DOCSLIB.ORG

Mini Quartz Clock Movements

Total Page：16

File Type：pdf, Size：1020Kb

Download full-text PDF Read full-text
Mini Quartz Clock Movements Mini Quartz Clock Movements • 10 Year Warranty • Step Second Hand • Dimensions: 2-1/8"W x 2-1/8"H x 5/8"D • Runs on 1 "AA" Size Battery • American "I" Shaft - Diameter 5/16" • Free Set Of Hands and • Front Loading Hanger Mounting Hardware With • Accurate Within 2 Minutes A Year Each Clock Movement • Fits 3" Diameter Hole • Made in USA 1. Drill a 3/8" hole through the material you are working with and insert the movement. 2. Slide brass washer over shaft. 3. Attach dial mounting hex nut. 4. Gently press hour hand onto shaft at 12:00 position. 5. Place minute hand over shaft at 12:00 position. 6. Gently screw minute nut in place. 7. Press on second hand at 12:00 position. 8. Screw on cap nut if no second hand is used. Mini Movements Shaft Length Selecting the Proper Shaft Length Dials B A P r i c e E a c h P e r P k g O f Proper shaft length is important to ensure Stock# up to Thread Total 1 3 10 50 100 sufficient clearance when going through your dial Q-11 1/8" thick 3/16" 17/32" 4.95 4.23 4.45 3.80 4.25 3.63 3.95 3.38 3.75 3.21 board and when using a glass front on your clock. Q-12 1/4" thick 5/16" 5/8" 4.95 4.23 4.45 3.80 4.25 3.63 3.95 3.38 3.75 3.21 Overall Length (A) is measured from the tip of Q-13 3/8" thick 7/16" 3/4" 4.95 4.See23 4.4 website5 3.80 4.25 3for.63 3current.95 3.38 3.75 3.21 the hand shaft to the movement cast. Allow an Q-14 1/2" thick 9/16" 7/8" 4.95 4.23 4.45 3.80 4.25 3.63 3.95 3.38 3.75 3.21 extra 1/8" for a cap nut or a sweep second hand. pricing The threaded length of the shaft (B) secures your Q-15 5/8" thick 11/16" 1" 4.95 4.23 4.45 3.80 4.25 3.63 3.95 3.38 3.75 3.21 movement to the dial board or wood. Measure Q-16 3/4" thick 15/16" 1-1/4" 4.95 4.23 4.45 3.80 4.25 3.63 3.95 3.38 3.75 3.21 the thickness of the material through which the Q-COV Movement Cover .95 .812 .85 .726 .75 .641 shaft must pass, add the dial or face thickness and Canadian Dollar Pricing in Blue / U.S. Dollar Pricing in Green allow about 1/8" for mounting hardware to get the proper shaft length for your clock project. Clock Hands Please choose one set of FREE black or brass hands with each quartz clock movement ordered. Size is determined by the measurement of the minute hand from the center of the mounting hole to the tip, up to 1/4" can be trimmed if necessary. Black hands can be spray painted any colour. Each set of hands include a red sweep second hand. CLOCK HANDS (Free with each movement) Style Length of Stock # # Minute Hand Black Brass 1-7/8" QH-101 QH-102 2-1/8" QH-103 QH-104 2-1/2" QH-105 QH-106 1 2-7/8" QH-107 QH-108 3-3/8" QH-109 QH-110 4-1/2" QH-111 QH-112 2 3-3/4" QH-205 QH-206 33-3/8" QH-307 QH-308 4 2-1/16" QH-403 QH-404 2-1/16" QH-505 QH-506 5 3-1/8" QH-507 QH-508 6 1-7/8" QH-601 QH-602 2-5/8" QH-703 QH-704 7 Mini Movement Cover 3-5/8" QH-705 QH-706 Our cover provides a neater, more 8 2-3/4" QH-801 QH-802 professional look to clocks with Clock hands are available separately at $1.25 per set exposed movements. It completely covers the back of the movement Tip: When choosing hands to match your clock dial, divide the dial including the battery. diameter by 2 to get an approx. maximum size for your minute hand. 40 Order On-Line at www.woodparts.ca (Canada) or www.bearwood.com (USA) Quartz Pendulum & Chime Clock Movements 1 2 1. Mini Size Quartz Pendulum Movement Ideal for compact cases, it has a step second hand, runs on a single 3 4 & 5 “AA” battery and comes with a 10 year warranty. It is 2-1/8" wide x 3- 3/8" high x 7/8" deep. Free set of hands, mounting hardware and 3 & 4. Traditional Westminster Chime adjustable Brass Pendulum Bob (3 sizes to choose from) included with Full-sized quartz movement plays the traditional Westminster each movement. Chimes melody of a grandfather clock every quarter hour, as well 2. Standard Size Quartz Pendulum Movement as counting out the hours on the hour. A great choice for wall, High quality movement comes with a 10 year warranty. It has a front desk and mantle clocks. Style (3) is 3" wide x 4-5/8" high x 1-1/4" loading hanger, a step second hand and runs on a single “C” cell battery. deep. Style (4) is 3"W x 3-3/4"H. It has a front loading hanger, a This movement is 3" wide x 3-1/2" high x 1" deep. Free set of hands, step second hand and runs on a single “C” cell battery. Free hands mounting hardware and adjustable Brass Pendulum Bob (3 sizes to choose and mounting hardware included. Adjustable Brass Pendulum Bob from) included with each movement. included with style (3) pendulum movement. 1 year warranty. Mini Pendulum Shaft Length Dials B A Shaft Price Each Per Pkg Of 5. Quartz 6 Melody Chime Stock# up to Thread Total Diam 1 3 10 Choose from Ave Maria, Over the Rainbow. Try to Remember, Q-31 1/4"thick 5/16" 5/8" 5/16" 14.95 12.78 13.95 11.92 12.95 11.07 Happy Birthday, Westminster Chime and Rudolph the Red Nosed Q-33 3/8"thick 7/16" 3/4" 5/16" 14.95 12.78 13.95 11.92 12.95 11.07 Reindeer by turning the selection knob on the back of the 1 Q-35 5/8"thick 11/16" 1" 5/16" 14.9512.78 13.9511.92 12.95 11.07 movement. Every hour the chosen melody will play. Movement is Q-37 3/4"thick 15/16" 1-1/4" 5/16" 14.95 See12.78 1website3.95 11.92 1for2.95 11.07 3" wide x 3-3/4" high x 1-1/4" deep. It has a front loading hanger, Standard Pendulum 1current 3pricing 10 a step second hand and runs on a single “C” cell battery. Free Q-42 3/8" 7/16" 3/4" 7/16" 16.95 14.49 15.95 13.63 14.95 12.78 hands and mounting hardware included. 1 year warranty. 2 Q-44 5/8" 11/16" 1" 7/16" 16.95 14.49 15.95 13.63 14.95 12.78 Westminster Chime Shaft Length Q-46 3/4" 15/16" 1-1/4" 7/16" 16.95 14.49 15.95 13.63 14.95 12.78 Dials B A Shaft Price Each in Pkg of Canadian Dollar Pricing in Blue / U.S. Dollar Pricing in Green Stock# Up To Threaded Overall Dia. 1 3 Q-25 3/8"thick 7/16" 3/4" 43.95 37.56 39.95 34.15 4 7/16" Rod & Bob ( FREE with each pendulum movement ) Q-27 5/8"thick 11/16" 1" 43.95 37.56 39.95 34.15 5 Q-29 3/8"thick 7/16" 3/4" 7/16" 4See3.95 3website7.56 39.95 3for4.15 Size 2-1/8" 2-3/4" 3-1/2" Pendulum Chime current pricing3 Stock # QB-218 QB-234 QB-312 Q-53 3/8" 7/16" 3/4" 43.95 37.56 39.95 34.15 3 Q-55 5/8" 11/16" 1" 7/16" 43.95 37.56 39.95 34.15 Q-57 3/4" 15/16" 1-1/4" 43.95 37.56 39.95 34.15 Time & Canadian Dollar Pricing in Blue / U.S. Dollar Pricing in Green Tide Movement Tide 6 7 and Dials Movement 3" Tide hand included This quartz time and tide movement tells you both the time as 8 well as the tide! It has the ability to run the standard hour, 9 minute and second hands as well as a tide hand. 3/8" threaded Based on the lunar day of 24 hours and 50 minutes, this movement shaft for up to 5/16" dial thickness. White time and tide dials tells the general time of high and low tide. Accommodates dials up available in 6" and 7-3/4" diameters. Includes trimmable tide to 1/4" thick. Movement size: 2-1/4"H x 2-1/4"W x 5/8"Diameter. hand and choice of clock hands (page 22). 1-Year warranty.Size Shaft diameter: 5/16". Built in hanger. 6-year replacement warranty 2-1/8"W x 2-7/8"H x 1"D. Requires one “AA” battery. on the movement.
Load more

Recommended publications
  • Measurement of Time
    Measurement of Time M.Y. ANAND, B.A. KAGALI* Department of Physics, Bangalore University, Bangalore 560056 *email: [email protected] ABSTRACT Time was historically measured using the periodic motions of the sun and stars. Various types of sun clocks were devised in Egypt, Greece and Europe. Different types of water clocks were assembled with ever greater accuracy. Only in the seventeenth century did the mechanical clock with pendulums and springs appeared. Accurate quartz clocks and atomic clocks were developed in the first half of the twentieth century. Now we have clocks that have better than microsecond accuracy. This article gives a brief account of all these topics. Keywords: Sun clocks, Water clocks, Mechanical clocks, Quartz clocks, Atomic clocks, World Time, Indian Standard time We all know intuitively what time is. It can be civilizations relied upon the apparent motion of roughly equated with change or motions. From these bodies through the sky to determine the very beginning man has been interested in seasons, months, and years. understanding and measuring time. More We know little about the details of recently, he has been looking for ways to limit timekeeping in prehistoric eras, but we find the “damaging” effects of time and going that in every culture, some people were backward in time! preoccupied with measuring and recording the Celestial bodies—the Sun, Moon, planets, passage of time. Ice-age hunters in Europe over and stars—have provided us a reference for 20,000 years ago scratched lines and gouged measuring the passage of time. Ancient holes in sticks and bones, possibly counting the Physics Education • January − March 2007 277 days between phases of the moon.
    [Show full text]
  • The Case of Switzerland and the World Watch Industry *
    469 Technological discontinuities and flexible production networks: The case of Switzerland and the world watch industry * Amy Glasmeier tain and augment their competitiveness in a global Unrr~rs~t~of Texas at Austin, Texas, USA economy. On the eve of the electronics revolution, the Swiss watch production system, centered in the mountainous Jura region, was flexible, cost The twentieth-century history of the Swiss watch industry effective, and extremely profitable. Both horizon- illustrates how cultures and industrial production systems ex- tally and vertically disintegrated, the Swiss system perience great difficulty adapting to external change at differ- offered enormous variety while maintaining qual- ent points in time. The current emphasis on production net- ity and timeliness of delivery. “The multiplicity of works - unique reservoirs of potential technological innovation realized through cooperation rather than competition among enterprises, and the competition and emulation firms - lacks a detailed appreciation of historic networks, and that characterized the industry, yielded a product in particular their fragile character in times of economic of superior quality known the world over for high turmoil. While networks can and do promote innovation within fashion, design, and precision” [21, p. 481. an existing technological framework, historical experience sug- Beginning in the 1970s when foreign competi- gests their fragmented, atomistic structure is subject to dis- organization and disintegration during periods of technological tion hurdled technological frontiers in watch change. An exclusive focus on “production” ignores other movements, advancing from mechanical to elec- constraints that are powerful forces governing the reaction tric, electronic, digital and finally quartz technol- abilities of regions. Previous research has largely relied on a ogy, the Jura’s undisputed dominance ended.
    [Show full text]
  • A History of the Citizen Watch Company, from the Pages of Watchtime Magazine
    THE WORLD OF FINE WATCHES SPOTLIGHT www.watchtime.com A HISTORY OF THE CITIZEN WATCH COMPANY, FROM THE PAGES OF WATCHTIME MAGAZINE CCIITTIIZZEENN THe HisTory of ciTizen One of the original Citizen pocket watches that went on THE sale in December 1924 CITIZEN WATCH STORY How a Tokyo jeweler’s experiment in making pocket watches 84 years ago led to the creation of a global watch colossus n the 1920s, the young Emperor of Japan, than the imports. To that end, Yamazaki found - Goto. The mayor was a friend of Yamazaki’s. Hirohito, received a gift that reportedly de - ed in 1918 the Shokosha Watch Research Insti - When the fledgling watch manufacturer was I lighted him. The gift was from Kamekichi tute in Tokyo’s Totsuka district. Using Swiss ma - searching for a name for his product, he asked Yamazaki, a Tokyo jeweler, who had an ambi - chinery, Yamazaki and his team began experi - Goto for ideas. Goto suggested Citizen. A tion to manufacture pocket watches in Japan. menting in the production of pocket watches. watch is, to a great extent, a luxury item, he ex - The Japanese watch market at that time By the end of 1924, they began commercial plained, but Yamazaki was aiming to make af - was dominated by foreign makes, primarily production of their first product, the Caliber fordable watches. It was Goto’s hope that every Swiss brands, followed by Americans like 16 pocket watch, which they sold under the citizen would benefit from and enjoy the time - Waltham and Elgin. Yamazaki felt the time brand name Citizen.
    [Show full text]
  • Analog Clock Headway Movement FAQS
    ANALOG CLOCK HEADWAY MOVEMENT FAQS The links below will work in most PDF viewers and link to the topic area by clicking the link. We recommend Adobe Reader version 10 or greater available at: http://get.adobe.com/reader CONTENTS Analog Clock Headway Movement FAQS .................................................................... 1 Batteries ............................................................................................................................. 2 Atomic Clock Factory Restart ...................................................................................... 2 Supported Time Zones .................................................................................................. 2 Time is Incorrect ............................................................................................................. 2 Clock is incorrect by Hours but minutes are correct .......................................... 3 Daylight Saving Time ..................................................................................................... 3 Manually Set Time ........................................................................................................... 3 How long will the battery last? .................................................................................. 3 Can I shut off the WWVB signal? .............................................................................. 3 Is there a booster antenna to receive the WWVB signal in a difficult location? ............................................................................................................................
    [Show full text]
  • SETTING up and MOVING a PENDULUM CLOCK by Brian Loomes, UK
    SETTING UP AND MOVING A PENDULUM CLOCK by Brian Loomes, UK oving a pendulum This problem may face clock with anchor the novice in two different Mescapement can ways. Firstly as a clock be difficult unless you have that runs well in its present a little guidance. Of all position but that you need these the longcase clock to move. Or as a clock is trickiest because the that is new to you and that long pendulum calls for you need to assemble greater care at setting it in and set going for the very balance, usually known as first time—such as one you have just inherited or bought at auction. If it is the first of these then you can attempt to ignore my notes about levelling. But floors in different rooms or different houses seldom agree Figure 1. When moving an on levels, and you may eight-day longcase clock you eventually have to follow need to hold the weight lines through the whole process in place by taping round the of setting the clock level accessible part of the barrel. In and in beat. a complicated musical clock, Sometimes you can such as this by Thomas Lister of persuade a clock to run by Halifax, it is vital. having it at a silly angle, or by pushing old pennies or wooden wedges under the seatboard. But this is hardly ideal and next time you move the clock you start with the same performance all over again. setting it ‘in beat’. These My suggestion is that you notes deal principally with bite the bullet right away longcase clocks.
    [Show full text]
  • 77A71 Quartz Clock Movement Instructions
    77A71 07/28/94 Quartz Clock Movement Instructions Product #3722X, 3723X The 3622X and 3723X quartz battery movements will operate The 3723X movement has a start-stop switch on the rear of the approximately 12 months on a fresh “C” alkaline battery. Insert the case. Both movements feature a hand set knob on the rear of the battery with positive end to your left as movement is held upright case. Telephone time recordings are generally adequate for setting looking from the rear. the time. The 3722X and 3723X movements should keep time to +/- To mount the movement, insert the handshaft through the center 10 seconds per month. hole in your dial and fasten with the brass nut and brass washer. Be sure to use a fresh battery when you install your clock. If you are The hanger and one or more shims (rubber washer) may be neces- not sure, have it tested on a battery testing device. Do not attempt sary between the movement and the dial to control the distance that to disassemble the movement case for any kind of service. the handshaft protrudes through the dial. (See Diagram A) The adjustable pendulum on the 3722X adjustable pendulum Press the hour hand onto its shaft, making sure it does not rub movement has no bearing on the time keeping of the movement against the dial. The minute hand fits onto the threaded “I” shaft itself and can be adjusted by “breaking” the brass rod at the scored and is held by a small nut. The second hand (optional) may now be lines and then replacing the brass bob.
    [Show full text]
  • Mechanical Parts of Clocks Or Watches in General
    G04B CPC COOPERATIVE PATENT CLASSIFICATION G PHYSICS (NOTES omitted) INSTRUMENTS G04 HOROLOGY G04B MECHANICALLY-DRIVEN CLOCKS OR WATCHES; MECHANICAL PARTS OF CLOCKS OR WATCHES IN GENERAL; TIME PIECES USING THE POSITION OF THE SUN, MOON OR STARS (spring- or weight-driven mechanisms in general F03G; electromechanical clocks or watches G04C; electromechanical clocks with attached or built- in means operating any device at pre-selected times or after predetermined time intervals G04C 23/00; clocks or watches with stop devices G04F 7/08) NOTE This subclass covers mechanically-driven clocks or clockwork calendars, and the mechanical part of such clocks or calendars. WARNING In this subclass non-limiting references (in the sense of paragraph 39 of the Guide to the IPC) may still be displayed in the scheme. Driving mechanisms 1/145 . {Composition and manufacture of the springs (compositions and manufacture of 1/00 Driving mechanisms {(driving mechanisms for components, wheels, spindles, pivots, or the Turkish time G04B 19/22; driving mechanisms like G04B 13/026; compositions of component in the hands G04B 45/043; driving mechanisms escapements G04B 15/14; composition and for phonographic apparatus G11B 19/00; springs, manufacture or hairsprings G04B 17/066; driving weight engines F03G; driving mechanisms compensation for the effects of variations of for cinematography G03B 1/00; driving mechnisms; temperature of springs using alloys, especially driving mechanisms for time fuses for missiles F42C; for hairsprings G04B 17/227; materials for driving mechnisms for toys A63H 29/00)} bearings of clockworks G04B 31/00; iron and 1/02 . with driving weight steel alloys C22C; heat treatment and chemical 1/04 .
    [Show full text]
  • This Is Part 1 of 2 on Servicing the 400-Day (Anniversary) Clock
    1 This is part 1 of 2 on servicing the 400-day (Anniversary) clock. This article will be a 2-part series devoted to the servicing of the 400-day or Anniversary clock by Michael P. Murray. Mike was AWI’s 400-day clock repair bench course Instructor. The 400-day course is a 2-day “hands on” affair with the students working on the clock that they bring and Mike can accommodate anywhere from 8 to 16 students. For more information about Mike please see his Website at: http://www.atmosman.com/400dayin.html . This article is copyrighted to the author and references. Members, In my initial series on the 400-day clock, we will cover final assembly right through final timing. My assumption is that we all know the basics but it’s the last seemingly basis steps where most of the troubles occur when servicing this slightly temperamental timepiece. My goal in writing these articles is to get you past many of the pitfalls and erroneous assumptions. There are no real “secrets” and I hope to enable anyone who reads this by dispelling any fears or myths. So if you’re not currently servicing the 400-day, I urge you to give them another try. Series Assumptions A quick mention of what I expect as the “basis”. You’re checked for and corrected any pivot, tooth, or gear depthing problems (depthing problems are extremely rare), used a mainspring winder to remove and install the mainspring, cleaned and lubricated same, pegged all pivot holes, polished all pivots and pivot shoulders, polished the anchor pin and the inside of the fork tines, and cleaned all parts.
    [Show full text]
  • From Sundials to Atomic Clocks
    2 I. THE RIDDLE OF TIME 1. The Riddle of Time 3 The Nature of Time 4 What Is Time? 5 Date, Time Interval, and Synchronization 6 Ancient Clock Watchers 7 Clocks in Nature 9 Keeping Track of the Sun and Moon 10 Thinking Big and Thinking Small-An Aside on Numbers 12 2. Everything Swings 15 Getting Time from Frequency 17 What Is a Clock? 19 The Earth-Sun Clock 20 Meter Sticks to Measure Time 22 What Is a Standard? 23 How Time Tells Us Where in the World We Are 24 Building a Clock that Wouldn’t Get Seasick 26 3 P Chapter C m234567 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 It’s present everywhere, but occupies no space. We can measure it, but we can’t see it, touch it, get rid of it, or put it in a container. Everyone knows what it is and uses it every day, but no one has been able to define it. We can spend it, save it, waste it, or kill it, but we can’t destroy it or even change it, and there’s never any more or less of it. F “SE WE USE IT EVERY DAY! BUT WHAT 4 All of these statements apply to time. Is it any wonder that scientists like Newton, Descartes, and Einstein spent years studying, thinking about, arguing over, and trying to define time-and still were not satisfied with their answers? Today’s scientists have done no better.
    [Show full text]
  • INSTRUCTIONS for ANALOGUE QUARTZ and MECHANICAL WATCHES ✩ Some Models Have a Screw Down Crown Instead of a Standard Crown
    INSTRUCTIONS FOR ANALOGUE QUARTZ AND MECHANICAL WATCHES ✩ Some models have a screw down crown instead of a standard crown. •How to unlock the crown: Unscrew the crown by turning it counterclockwise. Then, pull it out for time/calendar setting. Your watch is one of the following six types of analogue quartz and mechanical watches. •How to lock the crown: Push the crown back to the normal position. Then, turn it clockwise while pressing it until it Before using your new watch, please read the instructions pertaining to your watch type; they locks in place. will help you to get the best out of the watch. • When using the watch in water: Before using the watch in water, make sure the crown is screwed in completely. Do not operate the crown when the watch is wet or in water. A Two hands without calendar D Three hands without calendar ■ Calibre number of your watch Please check the case back of your watch to find the calibre number inscribed on it, B Two hands with date calendar E Three hands with date calendar and read the instructions pertaining to your watch calibre number. It is a 4-digit C Two hands with F Three hands with number to the left of the hyphen mark. day and date calendar day and date calendar MECHANICAL WATCHES : Cal. 4206, 4207, 4217, 7002, 7009, 7019, 4R15, 4R16, 4S15, 7S25, 7S26, 7S35, 7S36, 7S55 ANALOGUE QUARTZ WATCHES : All other calibres [DISPLAY AND HANDS] Hour hand Minute hand Crown ✩ Calibre No. Date Second hand Day 4 5 ■ How to start a mechanical watch Note: When setting the minute hand of a quartz watch, advance it to a few minutes ahead of the time and then turn it back to the exact time.
    [Show full text]
  • PARTS LIST / TECHNICAL GUIDE Automatic Cal
    PARTS LIST / TECHNICAL GUIDE Automatic Cal. 4R35B/4R36A [SPECIFICATIONS] Cal. No. Item 4R35B/4R36A The figures below are Cal. 4R36A. Movement size • Diameter • 3 hands Outside: Ø 27.4 mm (hour, minute and second hands) Casing: Ø 27.0 mm • Day and Date indication • Height: 5.32 mm 4R35B 4R36A Outside diameter Ø 27.4 mm Ø 27.4 mm Movement size Casing diameter Ø 27.0 mm Ø 27.0 mm Height 5.32 mm 5.32 mm Driving system Automatic winding with manual winding mechanism • 3 hands • 3 hands Time indication (Hour, Minute, and Small second hands) (Hour, Minute, and Small second hands) • Date indication • Day and date indication • Date correction function • Date correction function • Day correction function Additional function • Second hand stop function • Second hand stop function Normal position Manual winding (clockwise only) Manual winding (clockwise only) Crown 1st click position Date setting (counterclockwise) Date setting (counterclockwise), Day setting operation 2nd click position Time setting (Hour and minute), Second hand stop Vibration per hour 21,600 (6 beats per second) Daily rate worn on the wrist at temperature range Between +45 and -35 seconds between 5 °C and 35 °C) Mainspring wind After 24 hours Fully wind up Loss/Gain up status from fully wind up Dial upward: Dual upward: Standard rate for Testing positions 6 o’clock at the top 9 o’clock at the top measurement T0 (CH) T24 (CH) Measurement (Isochronism (daily rate in ± 20 s/d ± 30 s/d ± 30 s/d fault: T24-T0) seconds: s/d) ± 30 s/d Regulation system ETACHRON System Lift angle of the escapement 53 ° Power reserve From fully wound to stoppage: Approximately 40 hours Number of jewels 24 jewels PARTS LIST Cal.
    [Show full text]
  • MD–90 Series Precision Quartz Clock Manufactured by Mid-Continent Instruments and Avionics
    MD–90 Series Precision Quartz Clock Manufactured by Mid-Continent Instruments and Avionics PRECISION QUARTZ CLOCK PRECISION QUARTZ THE MD – 90 SERIES IS DESIGNED FOR ACCURACY AND IS TRUSTED BY MANY AIRCRAFT MANUFACTURERS MD–90 AND OWNERS. Accurate time-keeping is important to an instrument pilot, Precision quartz movement and it is a requirement that a timepiece with a sweep second Compact 2-inch size — fits standard panel cutout pointer be on board the airplane. The MD–90 Series Precision Lighted version available with field-replaceable light tray Quartz Clock is the ideal solution. Transient and reverse polarity protected The 2-inch MD–90 Series features extremely low current Original equipment for many major aircraft manufacturers draw, transient and reverse polarity protection. Each clock is Low power consumption (3 mA) manufactured to meet rugged aircraft environmental standards. Continuously powered by aircraft battery With a high-quality, solid-state quartz movement and a variety of lighting options, a 12-hour analog clock is an essential FAA PMA certified part of any instrument panel. Designed and built in Wichita, Kansas, USA One-year limited warranty Kansas 9400 East 34th Street North Wichita, Kansas 67226 USA Tel 316.630.0101 Tel 800.821.1212 Fax 316.630.0723 E-mail [email protected] California 16320 Stagg Street Van Nuys, California 91406 USA Tel 818.786.0300 Tel 800.345.7599 Fax 818.786.2734 E-mail [email protected] mcico.com MD–90 Series Precision Quartz Clocks Manufactured by Mid-Continent Instruments and Avionics SPECIFICATIONS Power Input 8–32 VDC 3 mA max (without lighting) Accuracy ±30 seconds in 24 hrs Dimensions 2.5 x 2.5 x 3.2 inches max Weight 0.5 lbs Temperature –40°C to +82°C (–40°F to +180°F) Altitude –1,000 to +55,000 ft Humidity 0 to 95% at 25°C Vibration 02 in.
    [Show full text]