DOCSLIB.ORG

Speed Control of Universal Motor Using Sniversal Bridge Mr

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Speed Control of Universal Motor Using Sniversal Bridge Mr NOVATEUR PUBLICATIONS INTERNATIONAL JOURNAL OF INNOVATIONS IN ENGINEERING RESEARCH AND TECHNOLOGY [IJIERT] ISSN: 2394-3696 VOLUME 5, ISSUE 4, Apr-2018 SPEED CONTROL OF UNIVERSAL MOTOR USING SNIVERSAL BRIDGE MR. P. P. KULKARNI Electrical Department, Sanjeevan Engineering Institute and Technology, Panhala, Kolhapur. India. BARALE RENU Electrical Department, Sanjeevan Engineering Institute and Technology, Panhala, Kolhapur. India. POTE TEJASHREE Electrical Department, Sanjeevan Engineering Institute and Technology, Panhala, Kolhapur. India. SUTAR KOMAL Electrical Department, Sanjeevan Engineering Institute and Technology, Panhala, Kolhapur. India. POWAR VAISHALI Electrical Department, Sanjeevan Engineering Institute and Technology, Panhala, Kolhapur. India. ABSTRACT Speed control of AC and DC motor is carried out by using universal bridge drive. This universal Bridge which consist combination of IGBT & MOSFET and Diodes by changing the gate pulses. This universal Bridge is controlled by V/F control method. This method is used for single phase AC and DC motor control with small modification in hardware and software using Simulink. Power circuit includes inverter which connected to PWM generator. There are many industrial and domestic applications were speed variation is required, many speed control techniques are used like rheostat control, variable voltage control, v/f control. The simulation is carried out in MATLAB. The characteristics of motors can be studied from waveform obtained by simulation. INTRODUCTION In electrical drives we have various speed control methods to control speed of 1ᴓ and 3ᴓ AC and DC motors. For speed controlling of motors we use separate bridge circuits such as rectifier and inverter circuit which include power electronic devices. The rectifier circuit controls speed of AC motor and inverter circuit controls speed of DC motor. To overcome this problem we have created a single bridge which acts as rectifier as well as inverter and controls speed of AC as well as DC motor. This single bridge circuit includes combination of MOSFET’s and SCR’s, where MOSFET’s are voltage controlling devices hence this are used to form inverter bridge circuit and SCR’s are current controlling devices hence this are used to form rectifier bridge circuit. Fig.1. Block Diagram 22 | P a g e NOVATEUR PUBLICATIONS INTERNATIONAL JOURNAL OF INNOVATIONS IN ENGINEERING RESEARCH AND TECHNOLOGY [IJIERT] ISSN: 2394-3696 VOLUME 5, ISSUE 4, Apr-2018 I. HARDWARE IMPLEMENTATION A. POWER SUPPLY CIRCUIT Smoothing Regulator Transformer Rectifier Fig.2. Block Diagram of power supply The power supply circuit consists of step down transformer 230/12V which is passed through single phase bridge rectifier. The rectifier converts the alternating current (AC to DC) and capacitor filters are used for smoothing out the DC. The above fig. shows the block diagram of power supply circuit. B. CONTROL CIRCUIT The control circuit consists of microcontroller-Arduino Pro Mini w/ATMega328, MOSFET’s and SCR’s and circuit is controlled by gate signal. The microcontroller circuit requires +5V DC supply. The 12 V from the 230/12V step down transformer is rectified and a constant voltage of 5V DC is obtained with the help of voltage regulator. The switching schemes to the metal oxide semiconductor field effect transistor (MOSFET)are generated by microcontroller. This microchip is controller circuit that is used to generate the modulated and carrier signal for the inverter. For generation of modulating output for inverter the zero crossing detector (ZCD). The schematic of the control circuit is, Fig.3. MOSFET Driver Fig.4. SCR Driver 23 | P a g e NOVATEUR PUBLICATIONS INTERNATIONAL JOURNAL OF INNOVATIONS IN ENGINEERING RESEARCH AND TECHNOLOGY [IJIERT] ISSN: 2394-3696 VOLUME 5, ISSUE 4, Apr-2018 C. DRIVER CIRCUIT The driver circuit consists of universal bridge which consists combination of MOSFET’s, SCR’s driving the gate signal. The driver consists of optocoupler-4N33 which isolates electrical signals. The driver also consists of IC-IR211D which acts as gate drive. The below fig, shows schematic of driver circuit, Fig.5. Diver Circuit D. MICROCONTROLLER (Ardunio Pro Mini ATmega w/328) Fig.6 Pin digram of ArdunioProMini The Ardunio Pro is microcontroller board based on the ATmega328. The Pro comes in 5V/16MHz. It has 14 digit input/output pins, 6 analog inputs, a battery power jack, a power switch, a rest button, and holes for mounting a power jack, an ICSP header, and pin headers. A six pin header can be connected to an FIDI cable or Sparkfun breakout to provide USB power and communication to the board. The Ardunio Pro is intended for semi-permanent installation in objects or exhibitions. The board comes without pre-mounted headers, allowing the use of various types of connectors or direct soldering of wires. The pin layout is compatible with Ardunio shields. II. RESULT The following tests was conducted in laboratory. 1. DC motor load was connected at the output of inverter and speed was varied by using variable pot. Input voltage 230V AC, Output Voltage 230V, DC motor rating:-230V, 11A, 1500 RPM, 3HP. The variation of speed with armature current is shown in bellow graph: 24 | P a g e NOVATEUR PUBLICATIONS INTERNATIONAL JOURNAL OF INNOVATIONS IN ENGINEERING RESEARCH AND TECHNOLOGY [IJIERT] ISSN: 2394-3696 VOLUME 5, ISSUE 4, Apr-2018 Speed VS Armature Current (DC motor) 120% 100% 80% 60% 40% Speed in % in Speed 20% 0% 2 4 6 8 10 Armature Current Ia Fig.7 Waveform across load at different values of armature current. 2. A Fan load was connected at the output of inverter and speed was varied by using variable pot. Input voltage 230V AC, Output voltage 230V, Induction motor rating:-230V, 1250RPM, 1A, 55W. The variation of speed with current is shown in bellow graph: Speed VS Current (AC motor) 120% 100% 80% 60% 40% Speed in % in Speed 20% 0% 0.2 0.5 0.6 0.7 1 Current in Ampere Fig.7 Waveform across load at different values of current III. CONCLUSION This paper presents variable frequency drive to control the speed of 1ᴓ and 3ᴓ AC and DC motor. The main aim this project is to create a universal control board through which controlled a single or three phase AC and DC motor, with slight software and hardware modification. This universal board can hence used for different kinds of laboratory applications. The designed system was successfully fabricated and tested in the laboratory. AKNOWLADGEMENT The authors are truly grateful to Mr.P.P. Kulkarni and Mr N.S. Jadhav sir for their valuable suggestions in reviewing the manuscript. REFERENCES JOURNAL PAPERS (1) Ranjit Kumar Bindal1,Amandeep Kaur2.Speed Control Of Induction Motor Drive Using Universal Bridge, International Journal for Research in applied Science & Engineering Technology. BOOKS (1) M. H. Rashid, Power electronics (circuits, devices and applications). 25 | P a g e NOVATEUR PUBLICATIONS INTERNATIONAL JOURNAL OF INNOVATIONS IN ENGINEERING RESEARCH AND TECHNOLOGY [IJIERT] ISSN: 2394-3696 VOLUME 5, ISSUE 4, Apr-2018 THESES I. Ismail, S.Taib, A.R Mohdsaad, M. Isa and I, Daut,”Development of control circuit for single phase inverter using Atmel Microcontroller,” II. Thida Win, Nang Sabai, and Hnin Nandar Maung, “Analysis of variable frequency three phase induction motor drive”. III. Mohd Fakhizan bin Ramie, Mohammad Fadhil Pesol, and Khaisul Nisak Md has an, “PWM technique to control speed of induction motor using MATLAB”. IV. Rodolfo Enchilada, Sergio Horta, Marco Oliver, has, “A three phase motor drive using IGBT/MOSFET and constant V/F speed control with slip regulation”.3 26 | P a g e .
Load more

Recommended publications
  • POWER ELECTRONICS TRAINER (Model : XPO-PE) / MICROCONTROLLER BASED PE (Model : XPO-Μc LSPT)
    POWER ELECTRONICS TRAINER (Model : XPO-PE) / MICROCONTROLLER BASED PE (Model : XPO-µC LSPT) SALIENT FEATURES u Aesthetically designed injection molded electronic desk. u Master unit carrying useful experiment resources like line Synchronized firing circuits, Power supplies, lamp load, RLC loads, Battery charging supply etc. while the central slot will hold replaceable experiment panels. u Each multi experiment panel is secured in an ABS molded plastic sturdy enclosure, and has colorful screw less overlay showing circuit & Connection through Sturdy 4mm Banana Sockets & Patch Chords. u Set of User Guide provided with each unit. u Order 6 Master units and set of 6 panels (PE 1 x 2 , PE2, PE3, PE6X2nos)+ Power scope, buy more of PE1 and PE6 being major panels. Master Unit Accessories: Built in power supply l 15 pin D connector cable assembly, u DC supply : + 12V, 500mA, l 4mm patchcords : 100mm X 10 Nos & 500mm X 20 Nos. u Unregulated Power supply 17V / 750mA, Optional Power Scope u Regulated 7VDC to 14VDC/3A O/P is provided as 12V Battery charging supply. In absence of battery, same may be used as simulated battery source to run experiments on inverters etc. u Isolated DC supply +12V/ 300mA with isolated common. u On board Inverter transformer of Primary & Secondaries: 12-11-0- 11-12/3A. u On board o/p to Isolated Drive Circuit AC supply u 230V AC line voltage is made available on two banana 4mm Accessory for any Lab CRO for off ground differential measurements sockets as well as 1.5A fuse extender for variac if used.
    [Show full text]
  • Universal Motor - Construction, Working and Characteristics
    Universal Motor - construction, working and characteristics. A universal motor is a special type of motor which is designed to run on either DC or single phase AC supply. These motors are generally series wound (armature and field winding are in series), and hence produce high starting torque (See characteristics of DC motors here). That is why, universal motors generally comes built into the device they are meant to drive. Most of the universal motors are designed to operate at higher speeds, exceeding 3500 RPM. They run at lower speed on AC supply than they run on DC supply of same voltage, due to the reactance voltage drop which is present in AC and not in DC. There are two basic types of universal motor : (i)compensated type and (ii) uncompensated type. Construction of Universal motor Construction of a universal motor is very similar to the construction of a DC machine. It consists of a stator on which field poles are mounted. Field coils are wound on the field poles. However, the whole magnetic path (stator field circuit and also armature) is laminated. Lamination is necessary to minimize the eddy currents which induce while operating on AC. The rotary armature is of wound type having straight or skewed slots and commutator with brushes resting on it. The commutation on AC is poorer than that for DC. because of the current induced in the armature coils. For that reason brushes used are having high resistance. Working of universal motor A universal motor works on either DC or single phase AC supply. When the universal motor is fed with a DC supply, it works as a DC series motor.
    [Show full text]
  • UNIVERSAL MOTORS Universal Motor
    UNIVERSAL MOTORS Universal motor The motors which can be used with a single phase AC source as well as a DC source of supply and voltages are called as Universal Motor. It is also known as Single Phase Series Motor. A universal motor is a commutation type motor. Construction of the universal motor The construction of the universal motor is same as that of the series motor. I n o rd e r t o m i n i m i z e t h e p ro b l e m o f commutation, high resistance brushes with increased brush area are used. To reduce Eddy current losses the stator core and yoke are laminated. The Universal motor is simple and less costly. It is used usually for rating not greater than 7 5 0 W . Characteristic of Universal motor The characteristic of Universal motor is similar to that of the DC series motor. When operating from an AC supply, the series motor develops less torque. By interchanging connections of the fields with respect to the armature, the direction of rotation can be altered. Universal motor T h e d i r e c t i o n o f t h e developed torque will re m a i n p o s i t i v e , a n d direction of the rotation will be as it was before. The nature of the torque will be pulsating, and the frequency will be twice that of line frequency as shown in the waveform. Universal motor Thus, a Universal motor can work on both AC and DC.
    [Show full text]
  • Design and Simulation of Leakage Current in Smart Power Module (Spm) Motor Drive Application
    View metadata, citation and similar papers at core.ac.uk brought to you by CORE provided by UTHM Institutional Repository DESIGN AND SIMULATION OF LEAKAGE CURRENT IN SMART POWER MODULE (SPM) MOTOR DRIVE APPLICATION SYAHFITRI BIN SAIDIN A project report submitted in partial fulfillment of the requirement for the award of the Degree of Master of Electrical Engineering Faculty Of Electrical And Electronics Engineering Universiti Tun Hussein Onn Malaysia DECEMBER 2013 vi CONTENTS TITLE i DECLARATION ii DEDICATION iii ACKNOWLEDGEMENT iv ABSTRACT v CONTENTS vi LIST OF FIGURES x LIST OF TABLES xiv LIST OF SYMBOL AND ABBREAVIATION xv LIST OF APPENDIXES xvi CHAPTER 1 INTRODUCTION 1.1 General Background of Electric Motor 1 1.2 Universal Motor 3 1.2.1 Properties of Universal Motor 4 1.2.2 Applications of Universal Motor 6 1.3 DC Motor 7 1.3.1 Brush DC Motor 8 1.3.2 Brushless DC Motor 9 1.3.3 Permanent Magnet Stators 9 1.4 Smart Power Module (SPM) 10 1.5 Problem Statement 12 vii 1.6 Objectives and Scopes 1.6.1 Objective 13 1.6.2 Scope of Work 14 1.6.3 Thesis Overview 14 CHAPTER 2 LITERATURE REVIEW 2.1 Introduction 16 2.2 What Is Leakage Current? 16 2.2.1 Why Is It Important? 17 2.2.2 What Causes Leakage Current? 17 2.2.3 What Is A Safe Level 18 2.3 Direct Current Motor (Dc Motor) 19 2.3.1 Principle Of Dc Motor 19 2.3.2 Detailed Description Of A Dc Motor 21 2.3.3 Working Or Operating Principle Of Dc Motor 23 2.3.4 Construction Of Dc Motor 28 2.3.5 Permanent Magnet Stators 29 2.3.6 Electrical Connections Between The Stator And Rotor 30 2.4 Electricity Consumption By Electrical Motor Systems 31 2.5 Motor Efficiency 33 2.6 Brushless DC Motors (BLDC) 35 2.6.1 Brushless Vs.
    [Show full text]
  • Brush DC Motor Runs Along Dan Jones, Incremotion Associates
    TECHNICAL Brush DC Motor Runs Along Dan Jones, Incremotion Associates Everything started in 1800 when Volta developed the first DC battery. Fara- day used the DC battery to develop the first electric motor. It used brushes to transfer the battery voltage and cur- rent to the rotating disk rotor. This was in mid-1831. Thus was born the brush DC motor. Construction The slotted brush DC motor of today comes in two basic configurations: the wound field DC motor and the perma- nent magnet DC motor. The key parts of a DC motor include the armature (the rotating part), the field (either a cop- per winding or permanent magnet), and a mechanical commutation sys- tem consisting of a slotted commutator, mechanical brushes with copper wires connecting to outside terminals. The commutator is connected to various windings in a sequential pattern. The two brushes ride on the commutator to connect to the battery or outside power source via the terminals as shown in Figure 1. These brush DC motor types are called slotted or iron core types. Motor Operation The DC motor is the simplest motor type. Raise the input voltage and the motor speeds up. Lower the voltage and it reduces speed. Increase the mo- tor’s shaft load and shaft torque and armature current go up while the speed goes down. The permanent magnet DC motor is the most popular type, replac- ing the three wound field DC motors in many applications. Today the most Figure 1 Permanent magnet DC motor structure. popular wound field DC motor has an- other name—the universal motor—a separate motor type because it can be driven by AC and DC input power.
    [Show full text]
  • AN422 Improved Universal Motor Drive
    ® APPLICATION NOTE Improved Universal Motor Drive JM. BOURGEOIS, JM. CHARRETON, P. RAULT INTRODUCTION Universal motors are mostly operated in AC current mode and are controlled by means of TRIACS. This widespread solution leads to a cheap electronic controller board but has some drawbacks. In particular the high peak to peak current gives poor motor efficiency and the consequential high brush temperature leads to limited motor lifetime. When operating in DC mode, significant improvements are obtained. The RMS and peak to peak current of the motor are smaller, reducing Iron losses and brush temperature. Operating in DC mode enables shrinking of the motor size, and increasing the motor lifetime. Furthermore, magnetic constriction of motor core and torque ripple decrease; the 100Hz noise is further reduced. This technical note presents three solutions for motor operation in AC and DC mode, based on phase control. Motor current and motor efficiency are compared in AC and DC mode. Component selection is proposed for each case, enabling the design of a cost effective solution. AN422 / 02,94 IMPROVED UNIVERSAL MOTOR DRIVE 1 CIRCUIT TOPOLOGIES Three different topologies for control of universal motors are shown in figures 1a, 1b, 1c: - a conventional AC drive using a TRIAC - a DC drive using a TRIAC and a rectifier bridge - a DC drive using an IGBT and a rectifier bridge Each is controlled with a low cost microcontroller, ST6. The difference between the control software concerns the output signal of the microcontroller, which is either adapted to TRIACs or to IGBTs. A and B topologies are operated with a "SNUBBERLESS" TRIAC.
    [Show full text]
  • Multiple Choice Practice Questions for ONLINE/OMR AITT-2020 2 Year
    Multiple Choice Practice Questions for ONLINE/OMR AITT-2020 nd 2 Year Electrician Trade Theory DC machine (Generator & Motor) 1 What is the name of the part marked as ‘X’ in DC generator given below? A - Armature core B -Brush C- Commutator raiser D -Commutator segment 2 What is the name of D.C generator given below? A- Differential long shunt compound B- Differential short shunt compound C -Cumulative long shunt compound D -Cumulative short shunt compound 3 Which rule is used to find the direction of induced emf in D.C generator? A- Cork screw rule B -Right hand palm rule C -Fleming’s left-hand rule D -Fleming’s right hand rule 4 Which formula is used to calculate the generated emf in D.C generator? A –ZNPa/60ɸ B -ɸZna/60P C - ɸZnp/60a D - ɸZnp/60 5 What is the formula to calculate back emf of a D.C motor? A -Eb = V/Ia Ra B- Eb = V x Ia Ra C -Eb = V – Ia Ra D -Eb = V + Ia Ra 6 What is the name of the part marked ‘X’ in DC generator given below? A -Pole tip B -Pole coil C -Pole core D -Pole shoe 7 What is the name of the D.C generator given below? A -Shunt generator B -Series generator C- Compound generator D -Separately excited generator 8 Which energy is converted into electrical energy by generator? A -Heat B- Kinetic C -Chemical D -Mechanical 9 What is the name of D.C generator field given below? A -Short shunt compound generator B -Long shunt compound generator C -Differential compound generator D -Cumulative compound generator 10 What is the principle of D.C generator? A -Cork screw rule B -Fleming’s left-hand rule C -Fleming’s
    [Show full text]
  • Electric Motor
    ELECTRIC MOTOR Electric motors of various sizes. An electric motor converts electrical energy into mechanical motion. Device references The reverse task, that of converting mechanical motion into electrical energy, is accomplished by a generator or dynamo. In many cases the two devices differ only in their application and minor construction details, and some applications use a single device to fill both roles. For example, traction motorsused on locomotives often perform both tasks if the locomotive is equipped with dynamic brakes. Principle of operation Rotating magnetic field as a sum of magnetic vectors from 3 phase coils. Most electric motors work by electromagnetism, but motors based on other electromechanical phenomena, such as electrostatic forces and the piezoelectric effect, also exist. The fundamental principle upon which electromagnetic motors are based is that there is a mechanical force on any wire when it is conducting electricity while contained within a magnetic field. The force is described by the Lorentz force law and is perpendicular to both the wire and the magnetic field. Most magnetic motors are rotary, but linear types also exist. In a rotary motor, the rotating part (usually on the inside) is called the rotor, and the stationary part is called the stator. The rotor rotates because the wires and magnetic field are arranged so that a torque is developed about the rotor's axis. The motor containselectromagnets that are wound on a frame. Though this frame is often called the armature, that term is often erroneously applied. Correctly, the armature is that part of the motor across which the input voltage is supplied.
    [Show full text]
  • Bodine Electric Gearmotor Handbook
    Courtesy of Steven Engineering, Inc - (800) 258-9200 - [email protected] - www.stevenengineering.com For up-to-date product information, 2D/3D CAD drawings and detailed specifications, please visit www.bodine-electric.com About Us Bodine Electric Company offers over 1,200 standard products, and thousands of custom designed fractional horsepower (<746 Watts) gearmotors, motors and motion controls (fixed and variable speed AC, brushless DC, and permanent magnet DC). Bodine products are available via an extensive distributor network or sold directly to OEMs. Known for their reliability, long life and competitive prices, Bodine gearmotors and motors are designed for demanding industrial and commercial applications such as medical devices, scientific and laboratory equipment, labeling equipment, printing presses, packaging equipment, factory automation, and mobile and solar powered equipment. Bodine Electric is headquartered in Northfield, Illinois (20 miles north of Chicago) with manufacturing and assembly operations in Peosta, Iowa, U.S.A. Our quality management system is certified to ISO 9001:2008. MANAG Bodine Electric Company ITY GEE LLI M A EE UU NN 201 Northfield Road QQ TT D D SS EE I Y I Y F F Northfield, Illinois 60093 U.S.A. S S I I T T T T E E R R ISO M M E ISO E C www.bodine-electric.com C 9001:2008 [email protected] Phone: 773.478.3515 Copyright Notice: Small Gearmotors, Motors, and Controls Handbook ©2016 Bodine Electric Company. All rights reserved. Unauthorized duplication, distribution, or modification of this publication, in part or whole, is expressly prohibited. ISBN 9994675133. Library of Congress Catalog Number 92-076079.
    [Show full text]
  • AC Motor Speed Control and Other Motors
    AC Motor Speed Control AC Induction Motor Speed Control ►So what can we do to control the speed of an AC induction motor? Change the number of poles (in discrete increments - inefficient & rarely done) Change the frequency of the AC signal Change the slip Change AC Frequency ►Variable speed AC Motor adjustable speed drives are known as inverters, variable frequency drives (VFD) , or adjustable speed drives (ASD). ►Common ways to vary AC frequency: Six-step inverter Pulse-Width-Modulation Vector Flux Six-step Inverter ►AC rectified to DC, then switched to imitate a sine wave also called a Variable Voltage Inverter or VVI Pulse-Width-Modulation ►DC voltage (rectified AC) rapidly switched to match "area under curve" also called Pulse-Density-Modulation Changing Rotor Slip ►Important to match the motor to the load ensure that a change in motor power gives a desired change in load speed ►Load should have a substantial inertial components inertial torque can "carry" the load through brief periods when motor torque cannot ►Best used with motors designed for high slip Variable Series Resistance ►Additional series resistance reduces voltage across main windings Variable Resistor Main AC winding Rotor “The traditional way to control the speed of a wound rotor induction motor is to increase the slip by adding resistance in the rotor circuit. “ http://www.findarticles.com/p/articles/mi_m3541/is_3_77/ai_98551731 Variable Voltage Transformer ►More efficient than previous method, no power wasted in the series resistance Variable Transformer
    [Show full text]
  • BVRIT HYDERABAD College of Engineering for Women Department of Electrical and Electronics Engineering
    BVRIT HYDERABAD College of Engineering for Women Department of Electrical and Electronics Engineering Hand Out Subject Name: Electrical Machine-III Prepared by (Faculty(s) Name): Babita Gupta, Assistant Professor, EEE Year and Sem, Department: III Year- I Sem, EEE Unit – I: synchronous Machines & characteristics Important Points / Definitions: Synchronous machine is know as doubly excited machine. Synchronous machines can be operated as either generators or motors., The main parts of a synchronous machine are identified: rotor (field); stator (armature); prime mover ; exciter. An alternator which converts mechanical energy from a prime mover to AC electric power at specific voltage and frequency. It is also known as synchronous generator. The alternator work on the principle of faraday’s law of electromagnetic induction. The direction of the induced current can be determined by Flemming's right-hand rule. The armature winding in an alternator either open & closed type. Closed winding forms star connection in an alternator. There are different types of armature winding used in alternator. 1. Single phase and poly phase armature winding. 2.Concentrated winding and distributed winding 3.Full pitch coil winding and short pitch coil winding. 4.Intergral winding and fractional slot winding. There are two types of rotors in an alternator:- 1. Salient pole type. 2. Smooth cylindrical type. The e.m.f equation of an alternator is Eph= 4.44fΦTphKcKd volts Synchronous generator always runs at synchronous speed i.e Ns = 120f/P. Harmonics which are generated in the e.m.f due to slotting is called slot harmonics. Different ways to eliminate the harmonics from generated voltage: 1.
    [Show full text]
  • Markon Alternators
    Application Guidance Notes: Technical Information from Cummins Generator Technologies AGN 102 - Markon Alternators ANNOUNCEMENT Markon alternators are no longer manufactured. This Applications Guidance Note provides information for customers who are still operating the 2-pole single-phase alternators. DESCRIPTION The small Markon 2-pole alternators are designed for simple applications and, as such, have quite basic excitation systems - although not always simple to understand - which are designed to be rugged and reliable rather than sophisticated. The remit during the design / development stage was 'keep it simple and reliable' yet able to cope as well as any other alternator sold into this small machine sector. MARKON ALTERNATOR TYPES Marcon has a long history of alternator manufacturing and many models and variations have been produced over the years. This AGN concentrates on the final alternator Markon Range that was manufactured before production ceased – the BL105 and the SL105. For information on any other Marcon Ranges, please contact [email protected]. The BL105 The Markon Capacitor Brushless BL 105 family of alternators actually operate with a system based on a leading power factor, 'self-excitation' principle. Within the alternator's stator there are two isolated windings, a Main winding to power the connected load and an auxiliary winding connected to a capacitor. The sole purpose of the auxiliary winding is to "self excite" the alternator, by inducing a voltage, therefore current, into the rotor winding; which is simply connected to a diode to make the resulting current dc, therefore creating a polarised rotating magnetic field. With this excited rotor spinning within the stator, the resulting magnetic flux not AGN 102 ISSUE B/1/21 only supports and maintains the capacitor and auxiliary winding with its needs to excite the alternator, but it is also magnetising / exciting the Main winding, which is now available to power any connected electrical load.
    [Show full text]