Wheel Alignment and Headlamp Adjustment Mechanical Standard

Total Page:16

File Type:pdf, Size:1020Kb

Wheel Alignment and Headlamp Adjustment Mechanical Standard Jaguar Land Rover Manufacturing Equipment Engineering Standard Wheel Alignment and Headlamp Adjustment Mechanical Standard Approved for use in BIW No N/A Approved for use in T&F Yes 25/02/2019 Approved for use in Paint No N/A Wheel Alignment and Headlamp Advanced Manufacturing Adjustment Mechanical Date: Version: Engineering Standard Page 1 of 59 Standards, Controls & Joining Manufacturing Engineering JLR-MEES-IL-164-037 25/02/2019 V1.0 Uncontrolled when printed Jaguar Land Rover Manufacturing Equipment Engineering Standard Revision History Date Name Issue Change Description 25/02/2019 M Lishman V1.0 Final check before issue Wheel Alignment and Headlamp Advanced Manufacturing Adjustment Mechanical Date: Version: Engineering Standard Page 2 of 59 Standards, Controls & Joining Manufacturing Engineering JLR-MEES-IL-164-037 25/02/2019 V1.0 Uncontrolled when printed Jaguar Land Rover Manufacturing Equipment Engineering Standard Associated Standards Relevant United Kingdom (UK) and European Normalised standards, the JLR General Pan Project Rules and individual specific JLR standards shall be applied to the design, build and installation of all equipment. Controls standards refer to: • JLR DCP Standard Workbook; • JLR Ethernet Workbook; • Rockwell Project Workbook; Switching standard refer to: • JLR IFM Project Workbook. Drives information refer to: • JLR SEW Project Workbook. Guarding standards refer to: • JLR Mechanical Specification 22 – Machine Guarding and Access; • The Bosch Guarding Project Workbook. Pneumatic standards refer to: • Festo Project Workbook. The engineering specification should be sought from the responsible JLR facilities engineer For all other standards refer to applicable JLR Trim and Final Standards at the following web address: https://us.sso.covisint.com Wheel Alignment and Headlamp Advanced Manufacturing Adjustment Mechanical Date: Version: Engineering Standard Page 3 of 59 Standards, Controls & Joining Manufacturing Engineering JLR-MEES-IL-164-037 25/02/2019 V1.0 Uncontrolled when printed Jaguar Land Rover Manufacturing Equipment Engineering Standard Table of Contents 1 INTRODUCTION .................................................................................................................................................. 8 1.1 ACRONYMS AND ABBREVIATIONS ................................................................................................................................. 8 2 DESIGN GUIDELINES ......................................................................................................................................... 10 2.1 REGULATORY COMPLIANCE ....................................................................................................................................... 10 2.2 DESIGN STANDARDISATION ....................................................................................................................................... 11 3 DESIGN REQUIREMENTS .................................................................................................................................. 12 3.1 SYSTEM DESCRIPTION .............................................................................................................................................. 13 3.1.1 Functions ................................................................................................................................................... 13 3.1.2 System Boundary ...................................................................................................................................... 14 Interfaces .......................................................................................................................................................... 14 Constraints ........................................................................................................................................................ 15 3.1.3 Exclusions .................................................................................................................................................. 15 3.1.4 Sequence of operations ............................................................................................................................ 16 3.2 FUNCTIONAL DETAIL ................................................................................................................................................ 17 3.2.1 Common items .......................................................................................................................................... 17 Specifications .................................................................................................................................................... 17 Capacity ............................................................................................................................................................ 17 3.2.2 WAHA Pre-Test Area ................................................................................................................................. 18 Shake Down Ladders ......................................................................................................................................... 18 Safety Barriers .................................................................................................................................................. 19 Bollard............................................................................................................................................................... 20 3.2.3 Wheel Alignment ...................................................................................................................................... 21 Pit ...................................................................................................................................................................... 22 Centralising Unit ............................................................................................................................................... 22 Base Frame ....................................................................................................................................................... 28 Wheel Geometry Measuring Units ................................................................................................................... 29 Associate Working Platform ............................................................................................................................. 29 Steering Wheel Balancer (SWB) ........................................................................................................................ 35 Traffic Light System........................................................................................................................................... 36 Communication System .................................................................................................................................... 36 3.2.4 Headlamp Alignment ................................................................................................................................ 37 Lightbox ............................................................................................................................................................ 38 Overhead Gantry .............................................................................................................................................. 39 Semi-automatic screwdrivers ........................................................................................................................... 40 Associate screen ............................................................................................................................................... 41 3.2.5 Advanced Driver Assistance System (ADAS) ............................................................................................. 41 Corner Reflector ............................................................................................................................................... 42 Front Target Board............................................................................................................................................ 45 Wheel Alignment and Headlamp Advanced Manufacturing Adjustment Mechanical Date: Version: Engineering Standard Page 4 of 59 Standards, Controls & Joining Manufacturing Engineering JLR-MEES-IL-164-037 25/02/2019 V1.0 Uncontrolled when printed Jaguar Land Rover Manufacturing Equipment Engineering Standard 3.2.6 Calibration System .................................................................................................................................... 46 Static Calibration Frame ................................................................................................................................... 48 SWB Calibration Frame ..................................................................................................................................... 50 Weight measurement calibration ..................................................................................................................... 51 Dynamic Calibration Unit – Rolling Master ....................................................................................................... 51 Calibration Frame Storage ................................................................................................................................ 52 Process function ..............................................................................................................................................
Recommended publications
  • Designed for Speed : Three Automobiles by Ferrari
    Designed for speed : three automobiles by Ferrari Date 1993 Publisher The Museum of Modern Art Exhibition URL www.moma.org/calendar/exhibitions/411 The Museum of Modern Art's exhibition history— from our founding in 1929 to the present—is available online. It includes exhibition catalogues, primary documents, installation views, and an index of participating artists. MoMA © 2017 The Museum of Modern Art * - . i . ' ' y ' . Designed for Speed: Three Automobiles by Ferrari k \ ' . r- ; / THE MUSEUM OF MODERN ART, NEW YORK The nearer the automobile approaches its utilitarian ends, the more beautiful it becomes. That is, when the vertical lines (which contrary to its purpose) dominated at its debut, it was ugly, and people kept buying horses. Cars were known as "horseless carriages." The necessity of speed lowered and elongated the car so that the horizontal lines, balanced by the curves, dominated: it became a perfect whole, logically organized for its purpose, and it was beautiful. —Fernand Leger "Aesthetics of the Machine: The Manufactured Object, The Artisan, and the Artist," 1924 M Migh-performance sports and racing cars represent some of the ultimate achievements of one of the world's largest industries. Few objects inspire such longing and acute fascination. As the French critic and theorist Roland Barthes observed, "I think that cars today are almost the exact equiv alent of the great Gothic cathedrals: I mean the supreme creation of an era, conceived with passion by unknown artists, and consumed in image if not in usage by a whole population which appropriates them as a purely magical object." Unlike most machines, which often seem to have an antagonistic relationship with people, these are intentionally designed for improved handling, and the refinement of the association between man and machine.
    [Show full text]
  • Laboratory Test Procedure for Fmvss 110T-01
    TP-110T-01 December 15, 2005 U.S. DEPARTMENT OF TRANSPORTATION NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION LABORATORY TEST PROCEDURE FOR FMVSS 110 Tire Selection and Rims for Motor Vehicles With a GVWR of 4,536 Kilograms or Less (For Light Truck Type Vehicles Only) ENFORCEMENT Office of Vehicle Safety Compliance Room 6111, NVS-220 400 Seventh Street, SW Washington, DC 20590 OVSC LABORATORY TEST PROCEDURE NO. 110T TABLE OF CONTENTS PAGE 1. PURPOSE AND APPLICATION................................................................... 1 2. GENERAL REQUIREMENTS....................................................................... 2 3. SECURITY ................................................................................................... 3 4. GOOD HOUSEKEEPING............................................................................. 3 5. TEST SCHEDULING AND MONITORING ................................................... 3 6. TEST DATA DISPOSITION.......................................................................... 3 7. GOVERNMENT FURNISHED PROPERTY (GFP)....................................... 4 8. CALIBRATION OF TEST INSTRUMENTS................................................... 4 9. PHOTOGRAPHIC DOCUMENTATION........................................................ 6 10. DEFINITIONS............................................................................................... 6 11. PRETEST REQUIREMENTS ....................................................................... 8 12. COMPLIANCE TEST EXECUTION.............................................................
    [Show full text]
  • 2020 Transit Connect Specs
    2020 Transit Connect Specs Use the menu to select and view information related to wheels, exterior colors and interior trim. Key product specifications include vehicle dimensions and capacities, detailed engine information, transmission gear ratios and more. 2020 Transit Connect Dimensions/ Weights/ Capacities Specs Gross Combination Weight Passenger Weight Accessory Reserve Capacity Rating (GCWR) (ARC) Calculation Passenger/ Cargo/ Fuel Gross Vehicle Weight (GVW) Capacity Base Curb Weight Gross Vehicle Weight Rating Payload Body Dimensions (GVWR) Tongue Weight Cargo Dimensions Maximum Payload Weight Rating Trailer Weight Gross Axle Weight Maximum Payload Weight Truck “Nominal Tonnage” Gross Axle Weight Rating Ratings (GAWR) Vehicle Class Ratings by Option Content Weight GVWR Gross Combination Weight (GCW) Option Weights Weight Distribution Passenger Dimensions Weight Ratings 2020 Transit Connect Body Dimensions Specs Dimensions/ Weights/ Capacities Inches (unless otherwise noted) Model Cargo Van SWB/LWB Passenger Wagon Description Overall Length 174.2/190.0 190.0 Wheelbase 104.8/120.6 120.6 Overall Width (with mirrors) 84.1/84.1 84.1 Overall Width (without mirrors) 72.2/72.2 72.2 Overall Height 72.0/72.0 71.6 Front Overhang 34.8/34.8 34.8 Rear Overhang 34.6/34.6 34.6 Front Track 61.4/61.4 61.4 Rear Track 61.7/61.7 61.7 Minimum Running Ground 5.4/5.6 5.7 Clearance Front Axle Clearance 7.0/7.1 7.0 Sliding Side Door Opening 44.4/44.4 37.6 Height(1) Sliding Side Door Opening 24.2/32.8 32.8 Width Rear Door Opening Height 47.3/45.5 45.4 Rear Door Opening Width 49.2/49.2 47.0 Loading Height at Rear Door 23.0/22.9 22.4 (curb) Turning Diameter (curb-to- 38.3/40.0 40.0 curb) (feet) (1) Wagon measured to 2nd-row seat in fold and dive position.
    [Show full text]
  • 2008-2009 Design and Fabrication of a SAE Baja Race Vehicle
    2008-2009 Design and Fabrication of a SAE Baja Race Vehicle A Major Qualifying Project Report Submitted to the Faculty of WORCESTER POLYTECHNIC INSTITUTE In partial fulfillment of the requirements for the Degree of Bachelor of Science By: ____________________________ Derek Britton ____________________________ Jessy Cusack ____________________________ Alex Forti ____________________________ Patrick Goodrich ____________________________ Zachary Lagadinos ____________________________ Benjamin Lessard ____________________________ Wayne Partington ____________________________ Ethan Wyman Date: April 29,2009 ____________________________ Kenneth Stafford, Advisor ____________________________ James Van De Ven, Advisor ____________________________ Torbjorn Bergstrom, Advisor 1 Table of Contents List of Figures ..................................................................................................................... 5 List of Tables ...................................................................................................................... 9 Introduction ....................................................................................................................... 10 Design Goals ..................................................................................................................... 11 Chassis .............................................................................................................................. 13 Ergonomics...................................................................................................................
    [Show full text]
  • Owner's Manual
    OWNER’S MANUAL The Best Protection For Your Journey™ MADE IN THE Hitch Ball U.S.A. Not Included 90-00-0600 - 600 lb. max tongue weight / 6,000 lb. max trailer weight 90-00-1000 - 1,000 lb. max tongue weight / 10,000 lb. max trailer weight 90-00-1200 - 1,200 lb. max tongue weight / 12,000 lb. max trailer weight 90-00-1400 - 1,400 lb. max tongue weight / 14,000 lb. max trailer weight ** Your model # can be found on the stickers on either spring arm. Make a note of it here for future reference ** DEALERS: PLEASE PASS THIS MANUAL ON TO THE END USER AFTER HITCH INSTALLATION. EqualizerHitch.com READ ENTIRE MANUAL BEFORE STARTING INSTALLATION Table of Contents Page Parts Breakdown . .4-5 Important Safety Information . 6 Important Hitch Information . .7 Step 1: Getting Things Ready . .8 Step 2: Install the Hitch Ball. 9 Step 3: Attach Hitch Head to Shank . 10 Step 4: Sway Bracket Assembly . 12 Step 5: Spring Arm Setup . 15 Step 6: Weight Distribution Setup . 16 Step 7: Weight Distribution Adjustments . 18 Step 8: Trailer Pitch Adjustment. 21 Step 9: Final Tightening . 22 Step 10: Regular Maintenance . 23 Service Tech Check List . 24 Appendix A: Troubleshooting Guide. 25 Customer Support . 26 Appendix B: Weight Distribution Adjustments . 27 Warranty . 29 TOOLS NEEDED FOR INSTALLATION The following tools will allow you to install the hitch properly: 1-1/8” Box-end wrench (Shank Bolts) 1-1/8” Socket wrench (Shank Bolts) 3/4” Box-end or socket wrench (Link Plates and L-brackets) 5/8” Socket or box-end wrench (Angle Set Bolt) Measuring tape Pencil Torque wrench capable of 320 ft-lbs of torque.
    [Show full text]
  • Honda Odyssey Specifications
    Honda Odyssey Specifications Engineering DESCRIPTION LX EX SE EX-L TOURING TOURING ELITE Engine Type: V-6 • • • • • • Engine Block / Cylinder Head: Aluminum-Alloy • • • • • • Horsepower (SAE net): 248 @ 5700 rpm • • • • • • Torque (SAE net): 250 lb-ft @ 4800 rpm • • • • • • Displacement: 3471 cc • • • • • • Redline: 6300 rpm • • • • • • Bore and Stroke: 89 mm x 93 mm • • • • • • Compression Ratio: 10.5 : 1 • • • • • • Valve Train: 24-Valve SOHC i-VTEC® • • • • • • Multi-Point Fuel Injection • • • • • • Drive-by-Wire Throttle System • • • • • • Eco Assist™ System • • • • • • Variable Cylinder Management™ (VCM®) • • • • • • Active Control Engine Mount System (ACM) • • • • • • Active Noise Cancellation™ (ANC) • • • • • • Direct Ignition System with Immobilizer • • • • • • 100K +/- Miles No Scheduled Tune-Ups1 • • • • • • CARB Emissions Rating2 : ULEV-2 • • • • • • Transmissions DESCRIPTION LX EX SE EX-L TOURING TOURING ELITE 6-Speed Automatic Transmission • • • • • • 6-Speed Automatic Transmission GEAR : RATIO 1st : 3.359 2nd : 2.095 3rd : 1.485 4th : 1.065 5th : 0.754 6th : 0.556 Reverse : 2.269 Final Drive : 4.250 Body / Suspension / Chassis DESCRIPTION LX EX SE EX-L TOURING TOURING ELITE Unit-Body Construction • • • • • • MacPherson Strut Front Suspension • • • • • • Multi-Link Double Wishbone Rear Suspension • • • • • • Electric Power-Assisted Rack-and-Pinion Steering (EPS) • • • • • • Stabilizer Bar (Front): 25.4 mm • • • • • • Steering Wheel Turns, Lock-to-Lock: 3.5 • • • • • • Steering Ratio: 16.4 • • • • • • Turning Diameter, Curb-to-Curb:
    [Show full text]
  • 2 Forward Vehicle Dynamics
    2 Forward Vehicle Dynamics Straight motion of an ideal rigid vehicle is the subject of this chapter. We ignore air friction and examine the load variation under the tires to determine the vehicle’s limits of acceleration, road grade, and kinematic capabilities. 2.1 Parked Car on a Level Road When a car is parked on level pavement, the normal force, Fz, under each of the front and rear wheels, Fz1 , Fz2 ,are 1 a F = mg 2 (2.1) z1 2 l 1 a F = mg 1 (2.2) z2 2 l where, a1 is the distance of the car’s mass center, C,fromthefrontaxle, a2 is the distance of C from the rear axle, and l is the wheel base. l = a1 + a2 (2.3) z a2 a1 x C 2Fz2 mg 2Fz1 FIGURE 2.1. A parked car on level pavement. 40 2. Forward Vehicle Dynamics Proof. Consider a longitudinally symmetrical car as shown in Figure 2.1. It can be modeled as a two-axel vehicle. A symmetric two-axel vehicle is equivalent to a rigid beam having two supports. The vertical force under the front and rear wheels can be determined using planar static equilibrium equations. Fz =0 (2.4) XMy =0 (2.5) Applying the equilibrium equationsX 2Fz +2Fz mg =0 (2.6) 1 2 − 2Fz a1 +2Fz a2 =0 (2.7) − 1 2 provide the reaction forces under the front and rear tires. 1 a2 Fz1 = mg 2 a1 + a2 1 a = mg 2 (2.8) 2 l 1 a1 Fz2 = mg 2 a1 + a2 1 a = mg 1 (2.9) 2 l Example 39 Reaction forces under wheels.
    [Show full text]
  • Installation Instructions
    READ ALL INSTRUCTIONS COMPLETELY AND THOROUGHLY UNDERSTAND THEM BEFORE DOING ANYTHING. CALL CHASSISWORKS TECH SUPPORT (916) 388-0288 IF YOU NEED ASSISTANCE. INSTALLATION AND TUNING GUIDE VAS 162MS-425 Bolt-In Front Coil-Over Conversion Double-Adjustable - QuickSet 2 Shock Mounting Specifi cations Mounting Total Compressed Extended Ride Height* Spring Part Number Valving Upper LowerTravel Length* Length* Min. Max. Length VAS 162MS-425 Double Spherical Stem Crossbar 4.25” 10.27” 14.52” 11.97” 12.82” 9” * Shock mounting lengths are measured from the chassis contact surface of upper stem to pivot center of crossbar. Add .20” to lengths if measuring to control arm contact surface of lower crossbar. 1 PARTS LIST Prior to beginning installation use the following parts lists to verify that you have received all components required for installation. VAS 162MS-425 - VariShock QuickSet 2 Coil-Overs Part Number Qty Description 8A24XAX-43CH 2 QuickSet 2 Coil-Over Shock, Upper Stem and Short Lower Poly Mounts 3173-09-20-32 2 Bumpstop 1-1/4” long 899-020-208 2 Ball-Stud Top Mount Hardware VAS 501-103 1 Spring Seat Set, Extended 3/4” 3102-056-18RC 2 Jam Nut 9/16-18 RH, Clear Zinc 899-061-304 1 Crossbar Hardware Bag 899-012-HEX7/64 1 Ball-End Driver 7/64” Hex Screw 899-020-208 - Ball-Stud Top Mount Hardware Part Number Qty Description 3117-063-18C 1 Half Locknut 5/8-18 Nylon Insert 3144-25-28-0 1 Grease Zerk 1/4-28 Straight 899-044.63-1.13 1 Washer .635” ID x 1.13” OD, Zinc-Plated Steel 899-044.70-1.25 1 Washer .695” ID x 1.25” OD, Zinc-Plated Steel 899-060-201
    [Show full text]
  • MY22 Sequoia Ebrochure
    2022 Sequoia Page 1 2022 SEQUOIA Room for everyone and everything. Whether you’re navigating through the urban jungle or traveling off the beaten path, the 2022 Toyota Sequoia is ready to turn every drive into an adventure. Three rows of seats let you bring up to eight, while its spacious interior and powerful 5.7L V8 engine let you load it up and haul even more, to make the most of the places you’ll go. Limited shown in Shoreline Blue Pearl. Cover image: See footnotes 1 and 2 for information on towing and roof payload. See numbered footnotes in Disclosures section. Page 2 INTERIOR In Sequoia, everyone gets to ride first class. Hear Comfort your music like never before with the available JBL®3 within reach. Premium Audio system, and let your rear-seat passengers catch up on their favorite movies with the available rear-seat Blu-ray Disc™ player. Platinum interior shown in Red Rock leather trim. Simulation shown. Heated and ventilated front seats Moonroof Three-zone climate control The available heated and ventilated front Let more of the outside in with Sequoia’s The driver, front passenger and rear seats found inside Sequoia Platinum give standard one-touch tilt/slide power passengers will be comfortable inside the driver and front passenger more comfort moonroof with sliding sunshade. Open Sequoia, thanks to its three-zone automatic and the option to warm up or cool down it up to let in some fresh air, brighten climate control in the front and rear of the with the touch of a button.
    [Show full text]
  • Installation of Body & Special Equipment
    Body Builders Guide I Body Builders Guide General Motors Isuzu Commercial Truck, LLC (GMICT) and American Isuzu Motors Inc. Is striving to provide you with the most up- to-date and accurate information possible. If you have any suggestion to improve the Body Builder's Guide, please call GMICT Application Engineering. In the West Coast call 1-562-229-5314 and in the East Coast call 1-404-257-3013 Notice of Rights All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means, electronic, mechanical, recording or otherwise, without the prior written permission. Notice of Liability All specifications contained in this Body Builders Guide are based on the latest product information available at the time of publication. The manufacturer reserves the right to discontinue or change at anytime without prior notice, any parts, material, colors, special equipment, specifications, designs and models. Made and printed in the USA. II Contents Introduction FMVSS EPA Requirements Weight Distribution Installation of Body & Special Equipment Glossary of Dimensions Clearances Weight Distribution Formulas Body Installations Recommended Weight Distribution Prohibited Attachment Areas Trailer Weight Subframe Mounting Performance Calculations Crew Cab Body/Frame Requirements Highway Limits Modification of the Frame Federal Bridge Formula Table Fluid Lines Electrical Wiring & Harnessing Commodity & Material Weights Maximum Allowable Current Approximate Weight of Commodites & Materials Exhaust System Fuel System Vehicle
    [Show full text]
  • Honda Quits F1! Japanese Manufacturer to Bring Curtain Down on Race-Winning Programme
    >> Britain’s Land Speed Record attempt update – see p36 December 2020 • Vol 30 No 12 • www.racecar-engineering.com • UK £5.95 • US $14.50 Honda quits F1! Japanese manufacturer to bring curtain down on race-winning programme CASH CONTROL We reveal the details of Formula 1’s Concorde deal SAFETY CELL The latest in composite chassis technology design INDYCAR SCREEN Aerodine on building US single seater safety device VIRTUAL TRADE Exciting new engineering products for the 2021 season 01 REV30N12_Cover_Honda-ACbs.indd 1 19/10/2020 12:56 THE EVOLUTION IN FLUID HORSEPOWER ™ ™ XRP® ProPLUS RaceHose and ™ XRP® Race Crimp Hose Ends A full PTFE smooth-bore hose, manufactured using a patented process that creates convolutions only on the outside of the tube wall, where they belong for increased flexibility, not on the inside where they can impede flow. This smooth-bore race hose and crimp-on hose end system is sized to compete directly with convoluted hose on both inside diameter and weight while allowing for a tighter bend radius and greater flow per size. Ten sizes from -4 PLUS through -20. Additional "PLUS" sizes allow for even larger inside hose diameters as an option. CRIMP COLLARS Two styles allow XRP NEW XRP RACE CRIMP HOSE ENDS™ Race Crimp Hose Ends™ to be used on the ProPLUS Black is “in” and it is our standard color; Race Hose™, Stainless braided CPE race hose, XR- Blue and Super Nickel are options. Hundreds of styles are available. 31 Black Nylon braided CPE hose and some Bent tube fixed, double O-Ring sealed swivels and ORB ends.
    [Show full text]
  • Ground Vehicle Standard for Ambulances V.1.0 Edition
    TAT ION O D I F R E A M CC B A U L N A O N C N E O I S S E S R I V M I C M E O S C Ground Vehicle Standard for Ambulances v.1.0 Edition Established and Maintained by CAAS The Commission on Accreditation of Ambulance Services www.caas.org CAAS GVS v.1.0 Acknowledgements The following groups & individuals participated as the Steering Committee for the GVS v.1.0: PROJECT TEAM Commission on Accreditation of Ambulance Services (CAAS) Mark Meijer (Chair, CAAS) Mark Postma (Vice Chair, CAAS; GVS v.1.0 Project Co-Chair) Joe Penner Dale Berry (Alternate) Sarah McEntee, EMT-P (Executive Director) Marcie McGlynn (Staff) Association and Society Management International (ASMI) Ian Weston, MPP, QAS, EMT (GVS v.1.0 Project Manager) ORGANIZATIONAL STAKEHOLDER LIASIONS Ambulance Manufacturers Division (AMD) National Association of EMTs (NAEMT) Mark Van Arnam (GVS v.1.0 Project Co-Chair) Skip Kirkwood, MS, JD, EMT-P, EFO, CEMSO Alain Brunelle (Alternate) Don Lundy, BHS, NREMT-P (Alternate) American Ambulance Association (AAA) National Association of State EMS Officials (NASEMSO) Ron Thackery, JD Michael Berg, BS, NRP Mike Hall (Alternate) Dia Gainor (Alternate) American College of Emergency Physicians (ACEP) National EMS Management Association (NEMSMA) Sabina Braithwaite, MD, MPH, NREMT-P Aarron Reinert, BA, NREMT-P Troy Hagen, MBA (Alternate) Association of Air Medical Services (AAMS) Rick Sherlock National Volunteer Fire Council (NVFC) Elena Sierra (Alternate) Ken Knipper Joe Maruca (Alternate) National Association of EMS Physicians (NAEMSP) Brent Myers, MD, MPH Transportation Research Board (TRB) Lynn White, MS (Alternate) Bernardo Kleiner GOVERNMENT AGENCY LIAISONS (NON-VOTING) U.S.
    [Show full text]