Beakers, 1000 mL 1 Beaker tongs 1 Bell jar 4 Bottle, carboy round, LDPE 10 L 4 Bottle, carboy round, LDPE 4 L 10 Bottle, narrow mouth, 1000 mL 20 Bottle, narrow mouth, 125 mL 20 Bottle, narrow mouth, 250 mL 20 Bottle, narrow mouth, 500 mL 10 Bottle, wide mouth, 125
    [Show full text]
  • K–12 Science Safety Manual
    K–12 Science Safety Manual Developed by the Innovative Teaching and Learning Unit Instructional Design and Professional Learning Division K–12 Science Department TABLE OF CONTENTS Importance of Safety 2 General Information 7 Prohibited Practices 9 Emergency Information 10 Safety on Field Trips 15 General Laboratory Safety 20 Elementary Science Safety 22 Biological Science Safety 24 Earth and Space Science Safety 28 Chemistry Science Safety 31 Physics Science Safety 35 Appendix A: Technical Safety Assistance Numbers 49 Appendix B: Safety Survey 50 Appendix C: Lab Inspection Checklist 51 Appendix D: Chemical Storage 55 Appendix E: Waste Disposal 63 Appendix F: Prohibited Chemicals 68 Appendix G: Restricted Chemicals 75 Appendix H: Animals in the Classroom 79 Appendix I: Safety Contracts and Exams 85 Appendix J: Safety Resource Websites 86 Restricted Chemical Request Form 87 Secondary Science Teacher Safety Manual Acknowledgement Form 88 IDPL-SCI-M002, Rev. B September 2009, Rev. C April 2015 0 SPECIAL ACKNOWLEDGMENTS The Clark County School District K–12 Science Safety Manual is a coordinated effort by a team of teachers, administrators, with input from the Southern Nevada Health District. Andy Cheney Environmental Health Supervisor, Southern Nevada Health District Ellen Dunne K–5 Science Project Facilitator, CCSD Instructional Design and Professional Learning Division Eileen Gilligan Elementary Science Coordinator, CCSD Instructional Design and Professional Learning Division Kim Krumland Risk and Environmental Services Department Director,
    [Show full text]
  • Chemistry 1009 Lab Manual University of Louisiana at Monroe
    Chemistry 1009 Lab Manual University of Louisiana at Monroe Department of Chemistry 2010 Version 2.0 Contents Lab Session 1: Laboratory Safety Rules and Check In .................................................. 1 Fire, Injury, Spills and Cleanliness .............................................................................. 2 Desk Assignment Sheet (Chemistry 1009) .................................................................. 4 Commonly Used Equipment (not in the desk drawer)................................................. 5 Lab Session 2, Experiment 1: Introductory Exercises ................................................... 10 Report Form 1 .............................................................................................................. 17 Lab Session 3, Experiment 2: Oxygen ........................................................................... 18 Report Form 2 .............................................................................................................. 21 Lab Session 4, Experiment 3: Preparation of Sodium Chloride .................................... 22 Report Form 3 .............................................................................................................. 25 Lab Session 5, Experiment 4: Law of Definite Proportions .......................................... 26 Report Form 4 ........................................................................................................... 30 Lab Session 6, Experiment 5: Hydrogen and the Activity Series of Metals .................
    [Show full text]
  • Textural Modification of Processing Tomatoes
    Critical Reviews in Food Science and Nutrition, 38(3):173–258 (1998) Textural Modification of Processing Tomatoes Diane M. Barrett,* Elisabeth Garcia, and Jo Ellen Wayne** Department of Food Science & Technology, University of California, Davis, California 95616–8598 * Author to whom correspondence should be addressed. ** Current position is with: Quest International, Silverton, Oregon 97381. Referee: Professor Malcolm C. Bourne, Food Research Laboratory, Geneva, New York 14456–0462 ABSTRACT: Knowledge of the textural properties of processing tomatoes is crucial to ensuing product accept- ability; measurement, control, and optimization of these properties through judicious selection of varieties and control of unit operations results in products that the consumer prefers. It is important to first define the terms texture, rheology, consistency, and viscosity prior to discussing principles of their measurement. The textural properties of processing tomatoes may be measured using both sensory and objective tests, and the latter may be either destructive or nondestructive in nature. The unique anatomy of tomato fruit (peel, pericarp, columella, and locules) in part dictates the method of texture measurement. Numerous factors, including variety, maturity, genetic modification, cultural particles, and environmental conditions, processing conditions, and calcium addition affect the textural integrity of tomatoes. Textural properties of raw tomatoes and most processed tomato products are reviewed in this article. KEY WORDS: textural properties, rheology, viscosity, tomatoes, processed, sensory, objective. I. INTRODUCTION II. TEXTURAL PROPERTIES, VISCOSITY, AND CONSISTENCY Tomatoes are unique fruit vegetables com- posed of varied types of tissues that play a critical According to Bourne (Bourne, 1982), the tex- role in the perception of texture. Tomato products tural properties of a food are the “group of physi- represent an increasing proportion of the U.S.
    [Show full text]
  • Antimicrobial and Antioxidant Activities of Betel Oil
    Kasetsart J. (Nat. Sci.) 40 (Suppl.) : 91 - 100 (2006) Antimicrobial and Antioxidant Activities of Betel Oil Panuwat Suppakul*, Nutcha Sanla-Ead and Panchuti Phoopuritham ABSTRACT Betel oil has been studied for its antimicrobial and antioxidant activities against ten pathogenic and spoilage bacteria and three strains of yeast using an agar well diffusion assay and against oxidative bleaching using a b-carotene agar well diffusion assay, respectively. The minimum inhibitory concentration (MIC) and minimum oxidative bleaching inhibitory concentration (MOBIC) of betel oil were determined using an agar dilution method. At the concentration of 50 mL mL-1, betel oil showed a zone of inhibition, ranging from 9.15 to 17.30 mm in diameter. The MICs of betel oil in a range of 12.5- 100 mL mL-1 could inhibit the growth of all test microorganisms except Pseudomonas aeruginosa, which was not sensitive to this oil even at the highest concentration (200 mL mL-1). The most sensitive bacteria to betel oil were Listeria monocytogenes and Salmonella Enteritidis. Betel oil (100 mL mL-1) also revealed ability to inhibit the oxidation of b-carotene, yielding a yellow zone surrounding the well with a 8.40 mm in diameter. The MOBIC of betel oil was 100 mL mL-1. Betel oil might have a potential application in controlled and released food packaging technology as antimicrobial and antioxidant agents. Key words: betel; antimicrobial; antioxidant; MIC; MOBIC INTRODUCTION Prevention of pathogenic and spoilage microorganisms in foods is usually achieved by The appearance of foods is one of the using chemical preservatives. These chemical major determinants of its sensory appeal to preservatives act as antimicrobial compounds consumers and consequently, sales of the product.
    [Show full text]
  • Science Apparel, Balance & Scales
    Science Apparel, Balance & Scales APPAREL / APRONS Mass Set Attachment Used to increase balance capacity to Rubberized Aprons 2610g, consists of 2-1,000g masses Light weight, charcoal colored, acid resistant and 1-500g mass. Qualifying Standard: cloth sheeting. Protects from chemical splashes Ohaus. with cotton ties at neck and waist. Reinforced stress points. Qualifying Standard: Quincy • For use with KCDA No. 02215 and Ohaus models 750SO, Specialties, Toplab. 710, 710T, 720, 760 and 730. KCDA No. U/M KCDA No. Size U/M 02200 ...................................................................................................3/Set 44028 .............. 24”Wx30”L - Childs .........................................................Ea 02150 .............. 27”Wx36”L - Adult ...........................................................Ea Scout Pro USB Interface Translucent Plastic Aprons This interface kit is a unique solution Resistant to laboratory reagents, acids, oils, to the problem of connecting a balance alkalies and grease, tapes at waist and neck, to a computer using a Universal Serial 6 ml thickness, reinforced at points of strain, Bus (USB). Data sent from the balance individually packaged. Qualifying Standard: to a computer is in USB format. The Quincy. USB data is directed to a virtual port. KCDA No. Size U/M This port then appears as an RS232 02157 .............. 27”Wx36”L - Adult ...........................................................Ea port to the application program. Ohaus, 44029 .............. 24”Wx30”L - Childs .........................................................Ea No Substitute. • Fits KCDA Nos. 02211, 02212, 02219 and 04540. APPAREL / COATS KCDA No. Mfg. No. U/M 02240 .............. 7114737 ..........................................................................Ea Lab Coats Ohaus Pan Cover White, twill woven blend of 65% Stainless steel weighing pan cover. Ohaus, No polyester and 35% cotton, 3 single Substitute. pockets and collar. 43” long, Qualifying • Fits KCDA Nos.
    [Show full text]
  • Laboratory Arts & Recipes Take 3
    1 LABORATORY ARTS AND RECIPES BY Peter Ellis (Bendigo Senior Secondary College) (Nov. 2007, Revised Nov.08, Sept.09, April 10) Edited by J.Hasse (Sunbury College) Contents 2 1. Drilling holes in stoppers and removing broken glass ...…..p 3-4 2. Rubber tubing versus plastic tubing ……………………….p 5 3. Rubber stoppers versus corks ……………………………...p 5 4. Hot fingers ………………………………………………....p 5 5. Marking or coding crucibles ……………………………….p 5 6. Marking or coding glassware …………………………….. .p 5 7. Labelling …………………………………………………...p 6 8. Removing residues from test tubes and cleaning glassware..p 6-12 9. Making Starch Solution (& Cooling Bath) ………………...p 13 10. Cutting glass tubing and rod ……………………………...p 13 11. Making Glass Test Loops ……………………………….. p 15 12. Making U Bends ……………………………………….... p 16-19 13. Agar Gel Salt Bridges ………………………………….... p 20 14. Setting up a Kipp‟s Apparatus (Gas Generator) ……….... p 20-22 15. Bunsen Burner Maintenance …………………………….. p 22 16. Maintenance of Burettes ………………………………... p 22 17. Seized Quickfit and glass joints, stoppers ………………. p 23 18. Weighing and transferring Chemicals for Reagents ……. p 23 19. Flame Tests ……………………………………………... p 24 20. Gas Leaks ……………………………………………….. p 24 21. Folding Filter Papers (General, Improved & Fluted) …… p 25-26 22. Seating Glass Stoppers in Reagent Bottles ……………... p 27 23. Fixing broken Filter Funnel stems …………………….... p 28 24. Repairs to Burettes & Pipettes ………………………….. p 29 25. Transferring reagents from stoppered bottles …………... p 34 26. What is a RG? ………………………………………….. p 35 27. Placing a sample in a Melting Point Tube ……………… p 35 28. Using a Mortar & Pestle (& Triturating)…………………p 35 29. Fixing faded graduations on glassware …………………. p 35 30. Discarding sodium scraps ……………………………….
    [Show full text]