Solder Fast Zinc #503-029 Joins Most Metals, Including Copper, Brass, Stainless Steel, Nickel and Bronze

Total Page：16

File Type：pdf, Size：1020Kb

Solder Fast Zinc #503-029 Joins most metals, including copper, brass, stainless steel, nickel and bronze. Not for use on aluminum, magnesium, or pot metal. If Solder Fast flux burns off before solder flows, apply a small amount of Solder Fast flux (#503-040) to the area. Store at room temperature (60°-78°F/15–25°C). If stored above 80°F/27°C, solder and flux will separate. Tensile strength: 22,000psi Ingredients: Tin, silver, petrolatum glycerine, ammonium tetrafluoroborate, aminoethylethanolamine, zinc oxide (fume), bismuth. Flow Temperature: 400°F/204°C Directions: No additional flux is necessary. No training is required. Solder Fast can be used with a soldering iron, open flame, butane, propane, mapp or acetylene gases. The solder finish is bright and won't tarnish or blacken. 1. Thoroughly clean the surfaces being soldered. Remove all dirt, grease and buffing compounds. 2. Position all parts to be joined for good contact. Where necessary, use tweezers, clamps or a vise to maintain contact. 3. Apply a sufficient quantity of paste solder to the joint. 4. Heat lightly at first. If solder does not flow instantly, apply more heat to the metal and around the joint until solder flows. 5. Wash off flux residue with warm water and a stiff brush. Do not use jewelry pickling solution on Solder Fast. First Aid Procedures Eyes: Flush with water for 15 minutes holding eyelids open. Seek medical attention. Skin: Wash area with soap and water. Seek medical attention if irritation persists. Inhalation: Remove person to fresh air. Restore breathing if necessary. Seek medical attention. Ingestion: Seek medical attention immediately. DO NOT induce vomiting. Leak or Spill Procedures: Wear personal protective equipment. Use an inert absorbent material. Sweep or scoop up spill, and place into a suitable sealed container. Please refer to the MSDS for more information. 7500 Bluewater Road NW • Albuquerque, NM 87121-1962 USA 1-800-545-6566 • FAX: 1-800-965-2329 • Local: 505-839-3300 International: 505-839-3011 • International FAX: 505-839-3016 © 2002Rio Grande/The Bell Group, Inc. 503-029/031502/rm/150.

Copy Link

Recommended publications

Maintenance and Repair Alloys for Welding, Brazing, Soldering and Metal Working
Maintenance and Repair Alloys for Welding, Brazing, Soldering and Metal Working Weldcote Metals Maintenance and Repair Alloys for Welding, Brazing, Soldering and Metal Working ________________________________________________________________________________________________________ Dissimilar metal combinations - 120,000 psi tensile Super 120 Electrodes are excellent for repairing tools, dies, spring steel and any dissimilar metal combinations, except for aluminum and copper alloys due to exceptional strength and crack resistance. Super 120 is also recommended for repairing worn parts and as an underlay for hardfacing. Applications: repairing tools, dies, spring steel and any dissimilar metal combinations. Consider this the maintenance and repair “stand-by” in every industry throughout the world. Procedure: Use either AC or DC reverse polarity (electrode +). The weld area should be free of rust, grease, paint and other materials which cause weld contamination. A 90° vee joint should be used when joining heavy sections. Maintain a short arc length and use stringer beads. For high carbon steels, a preheat of 400° is recommended. Weld positions are flat, horizontal, vertical up and overhead. Amperages: 3/32” = 35 – 70 1/8” = 60 – 110 5/32” = 75 – 140 3/16” = 130 - 200 Super 120 3/32 electrode SUPER120332E 4-10 lb tubes in 40 Super 120 1/8 electrode lb ctn SUPER12018E Super 120 5/32 electrode SUPER120532E Aluminum cast & wrought base metal Aluminum Smooth 340 Maintenance and Repair electrodes feature a precise combination of core wire and coating, providing high speed deposition of dense, machinable welds. It is recommended for fabrication and repair of cast and wrought aluminum. It is excellent for foundry defects, machining errors and all types of salvage work.
[Show full text]
Aluminium Repair System Brazing Rods
4707 Aluminium Repair System Brazing Rods Description Packaging Card in polybag For non-ferrous metals and all aluminium components This product can repair most damage to aluminium parts quickly and Section Within Catalogue effectively without using flux or chemicals. General Hand Tools Expensive down time can be reduced by repairing the component rather than replacing it. Page Number in Catalogue NEW Opportunities include Motor Racing | bicycles | aluminium windows | aluminium boat hulls air conditioning units | industrial Contents. Contents 5 x Aluminium brazing rods, 1 x Tinning brush, 1 x DVD promotional video and demonstration. Additional Information 20 May 2009 Heat source required Distributed by The Tool Connection Ltd. Kineton Road | Southam | Warwickshire | CV47 0DR T | +44 (0) 1926 815 000 F | +44 (0) 1926 815 888 E | [email protected] www.toolconnection.co.uk Over 260°C below melt point of aluminium Use any heat source Propane | Butane | Mapp | Blow torch Brazes all aluminium alloys including Zinc | Magnesium | Pot metal | Cast Whether the holes are caused through corrosion or simple breakages, the repair will be stronger than the original component and will withstand high levels of torque. Fill holes up to 3/8" diameter with this second generation brazing rod. Repair threads in aluminium components by filling the hole with the brazing rod. Insert a bolt into the hole and wait for it to set. When cool the bolt can be removed with a simple socket and ratchet and the thread is cut as it is removed. This product can repair any damage to aluminium parts quickly and effectively without using flux or chemicals.
[Show full text]
Trade Name: Kapp Alumitetm Solder Composition: Proprietary Ref
Alumitetm Repair Almost Any Metal With Just a Propane Torch The original fluxless brazing rod for the fabrication, maintenance and repair of Aluminum alloys, Zinc Diecast, Pot Metal, and White Metal. Alumitetm is also an excellent general purpose high strength solder. Repairs aluminum boats, engine heads, motor housings, power mowers, farm and dairy equipment, blocks and crankcases, vacuum cleaners, carburetors, gears and pumps, jigs and fixtures, dies and matchplates, trophies and ornaments, models and patterns, antique car parts, windows and doors, and aluminum boat propellers. Physical Properties and Technical Data o o Melting Range F 715 - 735 F o o Melting Range C 379 - 391 C Tensile Strength 39,800 psi Compression Strength 60,000 - 75,000 psi Shear Strength 34,000 psi Impact Strength (Charpy) 4 ft lbs. to break 1/4" bar Hardness (Brinell/500kg load) 100 Ductility Good Specific Gravity 6.7 lbs./in3 Density .25lbs./in2 Elongation 3% in 2 inches o Coefficient of Linear Expansion15.4 x 106/ F Electrical Conductivity 24.9 (%IACS) o Thermal Conductivity .24 cal/cm3/ C Corrosion Penetration 300 x 106 in. 1 1/R o Foxity None under 1500 F Flux None on Accessible Joint Kapp Lunartm flux on blind joints Available Diameters and Lengths 1/8” by 9”, 12”, 18”, and 36” 3/16” by 18” and 36” 1/4” by 18” and 36” We do not ship 36” rods by UPS due to potential damage to rods. 18” rods ship in 50lb. plain bulk boxes, 36” rods ship in 100lb. plain bulk boxes. Small quantities may be purchased directly from Alumite.com alumitedata 062802 Page 16-18 Fluxless Soldering with Kapp Alumitetm To solder aluminum, the invisible oxide film must be penetrated by the solder to obtain metal to metal contact.
[Show full text]
Royal Kirkrod “The Royal Line” Bare Rod for Brazing (TB) and Gas Tungsten Arc Welding (GTAW) ALLOYS COMPANY
Royal Kirkrod Bare Rod for Brazing (TB) and Gas Tungsten Arc Welding (GTAW) “The Royal Line” ALLOYS COMPANY 30105 Stephenson Hwy, Madison Heights, MI 48071 Zinc Alloy (248) 588-3790 (800) 521-7878 www.crownalloys.com Alloy for Welding Zinc-Based Metals or Brazing Aluminum Typical Applications Royal Kirkrod is the most widely used alloy for welding zinc-based metals, white metal and pot metal. These include carburetors, power mower housings, kirksite dies, power tools, trophies and ornaments, vacuum cleaners, antique car parts, models and patterns. Royal Kirkrod is also a very useful self-fluxing brazing alloy for aluminum parts such as boat hulls, propellers, aluminum radiators, doors and furniture. Because the Royal Kirkrod is alloyed from pure, virgin metals, deposits are clean and free from slag. Joints made with Royal Kirkrod are permanent, non-corrosive and stronger than the parent metal. Specifications • Tensile Strength 39,000 PSI • Compressive Strength 93,100 PSI • Hardness 100 Brinell • Elongation in 2” 8.4% o o • Melting Range 715 F to 735 F Procedure Brazing: For zinc-based metals: Vee the broken edges to 45o. Clean weld area thoroughly. Heat fracture directly with a neutral flame until the surface oxides of the base metal can be scratched open by jabbing it with the Royal Kirkrod. Keep the rod away from the flame as much as possible when starting to weld. Finish by puddling the Royal Kirkrod in the base metal. COOL SLOWLY! For Aluminum: It is critical that the tough aluminum oxides are removed with a clean stainless steel wire brush before brazing and then are penetrated by scratching the rod across the heated aluminum surface.
[Show full text]
ELECTROLESS NICKEL/Krome PLATING KITS
Email: [email protected] Web Page: www.caswelleurope.co.uk ELECTROLESS NICKEL/Krome PLATING KITS So simple - just like boiling an egg! The ideal way to plate small parts - easily - economically - quickly. No batteries or power required - simple electrochemical reaction plates automatically. Plates many metals - all steels, irons, copper, brass, bronze, lead free solders and nickel alloys. Plates Aluminium using the Zincate process Plates Pot Metal using Pot Metal Primer Even and uniform plated layer, even in the most difficult corners. Plates @ 1/1000" (25 Micron) per hour Cyanide free - no EPA problems - No fumes No disposal problems - drain safe IMPORTANT! READ ENTIRE BOOKLET BEFORE ATTEMPTING TO OPERATE THE SYSTEM As simple as boiling an egg! These instructions now cover the Nickel and the Krome kits. Electroless Krome is a nickel/cobalt alloy, harder and bluer than nickel. Where these instructions refer to Electroless Nickel, this also means Electroless Krome. The only difference in the kits is the part A component, which, in the case of Krome, has the cobalt additive. You may use parts B & C for either type of plating, as they are completely interchangeable. Electroless nickel/krome plating requires no anodes, power supply or electrical connection of any kind. The process simply involves mixing together some solutions, heating them to just off the boil, and then immersing the part to be plated. An autocatalitic electrochemical reaction takes place and the nickel is evenly deposited all over the part being plated. The thickness of the plate will depend on the duration of immersion. To stop the reaction, the part is removed from the solution, which is allowed to cool before storing for later reuse.
[Show full text]
101 Cleaning Zinc Alloy Fuel Bodies
Cleaning Zinc Alloy Fuel Bodies By Bruce Smith 101 Cincae the inventrion of thbe carbureto r in Csubstitutinhg the Gereman kupfemr for copper. iworsst case sctenario rfor a cayrburetor is to re - the late nineteenth and early twentieth There are various standard formulations and Eu - plenish the gasoline in the float bowl after it Scenturies (when Zenith, Pallas, Pier - ropean casting ZAMAK has a zinc content of evaporates, ensuring a good supply of water sat - burg, and SOLEX were pioneering designs), about 95% with 4% aluminum and 1% copper. urated fuel. Carried out over several years, this there has been a need to clean the residues and Most inorganic reactions are based on this zinc sets up the ideal conditions to maximize zinc re - reactants that accumulate during use. The crud content, which can form deposits and lead to actions. The preventative solutions are to en - that forms in and on carburetors and fuel pumps corrosion damage. Extreme examples result in sure that only fresh gas is in the fuel system and generally falls into two categories: organic (from internal corrosion sufficient enough to damage that the carburetor and fuel pump are run dry petroleum residues, grease and oil) and inor - a casting beyond repair. before storing. ganic (from metal reactants, minerals and A bit of chemistry background is useful to salts). Most of these contaminants can plug jets, understand the processes that occur. Zinc is re - Cleaning Organic & Inorganic Contaminants nozzles, and pathways, preventing proper me - sistant to corrosion if kept reasonably dry. A thin So cleaning an old Zenith or SOLEX carbu - chanical operation.
[Show full text]
Ssf-6 Silver Solder
CATALOG & PRICE LIST 1-866-684-4993 www.MuggyWeld.com SUPER ALLOY 1 Super Alloy 1 is a multi-metal solder that joins all white metals. It can also join white metals to practically any other metal, even ferrous to non-ferrous metals, like steel to aluminum. Super Alloy 1 bonds at half the melting point of pot metal. Its honey flux turns root beer brown to indicate when the base metal has reached the proper bonding temperature, enabling quick and easy repairs. It’s ideal for repairing pot metal pitting, and can be applied with any heat source, including a soldering gun, heat gun, or propane torch with no welding expertise. Key Features: • Solders: pot metal, aluminum, galvanized metal, copper, brass, bronze, steel, zinc die cast, pewter, zinc plated steel, lead • Low working temperature - 350°F - prevents warpage and base metal damage; favored in applications requiring low heat • Works with: propane, MAPP gas, oxyacetylene, butane, heat gun, larger soldering irons, ovens • Can be plated, painted, powder coated, polished, shaped, built-up, missing pieces • Completely non-corrosive; washes off with warm water Note: Super Alloy 1 cannot be used to repair aluminum boats, cast aluminum, large aluminum masses, or diamond plate aluminum. Super Alloy 5 and an oxyacetylene torch are required for these applications. Attribute Super Alloy 1 Melting temperature 350° F Bonding strength 20,000 PSI 3/32 in. or 2.3813 mm Sizes available 1/8 in. or 3.1750 mm Flux Honey liquid (2 year shelf life) Alloy color Silver Yes. Please read http://www.aws.org/library/doclib/fs22- Contains cadmium? 201404.pdf for safety information Recommended torch Propane, MAPP, butane, oxyacetylene Metal warpage No Can bond thick to thin Good (use Super Alloy 5 for thick to thin aluminum) metals? Can join copper, brass, and Yes bronze to other metals All position? Yes Can be plated? Most metals except aluminum Can be polished? Yes Takes powder coating? Yes (re-melt temperature is over 400° F) Pre-cleaning necessary? Yes, with a wire brush, sanding, Dremel etc.
[Show full text]
Super Alloy 1 Instructions: 1. Pre-Clean the Parent Metal Or Metals to Be Joined. Use Emorycloth, Wirebrush, Bead-Blasting, Etc
Super Alloy 1 Instructions: 1. Pre-clean the parent metal or metals to be joined. Use emorycloth, wirebrush, bead-blasting, etc. On cracked or broken pieces it is advisable to "v" out cracks and both sides of broken metal to provide strength. 2. Apply the non-corrosive, liquid flux to the repair area. An easy method of application is to dip the end of the rod into the flux. The flux will cling to the rod and is easily spread with the rod. 3. Use a soft flame, heat gun, or soldering iron to heat the parent metal adjacent to the actual repair. A direct flame on the repair area is likely to overheat the solder and flux. Soldering irons lose the ability to heat well on parts thicker than 1/8" 4. Hold the torch tip four to six inches away from the parent metal. If it is necessary to apply the flame directly on the rod and flux pull the torch tip back even further from the work surface and keep the torch moving. 5. The flux will begin to bubble and turn light brown. Besides preparing the parent metal for the solder, these changes indicate the proper working temperature. If the flux turns black, clean-up the area with warm water and a wire brush and start over. 6. When the flux turns brown it is time to apply the rod. Drag the rod over the area to be soldered until it begins to flow and stop applying the heat. If additional layers are needed, continue dragging the rod over the area while applying heat if the rod doesn't melt.
[Show full text]
MATERIAL SAFETY DATA SHEET Page 1 of 5 DURAFIX Solder for Aluminum, Diecast, Zinc Alloys, Pot Metal and White Metal
MATERIAL SAFETY DATA SHEET Page 1 of 5 DURAFIX Solder for Aluminum, Diecast, Zinc Alloys, Pot Metal and White Metal Trade Name: DURAFIX UK LIMITED Composition: LIMITED REF. Weeks ID No. 204 Manufacturer: Durafix UK Limited Address: 41 Bowland Crescent, Blackpool, Lancashire, England, FY3 7TF Telephone : +44 1253 319132 E-mail: [email protected] Please retain this sheet for your files. Durafix UK Limited maintains a Material Safety Data Sheet (MSDS) for each Durafix in compliance with Federal OSHA Hazard Communication Standard (29 CFR 1910.1200) & various right-to-know laws. The information and recommendations contained within this publication have been compiled from sources believed to be reliable and to represent the best information available to Durafix UK Limited at the time of issue. It is our policy to include an MSDS with initial orders for each product. This submission is to become a matter of record and need not accompany subsequent shipments for the same product to the same customer. The information contained on this sheet is intended solely for employee health and safety education and not for contract specification purposes. No warranty, guarantee, or representation is made by Durafix UK Limited, nor does Durafix UK Limited assume any responsibility in connection therewith; nor can it be assumed that all acceptable safety measures or other safety measures may not be required under particular or exceptional conditions or circumstances. Should you need additional information, contact us. I - MATERIAL IDENTIFICATION /COMPONENTS
[Show full text]
!!!! Warning !!!! Carefully
CAREFULLY !!!! WARNING !!!! CAREFULLY WELDING FUMES AND GASES CAN BE DANGEROUS TO YOUR HEALTH. BEFORE USING THIS PRODUCT THE WELDER (END-USER) MUST READ AND UNDERSTAND THE COMPLETE PRODUCT WARNING LABEL AND MATERIAL SAFETY DATA SHEET (MSDS). THE MATERIAL SAFETY DATA SHEET (MSDS) WHICH OUTLINES THE POTENTIAL HEALTH HAZARDS AND SAFETY INFORMATION RELATED TO THIS PRODUCT CAN BE DOWNLOADED FROM THE MSDS PORTION OF THIS WEBSITE. IT IS ALSO AVAILABLE FROM YOUR EMPLOYER AND WELDING SUPPLY DISTRIBUTOR. DO NOT PROCEED WITH USE OF THIS PRODUCT UNTIL YOU READ AND UNDERSTAND THE MATERIAL SAFETY DATA SHEET (MSDS) AND PRODUCT WARNING STATEMENT. BE SURE TO CONSULT THE LATEST VERSION OF THE MSDS. SEE THE PRODUCT WARNING LABEL AND MSDS FOR COMPLETE WARNING INFORMATION. CAREFULLY CAREFULLY 30105 STEPHENSON HWY. MADISON HEIGHTS, MI. 48071 CROWN ALLOYS (248) 588-3790 ▪ (800) 521-7878 COMPANY Royal Kirkrod Premium Alloy for Welding Zinc-Based Metals or Brazing Aluminum Typical Applications: Royal Kirkrod is the most widely used alloy for welding zinc-based metals, white metal and pot metal. These include carburetors, power mower housings, kirksite dies, power tools, trophies and ornaments, vacuum cleaners, antique car parts, models and patterns. Royal Kirkrod is also a very useful self-fluxing brazing alloy for aluminum parts such as boat hulls, propellers, aluminum radiators, doors and furniture. Because the Royal Kirkrod is alloyed from pure, virgin metals, deposits are clean and free from slag. Joints made with Royal Kirkrod are permanent, non- corrosive and stronger than the parent metal. Specifications: ¾ Tensile Strength 39,000 PSI ¾ Compressive Strength 93,100 PSI ¾ Hardness 100 Brinell ¾ Elongation in 2” 8.4% ¾ Melting Range 715oF to 735oF PROCEDURES: Brazing: For zinc-based metals: Vee the broken edges to 45o.
[Show full text]
Metals Chart
Metals Chart The following chart gives you an overall concept of which metals can be plated with each kit, and the steps required. To read the chart, pick your base metal type (or current plating type) on the left, then pick the type of plating you want to do from along the top. For example, if you start with a piece of stainless steel, and want to chrome plate it with Copy Chrome, the steps are: 1.Degreaser until it passes the waterbreak test 2.Use Pickle #4 to etch 3.Strike Coat with Flash Copper 4.Nickel Plate (The Copy Chrome Column says "Over Nickel") 5.Copy Chrome Plate Some Notes: -Gold Plating (not shown) should only go over a nickel or tin plate. -Silver Plating (not shown) should only go over a copper, nickel or tin plate. -Hard Chrome Plating (not shown) is usually plated directly over steel parts, or zincated aluminum This chart can also be used to assist with brush plating, however you cannot brush plate over zincated aluminum or conductive painted materials. You should tank plate these materials with copper first, then you can brush plate over the copper. Bright Sp Etch Flash Copy Chrome/ Anodize Zinc Copy Black Bronze / Base Metal Strike Coat Acid Nickel Tin Degreaser (Pickle) Copper Chrome Repochrome Aluminum Cad Krome Brass Copper See Until Pass Deox- Zincate Then Over Over Over Over Over Nickel or Over Over Aluminum Over Nickel Anodizing Waterbreak Desmut Flash Copper Zincate Zincate Copper Nickel Zincate Copper Copper Zincate Section Nickel or Until Pass #4 As Nickel or Flash Over Nickel or Iron Steel Direct Flash Direct
[Show full text]
All-State® Welding, Brazing and Soldering
All-State® Welding, Brazing and Soldering Solutions for maintenance, repair and fabrication Additional Resources from All-State® All-State on the Internet www.all-statewelding.com All-State Technical Help Line 1-800-372-2123 All-State Customer Service 1-800-362-7080 1-800-634-7548 (fax) All-State Selection Guide request ALS-0032 All-State Selector Wall Chart request ALS-0030 Prest-O-Lite Catalog request POL-20000 The information contained herein is based on data and information developed by All-State Welding, Brazing & Soldering Products (“Seller”), but is presented without guarantee or warranty and the Seller makes no recommendation for and disclaims any liability incurred from any use thereof, including without limitation, any use in a commercial process not controlled by the Seller, and any use in violation of applicable laws and regulations. THE SELLER MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, EXCEPT AS EXPRESSLY STATED IN SELLER’S SALES CONTRACT OR SALES ACKNOWLEDGEMENT FORM. All-Guard, All-Shield, All-State, AquaSafe, Brazaloy, Core-Cast, Duzall, DynaGrip, EasyGrind, Galvover, Glidearc, Green Blaster, Hard-Tuff, HS 2C, Heliarc, HS-7, HS-65W, HY-10, Jet Flux, Kore-Bide, Migmaster, Monoweld, Prest-O-Lite, Ni-Matrix, Roll-Matrix, Rubbon, Ruf-Kut, Sealcor, Shield-Free, Sil-Flo, Siltube, SmoothCote, SteelArc, Strongset, Stud Plus, Super 18HI, Super 275, Super 31, Super 4-60, Super Join-M, TOP, Torchweld, Trucote and Prest-O-Lite are regis- tered trademarks of The ESAB Group, Inc. Table Of Contents Product Type page Product Selection Guides ............................................
[Show full text]