Which One Do I Choose? Pick the Lab Equipment That Would Be Best to Use for the Following Questions

Total Page：16

File Type：pdf, Size：1020Kb

Name _____Savage – ANSWER KEY___________________________Class: _______ Date: ____________________ Which One Do I Choose? Pick the lab equipment that would be best to use for the following questions. 1. What do I use to most accurately measure 31.2 mL of acetic acid? Buret 2. Where do I place a hot test tube while it cools? Test tube rack 3. How can I tell how hot the water is? Thermometer 4. What do I wear to protect my eyes? Goggles 5. How can I heat a beaker (without using any gas)? Hot plate 6. What can I use to cover a beaker while I am gently heating it? Watch Glass 7. What can I use to transfer a small amount of a solid chemical to another container? Forceps/Scoopula 8. What can I use to protect my clothing during lab? Lab apron 9. What can I use to pick up a hot test tube? Test tube tongs 10. What can I use to measure 21 mL of water? Graduated cylinder 11. What can I use to scrub and clean the test tube? Test tube brush 12. How can I measure 25.2 g of a solid chemical (without using electricity)? Triple beam balance 13. What can I place a solid chemical in so that I can heat it over very high heat? Crucible 14. What can I use to find the length of a desk? Meter stick 15. What can I use to transfer small amounts of liquids from one container to another? Pipet 16. What can I use to pick up a hot crucible? Crucible tongs 17. What can I attach the iron ring (ring clamp) on? Ring stand 18. What do I place under a crucible (on top of the iron ring) while heating? Clay triangle 19. What do I place under a beaker (on top of the iron ring) while heating? Wire gauze 20. What can I use to grind up a solid chemical into a powder? Mortar & pestle .

Copy Link

Recommended publications

VACUUM RECOVERY of ASPHALT EMULSION RESIDUE (An Arizona Method)
ARIZ 504 July 1980 (3 Pages) VACUUM RECOVERY OF ASPHALT EMULSION RESIDUE (An Arizona Method) Scope (d) No. 10 sieve conforming to AASHTO designation M 92. I. This method describes a low temperature vacuum procedure for recovery of the asphalt residue (e) Vacuum recovery apparatus as shown from asphalt emulsions. It is is not suitable for assembled in Fig. I. quantitative recovery of solvents from emulsions I) Vacuum source capable of producing an containing low boiling range distillates. absolute vacuum within the system of approximately 710 mm (28 in.) mercury. Apparatus 2) Thermometer - shall have a range of _5° to 1. The apparatus shall consist of the following: +200°C (23°F to 392°F). The overall length (a) Brass stirring rod. shall be 600 mm (24 in.) and the distance from the bottom of the bulb to the zero point (b) 8 oz. ointment can. shall be 300 mm (12 in.) (c) 100 ml. stainless steel beaker. 3) Stirrer hot plate. VACUUM RECOVERY APPARATUS 300 mm Allihn condenser H20 Out / Thermometer Vacuum Release Pinch Clamp 500 m. 1,000 ml. Filtration Flask Filtration Flask Teflon Stirring Bar H20 In 500 ml. Filtration Flask Portable Heat Gun FIGURE I ARIZ 504 July 1980 4) Teflon covered stirring bar. (g) Insert the stoppered themometer (positioned 5) 1000 ml. and two 500 ml. filtering flasks with in the stopper at an angle to prevent contact with tubulation. stirring bar) into the flask and set on hot plate at a medium high heat setting (#4). The bulb of the 6) 300 mm Allihn condensor.
[Show full text]
METHODS & STANDARD OPERATING PROCEDURES (Sops)
METHODS & STANDARD OPERATING PROCEDURES (SOPs) OF EMISSION TESTING IN HAZARDOUS WASTE INCINERATOR FOREWARD COVR PAGE TEAM CHAPTER TITLE PAGE NO Chapter - 1 Stack Monitoring – Material And Methodology For Isokinetic Sampling 1-28 Chapter - 2 Standard Operating Procedure (SOP) For Particulate Matter Determination 29-38 Chapter - 3 Determination Of Hydrogen Halides (Hx) And Halogens From Source Emission 39-54 Chapter - 4 Standard Operating Procedure For The Sampling Of Hydrogen Halides And Halogens From Source Emission 55-61 Determination Of Metals And Non Metals Emissions From Chapter - 5 Stationarysources 62-79 Standard Operating Procedure (Sop) For Sampling Of Metals And Non Chapter - 6 Metals & 80-97 Standard Operating Procedure (Sop) Of Sample Preparation For Analysis Of Metals And Non Metals Chapter - 7 Determination Of Polychlorinated Dibenzo-P-Dioxins And 98-127 Polychlorinated Dibenzofurans Standard Operating Procedure For Sampling Of Polychlorinated Chapter - 8 Dibenzo-P-Dioxins And Polychlorinated Dibenzofurans & 128-156 Standard Operating Procedure For Analysis Of Polychlorinated Dibenzo- P-Dioxins And Polychlorinated Dibenzofurans Project Team 1. Dr. B. Sengupta, Member Secretary - Overall supervision 2. Dr. S.D. Makhijani, Director - Report Editing 3. Sh. N.K. Verma, Ex Additional Director - Project co-ordination 4. Sh. P.M. Ansari, Additional Director - Report Finalisation 5. Dr. D.D. Basu, Senior Scientist - Guidance and supervision 6. Sh. Paritosh Kumar, Sr. Env. Engineer - Report processing 7. Sh. Dinabandhu Gouda, Env. Engineer - Data compilation, analysis and preparation of final report 8. Sh. G. Thirumurthy, AEE - - do - 9. Sh. Abhijit Pathak, SSA - - do - 10. Ms. Trapti Dubey, Jr. Professional (Scientist) - - do - 11. Er. Purushotham, Jr. Professional (Engineer) - - do - 12.
[Show full text]
Catching up with Runaway Hot Plates
Catching up with Runaway Hot Plates Kimberly Brown1, Mark Mathews2, Joseph Pickel3 1‐ Office of Environmental Health and Radiation Safety University of Pennsylvania, Philadelphia, PA 2‐ Environmental Safety and Health Directorate, Oak Ridge National Laboratory, Oak Ridge TN 3‐ Physical Sciences Directorate, Oak Ridge National Laboratory, Oak Ridge TN Recent Events with Malfunctioning Abstract Cause of Fire identified as Runaway Hot Plates Hotplate Several research institutions report safety events involving hotplates that have been In recent years, there have been numerous reports of runaway hot plates — hot left on and unattended or that have heated uncontrollably, sometimes resulting in plates that heat uncontrolled despite the setting or the fact that the controls are in significant damage in the process. Some of the known events are listed below: the off position. Some of these events have resulted in damage to research • June 29, 2005: Lawrence Berkeley National Laboratory — A laboratory hot plate’s facilities. The Division of Chemical Health and Safety has investigated this issue power switch failed, resulting in a fire in the fume hood. Although the switch using all available information and soliciting additional information viaasurvey position, switch detent, and indicator light demonstrated that the power was off, conducted in April 2017 to determine the cause of these issues and to develop Valid NRTL listing electrical power continued to flow to the heating elements. strategies to prevent future “runaways‘’. Results of this survey and best practices (http://www2.lbl.gov/ehs/Lessons/pdf/FinalHotPlateLL.pdf) are described herein. • April 2007: University of California — Following a March 2007 report of a malfunctioning hot plate that heats while in the ‘off’ position, UC EHS personnel send out a system wide message concerning the issue citing “several explosions or Survey Information fire events involving defective hot plates that resulted in injuries to laboratory employees or damage to laboratories” over the previous five years.
[Show full text]
Science Safety
2010 Mississippi Science Framework Science Safety The guides that are cited below were developed by the Council of State Science Supervisors (CSSS) with support from the Eisenhower National Clearinghouse for Mathematics and Science Education, the National Aeronautics and Space Administration, Dupont Corporation, Intel Corporation, Americal Chemical Society, and the National Institutes of Health. Science Safety Booklets may be printed for use by educators. • Science Safety Booklets • Science and Safety: It's Elementary (PDF) - A Elementary Safety Guide • Science and Safety, Making the Connection (PDF) - A Secondary Safety Guide . Approved July 25, 2008 1 2010 Mississippi Science Framework A SUGGESTED PATTERN FOR CHEMICAL STORAGE The alphabetical method for storing chemicals presents hazards because chemicals, which can react violently with each other, may be stored in close proximity. Schools may wish to devise a simple color-coding scheme to address this problem. The code shown below, reproduced with permission from School Science Laboratories-A Guide to Some Hazardous Substances by the Council of State Science Supervisors, includes both solid and striped colors which are used to designate specific hazards as follows: Red - Flammability hazard: Store in a flammable chemical storage area. Red Stripe - Flammability hazard: Do not store in the same area as other flammable substances. Yellow - Reactivity hazard: Store separately from other chemicals. Yellow Stripe - Reactivity hazard: Do not store with other yellow coded chemicals; store separately. White - Contact hazard: Store separately in a corrosion-proof container. White Stripe - Contact hazard: Not compatible with chemicals in solid white category. Blue - Health hazard: Store in a secure poison area. Orange - Not suitably characterized by any of the foregoing categories.
[Show full text]
Information to Users
INFORMATION TO USERS While the most advanced technology has been used to photograph and reproduce this manuscript, the quality of the reproduction is heavily dependent upon the quality of the material submitted. For example: # Manuscript pages may have indistinct print. In such cases, the best available copy has been filmed. ® Manuscripts may not always be complete. In such cases, a note will indicate that it is not possible to obtain missing pages. ® Copyrighted material may have been removed from the manuscript. In such cases, a note will indicate the deletion. Oversize materials (e.g., maps, drawings, and charts) are photographed by sectioning the original, beginning at the upper left-hand corner and continuing from left to right in equal sections with small overlaps. Each oversize page is also filmed as one exposure and is available, for an additional charge, as a standard 35mm slide or as a 17”x 23" black and white photographic print. Most photographs reproduce acceptably on positive microfilm or microfiche but lack the clarity on xerographic copies made from the microfilm. For an additional charge, 35mm slides of 6”x 9” black and white photographic prints are available for any photographs or illustrations that cannot be reproduced satisfactorily by xerography. Order Number 8717718 On-line, adaptive, optimal control of a high-density, fed-batch fermentation of streptomyces C5 Schlasner, Steven Mark, Ph.D. The Ohio State University, 1987 UMI 300N.ZeebRd. Ann Arbor, MI 48106 PLEASE NOTE: In all cases this material has been filmed in the best possible way from the available copy. Problems encountered with this document have been identified here with a check mark V 1.
[Show full text]
Vworks Automation Control User Guide
VWorks Automation Control User Guide Original Instruction Agilent Technologies Notices © Agilent Technologies, Inc. 2010 Warranty (June1987) or DFAR 252.227-7015 (b)(2) (November 1995), as applicable in any No part of this manual may be reproduced The material contained in this docu- technical data. in any form or by any means (including ment is provided “as is,” and is sub- electronic storage and retrieval or transla- ject to being changed, without notice, Safety Noticies tion into a foreign language) without prior agreement and written consent from Agi- in future editions. Further, to the max- A WARNING notice denotes a lent Technologies, Inc. as governed by imum extent permitted by applicable hazard. It calls attention to an United States and international copyright law, Agilent disclaims all warranties, operating procedure, practice, or the laws. either express or implied, with regard like that, if not correctly performed or to this manual and any information User Guide Part Number adhered to, could result in personal contained herein, including but not injury or death. Do not proceed G5415-90063 limited to the implied warranties of beyond a WARNING notice until the merchantability and fitness for a par- indicated conditions are fully Edition ticular purpose. Agilent shall not be understood and met. liable for errors or for incidental or Revision 01, April 2010 consequential damages in connection A CAUTION notice denotes a hazard. It Technical Support with the furnishing, use, or perfor- calls attention to an operating procedure, mance of this document or of any practice, or the like that, if not correctly performed or adhered to, could result in Agilent Technologies Inc.
[Show full text]
Hot Plate Safety
LABORATORY SAFETY GUIDELINE Hot Plate Safety Hot plates used in labs present many potential dangers, such as burns, fires, and electrical shock, which can cause injuries, significant disruption of lab operations, and loss of scientific data. Burns • The hot plate is a source of heat when on, and for some time after it has been turned off. The temperature of the heated plate can reach 500°C and can cause severe burns. Electric Shock • Touching the hot plate with the power cords can melt through the insultation and cause electric shock. Fire Hazard • Electrical spark hazard from either the on-off switch or the bimetallic thermostat used to regulate temperature, or both, are a design flaw issue in older hotplate models. If the equipment sparks near combustible or flammable materials, fire could result. • Exercise caution when heating flammable materials. • Hot/stirrer plates have an additional risk if an operator accidentally turns on the wrong feature. • Hot plates are NOT explosion proof or intrinsically safe. Basic Precautions: • Only use hot plates that have been approved by a Nationally Recognized Testing Laboratory (NRTL) such as Underwriter’s Laboratory (UL). • Read the manufacturer’s instructions before using and consider registering the device with the manufacturer so you will be notified of any warnings or recalls. • Periodically inspect equipment prior to use: o Do not use if the plug or cord is worn, frayed, or damaged, if the grounding pin has been removed, or if a spark is observed. o Check for corrosion of the thermostat, which can cause a spark. o Test the function of the “off” switch on each hot plate to verify that it works and the device cools quickly when the switch is in the “off” position.
[Show full text]
Construction of a Capillary Viscometer and the Study of Non-Newtonian Liquids" (1965)
Scholars' Mine Masters Theses Student Theses and Dissertations 1965 Construction of a capillary viscometer and the study of non- Newtonian liquids Hsun Kuang Yang Follow this and additional works at: https://scholarsmine.mst.edu/masters_theses Part of the Chemical Engineering Commons Department: Recommended Citation Yang, Hsun Kuang, "Construction of a capillary viscometer and the study of non-Newtonian liquids" (1965). Masters Theses. 7238. https://scholarsmine.mst.edu/masters_theses/7238 This thesis is brought to you by Scholars' Mine, a service of the Missouri S&T Library and Learning Resources. This work is protected by U. S. Copyright Law. Unauthorized use including reproduction for redistribution requires the permission of the copyright holder. For more information, please contact [email protected]. ... ··f • CONSTRUCTION OF A CAPILLARY VISCOMETER -'"' '. ·~ i : AND THE STUDY OF NON-NEWTONIAN LIQUIDS BY HSUN KUANG YANG I fl ;/() 1\?: f A THESIS submitted to the faculty of the UNIVERSITY OF MISSOURI AT ROLLA in partial fulfillment of the requirements for the Degree of MASTER OF SCIENCE IN CHEMICAL ENGINEERING Rolla, Missouri 1965 Approved by (advisor) ii ABSTRACT A capillary tube viscometer was built for the purpose of investigating the fluid properties of non-Newtonian aqueous CMC and Carbopol solutions. The viscometer was tested with Newtonian liquids (glycerine, water and two different oils) having known viscosities to insure that the viscometer was operating correctly. The shear stress-shear rate data obtained for different concen trations of CMC and Carbopol solutions were correlated using the simple power law model. The power law constants were only slightly affected by saturating the solution with iodine and carbon tetrachloride.
[Show full text]
Process Skills Review Warm-Up C
Process Skills Review Warm-Up C. • Define function • Match the following 1. Puts out fire 2. Curved line of liquid in a graduated cylinder 3. Used to observe insects A. B. Which of the following describes the correct way to handle chemicals in a laboratory? A. It is safe to combine unknown chemicals as long as only small amounts are used. B. Return all chemicals to their original containers. C. Always pour extra amounts of the chemicals called for the experiment. D. To test for odors, always use a wafting motion. Which of the following describes the correct way to handle chemicals in a laboratory? A. It is safe to combine unknown chemicals as long as only small amounts are used. B. Return all chemicals to their original containers. C. Always pour extra amounts of the chemicals called for the experiment. D. To test for odors, always use a wafting motion. What task is being performed in the picture? A. measuring mass with a graduated cylinder B. measuring length with a triple beam balance C. measuring mass with a triple beam balance D. measuring length with a metric ruler What task is being performed in the picture? A. measuring mass with a graduated cylinder B. measuring length with a triple beam balance C. measuring mass with a triple beam balance D. measuring length with a metric ruler John and Lisa are conducting an experiment in their 7th grade science class in which they are handling potentially dangerous chemicals. As John is pouring a chemical from a beaker to a graduated cylinder, he splashes some of the chemical into his eyes.
[Show full text]
Corning's Care and Safe Handling of Glassware Application Note
Care and Safe Handling of Laboratory Glassware Care and Safe Handling of Laboratory Glassware CONTENTS Glass: The Invisible Container . 1 Glass Technical Data . 2 PYREX ® Glassware . 2 PYREXPLUS ® Glassware . 2 PYREX Low Actinic Glassware . 2 VYCOR ® Glassware . 2 Suggestions for Safe Use of PYREX Glassware . 3 Safely Using Chemicals . 3 Safely Handling Glassware . 3 Heating and Cooling . 4 Autoclaving . 4 Mixing and Stirring . 5 Using Stopcocks . 5 Joining and Separating Glass Apparatus . 5 Using Rubber Stoppers . 6 Vacuum Applications . 6 Suggestions for Safe Use of PYREXPLUS Glassware . 6 Exposure to Heat . 7 Exposure to Cold . 7 Exposure to Chemicals . 7 Exposure to Ultraviolet . 7 Exposure to Microwave . 7 Exposure to Vacuum . 7 Autoclaving . 7 Labeling and Marking . 8 Suggestions for Safe Use of Fritted Glassware . 8 Selecting Fritted Glassware . 8 Proper Care of Fritted Ware . 8 Suggestions for Safe Use of Volumetric Glassware . 9 Types of Volumetric Glassware . 9 Calibrated Glassware Markings . 9 Reading Volumetric Glassware . 9 Suggestions for Cleaning and Storing Glassware . 10 Safety Considerations . 10 Cleaning PYREX Glassware . 10 Cleaning PYREXPLUS Glassware . 12 Cleaning Cell Culture Glassware . 12 Rinsing, Drying and Storing Glassware . 13 Glass Terminology . 13 Care and Safe Handling of Laboratory Glassware GLASS: THE INVISIBLE MATERIAL Q PYREX glassware comes in a wide variety of laboratory shapes, sizes and degrees of accuracy — a design to meet From the 16th century to today, chemical researchers have used every experimental need. glass containers for a very basic reason: the glass container is transparent, almost invisible and so its contents and reactions While we feel PYREX laboratory glassware is the best all- within it are clearly visible.
[Show full text]
Drying Characteristics of Buna-S Rubber; Vacuum Shelf Drying, Rotary
Iowa State University Capstones, Theses and Retrospective Theses and Dissertations Dissertations 1949 Drying characteristics of Buna-S rubber; Vacuum shelf drying, rotary vacuum drying, cabinet air drying, and through-circulation air drying Wilson Ross Barnes Iowa State College Follow this and additional works at: https://lib.dr.iastate.edu/rtd Part of the Chemical Engineering Commons Recommended Citation Barnes, Wilson Ross, "Drying characteristics of Buna-S rubber; Vacuum shelf drying, rotary vacuum drying, cabinet air drying, and through-circulation air drying " (1949). Retrospective Theses and Dissertations. 13520. https://lib.dr.iastate.edu/rtd/13520 This Dissertation is brought to you for free and open access by the Iowa State University Capstones, Theses and Dissertations at Iowa State University Digital Repository. It has been accepted for inclusion in Retrospective Theses and Dissertations by an authorized administrator of Iowa State University Digital Repository. For more information, please contact [email protected]. INFORMATION TO USERS This manuscript has been reproduced from the microfilm master. UMI films the text directly from the original or copy submitted. Thus, some thesis and dissertation copies are in typewriter face, while others may be from any type of computer printer. The quality of this reproduction is dependent upon the quality of the copy submitted. Brol<en or indistinct print, colored or poor quality illustrations and photographs, print bleedthrough, substandard margins, and improper alignment can adversely affect reproduction. In the unlikely event that the author did not send UMI a complete manuscript and there are missing pages, these will be noted. Also, if unauthorized copyright material had to be removed, a note will indicate the deletion.
[Show full text]
Laboratory Equipment AP
\ \\ , f ?7-\ Watch glass 1 Crucible and cover Evaporating dish Pneumatlo trough Beaker Safety goggles Florence Wide-mouth0 Plastic wash Dropper Funnel flask collecting bottle pipet Edenmeyer Rubber stoppers bottle flask € ....... ">. ÿ ,, Glass rod with niohrome wire Scoopula (for flame re,sting) CruoiNe tongs Rubber ubing '1 ,v .... Test-tube brush square Wire gau ÿ "\ file Burner " Tripod Florence flask: glass; common sizes are 125 mL, 250 mL, 500 .d Beaker: glass or plastic; common sizes are 50 mL, mL; maybe heated; used in making and for storing solutions. 100 mL, 250 mL, 400 mL; glass beakers maybe heated. oÿ Buret: glass; common sizes are 25 mL and 50 mL; used to Forceps: metal; used to hold or pick up small objects. Funnel: glass or plastic; common size holds 12.5-cm diameter measure volumes of solutions in titrafions. Ceramic square: used under hot apparatus or glassware. filter paper. Gas burner: constructed of metal; connected to a gas supply Clamps" the following types of clamps may be fastened to with rubber tubing; used to heat chemicals (dry or in solution) support apparatus: buret/test-tube clamp, clamp holder, double buret clamp, ring clamp, 3-pronged jaw clamp. in beakers, test tubes, and crucibles. Gas collecting tube: glass; marked in mL intervals; used to 3: Clay triangle: wire frame with porcelain supports; used to o} support a crucible. measure gas volumes. Glass rod with nichrome wire: used in flame tests. Condenser: glass; used in distillation procedures. Q. Crucible and cover: porcelain; used to heat small amounts of Graduated cylinder: glass or plastic; common sizes are 10 mL, 50 mL, 100 mL; used to measure approximate volumes; must solid substances at high temperatures.
[Show full text]