Kyanar® Hompolymer Chemical Resistance Guide for Waste Drainage

Total Page:16

File Type:pdf, Size:1020Kb

Kyanar® Hompolymer Chemical Resistance Guide for Waste Drainage HOMOPOLYMER Chemical Resistance Guide for Waste Drainage Systems Arkema France - A French “société anonyme“, registered in the Nanterre (France) Trade and Companies Register under the number 319 632 790 Arkema France - A French “société anonyme“, registered in the Nanterre (France) Trade NA-Marcom - ADV# 2015-011- bc/pp- 9-2015 Listed in ICC ES PMG 1060 and in IAPMO UNIFORM ES 0250 as compliant to ASTM F 1673 and ASTM E 84 25/50 KYNAR® POLYVINYLIDENE FLUORIDE (PVDF) RESIN Kynar ® polyvinylidene fluoride (PVDF) These Kynar ® PVDF resins are designed In addition to its notable fire and smoke resin is a tough engineering thermoplastic especially for harsh environments such as characteristics, Kynar ® PVDF resin has these that offers a unique balance of perfor- those of restrictive return air plenums and important properties: mance properties. It has the characteristic corrosive chemical waste streams. These Mechanical strength and toughness stability of fluoropolymers when exposed environments are generally found in: High abrasion resistance to harsh thermal, chemical and ultraviolet Pharmaceutical industries High thermal stability environments. Chemical industries High dielectric strength College laboratories High purity For chemical and high temperature High school laboratories Readily melt processable resistance, low permeability and high Hospital laboratories Resistant to most chemicals and solvents mechanical strength, Kynar ® PVDF resin is Food and Beverage Facilities Resistant to ultraviolet and nuclear used as a contact surface for the produc- radiation tion, storage and transfer of corrosive Independent testing of Kynar ® PVDF resin Resistant to weathering fluids. Kynar ® PVDF resin is used in has confirmed the resin and the piping Resistant to fungi mechanical components, fabricated fabricated from the resin meet the Interna- Low permeability to most gases and vessels, tanks, pumps, valves, filters, heat tional Mechanical Code (IMC) require- liquids exchangers, tower packing, piping ments for material installed in the plenum. Low flame and smoke characteristics systems, as well as other applications. Material Flame Smoke Spread Developed The following pages list the guidelines for Rating Rating using Kynar ® PVDF products in chemical NFPA & IMC Plenum 25 50 ® Requirement waste drainage applications. Kynar PVDF resin is suitable for short-term contact with ® Kynar PVDF 740-02 5 35 many chemicals up to 150˚C (300˚F). If Kynar ® PVDF 1000HD 0 10 your application involves mixtures of chemi- cals and temperatures above 40˚C, Kynar® PVDF resin will most likely be suitable, but ® Kynar PVDF results are listed in Arkema recommends that you consult our ICC ES PMG 1060 and in technical staff prior to installing your system. Steiner Tunnel used for ASTM E-84 Testing IAPMO UNIFORM ES 0250 as compliant to ASTM F 1673 and ASTM E 84 25/50 Corrosive Waste Drainage and Plenum Applications Select grades of Kynar® PVDF resin easily achieve the flame spread/smoke developed rating of 25/50 when tested in accordance with ASTM E-84. This en- ables Kynar® PVDF resin pipe to be used in the plenum for applications such as corrosive waste drainage and laboratory chemical systems. \ Rating for Low Pressure Drainage System Chemical Substance Concentration* Rating Chemical Substance Concentration* Rating Guidelines Acetaldehyde A- Benzaldehyde A- for using Acetamide A- Benzene A+ Kynar® PVDF Acetic Acid A Benzenesulfonic Acid Aqueous solution or solid A+ products in Acetic Acid Benzoic Acid A+ 10% in water A+ chemical waste Acetic Acid 50% in water A+ Benzoyl Chloride A+ drainage. Acetic Acid 80% in water A+ Benzoyl Peroxide A+ Acetic Anhydride A- Benzyl Alcohol A+ Kynar® PVDF is suitable Acetone A- Benzyl Chloride A+ for short term contact Acetone 10% in water A Benzyl Ether A- with many chemicals up to 150oC (300oF). If Benzylamine Aqueous solution or liquid A- Acetonitrile A- your application involves Acetophenone A- Black Liquor A+ mixtures of chemicals and o Acetyl Bromide A Bleaching Agents A+ temperatures above 40 C, Kynar® PVDF resin will Acetyl Chloride A Borax A+ most likely be suitable, but Acetylacetone A- Boric Acid A+ Arkema recommends that Acetylene A+ Boron Trifluoride A+ you consult our technical staff prior to installing your Acrylonitrile A- Brine A+ system. Adipic Acid A+ Brine, acid A+ Air A+ Brine, basic A+ Alcoholic Spirits 40% Ethyl Alcohol A+ Brine, chlorinated acid A+ *pure substance unless otherwise indicated. Allyl Alcohol A+ Bromic Acid Aqueous solution A+ Allyl Chloride A+ Bromine dry gas A+ A+: Suitable for elevated Aluminum Acetate Aqueous solution or solid A+ Bromine, liquid A+ temperatures varying with chemical in question. Aluminum Bromide A+ Bromine, water A+ Aluminum Chloride Up to 40% in water A+ Bromobenzene A+ A: Suitable for continuous Aluminum Fluoride Aqueous solution or solid A+ Bromoform A+ ambient conditions and for Aluminum Hydroxide A+ m-Bromotoluene A+ short term elevated tempera- ture varying with chemical Butadiene A+ Aluminum Nitrate Aqueous solution or solid A+ in question. Aluminum Oxychloride A+ Butane A+ Aluminum Sulfate Aqueous solution or solid A+ Butanediol Aqueous solution or liquid A+ A-: Suitable for short term use at full strength under Ammonia, gas A- Butyl Acetate A- ambient conditions, and Ammonia, Liquid A Butyl Acrylate A suitable for continuous use Ammonium Acetate Aqueous solution or solid A+ Butyl Alcohol Aqueous solution or liquid A+ at ambient conditions in diluted form. Ammonium Alum Aqueous solution or solid A+ sec-Butyl Alcohol Aqueous solution or liquid A+ Ammonium Bifluoride Aqueous solution or solid A+ t-Butyl Alcohol Aqueous solution or liquid A+ B: Suitable for short-term Ammonium Bromide Aqueous solution or solid A+ Butyl Bromide A+ use if concentration will be Ammonium Carbonate Aqueous solution or solid A+ Butyl Chloride A+ less than 100% , please contact Arkema technical Butyl Ether A- Ammonium Chloride Aqueous solution or solid A+ staff for assessment of a safe Ammonium Dichromate Aqueous solution or solid A+ Butyl Mercaptan A+ concentration at maximum Ammonium Fluoride Aqueous solution or solid A+ Butyl Stearate A exposre temperature. Ammonium Hydroxide Up to “concentrated” A+ Butylamine Aqueous solution or liquid A- Ammonium Metaphosphate Aqueous solution or solid A+ sec-Butylamine Aqueous solution or liquid A- Ammonium Nitrate Aqueous solution or solid A+ t-Butylamine Aqueous solution or solid A- Ammonium Persulfate Aqueous solution or solid A 1-Butylene A+ Ammonium Phosphate Aqueous solution or solid A+ Butylphenol A+ Ammonium Sulfate Aqueous solution or solid A+ Butyraldehyde A Ammonium Sulfide Aqueous solution or solid A+ Butyric Acid A+ Ammonium Thiocyanate Aqueous solution or solid A+ Calcium Acetate Aqueous solution or solid A+ Amyl Acetate A Calcium Bisulfate Aqueous solution or solid A+ Amyl Alcohol A+ Calcium Bisulfite Aqueous solution or solid A+ Sec-Amyl Alcohol A Calcium Bromide Aqueous solution or solid A+ Amyl Chloride A+ Calcium Carbonate A+ Aniline A- Calcium Chlorate Aqueous solution or solid A+ Aniline Hydrochloride Aqueous solution or solid A- Calcium Chloride Aqueous solution or solid A+ Aqua Regia A Calcium Hydroxide A+ Arsenic acid Aqueous solution A+ Calcium Hypochlorite Aqueous solution or solid A+ Asphalt A+ Calcium Nitrate Aqueous solution or solid A+ Barium Carbonate A+ Calcium Oxide A+ Barium Chloride Aqueous solution or solid A+ Calcium Phosphate A+ Barium Hydroxide A+ Calcium Sulfate A+ Barium Nitrate Aqueous solution or solid A+ Cane Sugar Liquors A+ Barium Sulfate A+ Caprylic Acid A+ Barium Sulfide A+ Carbon Dioxide A+ Beer A+ Carbon Disulfide A Kynar® is a registered Beet Sugar Liquors A+ Carbon Monoxide A+ trademark of Arkema Inc. Rating for Low Pressure Drainage System Chemical Substance Concentration* Rating Chemical Substance Concentration* Rating Guidelines Carbon Tetrachloride A+ Dibutyl Sebacate B for using Carbonic Acid A+ Dibutylamine Aqueous solution or liquid A- Kynar® PVDF Casein A+ Dichloroacetic Acid Aqueous solution or liquid A+ products in Castor Oil A+ o-Dichlorobenzene A+ chemical waste Chloral Hydrate A Dichlorodimethylsilane A+ drainage. Chlorinated Phenol A+ Dichloroethylene A+ Chlorine 5% in CCI4 A+ 2,2-Dichloropropionic Acid A Kynar® PVDF is suitable Chlorine, gas A+ aa-Dichlorotoluene A+ for short term contact with many chemicals Chlorine, liquid A+ Diesel Fuels A+ up to 150oC (300oF). If Chlorine Dioxide A+ Diethanolamine Aqueous solution or liquid A- your application involves Chlorine Water A+ Diethylamine Aqueous solution or liquid A- mixtures of chemicals and temperatures above 40oC, Chloroacetic Acid Diethyl Malonate B Aqueous solution or pure A Kynar® PVDF resin will Chloroacetyl Chloride A Diethylenetriamine Aqueous solution or liquid A- most likely be suitable, but Chlorobenzene A+ Diglycolic Acid A Arkema recommends that you consult our technical Chlorobenzene-sulfonic Acid Aqueous solution or pure A+ Diisobutyl Ketone A- staff prior to installing your Chlorobenzyl Chloride A+ Diisobutylene A+ system. Chlorofluorocarbon 11 A+ Diisopropyl Ketone A- Chlorofluorocarbon 12 A+ Dimethyl Acetamide B *pure substance unless Chlorofluorocarbon 13 A+ Dimethyl Formamide A- otherwise indicated. Chlorofluorocarbon 14 A+ Dimethyl Phthalate A- A+: Suitable for elevated Chlorofluorocarbon 21 A+ Dimethyl Sulfate A- temperatures varying with Chlorofluorocarbon 22 A+ Dimethyl Sulfoxide A- chemical in question. Chlorofluorocarbon 113 A+ Dimethylamine Aqueous solution or gas A- A: Suitable for continuous ambi-
Recommended publications
  • Direct Preparation of Some Organolithium Compounds from Lithium and RX Compounds Katashi Oita Iowa State College
    Iowa State University Capstones, Theses and Retrospective Theses and Dissertations Dissertations 1955 Direct preparation of some organolithium compounds from lithium and RX compounds Katashi Oita Iowa State College Follow this and additional works at: https://lib.dr.iastate.edu/rtd Part of the Organic Chemistry Commons Recommended Citation Oita, Katashi, "Direct preparation of some organolithium compounds from lithium and RX compounds " (1955). Retrospective Theses and Dissertations. 14262. https://lib.dr.iastate.edu/rtd/14262 This Dissertation is brought to you for free and open access by the Iowa State University Capstones, Theses and Dissertations at Iowa State University Digital Repository. It has been accepted for inclusion in Retrospective Theses and Dissertations by an authorized administrator of Iowa State University Digital Repository. For more information, please contact [email protected]. INFORMATION TO USERS This manuscript has been reproduced from the microfilm master. UMI films the text directly from the original or copy submitted. Thus, some thesis and dissertation copies are in typewriter face, while others may be from any type of computer printer. The quality of this reproduction is dependent upon the quality of the copy submitted. Broken or indistinct print, colored or poor quality illustrations and photographs, print bleedthrough, substandard margins, and improper alignment can adversely affect reproduction. In the unlikely event that the author did not send UMI a complete manuscript and there are missing pages, these will be noted. Also, if unauthorized copyright material had to be removed, a note will indicate the deletion. Oversize materials (e.g., maps, drawings, charts) are reproduced by sectioning the original, beginning at the upper left-hand comer and continuing from left to right in equal sections with small overiaps.
    [Show full text]
  • Progresses in Synthesis and Application of Sic Films: from CVD to ALD and from MEMS to NEMS
    micromachines Review Progresses in Synthesis and Application of SiC Films: From CVD to ALD and from MEMS to NEMS Mariana Fraga 1,* and Rodrigo Pessoa 2,* 1 Instituto de Ciência e Tecnologia (ICT), Universidade Federal de São Paulo (Unifesp), São José dos Campos SP 12231-280, Brazil 2 Laboratório de Plasmas e Processos (LPP), Instituto Tecnológico de Aeronáutica (ITA), São José dos Campos SP 12228-900, Brazil * Correspondence: [email protected] (M.F.); [email protected] (R.P.) Received: 2 August 2020; Accepted: 20 August 2020; Published: 24 August 2020 Abstract: A search of the recent literature reveals that there is a continuous growth of scientific publications on the development of chemical vapor deposition (CVD) processes for silicon carbide (SiC) films and their promising applications in micro- and nanoelectromechanical systems (MEMS/NEMS) devices. In recent years, considerable effort has been devoted to deposit high-quality SiC films on large areas enabling the low-cost fabrication methods of MEMS/NEMS sensors. The relatively high temperatures involved in CVD SiC growth are a drawback and studies have been made to develop low-temperature CVD processes. In this respect, atomic layer deposition (ALD), a modified CVD process promising for nanotechnology fabrication techniques, has attracted attention due to the deposition of thin films at low temperatures and additional benefits, such as excellent uniformity, conformability, good reproducibility, large area, and batch capability. This review article focuses on the recent advances in the strategies for the CVD of SiC films, with a special emphasis on low-temperature processes, as well as ALD. In addition, we summarize the applications of CVD SiC films in MEMS/NEMS devices and prospects for advancement of the CVD SiC technology.
    [Show full text]
  • Transport of Dangerous Goods
    ST/SG/AC.10/1/Rev.16 (Vol.I) Recommendations on the TRANSPORT OF DANGEROUS GOODS Model Regulations Volume I Sixteenth revised edition UNITED NATIONS New York and Geneva, 2009 NOTE The designations employed and the presentation of the material in this publication do not imply the expression of any opinion whatsoever on the part of the Secretariat of the United Nations concerning the legal status of any country, territory, city or area, or of its authorities, or concerning the delimitation of its frontiers or boundaries. ST/SG/AC.10/1/Rev.16 (Vol.I) Copyright © United Nations, 2009 All rights reserved. No part of this publication may, for sales purposes, be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, electrostatic, magnetic tape, mechanical, photocopying or otherwise, without prior permission in writing from the United Nations. UNITED NATIONS Sales No. E.09.VIII.2 ISBN 978-92-1-139136-7 (complete set of two volumes) ISSN 1014-5753 Volumes I and II not to be sold separately FOREWORD The Recommendations on the Transport of Dangerous Goods are addressed to governments and to the international organizations concerned with safety in the transport of dangerous goods. The first version, prepared by the United Nations Economic and Social Council's Committee of Experts on the Transport of Dangerous Goods, was published in 1956 (ST/ECA/43-E/CN.2/170). In response to developments in technology and the changing needs of users, they have been regularly amended and updated at succeeding sessions of the Committee of Experts pursuant to Resolution 645 G (XXIII) of 26 April 1957 of the Economic and Social Council and subsequent resolutions.
    [Show full text]
  • Gas-Phase Chemistry of Methyl-Substituted Silanes in a Hot-Wire Chemical Vapour Deposition Process
    University of Calgary PRISM: University of Calgary's Digital Repository Graduate Studies The Vault: Electronic Theses and Dissertations 2013-08-27 Gas-phase Chemistry of Methyl-Substituted Silanes in a Hot-wire Chemical Vapour Deposition Process Toukabri, Rim Toukabri, R. (2013). Gas-phase Chemistry of Methyl-Substituted Silanes in a Hot-wire Chemical Vapour Deposition Process (Unpublished doctoral thesis). University of Calgary, Calgary, AB. doi:10.11575/PRISM/26257 http://hdl.handle.net/11023/891 doctoral thesis University of Calgary graduate students retain copyright ownership and moral rights for their thesis. You may use this material in any way that is permitted by the Copyright Act or through licensing that has been assigned to the document. For uses that are not allowable under copyright legislation or licensing, you are required to seek permission. Downloaded from PRISM: https://prism.ucalgary.ca UNIVERSITY OF CALGARY Gas-phase Chemistry of Methyl-Substituted Silanes in a Hot-wire Chemical Vapour Deposition Process by Rim Toukabri A THESIS SUBMITTED TO THE FACULTY OF GRADUATE STUDIES IN PARTIAL FULFILMENT OF THE REQUIREMENTS FOR THE DEGREE OF DOCTOR OF PHILOSOPHY DEPARTMENT OF CHEMISTRY CALGARY, ALBERTA August, 2013 © Rim Toukabri 2013 Abstract The primary decomposition and secondary gas-phase reactions of methyl- substituted silane molecules, including monomethylsilane (MMS), dimethylsilane (DMS), trimethylsilane (TriMS) and tetramethylsilane (TMS), in hot-wire chemical vapour deposition (HWCVD) processes have been studied using laser ionization methods in combination with time of flight mass spectrometry (TOF-MS). For all four molecules, methyl radical formation and hydrogen molecule formation have been found to be the common decomposition steps on both tungsten (W) and tantalum (Ta) filaments.
    [Show full text]
  • A Study of the Decomposition of Some Aromatic Diazonium Hexafluorophosphate Salts
    University of Windsor Scholarship at UWindsor Electronic Theses and Dissertations Theses, Dissertations, and Major Papers 1-1-1964 A study of the decomposition of some aromatic diazonium hexafluorophosphate salts. William A. Redmond University of Windsor Follow this and additional works at: https://scholar.uwindsor.ca/etd Recommended Citation Redmond, William A., "A study of the decomposition of some aromatic diazonium hexafluorophosphate salts." (1964). Electronic Theses and Dissertations. 6038. https://scholar.uwindsor.ca/etd/6038 This online database contains the full-text of PhD dissertations and Masters’ theses of University of Windsor students from 1954 forward. These documents are made available for personal study and research purposes only, in accordance with the Canadian Copyright Act and the Creative Commons license—CC BY-NC-ND (Attribution, Non-Commercial, No Derivative Works). Under this license, works must always be attributed to the copyright holder (original author), cannot be used for any commercial purposes, and may not be altered. Any other use would require the permission of the copyright holder. Students may inquire about withdrawing their dissertation and/or thesis from this database. For additional inquiries, please contact the repository administrator via email ([email protected]) or by telephone at 519-253-3000ext. 3208. A STUDY OF THE DECOMPOSITION OF SOME AROMATIC DIAZONIUM HEXAFLUOROPHOSPHATE SALTS BY WILLIAM A. REDMOND A Thesis Submitted to the Faculty of Graduate Studies through' the Department of Chemistry in Partial Fulfillment of the Requirements for the Degree of Doctor of Philosophy at the University of Windsor Windsor, Ontario 1964 Reproduced with permission of the copyright owner. Further reproduction prohibited without permission.
    [Show full text]
  • Syntheses and Eliminations of Cyclopentyl Derivatives David John Rausch Iowa State University
    Iowa State University Capstones, Theses and Retrospective Theses and Dissertations Dissertations 1966 Syntheses and eliminations of cyclopentyl derivatives David John Rausch Iowa State University Follow this and additional works at: https://lib.dr.iastate.edu/rtd Part of the Organic Chemistry Commons Recommended Citation Rausch, David John, "Syntheses and eliminations of cyclopentyl derivatives " (1966). Retrospective Theses and Dissertations. 2875. https://lib.dr.iastate.edu/rtd/2875 This Dissertation is brought to you for free and open access by the Iowa State University Capstones, Theses and Dissertations at Iowa State University Digital Repository. It has been accepted for inclusion in Retrospective Theses and Dissertations by an authorized administrator of Iowa State University Digital Repository. For more information, please contact [email protected]. This dissertation has been microfilmed exactly as received 66—6996 RAUSCH, David John, 1940- SYNTHESES AND ELIMINATIONS OF CYCLOPENTYL DERIVATIVES. Iowa State University of Science and Technology Ph.D., 1966 Chemistry, organic University Microfilms, Inc., Ann Arbor, Michigan SYNTHESES AND ELIMINATIONS OF CYCLOPENTYL DERIVATIVES by David John Rausch A Dissertation Submitted to the Graduate Faculty in Partial Fulfillment of The Requirements for the Degree of DOCTOR OF PHILOSOPHY Major Subject: Organic Chemistry Approved : Signature was redacted for privacy. Signature was redacted for privacy. Head of Major Department Signature was redacted for privacy. Iowa State University Of Science and Technology Ames, Iowa 1966 ii TABLE OF CONTENTS VITA INTRODUCTION HISTORICAL Conformation of Cyclopentanes Elimination Reactions RESULTS AND DISCUSSION Synthetic Elimination Reactions EXPERIMENTAL Preparation and Purification of Materials Procedures and Data for Beta Elimination Reactions SUMMARY LITERATURE CITED ACKNOWLEDGEMENTS iii VITA The author was born in Aurora, Illinois, on October 24, 1940, to Mr.
    [Show full text]
  • Chemical Resistance: Deco-Trowel
    CHEMICAL RESISTANCE DECO-TROWEL ® SERIES 223 Tnemec Company, Inc. 6800 Corporate Drive Kansas City, Missouri 64120-1372 +1 816-483-3400 www.tnemec.com © December 16, 2019 by Tnemec Company, Inc. Chem223 Page 1 of 19 CHEMICAL RESISTANCE DECO-TROWEL ® | SERIES 223 COMMON PROBLEM AREAS FOR COATINGS AND SOLUTIONS Problem: Coating Solution: Points of failure Carefully and due to thin spots fully coat in coating Problem: Rough Pinhole Solution: Uneven Undercut Grind smooth welds Problem: Gaps between Solution: plates, coating Continuous can not cover welds Problem: Gaps between Solution: plates, coating Continuous can not cover welds Problem: Coating Sharp surface Solution: contours create Round the thin spots in contours coating Problem: Skip welding Solution: creates gaps Continuous that coating welds can not cover Problem: Skip welding Solution: creates gaps Continuous that coating welds can not cover 2 channels back to back IMPORTANT: Definitions for the terms and acronyms used in this guide to describe the recommended exposures, along with other important information, can be found on the cover page of this guide or by contacting Tnemec Technical Service. Coatings should not be applied in a chemical exposure environment until the user has thoroughly read and understood the product information and full project details have been discussed with Tnemec Technical Service. Tnemec Company, Inc. 6800 Corporate Drive Kansas City, Missouri 64120-1372 +1 816-483-3400 www.tnemec.com © December 16, 2019 by Tnemec Company, Inc. Chem223 Page 2 of 19 CHEMICAL RESISTANCE DECO-TROWEL ® | SERIES 223 ¹ Product is NOT suitable for direct or indirect food contact. Intended Use and temperature information relates to product’s performance capabilities only.
    [Show full text]
  • Kinetic Modeling of the Thermal Destruction of Nitrogen Mustard
    Kinetic Modeling of the Thermal Destruction of Nitrogen Mustard Gas Juan-Carlos Lizardo-Huerta, Baptiste Sirjean, Laurent Verdier, René Fournet, Pierre-Alexandre Glaude To cite this version: Juan-Carlos Lizardo-Huerta, Baptiste Sirjean, Laurent Verdier, René Fournet, Pierre-Alexandre Glaude. Kinetic Modeling of the Thermal Destruction of Nitrogen Mustard Gas. Journal of Physical Chemistry A, American Chemical Society, 2017, 121 (17), pp.3254-3262. 10.1021/acs.jpca.7b01238. hal-01708219 HAL Id: hal-01708219 https://hal.archives-ouvertes.fr/hal-01708219 Submitted on 13 Feb 2018 HAL is a multi-disciplinary open access L’archive ouverte pluridisciplinaire HAL, est archive for the deposit and dissemination of sci- destinée au dépôt et à la diffusion de documents entific research documents, whether they are pub- scientifiques de niveau recherche, publiés ou non, lished or not. The documents may come from émanant des établissements d’enseignement et de teaching and research institutions in France or recherche français ou étrangers, des laboratoires abroad, or from public or private research centers. publics ou privés. Kinetic Modeling of the Thermal Destruction of Nitrogen Mustard Gas Juan-Carlos Lizardo-Huerta†, Baptiste Sirjean†, Laurent Verdier‡, René Fournet†, Pierre-Alexandre Glaude†,* †Laboratoire Réactions et Génie des Procédés, CNRS, Université de Lorraine, 1 rue Grandville BP 20451 54001 Nancy Cedex, France ‡DGA Maîtrise NRBC, Site du Bouchet, 5 rue Lavoisier, BP n°3, 91710 Vert le Petit, France *corresponding author: [email protected] Abstract The destruction of stockpiles or unexploded ammunitions of nitrogen mustard (tris (2- chloroethyl) amine, HN-3) requires the development of safe processes.
    [Show full text]
  • Nerve Agent - Lntellipedia Page 1 Of9 Doc ID : 6637155 (U) Nerve Agent
    This document is made available through the declassification efforts and research of John Greenewald, Jr., creator of: The Black Vault The Black Vault is the largest online Freedom of Information Act (FOIA) document clearinghouse in the world. The research efforts here are responsible for the declassification of MILLIONS of pages released by the U.S. Government & Military. Discover the Truth at: http://www.theblackvault.com Nerve Agent - lntellipedia Page 1 of9 Doc ID : 6637155 (U) Nerve Agent UNCLASSIFIED From lntellipedia Nerve Agents (also known as nerve gases, though these chemicals are liquid at room temperature) are a class of phosphorus-containing organic chemicals (organophosphates) that disrupt the mechanism by which nerves transfer messages to organs. The disruption is caused by blocking acetylcholinesterase, an enzyme that normally relaxes the activity of acetylcholine, a neurotransmitter. ...--------- --- -·---- - --- -·-- --- --- Contents • 1 Overview • 2 Biological Effects • 2.1 Mechanism of Action • 2.2 Antidotes • 3 Classes • 3.1 G-Series • 3.2 V-Series • 3.3 Novichok Agents • 3.4 Insecticides • 4 History • 4.1 The Discovery ofNerve Agents • 4.2 The Nazi Mass Production ofTabun • 4.3 Nerve Agents in Nazi Germany • 4.4 The Secret Gets Out • 4.5 Since World War II • 4.6 Ocean Disposal of Chemical Weapons • 5 Popular Culture • 6 References and External Links --------------- ----·-- - Overview As chemical weapons, they are classified as weapons of mass destruction by the United Nations according to UN Resolution 687, and their production and stockpiling was outlawed by the Chemical Weapons Convention of 1993; the Chemical Weapons Convention officially took effect on April 291997. Poisoning by a nerve agent leads to contraction of pupils, profuse salivation, convulsions, involuntary urination and defecation, and eventual death by asphyxiation as control is lost over respiratory muscles.
    [Show full text]
  • Fumigation for Rabbit Control
    Fumigation for rabbit control Introduction: Fumigation is a valuable tool in successful rabbit management programs. It is an effective follow-up technique to poison baiting and warren ripping, and is a particularly useful control method in areas where other techniques cannot be used (eg poison baiting). Fumigation works by replacing the air in warrens with Figure 1: Phostoxin tablets and dry paper are pushed deep lethal gasses, which are in-turn inhaled by rabbits, into the warren entrance. Image: Invasive Animals CRC causing them to suffocate and die. There are two types of fumigation: Fumigants Chloropicrin: Chloropicrin is a colourless, toxic liquid • pressure fumigation - where the fumigant is generated that is currently used in Australia as an insecticide, soil outside the warren and forced into the warren under and warren fumigant, and rodenticide. Chloropicrin pressure, usually from a pump is classified as a dangerous poison (Schedule 7) as • diffusion (or static) fumigation – where tablets are placed it has a high potential to cause harm, even at low in active burrows (Figure 1) and the fumigant generated exposures. Chloropicrin has recently been placed under is allowed to passively diffuse through the warren (this is review by the Australian Pesticides and Veterinary the preferred method)1. Medicines Authority (APVMA) because of environmental, There are strict regulations around the use of fumigants human health and human safety concerns. It is not for rabbit control that reduce the risk of harm to recommended for use, even though it is still registered operators. For this reason, users may also require training in some states. Pressure fumigation using chloropicrin ® or accreditation before using approved fumigants.
    [Show full text]
  • Microflex Gloves Chemical Compatibility Chart
    1 1 1 2 2 3 1 CAUTION (LATEX): This product contains natural rubber 2 CAUTION (NITRILE: MEDICAL GRADE): Components used 3 CAUTION (NITRILE: NON-MEDICAL GRADE)): These latex (latex) which may cause allergic reactions. Safe use in making these gloves may cause allergic reactions in gloves are for non-medical use only. They may NOT be of this glove by or on latex sensitized individuals has not some users. Follow your institution’s policies for use. worn for barrier protection in medical or healthcare been established. applications. Please select other gloves for these applications. Components used in making these gloves may cause allergic reactions in some users. Follow your institution’s policies for use. For single use only. NeoPro® Chemicals NeoPro®EC Ethanol ■NBT Ethanolamine (99%) ■NBT Ether ■2 Ethidium bromide (1%) ■NBT Ethyl acetate ■1 Formaldehyde (37%) ■NBT Formamide ■NBT Gluteraldehyde (50%) ■NBT Test Method Description: The test method uses analytical Guanidine hydrochloride ■NBT equipment to determine the concentration of and the time at which (50% ■0 the challenge chemical permeates through the glove film. The Hydrochloric acid ) liquid challenge chemical is collected in a liquid miscible chemical Isopropanol ■NBT (collection media). Data is collected in three separate cells; each cell Methanol ■NBT is compared to a blank cell which uses the same collection media as both the challenge and Methyl ethyl ketone ■0 collection chemical. Methyl methacrylate (33%) ■0 Cautionary Information: These glove recommendations are offered as a guide and for reference Nitric acid (50%) ■NBT purposes only. The barrier properties of each glove type may be affected by differences in material Periodic acid (50%) ■NBT thickness, chemical concentration, temperature, and length of exposure to chemicals.
    [Show full text]
  • Studies on Isotope Separation of Lithium by Electromigration in Fused Lithium Bromide and Potassium Bromide Mixture, (II) Composition of Salt in Anode Compartment
    Journal of NUCLEARSCIENCE and TECHNOLOGY,7 (10), p. 522~526 (October 1970). Studies on Isotope Separation of Lithium by Electromigration in Fused Lithium Bromide and Potassium Bromide Mixture, (II) Composition of Salt in Anode Compartment Yoshinobu YAMAMURA* and Shin SUZUKI* Received May 13, 1970 Accurate knowledge on the salt composition in the anode compartment is indispensable when 6Li is to be highly enriched by electromigration in fused LiBr-KBr mixture. A study was made on the dependence on temperature shown by the salt composition in the anode com- partment. It was observed that sustained electromigration led to a salt composition in the anode compartment that was determined by the prevailing temperature. The composition was observed for various temperatures between 380- and 740-C: In terms of the ratio Li/K in chemical equivalent, the values were 1.31 at 380-C, 1.29 at 420-C, 1.31 at 460-C, 1.41 at 500-C, 1.76 at 540-C, 1.82 at 580-C, 1.95 at 620-C, 2.16 at 680-C and 2.34 at 740-C. These results can be explained by assuming that the fused LiBr-KBr mixture is a system composed of two simple salts and their eutectic, and that at temperatures below 550-C, which is the melting point of LiBr, LiBr and KBr are dissolved in fused eutectic, while KBr is dissolved in the fused eutectic and LiBr at temperatures between 550- and 738-C, which latter is the melting point of KBr. I. INTRODUCTION . EXPERIMENTAL In a previous study(1), one of authors suc- 1.
    [Show full text]